Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Recent progress on application of UV excilamps for degradation of organic pollutants and microbial inactivation

Excilamps as modern mercury-free sources of narrow-band UV radiation represent an attractive alternative in environmental applications. This review focuses on recent studies on the water and surface decontamination with excilamps by means of direct photolysis and advanced oxidation processes. To date, direct photolysis and advanced oxidation processes (AOPs) such as UV/H₂O₂, UV/Fenton and UV/O₃ have been applied for degradation of organic compounds (mainly, phenols, dyes and herbicides) in model aqueous solutions. Special emphasis is placed on studies combining UV irradiation (as a pre-treatment or post-treatment step) with biological treatment. In this review, the efficiencies of direct UV, UV/H₂O₂ and UV/TiO₂ processes for inactivation of a variety of pathogenic microorganisms in water and on surfaces are discussed. The analysis of the literature shows that more works need to be done on scaling up the processes, degradation/mineralization of target pollutant(s) in real effluents and evaluation of energy requirements.     

Degradation of bisphenol A by the UV/H2O2 process: a kinetic study

A theoretical and experimental study of bisphenol A (BPA) degradation by the UV/H₂O₂ process in water is presented. The effects of the H₂O₂ concentration and the specific rate of photon emission (E_P,0) on BPA degradation were investigated. A kinetic model derived from a reaction sequence was employed to predict BPA and hydrogen peroxide concentrations over time using an annular photochemical reactor in batch recirculation mode. The local volumetric rate of photon absorption (LVRPA) inside the photoreactor was computed using a Line Source with Parallel Plane emission model (LSPP). From the proposed kinetic model and the experimental data, the second order rate constants of the reactions between hydroxyl radicals and the main reacting species (H₂O₂ and BPA) were estimated applying a nonlinear regression method. A good agreement between the kinetic model and experimental data, for a wide range of operating conditions, was obtained. For BPA, H₂O₂, and TOC concentrations, the calculated root means square errors (RMSE) were 2.3?×?10^??2, 9.8?×?10^??1, and 9.0?×?10^??2 mmol L^??1, respectively. The simplified kinetic model presented in this work can be directly applied to scaling-up and reactor design, since the estimated kinetic constants are independent of the reactor size, shape, and configuration. Further experiments were made by employing low BPA initial concentration (100 μg L^??1) in water and real wastewater. A lower degradation rate of BPA was observed in the real wastewater, although the UV/H₂O₂ process has also been able to completely degrade the target pollutant in less than 1 h.

     

Transformation of sulfaquinoxaline by chlorine and UV light in water: kinetics and by-product identification

Sulfaquinoxaline (SQX) is an antimicrobial of the sulfonamide class, frequently detected at low levels in drinking and surface water as organic micropollutant. The main goal of the present study is the evaluation of SQX reactivity during chlorination and UV irradiations which are two processes mainly used in water treatment plants. The SQX transformation by chlorination and UV lights (254 nm) was investigated in purified water at common conditions used for water disinfection (pH =?7.2, temperature =?25 °C, [chlorine] =?3 mg L^?1). The result shows a slow degradation of SQX during photolysis compared with chlorination process. Kinetic studies that fitted a fluence-based first-order kinetic model were used to determine the kinetic constants of SQX degradation; they were equal to 0.7?×?10^?4 and 0.7?×?10^?2 s^?1corresponding to the half time lives of 162 and 1.64 min during photolysis and chlorination, respectively. In the second step, seven by-products were generated during a chlorination and photo-transformation of SQX and identified using liquid chromatography with electrospray ionization and tandem mass spectrometry (MS-MS). SO₂ extrusion and direct decomposition were the common degradation pathway during photolysis and chlorination. Hydroxylation and isomerization were observed during photodegradation only while electrophilic substitution was observed during chlorination process.     

