Environmental pollution by antibiotics and by antibiotic resistance determinants

Antibiotics are among the most successful drugs used for human therapy. However, since they can challenge microbial populations, they must be considered as important pollutants as well. Besides being used for human therapy, antibiotics are extensively used for animal farming and for agricultural purposes. Residues from human environments and from farms may contain antibiotics and antibiotic resistance genes that can contaminate natural environments. The clearest consequence of antibiotic release in natural environments is the selection of resistant bacteria. The same resistance genes found at clinical settings are currently disseminated among pristine ecosystems without any record of antibiotic contamination. Nevertheless, the effect of antibiotics on the biosphere is wider than this and can impact the structure and activity of environmental microbiota. Along the article, we review the impact that pollution by antibiotics or by antibiotic resistance genes may have for both human health and for the evolution of environmental microbial populations.     

Treatment of phenolic wastewater by horseradish peroxidase immobilized by bioaffinity layering

Horseradish peroxidase was immobilized by bioaffinity layering and used for the treatment of wastewater containing p-chlorophenol. For this purpose, lectin Concanavalin A was bound to Sephadex beads. The glycoenzyme peroxidase was layered upon this Con A layer. Subsequently, alternate layers of the enzyme and Con A were applied. The most efficient design consisted of three layers of Con A and peroxidase each. This immobilized enzyme preparation retained 80% of the activity of the free peroxidase used for immobilization. PEG at the concentration of 0.1 mg ml(-1) was found to prevent enzyme inactivation by the products, although it increased the process time. Thus 60 U ml(-1) of enzyme completely converted the p-chlorophenol (into products) in 4 min in the absence of PEG. On the other hand, only 0.05 U ml(-1) of enzyme was required for this purpose in the presence of PEG but the process required 60 min. Peroxidase converts phenol molecules into free radicals. These free radicals then polymerize and get precipitated. As a further means of minimizing exposure of the enzyme to free radicals and enhancing the reusability, it was decided to remove the enzyme from reaction medium after 10 min. With this strategy, the bioaffinity layered peroxidase preparation could be reused five times without any loss of activity.     

Absorption of selenium by Lactuca sativa as affected by carboxymethylcellulose

Several organic compounds of high molecular weight present in soil interact with selenium and may act as active binding agents affecting its availability in soil, and, consequently, selenium uptake by plants. This study is aimed at investigating the effects of polysaccharides on selenium speciation in soil and on selenium absorption by Lactuca sativa L. plants. Three-week-old seedlings were transplanted into pots filled with soil, and sodium selenite at rates of 1.5 and 5mgSekg(-1) of soil, or sodium selenate at a rate of 1.5mgSekg(-1) of soil were applied. Carboxymethylcellulose (CMC) was added to the soil at rates of 0, 3 and 30mgkg(-1) of soil. After 48 and 110d from transplanting plants were harvested, separated into root and shoot, and fresh and dry matter weights were recorded. Total selenium was determined in both soil and plant samples. A sequential extraction was used to investigate the different Se oxidation states and assess the availability of Se in soil after the final harvesting. Both selenite and selenate were absorbed by roots, but plants amended with Se(VI+) showed higher selenium concentration than plants amended with Se(IV+). Selenite appears to be less mobile than selenate both in soil and plants. The addition of carboxymethylcellulose to soil decreased the amount of selenium absorbed by plants. CMC interacted with Se, making it less mobile as evidenced by the increase in the insoluble fractions. The insoluble Se forms in soil may represent environmental Se sinks potentially available for plants if the substrate is re-used for subsequent growth cycles and selenium species are mobilized as a result of biological and chemical processes.     

盆栽植物净化甲苯废气

采用动态模拟法模拟盆栽植物对甲苯污染气体的净化,考察吊兰和金绿萝两种盆栽植物在净化甲苯过程中,甲苯入口浓度与植物对甲苯净化速率的关系。结果表明,2种盆栽植物对低浓度甲苯废气具有长期明显的净化效果。在相同条件下,吊兰茎叶和土壤的净化速率优于金绿萝体系。在植物的耐受浓度范围内,2种植物茎叶和土壤的净化速率均随着甲苯入口浓度的升高而增大,且白天的净化速率明显高于黑夜时的净化速率。在实验过程中,吊兰土壤体系的降解率随着甲苯浓度的升高逐渐下降;金绿萝土壤体系的降解率基本不受甲苯入口浓度的影响。吊兰盆栽体系的降解率明显大于金绿萝的降解率。两种植物盆栽体系的降解率随甲苯进口浓度的影响可以忽略。     

