Spectrophotometric Determination of Atmospheric Acidity by means of the Displacement of the Equilibrium of Acid-Base Indicators

A method is described for determining acidity by means of the spectrophotometric determination of the displacement of the equilibrium of açid-base indicators. The method is simple, sensitive and free of known interferences. There is no dependence on costly or sophisticated equipment and the results obtained are reliable and reproducible.     

污泥淤砂分离器对分离分流污泥性质的影响

为解决我国很多城镇污水厂活性污泥的MLVSS/MLSS普遍偏低,污泥中泥沙淤积严重的问题,根据水力旋流器的分离原理,开发了污泥淤砂分离器,实现污泥中生物基质和淤砂的分离分流,研究污泥淤砂分离器主要结构参数排口比(底流口直径/溢流管直径)对分离分流污泥性质的影响。实验结果表明,排口比为0.4时,污泥经过污泥淤砂分离器后,得到的底流污泥MLVSS/MLSS比原污泥减小了34%,溢流污泥MLVSS/MLSS增大了16.8%,污泥中的生物基质富集在溢流污泥中,淤砂富集在底流污泥中;底流污泥浓度MLSS比原污泥增加了2.6倍,底流污泥SVI和CST分别减小了68%和70%,底流污泥浓缩效果明显,沉降性能和脱水性能大幅提高,有利于底流污泥的处理处置;进一步减小排口比,底流污泥浓缩效果、沉降性能和脱水性能均进一步提高。     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

The environmental significance of surface films II. Enhanced partitioning of Lindane in thin films of octanol on the surface of water

The log of the partition coefficient for Lindane between octanol and water at 22°C is 3.2; it is 3.9 if the octanol is in the form of a lens floating on the water, and it is 4.5 between an octanol monolayer and the underlying water.     

Thermodynamics of binding of cadmium to bovine serum albumin

The binding isotherm of Cd2+ ion to bovine serum albumin (BSA) has been investigated by microcalorimetry at 310.15 K and pH 7.0. The thermodynamic parameters of the binding reaction have been determined, and the stoichiometry of the complex is 2:1, indicating that there exist two identical binding sites of BSA with Cd2+ ion. The value of deltarHthetam is -28.4+/-1.7 kJ mol(-1), the free energy of binding deltarGthetam is -25.2 kJ mol(-1), and the entropy of binding deltarSthetam is -10.3 J mol(-1) K(-1). The negative deltarHthetam and deltarSthetam values are observed for the binding reaction of Cd2+ ion and BSA, suggesting that the binding reaction is mainly enthalpy-driven and the entropy is unfavorable for it.     

Assessment of the sustainability of technology by means of a thermodynamically based life cycle analysis

Life cycle analysis is one of the tools in the assessment of the sustainability of technological options. It takes into account all effects on the ecosystem and the population which may endanger the possibilities of current and future generations. However, the main bottleneck in current LCA methodologies is the balancing of different effects, being all quantified on different scales. In this work, a methodology is proposed, which allows one to quantify different effects of the production, consumption and disposal of goods, and services on a single scale. The basis of the methodology is the second law of thermodynamics. All production, consumption and disposal processes affecting the ecosystem and the population, are quantified in terms of loss of exergy. The exergy content of a material is the maximum amount of energy which can be transformed into work at given environmental conditions. Next to the elaboration of the methodology, the new approach is illustrated by examples of the production of synthetic organic polymers, inorganic building insulation materials and different waste gas treatment options.     

The prediction of the numbers of violations of standards and the frequency of air pollution episodes using extreme value theory

Extreme value theory is discussed in a manner suitable for scientists working in the air pollution area. The method of application of the theory is described by means of an example analysis on an ozone data set and the theory is applied to several data sets collected in Brisbane, Queensland, Australia. The theory is used to predict the number of violations of WHO and U.S. standards expected in the year following data collection. Comparison of these predictions with the relevant observations shows that the theory does quite well. Ways of using extreme value theory as an air quality management tool are suggested.     