Facile, effective, and environment-friendly degradation of sulfamonomethoxine in aqueous solution with the aid of a UV/Oxone oxidative process

The degradation of sulfamonomethoxine (SMM) in the aqueous environment by the combination of UV illumination and Oxone has been studied. Experimental results indicated that the UV illumination can effectively activate Oxone to produce sulfate-free radicals (SO₄ ^??). When 10 mmol L^?1 Oxone was added, 96.78 % removal of SMM (5 mg L^?1) was achieved within 90 min. Mineralization of SMM was investigated by measuring the total organic carbon, which decreased by 89.01 % after 90 min reaction. Six intermediate compounds generated during the SMM degradation were identified with the aid of liquid chromatography and mass spectroscopy, combined with proton nuclear magnetic resonance spectroscopy. A general reaction pathway for the degradation of SMM was proposed, where the presence of SO₄ ^?? remained crucial during the degradation process.     

Decomposition of phenylarsonic acid by AOP processes: degradation rate constants and by-products

The paper presents results of the studies photodegradation, photooxidation, and oxidation of phenylarsonic acid (PAA) in aquatic solution. The water solutions, which consist of 2.7 g dm^?3 phenylarsonic acid, were subjected to advance oxidation process (AOP) in UV, UV/H₂O₂, UV/O₃, H₂O₂, and O₃ systems under two pH conditions. Kinetic rate constants and half-life of phenylarsonic acid decomposition reaction are presented. The results from the study indicate that at pH 2 and 7, PAA degradation processes takes place in accordance with the pseudo first order kinetic reaction. The highest rate constants (10.45?×?10^?3 and 20.12?×?10^?3) and degradation efficiencies at pH 2 and 7 were obtained at UV/O₃ processes. In solution, after processes, benzene, phenol, acetophenone, o-hydroxybiphenyl, p-hydroxybiphenyl, benzoic acid, benzaldehyde, and biphenyl were identified.     

Elimination of radiocontrast agent diatrizoic acid by photo-Fenton process and enhanced treatment by coupling with electro-Fenton process

The removal of radiocontrast agent diatrizoic acid (DIA) from water was performed using photo-Fenton (PF) process. First, the effect of H₂O₂ dosage on mineralization efficiency was determined using ultraviolet (UV) irradiation. The system reached a maximum mineralization degree of 60 % total organic carbon (TOC) removal at 4 h with 20 mM initial H₂O₂ concentration while further concentration values led to a decrease in TOC abatement efficiency. Then, the effect of different concentrations of Fenton’s reagents was studied for homogeneous Fenton process. Obtained results revealed that 0.25 mM Fe³⁺ and 20 mM H₂O₂ were the best conditions, achieving 80 % TOC removal efficiency at 4 h treatment. Furthermore, heterogeneous PF treatment was developed using iron-activated carbon as catalyst. It was demonstrated that this catalyst is a promising option, reaching 67 % of TOC removal within 4 h treatment without formation of iron leachate in the medium. In addition, two strategies of enhancement for process efficiency are proposed: coupling of PF with electro-Fenton (EF) process in two ways: photoelectro-Fenton (PEF) or PF followed by EF (PF-EF) treatments, achieving in both cases the complete mineralization of DIA solution within only 2 h. Finally, the Microtox tests revealed the formation of more toxic compounds than the initial DIA during PF process, while, it was possible to reach total mineralization by both proposed alternatives (PEF or PF-EF) and thus to remove the toxicity of DIA solution.     

Efficient removal of insecticide “imidacloprid” from water by electrochemical advanced oxidation processes

