Correlation of PCDD/PCDF and CO values in a MSW incinerator--indication of memory effects in the high temperature/cooling section

The correlation of PCDD/PCDF levels with the CO emissions in a full-scale municipal waste incinerator was assessed during a four-week measurement effort. PCDD/PCDF concentrations in fly ashes-containing more than 99% of the total PCDD/PCDF burden of the fluidized bed incinerator (FBI)-were measured and compared with the emitted CO concentrations. The CO concentration during the sampling time showed no significant correlation to the PCDD/ PCDF amount in fly ash (R2 = 0.078). However, a comparison of the time integrated CO concentration several hours before sampling lead to a correlation with the PCDD/PCDF burden. Maximum correlation was found for the time integrated CO values of 3 and 4 h before sampling (R2 = 0.467 and R2 = 0.457 respectively). This indicates a memory effect in the high temperature cooling section of several hours. Possible mechanisms leading to the memory effect are discussed. The correlation of PCDD/PCDF with CO concentration demonstrate that the combustion conditions play an important role for PCDD/PCDF formation in FBIs. However the variability in the correlation of CO to PCDD/PCDF levels show that other factors have a significant influence on PCDD/PCDF formation.     

CuCl2-catalyzed PCDD/F formation and congener patterns from phenols

Homologue and isomer patterns of polychlorinated dibenzo-p-dioxin (PCDD) and polychlorinated dibenzofuran (PCDF) in CuCl2-catalyzed formation were studied in an isothermal flow reactor using a distribution of 20 phenols as measured in municipal waste incinerator (MWI) exhaust gases. A mixture of 20 phenols was synthesized and used as reactants for this study because phenols are known to be key precursors in the formation of PCDD/F. Experiments were conducted at 400 degrees C. The 92% of nitrogen (N2) and 8% of oxygen (O2) were used as a carrier gas. PCDD/F homologue and isomer patterns with dibenzo-p-dioxin (DD) and dibenzofuran (DF) were obtained from a mixture of 20 phenols. DF+PCDF formation was favored over DD+PCDD formation. The major homologue groups formed were non-chlorinated DD and DF, and PCDD/F homologue fraction decreased with the degree of chlorination. PCDD/F homologue and isomer distributions were almost constant. Phenol and lower chlorinated phenols present in high amount played an important role in PCDD/F congener distributions. The results presented here can be used as characteristics or fingerprints for homologue and isomer patterns of PCDD/F formation attribution in CuCl2-catalyzed reaction from phenols.     

PCDD/PCDF,chlorinated pesticides and PAH in Chinese teas

Four samples of Chinese tea (two green teas, and two brick teas) were analyzed for their concentrations of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF), chlorinated pesticides and PAH. The infusions prepared from these teas were also analyzed for PCDD/PCDF. The levels of DDT and its metabolites in tea leaves were within the safety limit of 0.2 mg/kg. Rather high levels of total PAH were obtained in brick tea (1048–1162 mg/kg), when compared with green tea (497–517 mg/kg). In terms of PCDD/PCDF, the concentrations of green tea and brick tea differed by a factor of 16, while the concentrations of all infusions were within a factor of 2. The dioxin concentrations in green tea leaves can be explained through uptake of atmospheric PCDD/PCDF. The higher concentrations in the brick tea leaves are due the longer exposure time, and to certain extent, the use of old leaves, branches and roots when making the tea, and additional components such as soil particulates through contamination. Certain Chinese populations drinking a large amount of brick tea (>3 l per day) indicated that individuals of these populations consume more tea than Europeans or North Americans result in a comparably higher intake of PCDD/PCDF. Tea consumption can attribute to up to 10% of the TDI recommended by WHO (only PCDD/PCDF considered, no PCB analyzed).     