Environmental Persistence of Chemicals

- DOI: http://dx.doi.org/10.1065/espr2006.01.008 Background The hazard criterion of persistence as it applies to chemicals in the environment is reviewed and discussed. This quantity can not be measured directly in the environment, thus it must be estimated using models that synthesise information on chemical half-lives and partitioning properties, the nature of the environment and how the chemical is released into the environment. Main Features It is suggested that the preferred criterion is the average residence time of the chemical in the environment, i.e. conceptually the sum of the life-times of all molecules (attributable only to losses by degrading reactions) divided by the number of molecules. If all chemical fate processes are first order, this persistence is independent of the quantity of chemical introduced and whether introduction is steady- or unsteady-state in nature. It is shown that in a multimedia environment persistence is affected not only by degradation kinetics, but also by mode-of-entry and partitioning. For screening level purposes a Level II equilibrium model may be adequate but a Level III model is generally preferable for estimating the average persistence. If a distribution of persistences is required a dynamic Level IV model must be used. Discussion The implications for regulating chemicals on the basis of persistence are discussed. Conclusion It is concluded that the preferred strategy is to use Level II, III, and IV models and that the use of only degradation kinetics or media-specific half-lives can be misleading and uneconomical.     

垃圾焚烧炉炉膛温度的影响因素

垃圾焚烧过程的不稳定会导致大量有害物质的生成,为确保垃圾的清洁燃烧需要将炉膛温度控制在850℃以上,为此测试了焚烧炉运行的主要可控参数对炉膛温度的影响。结果表明,垃圾堆放位置在垃圾池深3～8 m处,并经过6 d以上发酵脱水后适合焚烧;炉膛温度随给料量、一次风率和一次风温增加而增大,随过量空气系数增加而降低,其中给料量宜控制在95%～110%之间;当过量空气系数为1.6、一次风率为90%、一次风温为260℃、给料量为100%时炉膛温度达901℃。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

不同类型机动车尾气中芳香烃化合物含量分析

首次对北京市9种车辆、5种燃料在不同工况下排放芳香烃化合物的特征．进行了定量研究。结果表明,车型、燃料、净化器及工况等因素对排放量产生影响,电喷车比化油器车芳香烃化合物排放量低;汽油车排放量最高,柴油车其次,LPG及CNG车排放量最低;使用净化器可以降低芳香烃排放量;不同工况对排放量的影响随车型,燃料类型的不同而不同。     

Considerations of uncertainty in setting critical loads of acidity of soils: the role of weathering rate determination

The concept of critical loads has been generally accepted throughout Europe, and increasingly in Asian countries and the rest of the world, as providing the data which forms the basis for international negotiations on abatement strategies for emissions of acidifying pollutants. Central to the determination of quantitative critical loads of acidity for forests (and other ecosystems) is the rate at which the minerals in the soil weather or dissolve. Seven methods for determining these rates on a regional basis for the production of critical load maps have been suggested by the official bodies which are responsible for co-ordinating the European critical load mapping efforts. These methods are largely correlations which require a knowledge of the soil parent material and/or the soil mineralogy. The purpose of this paper is to review these weathering rate calculation methods and to assess whether it is currently possible to calculate numerically accurate critical loads for the production of regional critical load maps. A consideration of the data used to generate these methods and comparisons of the weathering rates calculated using various methods leads to the conclusion that at present it is not. Further work is needed to develop and maintain the initial credibility of critical loads both scientifically and as an aid to policy decisions.     

Determination of sources of atmospheric aerosol in Copenhagen based on receptor models

A statistical analysis is presented of atmospheric aerosol element composition data collected at five monitoring stations in Copenhagen in 1983. The objective is to identify sources of air pollution, to estimate the variation of total suspended particles (TSP) for the different sources and to calculate the annual average source contribution to TSP. The basis for analysis is the chemical mass balance equations. Factor analysis methods are used to identify major sources of pollution and the contribution from each of the sources to the variation in TSP is estimated by an additional multiple regression. Finally, the influence of serial correlations between daily element contributions is discussed and it is stressed that the result of the analysis is not seriously affected by these correlations.     

活性炭纤维净化印刷过程产生的VOCs废气

介绍了应用局部排气的方法,收集印刷过程的挥发性有机化合物(VOCs)废气,应用活性炭纤维(ACF)吸附脱附有机废气回收净化装置,进行印刷厂VOCs废气的回收与治理,详细描述了印刷车间VOCs废气的收集与处理工艺过程及其效果.测试结果表明,应用此工艺和设备可以有效地进行印刷过程大风量的VOCs废气的回收和治理.     