The oxidative degradation of imidacloprid (ICP) has been carried out by electrochemical advanced oxidation processes (EAOPs), anodic oxidation, and electro-Fenton, in which hydroxyl radicals are generated electrocatalytically. Carbon-felt cathode and platinum or boron-doped diamond (BDD) anodes were used in electrolysis cell. To determine optimum operating conditions, the effects of applied current and catalyst concentration were investigated. The decay of ICP during the oxidative degradation was well fitted to pseudo-first-order reaction kinetics and absolute rate constant of the oxidation of ICP by hydroxyl radicals was found to be k _abs(ICP)?=?1.23?×?10⁹ L mol^?1 s^?1. The results showed that both anodic oxidation and electro-Fenton process with BDD anode exhibited high mineralization efficiency reaching 91 and 94 % total organic carbon (TOC) removal at 2 h, respectively. For Pt-EF process, mineralization efficiency was also obtained as 71 %. The degradation products of ICP were identified and a plausible general oxidation mechanism was proposed. Some of the main reaction intermediates such as 6-chloronicotinic acid, 6-chloronicotinaldehyde, and 6-hydroxynicotinic acid were determined by GC-MS analysis. Before complete mineralization, formic, acetic, oxalic, and glyoxylic acids were identified as end-products. The initial chlorine and organic nitrogen present in ICP were found to be converted to inorganic anions Cl^?, NO₃ ^?, and NH₄ ⁺.     

Application of Fenton, photo-Fenton, solar photo-Fenton, and UV/H2O2 to degradation of the antineoplastic agent mitoxantrone and toxicological evaluation

In the present study, selected advanced oxidation processes (AOPs)—namely, photo-Fenton (with Fe²⁺, Fe³⁺, and potassium ferrioxalate—FeOx—as iron sources), solar photo-Fenton, Fenton, and UV/H₂O₂—were investigated for degradation of the antineoplastic drug mitoxantrone (MTX), frequently used to treat metastatic breast cancer, skin cancer, and acute leukemia. The results showed that photo-Fenton processes employing Fe(III) and FeOx and the UV/H₂O₂ process were most efficient for mineralizing MTX, with 77, 82, and 90 % of total organic carbon removal, respectively. MTX probably forms a complex with Fe(III), as demonstrated by voltammetric and spectrophotometric measurements. Spectrophotometric titrations suggested that the complex has a 2:1 Fe³⁺:MTX stoichiometric ratio and a complexation constant (K) of 1.47 × 10⁴ M^–1, indicating high MTX affinity for Fe³⁺. Complexation partially inhibits the involvement of iron ions and hence the degradation of MTX during photo-Fenton. The UV/H₂O₂ process is usually slower than the photo-Fenton process, but, in this study, the UV/H₂O₂ process proved to be more efficient due to complexing of MTX with Fe(III). The drug exhibited no cytotoxicity against NIH/3T3 mouse embryonic fibroblast cells when oxidized by UV/H₂O₂ or by UV/H₂O₂/FeOx at the concentrations tested.     

生物淋滤-Fenton对印染污泥脱水性能的影响

采用嗜酸性硫杆菌生物淋滤联合Fenton氧化法对印染污泥脱水性能进行了研究。结果表明,生物淋滤过程中pH下降速率随着硫粉添加量增加而变快,经生物淋滤处理后污泥的脱水性能在一定程度上得到了改善。对生物淋滤后的污泥进行了Fenton氧化处理,获得的最佳反应条件为反应时间2 h,H2O2和Fe2+添加量分别为6 g/L和0.5 g/L。在该条件下,污泥上清液中总有机碳(TOC)由20.8 mg/L增加到356.6 mg/L;污泥比阻(SRF)和滤饼含水率分别由5.98×1011s2/g和88.75%减少至1.26×1011s2/g和82.85%。生物淋滤-Fenton氧化法在污泥破解程度和脱水性能改善方面均优于单独Fenton氧化法。     

Mineralization of dinitrotoluenes and trinitrotoluene of spent acid in toluene nitration process by Fenton oxidation

Fenton's reagent, UV/H2O2 and UV/Fenton's reagent were employed to mineralize dinitrotoluene (DNT) isomers and 2,4,6-trinitrotoluene (TNT) of spent acid in toluene nitration process. The bench-scale experiments were conducted to elucidate the influence of various operating variables on the performance of removal of total organic compounds (TOC) from spent acid, including reaction temperature, concentration of ferrous ion and H2O2 dosage. It is remarkable that organic compounds were completely mineralized by Fenton oxidation, of which removal efficiency is superior to that of UV/H2O2. Nevertheless, it makes slight difference between Fenton oxidation and UV/Fenton oxidation. According to the spectra identified by gas chromatograph/mass spectrometer (GC/MS), it is proposed that oxidative degradation of DNT isomers leads to o-, m-, p-mononitrotoluene (MNT) and 1,3-dinitrobenzene respectively. Besides, the oxidation of 2,4,6-TNT gives the 1,3,5-trinitrobenzene intermediate. Apparently, Fenton oxidation is promising for purification of spent acid industrially.     