Effects of combustion and operating conditions on PCDD/PCDF emissions from power boilers burning salt-laden wood waste

This paper discusses the effects of combustion conditions on PCDD/PCDF emissions from pulp and paper power boilers burning salt-laden wood waste. We found no correlation between PCDD/PCDF emissions and carbon monoxide emissions. A good correlation was, however, observed between PCDD/PCDF emissions and the concentration of stack polynuclear aromatic hydrocarbons (PAHs) in the absence of TDF addition. Thus, poor combustion conditions responsible for the formation of products of incomplete combustion (PICs), such as PAHs and PCDD/PCDF precursors, increase PCDD/PCDF emissions. PAH concentrations increased with higher boiler load and/or low oxygen concentrations at the boiler exit, probably because of lower available residence times and insufficient excess air. Our findings are consistent with the current understanding that high ash carbon content generally favours heterogeneous reactions leading to either de novo synthesis of PCDD/PCDFs or their direct formation from precursors. We also found that, in grate-fired boilers, a linear increase in the grate/lower furnace temperature produces an exponential decrease in PCDD/PCDF emissions. Although the extent of this effect appears to be mill-specific, particularly at low temperatures, the results indicate that increasing the combustion temperature may decrease PCDD/PCDF emissions. It must be noted, however, that there are other variables, such as elevated ESP and stack temperatures, a high hog salt content, the presence of large amounts of PICs and a high Cl/S ratio, which contribute to higher PCDD/PCDFs emissions. Therefore, higher combustion temperatures, by themselves, will not necessarily result in low PCDD/PCDFs emissions.     

Effects of sulfur dioxide, hydrogen peroxide and sulfuric acid on the de novo synthesis of PCDD/F and PCB under model laboratory conditions

In a laboratory model system consisting of fly ash from municipal waste incinerator, CuCl2 x 2H2O, NaCl and activated carbon in N2 + 10% O2 atmosphere, the de novo synthetic reactions of formation of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), and polychlorinated biphenyls (PCBs) were studied under laboratory conditions in the presence of sulfur dioxide, hydrogen peroxide, and sulfuric acid. It has been found that the formation of PCDD is suppressed by sulfur dioxide more efficiently than the formation of PCDF. A similar effect has also been observed in the presence of hydrogen peroxide. The formation of PCDF is strongly suppressed in the presence of sulfuric acid. On the basis of the experimental results and thermodynamic calculations, the following mechanisms are proposed and discussed: oxidative destruction of PCDD and PCDF oxygen rings, conversion of cupric chloride and possibly also cupric oxide into the non-reactive sulfate, and the Deacon oxychlorination processes catalyzed by cupric chloride.     

Occurrence, possible sources, and temporal trends of polychlorinated dibenzo-p-dioxins and dibenzofurans in water and sediment from the lower Yangtze River basin, Jiangsu and Shanghai areas of Eastern China

The concentrations, compositional profiles, and possible sources of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) in water column and surface sediment samples from the lower reaches of the Yangtze River were investigated, and the potential risks posed by these chemicals were evaluated. Concentrations of the 17 2,3,7,8-substituted PCDD/PCDF in the water and sediment samples ranged from 0.45 to 10.0 pg TEQ/L (mean 2.34 pg TEQ/L) and from 0.31 to 51 pg TEQ/g dw (mean 5.25 pg TEQ/g dw), respectively. Water and sediments from the Nanjing–Nantong sections of the Yangtze River were found to have elevated PCDD/PCDF levels, and the PCDD/PCDF TEQ concentrations in 13 sediment samples exceeded the probable effect levels (PEL), above which adverse biological effects are likely. Multivariate statistical analysis indicated that the principal PCDD/PCDF contamination source for the water and sediment was the production and use of pentachlorophenol (PCP) or sodium pentachlorophenate (PCP-Na). PCDD/PCDF concentrations were stable over time near the Yangtze River Estuary but had increased sharply in recent decades in the Nanjing–Nantong section, which will have been related to the growth in industrial activities and other anthropogenic PCDD/PCDF sources. Total organic carbon (TOC) and PCDD/PCDF concentrations correlated significantly (R?=?0.474, P?<?0.01), suggesting that TOC plays an important role in the transport and re-distribution of PCDD/PCDF in the Yangtze River basin.     