Highly concentrated phenolic wastewater treatment by the photo-Fenton reaction, mechanism study by FTIR-ATR

Phenol degradation by Photo-Fenton reaction has been studied in highly concentrated wastewaters and most intermediate species have been identified by Fourier Transform IR-Spectroscopy with ATR device. During the photodegradation of highly concentrated phenol solutions, the formation of dissolved and precipitate tannin has been observed. The possibility of a Fe3+-Pyrogallol complex formation, previous to the tannin formation, has been proposed too. The complex formation involving Fe3+ ions could be related to the observed Photo-Fenton activity decrease. Tannin formation inhibits the complete mineralization of phenol because *OH radicals attack will produce further condensation steps and the polymer size increase. This fact limits the applicability of the process for highly concentrated phenolic wastes mineralization. However, the tannin precipitation allows its separation from the solution by conventional filtration, and reduction of the corresponding dissolved organic carbon. These observations have been proved from the identification of primary degradation products, catechol and hydroquinone. Catechol is considered to be the first step for the formation of tannins. Degradation process for phenol, catechol and hydroquinone have been monitored by total organic carbon (TOC) measurements along the reaction time span. From these results, a global mechanism for the Photo-Fenton degradation of phenol is proposed.     

Removal of fluorine from contaminated soil by electrokinetic treatment driven by solar energy

Instead of direct current power supply, a series of electrokinetic remediation experiments driven by solar energy on fluorine-contaminated soil were conducted in a self-made electrolyzer, in order to reduce energy expenditure of electrokinetic remediation. After the 12-day electrokinetic remediation driven by solar energy, the removal efficiency of fluorine was 22.3 %, and electrokinetic treatment had an impact on changes in partitioning of fluorine in soil. It proved that the combination of electrokinetics and solar energy was feasible and effective to some extent for the remediation of fluorine-contaminated soil. Meanwhile, the experimental results also indicated that the electromigration was a more dominant transport mechanism for the removal of fluorine from contaminated soil than electroosmosis, and the weather condition was the important factor in affecting the removal efficiency.     

Ozone removal by HVAC filters

Residential and commercial HVAC filters that have been loaded with particles during operation in the field can remove ozone from intake or recirculated air. However, knowledge of the relative importance of HVAC filters as a removal mechanism for ozone in residential and commercial buildings is incomplete. We measured the ozone removal efficiencies of clean (unused) fiberglass, clean synthetic filters, and field-loaded residential and commercial filters in a controlled laboratory setting. For most filters, the ozone removal efficiency declined rapidly but converged to a non-zero (steady-state) value. This steady-state ozone removal efficiency varied from 0% to 9% for clean filters. The mean steady-state ozone removal efficiencies for loaded residential and commercial filters were 10% and 41%, respectively. Repeated exposure of filters to ozone following a 24-h period of no exposure led to a regeneration of ozone removal efficiency. Based on a theoretical scaling analysis of mechanisms that are involved in the ozone removal process, we speculate that the steady-state ozone removal efficiency is limited by reactant diffusion out of particles, and that regeneration is due to internal diffusion of reactive species to sites available to ozone for reaction. Finally, by applying our results to a screening model for typical residential and commercial buildings, HVAC filters were estimated to contribute 22% and 95%, respectively, of total ozone removal in HVAC systems.     

Predictability by Box-Behnken model for carbaryl adsorption by soils of Indian origin

This study was undertaken to investigate the adsorption capacity of carbaryl on four Indian soils with different physiochemical properties. A batch adsorption study was carried out in order to evaluate the maximum adsorption capacity of carbaryl using a Response Surface Methodology (RSM). The effects of operating parameter such as initial carbaryl concentration (1–20 mgL^?1), adsorbent dosage (0.5–6 g) and contact time (10–180 min) were examined. The proposed quadratic model for Box-Behnken design fits very well to the experimental data because it may be used to navigate design space according to ANOVA results. The regression co-efficient (R²) of the models developed and the results of validation experiments conducted at optimal conditions strongly suggests that the predicted values are in good agreement with experimental results. Contour and response surface plots are used to determine the interactions effects of main factors and optimal conditions of the process. The experiment can be utilized as a guideline for better understanding of carbaryl adsorption onto soil under different operating conditions. The results show that the forest soil is most efficient in binding carbaryl (Sevin) than the other types of soil tested.     