Kinetic behavior of anti-inflammatory drug ibuprofen in aqueous medium during its degradation by electrochemical advanced oxidation

The electrochemical abatement of the drug ibuprofen (2-(4-isobutylphenyl)propionic acid) from aqueous solution has been carried out by anodic oxidation. The electrolyses have been performed at constant current using a small, undivided cell equipped with a Pt or thin-film boron-doped diamond (BDD) anode and a carbon-felt cathode. The results have shown that ibuprofen has been destroyed under all the conditions tested, following pseudo-first-order kinetics; however, BDD enables higher removal rates than Pt, because the former produces greater quantity of ^?OH. Using BDD anode, the pseudo-first-order rate constant increased with applied current and when NaCl replaced Na₂SO₄ as supporting electrolyte, while it is almost unaffected by ibuprofen concentration. Mineralization of ibuprofen aqueous solutions was followed by total organic carbon (TOC) measurements. After 8 h of electrolysis, TOC removal varied from 91 % to 96 % applying a current in the range of 50–500 mA. The reaction by-products were quantified by chromatographic techniques, and in particular, aliphatic acids (oxalic, glyoxylic, formic, acetic, and pyruvic) have been the main intermediates formed during the electrolyses. The absolute rate constant for the oxidative degradation of ibuprofen have also been determined, by competition kinetic method, as 6.41?×?10⁹ M^?1?s^?1.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Electro-oxidation of the dye azure B: kinetics,mechanism, and by-products

In this work, the electrochemical degradation of the dye azure B in aqueous solutions was studied by electrochemical advanced oxidation processes (EAOPs), electro-Fenton, and anodic oxidation processes, using Pt/carbon-felt and boron-doped diamond (BDD)/carbon-felt cells with H₂O₂ electrogeneration. The higher oxidation power of the electro-Fenton (EF) process using BDD anode was demonstrated. The oxidative degradation of azure B by the electrochemically generated hydroxyl radicals (^?OH) follows a pseudo-first-order kinetics. The apparent rate constants of the oxidation of azure B by ^?OH were measured according to pseudo-first-order kinetic model. The absolute rate constant of azure B hydroxylation reaction was determined by competition kinetics method and found to be 1.19?×?10⁹ M^?1 s^?1. It was found that the electrochemical degradation of the dye leads to the formation of aromatic by-products which are then oxidized to aliphatic carboxylic acids before their almost mineralization to CO₂ and inorganic ions (sulfate, nitrate, and ammonium). The evolution of the TOC removal and time course of short-chain carboxylic acids during treatment were also investigated.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Fenton-超声联合处理金刚烷胺制药废水

近年来,流感常用药盐酸金刚烷胺的产量不断增大,然而,其生产过程中产生的废水由于得不到有效处理,引起较大污染。以盐酸金刚烷胺生产过程中产生的胺化废水和溴化废水为原水,利用Fenton-超声联合工艺进行处理,主要研究反应时间、初始pH、H2O2投加量和H2O2/Fe2+的投加比和声能密度等操作条件对于金刚烷胺制药废水处理效果的影响。实验结果表明,优化处理条件下,Fenton-超声联合工艺对金刚烷胺制药废水中TOC去除效果最高达到65.6%。超声和Fenton的联合产生了良好的协同效果,Fenton-超声联合工艺对金刚烷胺制药废水的处理效果比单独超声和单独Fenton处理效果之和高18%,大大提高了废水中有机物的去除效果。     

Performance evaluation of a continuous flow photocatalytic reactor for wastewater treatment