采用杂多酸化合物溶液同时脱硫脱氮的实验研究

本文对液相催化氧化脱硫脱氮的新方法进行了研究 ,在鼓泡反应发生器内进行了液相催化氧化脱硫脱氮的实验。采用钼硅酸溶液及其还原产物脱除烟气中的SO2 和NOX,分别就吸收液的浓度、pH值、温度、停留时间等因素对SO2 和NOX 去除效率的影响及其变化规律进行了研究。实验结果表明 ,钼硅酸能十分有效地吸收SO2 ,将SO2 氧化成H2 SO4,并使杂多酸还原为杂多蓝。随后又被用于去除NOX,把NOX 还原成N2 ,蓝色溶液再次被氧化成为黄色溶液     

Analysis of stability of silica nano-particle-laden microbubble dispersion

Microbubbles are small gas-filled bubbles which have wide application in various industries. The stability of microbubble is of primary concern for the application of microbubble. In this research, the stability of microbubble dispersion generated using CTAB surfactant is analyzed by drainage mechanism. The stability of microbubble dispersion is studied on the basis of the half-life of microbubble dispersion. Microbubble dispersion gas fraction and apparent rise velocity of interface of microbubble dispersion are also calculated. The size of microbubble is estimated from the apparent rise velocity of interface of microbubble dispersion. Further, silica nano-particles are added to the surfactants to study their effect on the stability of microbubble dispersion. The observed results clearly indicate that the stability of microbubble dispersion is significantly affected by the surfactant concentration and the weight of silica nano-particle in the liquid. Similar results were observed for the apparent rise velocity of interface and bubble size of dispersion. The present work may be beneficial for the application of microbubble in various chemical and biochemical industries and scientific community.

     

Analysis of chemical and physical effects of ultraviolet bulbs on cooking emissions

There is a growing recognition of the risks to health, fire hazard, and air quality from cooking emissions. Recent research has identified what is emitted when foods are cooked. Some of the emitted mass is captured in the exhaust system. The balance is expelled into the atmosphere. The outlet of the exhaust system is a demarcation point-upstream the captured mass is the operator or building owner's concern, whereas downstream into the atmosphere, it affects air quality. Building codes have long required operators to deal with the upstream section. More recently, regulations are being placed on what kitchens can emit to the atmosphere. The industry is responding to this challenge with product innovations. Recently gained understanding of cooking emissions supports much of the innovation-but not all. This paper evaluates the purported benefit of adding better filtration and ultraviolet C (UVC) bulbs in kitchen hoods. A "UV hood" claims a two-step process to reduce emissions: better filters capture more emitted mass, and UVC photons and ozone drive photo-decomposition and oxidation reactions of some of the remaining greasy constituents. Adding UV to a hood at least doubles the cost compared to an equivalent non-UV hood. There is evidence that UV hoods do reduce some emissions. The essential question is whether improved performance is due to UV or relatively inexpensive, improved filters. Experimentation exposed an oleic acid aerosol, representative of cooking emissions, to UVC energy and ozone at higher concentrations and for longer exposure times than can occur in a UV hood. Particle-size and chemical changes were measured on samples collected with UV bulbs off and on. Results strongly indicate little change is happening and most emission reductions are caused by better filtration and not UV. The conclusion is that UV hoods fall short of claimed performance, and unreacted ozone may increase air pollution.     

Assessment of bioconcentration and secondary poisoning of surfactants

The relevance of the bioconcentration behaviour of surfactants for the secondary poisoning assessment and for the risk characterisation in the bird and mammalian food chain has been investigated. The approach used is described in the recently revised EU Technical Guidance Document for the Risk Assessment of Substances. The results demonstrate that, based on experimentally derived bioconcentration factors, environmental concentrations and effects in animals, there is a clear level of safety for both linear alkylbenzene sulphonate (LAS) and alcohol ethoxylates (AE), the most important surfactants by volume. To assess other surfactants used in detergents, a bioconcentration factor that would need to be attained for secondary poisoning to be of concern has been estimated from predicted environmental concentrations and known long-term effects data in animals. Based on the known structural similarity of these surfactants to LAS and AE and the ubiquitous nature of the enzymatic systems that are present in biotransformation processes in organisms, it is concluded that bioconcentration of these surfactants to these levels is highly unlikely. Therefore the potential for secondary poisoning effects of these surfactants is extremely low.     

Status of Control of Motor Vehicle Emissions in California

The State of California, because of an acute air pollution problem has been forced to move ahead on a pioneer basis to control motor vehicle emissions. The Golden State’s program, as put into operation by the Motor Vehicle Pollution Control Board, is discussed in detail. Inspection-installation stations, enforcement and legal requirements relating to crankcase control devices and other facets of the program are presented. Of particular importance is the experience gained by the Board in requiring devices on all new vehicles registered in California and its used vehicle program, affecting vehicles back to the 1950 model year. Recent developments in exhaust control, anticipated installation requirements, and scheduling, as well as an indication of staff long-term planning is also outlined. California’s program is based on the principle that the motor vehicle must be controlled and that sewage no longer can be dumped into the air, if the public health is to be preserved.