Is pesticide sorption by constructed wetland sediments governed by water level and water dynamics?

Constructed wetlands (CWs) are used to reduce the pesticide inputs from tile drainage or run-off to surface water. Their effectiveness appears variable and remains to be better characterized and understood. The aim of this study was to assess the influences of two hydraulic parameters (i.e., dynamics and water level) on the sorption process occurring in CWs. Then, two solid/liquid ratios were studied (1/1 and 1/5) to mimic the water level variation in the field, and two agitation speeds were used (none and gentle agitation) to simulate different water dynamics (stagnation and flow pass, respectively). Sorption kinetics and isotherms were obtained for four pesticides with contrasting properties. The pesticide adsorption coefficients were classified as follows: boscalid (BSC) > cyproconazole (CYP) > isoproturon (IPU) ～ dimethachlor (DMT) at any ratio or agitation, in agreement with their water solubilities and K _ow values. The effect of the solid/liquid ratio was evidenced for all conditions. Indeed, the adsorption equilibrium time was reached more quickly for the 1/1 ratio (24–72 h) than for the 1/5 ratio (96–120 h). In addition, the adsorption coefficients (K _f ^ads) were larger for the 1/1 ratio (1.8–11.2 L kg^?1) than for the 1/5 ratio (1.0–5.9 L kg^?1). The agitation effect was ?more evidenced for the 1/5 ratio and for the more hydrophobic molecules, such as BSC and CYP, for which adsorption equilibrium time was never reached with agitation (>120 h), while it was reached at 96 h without agitation. Moreover, the K _f ^ads values were larger with agitation than without agitation for BSC and CYP, whereas they were similar for the two agitations for IPU and DMT. Our results demonstrated that the hydrodynamic function of CWs could influence pesticide sorption with variable effects according to the molecular properties and consequently influence the mitigation effect of CWs throughout the year.     

The entrapment of particles by windbreaks

A theory is developed for calculating the entrapment of particles by a windbreak, with four results. (1) The fraction of particles in the oncoming flow which pass through the windbreak, or transmittance of the windbreak for particles (σ), is related to the optical porosity (τ). The very simple approximation σ=τ works well for most applications involving the interception of spray droplets by windbreaks. Results from a field experiment agree with the theoretical predictions. (2) A new equation for the bulk drag coefficient of a windbreak is tested against numerical, wind tunnel and field experiments. This enables the bleed velocity for the flow through the windbreak to be predicted in terms of the screen pressure coefficient (k) of the barrier. (3) The relationship between k and τ is different for a vegetative barrier than for a screen across a confined duct, implying a lower k for given τ. (4) The total deposition of particles to a windbreak is determined by a trade-off between particle absorption and throughflow, implying an optimum value of τ for maximum total deposition. For particles larger than 30 μm and vegetation elements smaller than 30 mm, this occurs near τ=0.2.     

Effect of soil sterilization by mercuric chloride on herbicide sorption by soil

Microbial inhibitors such as mercuric chloride are frequently used to sterilize soil or soil-water slurries in experimental studies on the fate of xenobiotics in the environment. This study examined the influence of mercuric chloride additions to soil-water slurries on the sorptive behaviour of a phenoxy herbicide (2,4-D) in soil. The results demonstrated that mercuric chloride strongly decreased the capacity of the soil to retain herbicides, and that the interference of mercuric chloride with herbicide sorption increased with increasing soil organic carbon contents. Because of the competitive sorption between mercuric chloride and the phenoxy herbicide, we conclude that mercuric chloride may not be a good soil sterilization procedure for use in xenobiotic fate studies.     