A novel photocatalytic reactor for wastewater treatment was designed and constructed. The main part of the reactor was an aluminum tube in which 12 stainless steel circular baffles and four quartz tube were placed inside of the reactor like shell and tube heat exchangers. Four UV–C lamps were housed within the space of the quartz tubes. Surface of the baffles was coated with TiO₂. A simple method was employed for TiO₂ immobilization, while the characterization of the supported photocatalyst was based on the results obtained through performing some common analytical methods such as X-ray diffraction (XRD), scanning electron microscope (SEM), and BET. Phenol was selected as a model pollutant. A solution of a known initial concentration (20, 60, and 100 ppmv) was introduced to the reactor. The reactor also has a recycle flow to make turbulent flow inside of the reactor. The selected recycle flow rate was 7?×?10^?5 m³.s^?1, while the flow rate of feed was 2.53?×?10^?7, 7.56?×?10^?7, and 1.26?×?10^?6 m³.s^?1, respectively. To evaluate performance of the reactor, response surface methodology was employed. A four-factor three-level Box–Behnken design was developed to evaluate the reactor performance for degradation of phenol. Effects of phenol inlet concentration (20–100 ppmv), pH (3–9), liquid flow rate (2.53?×?10^?7?1.26?×?10^?6 m³.s^?1), and TiO₂ loading (8.8–17.6 g.m^?2) were analyzed with this method. The adjusted R ² value (0.9936) was in close agreement with that of corresponding R ² value (0.9961). The maximum predicted degradation of phenol was 75.50 % at the optimum processing conditions (initial phenol concentration of 20 ppmv, pH?～?6.41, and flow rate of 2.53?×?10^?7 m³.s^?1 and catalyst loading of 17.6 g.m^?2). Experimental degradation of phenol determined at the optimum conditions was 73.7 %. XRD patterns and SEM images at the optimum conditions revealed that crystal size is approximately 25 nm and TiO₂ nanoparticles with visible agglomerates distribute densely and uniformly over the surface of stainless steel substrate. BET specific surface area of immobilized TiO₂ was 47.2 and 45.8 m² g^?1 before and after the experiments, respectively. Reduction in TOC content, after steady state condition, showed that maximum phenol decomposition occurred at neutral condition (pH?～?6). Figure

The schematic view of the experimental set-up     

Fe(III)–EDDS complex in Fenton and photo-Fenton processes: from the radical formation to the degradation of a target compound

The present work compares the efficiency of homogenous Fenton and photo-Fenton processes in the presence of Fe(III)–EDDS complex under different experimental conditions. 4-tert-Butylphenol (4-t-BP), which is one of the endocrine disrupting chemicals, was used as a model pollutant to investigate the Fenton and photo-Fenton application. The efficiency of homogenous photo-Fenton process was significantly much higher than homogenous Fenton process, which is due to the rapid formation of Fe²⁺ under UV irradiation of the iron complex and the photochemical formation of HO^? from the photolysis of the complex Fe(III)–EDDS. Through the degradation of 4-t-BP, the effect of Fe(III)–EDDS concentration, H₂O₂ concentration, pH, and oxygen was investigated in both processes. Such trend was also correlated with pH calculating the polychromatic Fe²⁺ quantum yield formation at pH 4.0, 6.0, and 8.6. The results showed that at high Fe(III)–EDDS and H₂O₂ concentrations, a negative effect was found. By the way, the Fenton process was found to be enhanced at basic pH. These results can be very useful for the use and optimization of such iron complex in water treatment process as function of different physico-chemical conditions.     