Experimental and statistical determination of indicator parameters for the evaluation of fly ash and boiler ash PCDD/PCDF concentration from municipal solid waste incinerators

On-line detectable indicator parameters in the flue gas of municipal solid waste incinerators (MSWI) such as chlorinated benzenes (PCBz) are well known surrogate compounds for gas-phase PCDD/PCDF concentration. In the here presented work derivation of indicators is broadened to the detection of fly and boiler ash fractions with increased PCDD/PCDF content. Subsequently these fractions could be subject to further treatment such as recirculation in the combustion chamber to destroy their PCDD/PCDF and other organic pollutants' content. Aim of this work was to detect suitable on-line detectable indicator parameters in the gas phase, which are well correlated to PCDD/PCDF concentration in the solid residues. For this, solid residues and gas-phase samples were taken at three MSWI plants in Bavaria. Analysis of the ash content from different plants yielded a broad variation range of PCDD/PCDF concentrations especially after disturbed combustion conditions. Even during normal operation conditions significantly increased PCDD/PCDF concentrations may occur after unanticipated disturbances. Statistical evaluation of gas phase and ash measurements was carried out by means of principal component analysis, uni- and multivariate correlation analysis. Surprisingly, well known indicators for gas-phase PCDD/PCDF concentration such as polychlorinated benzenes and phenols proved to be insufficiently correlated to PCDD/PCDF content of the solid residues. Moreover, no single parameter alone was found appropriate to describe the PCDD/PCDF content of fly and boiler ashes. On the other hand, multivariate fitting of three or four parameters yielded convenient correlation coefficients of at least r=0.8 for every investigated case. Thereby, comprehension of plant operation parameters such as temperatures and air flow alongside concentrations of inorganic compounds in the gas phase (HCl, CO, SO2, NOx) gave the best results. However, the suitable set of parameters suited best for estimation of PCDD/PCDF concentration in solid residues has to be derived anew for each individual plant and type of ash.     

Formation and destruction of PCDD/F inside a grate furnace

Formation and destruction of polychlorinated dibenzo-p-dioxins and dibenzofurans PCDD/F during the combustion process was investigated experimentally in a pilot plant. All important process steps like the burnout of the fuel bed on the grate, the burnout of the flue gas inside the combustion chamber, the heat recovery in a boiler as well as influences of the fuel composition are described in detail.

High concentrations especially of PCDF are formed during the burnout of the fuel bed. The formation reaction is mainly influenced by the fuel composition and the burnout characteristic of the fuel bed. Fuels with low chlorine and low metal content (Cu) result only in negligible concentrations of PCDD/F.

Under stable combustion conditions characterized by an excellent flue gas burnout PCDD/F will almost be completely destroyed already inside the combustion chamber. “Cold strands” of unburned flue gas (high CO concentrations) caused by disturbed combustion conditions will result in high concentrations of PCDD and especially of PCDF in the raw gas.

A second place of PCDD/F formation is the well-known boiler section. Here fly ash deposits containing residual carbon (mainly soot particles) are the source for the formation reaction. Under stationary effective combustion conditions, they are dominant for PCDD/F concentrations in the raw gas over a very long period of time.

Stationary efficient flue gas burnout (especially soot) together with effective boiler cleaning will guaranty low concentrations of PCDD/F in the flue gas in front of the flue gas cleaning system.     

PCDD/PCDF emissions from small firing systems in households

This report presents results of emission measurements of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in the flue gas of seven oil, nine gas, and two wood firing systems under laboratory conditions. The burn rate of the combustion was in the range of the rated useful heat output. Two additional test series varied the amount of combustion air and thus the heat output. The PCDD/PCDF emissions for oil- and gas-fired boilers are in the range of 0.0020-0.0142 ng I-TEQ/m3 (referring to 3% O2 in the dry flue gas). No correlation between the combustion technique and the PCDD/PCDF emissions could be established. In the tests with the wood-fired furnaces PCDD/PCDF concentrations in the flue gas ranging from 0.014 to 0.076 ng I-TEQ/m3 (referring to 13% O2 in the dry flue gas) were found. A significant correlation between the firing rate of the heating insert and the measured PCDD/PCDF concentrations was found. On examination of three typical 2,3,7,8-CDD/CDF congener profiles, a comparable pattern could be observed with natural gas and light fuel oil. The congener distribution for wood combustion is considerably different.     