紫外线杀菌效能的研究

自来水的消毒目前普遍采用氯及含氯化合物药剂，消毒过程中产生三卤甲烷等致癌或致突变物质，从而造成水体的二次污染，许多国家已经禁止在消毒中使用含氯药剂。因此，具有安全可靠高效杀菌作用的紫外线消毒技术逐渐发展起来，并越来越受到人们的关注。但是紫外线的使用也有一定的限制，通过紫外线照射时间及进水浊度的变化，研究了具有一定照射强度的紫外灯的杀菌效能变化，并得出了紫外线具有最佳杀菌效果的进水极限浊度和照射时间。同时还研究了紫外线对具有不同抗性的细菌的系灭效率，为饮用水和污水的消毒处理提供了实验基础。     

Comparison of naphthalene bioavailability determined by whole-cell biosensing and availability determined by extraction with Tenax

A rapid biological method for the determination of the bioavailability of naphthalene was developed and its value as an alternative to extraction-based chemical approaches demonstrated. Genetically engineered whole-cell biosensors are used to determine bioavailable naphthalene and their responses compared with results from Tenax extraction and chemical analysis. Results show a 1:1 correlation between biosensor results and chemical analyses for naphthalene-contaminated model materials and sediments, but the biosensor assay is much faster. This work demonstrates that biosensor technology can perform as well as standard chemical methods, though with some advantages including the inherent biological relevance of the response, rapid response time, and potential for field deployment. A survey of results from this work and the literature shows that bioavailability under non-equilibrium conditions nonetheless correlates well with K_oc or K_d. A rationale is provided wherein chemical resistance is speculated to be operative.     

Decolourisation of simulated reactive dyebath effluents by electrochemical oxidation assisted by UV light

This study is focused on the optimisation of the electrochemical decolourisation of textile effluents containing reactive dyes with the aim of making feasible-technically and economically-this method at industrial scale. Coloured waters were treated in continuous at low current density, to reduce the electrical consumption. Ti/PtO(x) electrodes were used to oxidize simulated dyebaths prepared with an azo/dichlorotriazine reactive dye (C.I. Reactive Orange 4). The decolourisation yield was dependent on the dyeing electrolyte (NaCl or Na(2)SO(4)). Dyeing effluents which contained from 0.5 to 20 gl(-1) of NaCl reached a high decolourisation yield, depending on the current density, immediately after the electrochemical process. These results were improved when the effluents were stored for several hours under solar light. After the electrochemical treatment the effluents were stored in a tank and exposed under different lighting conditions: UV light, solar light and darkness. The evolution of the decolourisation versus the time of storage was reported and kinetic constants were calculated. The time of storage was significantly reduced by the application of UV light. A dye mineralization study was also carried out on a concentrated dyebath. A TOC removal of 81% was obtained when high current density was applied for a prolonged treatment with recirculation. This treatment required a high electrical consumption.     

Biodegradation of pyrene by sediment fungi

Micromycetes were isolated from PAHS-contaminated sediment and identified. They were investigated for pyrene degradation (10 mg l-1) in liquid synthetic medium for two days. Among the 41 strains isolated, 10 highly degraded pyrene (> 2.4 mg g-1 dry weight): two Zygomycetes (Mucor racemosus, M. racemosus var. sphaerosporus), 6 Deuteromycetes (Gliocladium virens, Penicillium simplicissimum, P. janthinellum, Phialophora alba, P. hoffmannii, Trichoderma harzianum), a Dematiaceae (Scopulariopsis brumptii) and a Sphaeropsidale (Coniothyrium fuckelii). Zygomycetes appeared as one of the most efficient taxonomic groups, especially with Mucor racemosus. Penicillium crustosum was the only strain that did not degrade pyrene. Among the 10 fungi which were performant for pyrene degradation, nine were not yet reported in the literature and showed a real value for PAH remediation.     

Aerosol Filtration by Sorbent Beds

Fixed beds of sorbent media are used for the evaluation of poiynuclear aromatic hydrocarbons (PAH) present in air. Twostage sampling and separate extraction and analyses of PAH associated with aerosol particles and those present in the vapor state are usually performed. The ability of commonly used sorbents to retain particulate matter introduces a potential for reducing the time and cost of PAH evaluation procedures.

The filtration efficiency of three sorbent media, Florisil, XAD-2, and polyurethanefoam (PUF), for particles in 0.1 to 1 µm size range was studied using airflow rates from 4 to 2501 /mm through a PS 1 sorbent cartridge. Theoretical considerations were used to identify the principal filtration mechanisms and to assess the predictability of the aerosol filtration performance of sorbent filters. The results of this study indicate XAD-2 to be an efficient filtration medium owing to the electrostatic enhancement of capturing and retaining aerosol particles.

As a result of theoretical considerations, Brownian diffusion and inertial deposition were found to be major filtration mechanisms accompanied by electrostatic effects. While the efficiency of the diffusional deposition mechanism was reasonably well predicted with available theories, modeling of submicron particle impaction at higher fluid velocities appeared to be inadequate. Further developments are suggested to improve our understanding of filtration phenomena in sorbent beds under high flow rate conditions.     