Environmental photochemical fate of pesticides ametryn and imidacloprid in surface water (Paranapanema River,São Paulo,Brazil)

In addition to direct photolysis studies, in this work the second-order reaction rate constants of pesticides imidacloprid (IMD) and ametryn (AMT) with hydroxyl radicals (HO^●), singlet oxygen (¹O₂), and triplet excited states of chromophoric dissolved organic matter (³CDOM^*) were determined by kinetic competition under sunlight. IMD and AMT exhibited low photolysis quantum yields: (1.23?±?0.07)?×?10^–2 and (7.99?±?1.61)?×?10^–3 mol Einstein^?1, respectively. In contrast, reactions with HO^● radicals and ³CDOM* dominate their degradation, with ¹O₂ exhibiting rates three to five orders of magnitude lower. The values of k_IMD,HO● and k_AMT,HO● were (3.51?±?0.06)?×?10⁹ and (4.97?±?0.37)?×?10⁹ L mol^?1 s^?1, respectively, while different rate constants were obtained using anthraquinone-2-sulfonate (AQ2S) or 4-carboxybenzophenone (CBBP) as CDOM proxies. For IMD this difference was significant, with k_IMD,3AQ2S*?=?(1.02?±?0.08)?×?10⁹ L mol^?1 s^?1 and k_IMD,3CBBP*?=?(3.17?±?0.14)?×?10⁸ L mol^?1 s^?1; on the contrary, the values found for AMT are close, k_AMT,3AQ2S*?=?(8.13?±?0.35)?×?10⁸ L mol^?1 s^?1 and k_AMT,3CBBP*?=?(7.75?±?0.80)?×?10⁸ L mol^?1 s^?1. Based on these results, mathematical simulations performed with the APEX model for typical levels of water constituents (NO₃^?, NO₂^?, CO₃^2?, TOC, pH) indicate that the half-lives of these pesticides should vary between 24.1 and 18.8 days in the waters of the Paranapanema River (São Paulo, Brazil), which can therefore be impacted by intensive agricultural activity in the region.

     

FTIR gas-phase kinetic study on the reactions of some acrylate esters with OH radicals and Cl atoms

Acrylate esters are α,β-unsaturated esters that contain vinyl groups directly attached to the carbonyl carbon. These compounds are widely used in the production of plastics and resins. Atmospheric degradation processes of these compounds are currently not well understood. The kinetics of the gas phase reactions of OH radicals with methyl 3-methylacrylate and methyl 3,3-dimethylacrylate were determined using the relative rate technique in a 50 L Pyrex photoreactor using in situ FTIR spectroscopy at room temperature (298?±?2 K) and atmospheric pressure (708?±?8 Torr) with air as the bath gas. Rate coefficients obtained were (in units cm³ molecule^?1 s^?1): (3.27?±?0.33)?×?10^?11 and (4.43?±?0.42)?×?10^?11, for CH₃CH═CHC(O)OCH₃ and (CH₃)₂CH═CHC(O)OCH_3, respectively. The same technique was used to study the gas phase reactions of hexyl acrylate and ethyl hexyl acrylate with OH radicals and Cl atoms. In the experiments with Cl, N₂ and air were used as the bath gases. The following rate coefficients were obtained (in cm³ molecule^?1 s^?1): k₃ (CH₂═CHC(O)O(CH₂)₅CH₃?+?Cl)?=?(3.31?±?0.31)?×?10^?10, k₄(CH₂═CHC(O)OCH₂CH(CH₂CH₃)(CH₂)₃CH₃?+?Cl)?=?(3.46?±?0.31)?×?10^?10, k₅(CH₂═CHC(O)O(CH₂)₅CH₃?+?OH)?=?(2.28?±?0.23)?×?10^?11, and k₆(CH₂═CHC(O)OCH₂CH(CH₂CH₃)(CH₂)₃CH₃?+?OH)?=?(2.74?±?0.26)?×?10^?11. The reactivity increased with the number of methyl substituents on the double bond and with the chain length of the alkyl group in –C(O)OR. Estimations of the atmospheric lifetimes clearly indicate that the dominant atmospheric loss process for these compounds is their daytime reaction with the hydroxyl radical. In coastal areas and in some polluted environments, Cl atom-initiated degradation of these compounds can be significant, if not dominant. Maximum Incremental Reactivity (MIR) index and global warming potential (GWP) were also calculated, and it was concluded that these compounds have significant MIR values, but they do not influence global warming.