Effects of oxygen on formation of PCB and PCDD/F on extracted fly ash in the presence of carbon and cupric salt

The effect of oxygen-nitrogen atmosphere (N2 + 10%O2, N2 + 1%O2 and 99.999% N2) on the formation of PCB, PCDD and PCDF by the de novo synthetic reactions in the system consisting of extracted fly ash (from municipal waste incinerators--MWI), activated carbon, CuCl2 x 2H2O and NaCl at 340 degrees C was studied. The content of PCDD/F for systems with 10%O2, 1%O2 and 99.999% N2 was decreasing and corresponded to 17,304, 5544, and 1437 ng/sample. In all studied systems the isomer OCDD/F was prevailing. The content of PCBs in the same system was also decreasing from 1214 to 166 ng/g. Formation of nonortho PCB was relatively high compared to the system where only nitrogen was present. The possible mechanism of formation is outlined.     

Kinetics of carbon degradation and PCDD/PCDF formation on MSWI fly ash

The native carbon oxidation and PolyChloroDibenzo-p-Dioxins and PolyChloroDibenzoFurans, PCDD/F, formation were simultaneously studied at different temperatures (230-350 degrees C) and times (0-1440 min) in order to establish a direct correlation between the disappearance of the reagent and the formation of the products. The kinetic runs were conducted in an experimental set up where conditions were chosen to gain information on the role of fly ash deposits in cold zones of municipal solid waste incinerators in PCDD/F formation reaction. The carbon oxidation measured as the decrease of total organic carbon of fly ash was in agreement with the carbon evolved as sum of CO and CO(2). The carbon mass balance indicated an increase in the efficiency of carbon conversion in CO and CO(2) with temperature. The CO and CO(2) formation was the result of two parallel pseudo first order reactions thus giving significant information about the reaction mechanism. PCDD/F formation as a function of temperature showed that the maximum formation was achieved in a narrow range around 280 degrees C; the time effect at 280 degrees C was a progressive formation increase at least up to 900 min. The PCDF:PCDD molar ratio increased with temperature and time, and the most abundant homologues were HxCDD, HpCDD, OCDD for PCDD, and HxCDF, HpCDF within PCDF. These experimental results supported the hypothesis that the formation mechanism was the de novo synthesis.     

Temporal trends and spatial distribution of PCDD, PCDF, and PCB in pine and spruce shoots

In Germany, there is a lack of consistent and comparable data for the time dependent behaviour and spatial distribution of dioxin-like and indicator PCB in ambient air, deposition and plants. The aim of this study was to improve the data on PCDD/PCDF, dioxin-like PCB and non dioxin-like PCB in spruce and pine shoots from different locations and years by retrospective monitoring. The survey was conducted with archived samples of one-year old spruce shoots (Picea abies) and pine shoots (Pinus sylvestris) from the German environmental specimen bank. Two sets of samples from locations in urbanized areas in western and eastern Germany (Warndt and Duebener Heide Mitte, respectively) were investigated as time series. Additionally, spruce shoots from seven different rural locations sampled in the years 2000-2004 were analyzed in order to get an overview about the spatial distribution of PCB and PCDD/PCDF. The analytical results of the samples from the two urbanized areas clearly show that the atmospheric contamination with PCDD and PCDF has declined by about 75% between 1985 and 1997 at Warndt and about 40% between 1991 and 1997 at Duebener Heide. However, concentrations stayed virtually constant at both locations from 1997 to 2004 at a level of about 1 ng WHO-TEQ/kg dry matter (d.m.). Similarly, the investigation of spruce shoots from rural locations from 2000 to 2004 did not reveal a temporal trend at any site. PCDD/PCDF levels were between 0.1 and 1.0 ng WHO-TEQ/kg d.m. At the urbanized location Warndt the six indicator PCB as well as the 12 dioxin-like PCB according to WHO revealed a significant decline by more than 75% between 1985 and 1999. Thereafter, PCB levels stayed virtually constant. At the location Duebener Heide an overall decrease of PCB concentrations in pine shoots of about 60% was detected between 1991 and 2004. Spruce shoots from all locations showed a relevant contribution of dioxin-like PCB to the total WHO toxicity equivalent (PCDD/PCDF+PCB). In most samples, the contribution of dioxin-like PCB was between 21% and 41%. The TEQ contribution of PCB in the samples from three rural sites was higher and similar to the TEQ value of PCDD/PCDF. The investigated pine shoots from the urbanized site Duebener Heide showed a 15-28% contribution of dioxin-like PCB to total TEQ and thus lower than in spruce shoots from different locations. In all samples except one PCB 126 contributed to more than 80% to the PCB-TEQ.     