Meta-analysis of environmental contamination by phthalates

Phthalate acid esters (PAE), commonly named phthalates, are toxics classified as endocrine-disrupting compounds; they are primarily used as additives to improve the flexibility in polyvinyl chloride. Many studies have reported the occurrence of phthalates in different environmental matrices; however, none of these studies has yet established a complete overview for those compounds in the water cycle within an urban environment. This review summarizes PAE concentrations for all environmental media throughout the water cycle, from atmosphere to receiving waters. Once the occurrences of compounds have been evaluated for each environmental compartment (urban wastewater, wastewater treatment plants, atmosphere, and the natural environment), we reviewed data in order to identify the fate of PAE in the environment and establish whether geographical and historical trends exist. Indeed, geographical and historical trends appear between Europe and other countries such as USA/Canada and China, however they remain location dependent. This study aimed at identifying both the correlations existing between environmental compartments and the processes influencing the fate and transport of these contaminants into the environment. In Europe, the concentrations measured in waterways today represent the background level of contamination, which provides evidence of a past diffuse pollution. In contrast, an increasing trend has actually been observed for developing countries, especially for China.     

Aniline degradation by electrocatalytic oxidation

The degradation of aniline solution in alkaline medium of pH 11.0 by electrocatalytic oxidation has been studied using an electrochemical reactor containing a SnO₂–Sb₂O₃–PtO anode and a Ti cathode, both of 54 cm² area. Hydroxyl radicals (HO^√) are produced at the anode, being tested with the trace catcher salicylic acid and phenol by spectrophotometery and high performance liquid chromatography. Intermediates dianiline, 4-anilino phenol and azobenzol were detected by gas chromatography–mass spectrometry. The existence of HO^√ produced in the aniline degradation was assayed with scavenger tertiary butanol. The results showed that electrocatalytic oxidation is an effective process for the degradation of aniline. A general reaction pathway that accounts for aniline degradation to CO₂ involving those intermediates is proposed.     

Bioaccumulation and elimination of tetrachlorobenzyltoluene (TCBT) by the rat and by fish

A comparative study has been made of the bioaccumulation and elimination by fish and the rat of (i) tetrachlorobenzyltoluene (TCBT), a substance recently proposed as a substitute for polychlorobiphenyl (PCB), and (ii) DP5, a pentachlorobiphenyl mixture (PCB-5 C1).

The study relating to fish (Brachydanio Rerio) comprised a 30-day accumulation period followed by a 30-day elimination period. Nominal concentrations of TCBT and PCB-5 C1, respectively, in the water, were 1mg/litre in both cases.

The study relating to the rat comprised a 90-day treatment period followed by a 30-day elimination period. The animals were exposed by oral (gavage) to doses of 0, 5, 30, and 200 mg/kg/day in the case of TCBT and to the single dose of 5 mg/kg/day in the case of PCB-5 Cl.

Concentrations of TCBT and PCB-5 Cl in rat liver and fats, in whole body tissues of fish and in water were measured by gas chromatography, using an electron capture detector.

Results showed a clear difference between TCBT and PCB-5 Cl: in fish, bioaccumulation of TCBT was relatively slight and the 50% depuration time was approximately 26 days; in rat liver and fats, TCBT was also only weakly accumulated and rapidly eliminated. This contrasted sharply with the findings for PCB-5 Cl, viz: high accumulation potential and slow elimination.

Observed rates of bioaccumulation and elimination of TCBT and PCB-5 Cl by the rat were in good agreement with the toxicological findings for the same species.     

Accumulation and excretion of chloroanilines by carp

Accumulation and excretion of chloroanilines were studied for carp ( L.). The average bioconcentration factors (BCF) in the whole body of the fish after 24 – 336 hr exposure were 2.0 and 3.7 for o-chloroaniline. 0.8 and 2.2 for m-chloroaniline and 0.8 and 1.7 for p-chloroaniline at high and low concentrations of the chemicals, respectively. The excretion rate constants (k) from the whole body of the fish were 0.19 hr⁻¹ for o-chloroaniline, 0.21 hr⁻¹ for m-chloroaniline and 0.16 hr⁻¹ for p-chloroaniline. The experimental data on the accumulation and excretion of the chloroanilines were consistent with the field data.