Concentrations of polychlorinated dibenzo-p-dioxins, dibenzofurans and non-ortho substituted biphenyls in polar bear milk from Svalbard (Norway)

Polychlorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF) and non-ortho substituted biphenyls (PCB, CB) were determined in 6 polar bear milk samples from Svalbard (Norway). For these compounds, no data for polar bears have been reported before from this region. Most of the PCDD/PCDF congeners were found at detectable levels. Concentrations expressed as 2,3,7,8-TCDD equivalents (Nordic model) were in the order of 1–3 pg/g⁻¹ fat (0.2–1.6 pg ml⁻¹ milk) which is comparable with ringed and harp seal blubber from the same region. On whole milk basis, concentrations were similar to those found in human milk. An estimation of the daily uptake via milk showed that the intake is lower for polar bears compared to humans. As in human milk, relatively high levels of OCDD were found in some polar bear milk samples. The PCDD/PCDF congener pattern in the milk was different to that found in polar bear fat from the Canadian Arctic. Non-ortho substituted PCB levels in polar bear milk were similar to those found in polar bear fat from the Canadian North. However, CB 77 or 169 dominated in the milk while CB 126 was the most abundant congener in fat. PCDD/PCDF levels expressed as 2,3,7,8-TE were highly correlated with the fat content of the milk. No correlation between CB and PCDD/PCDF concentrations was found. Some data indicate that PCDD/PCDF concentrations in polar bear milk decrease with increasing time after delivery.     

Formation characteristics of PCDD and PCDF during pyrolysis processes

In recent years, pyrolysis processes have become technologies developed to industrial scale and discussed as alternatives to the existing waste combustion technology. However, little information is published regarding PCDD/F formation characteristics during pyrolysis processes. Two common shredder fractions – industrial light shredder (ILS) and refrigerators (REF) – both with high chlorine and copper content were pyrolysed for this pyrolysis study using a pilot plant with a capacity of 100 kg/h. At oxygen concentrations below 2% and temperatures between 430°C and 470°C, considerable amounts of PCDD/F were formed during the pyrolysis. More than 90% of total TEQ was found in the oil fraction (gas phase). The PCDD/PCDF ratio and the homologue pattern differed significantly from those formed during waste incineration. Considering mono- to octachlorinated congeners, up to 400 times more PCDF were formed compared to PCDD. For the investigated pyrolysis conditions, the formation of low chlorinated congeners was highly favoured. The distribution of TEQ within the individual congeners were very similar in all investigated runs. More than 80% of total TEQ stem from 2,3,7,8-substituted T₄CDF and P₅CDF. The isomer pattern, however, did not show significant differences compared to the common waste incineration pattern suggesting that the basic formation routes are similar.     

Monitoring dioxins and furans in a population living near a hazardous waste incinerator: levels in breast milk

In this study, the concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDFs) in breast milk from mothers living in the vicinity of a new hazardous waste incinerator (HWI) were determined. Monitoring was performed after three years of regular operations in the facility and the present results were compared with baseline concentrations obtained in a pre-operational program. PCDD/PCDF levels were determined by HRGC/HRMS in 15 samples. In the present study, PCDD/PCDF concentrations ranged from 4.9 to 39.9 pg I-TEQ/g fat (5.1-46.8 pg WHO-TEQ/g fat), with a median value of 7.7 pg I-TEQ/g fat (9.1 pg WHO-TEQ/g fat). In the baseline survey, PCDD/PCDF concentrations ranged between 5.9 and 17.1 pg I-TEQ/g fat, with a median value of 11.7 pg I-TEQ/g fat. In relation to this, a percentage of reduction of 34.2% was noted. This decrease is in agreement with the relevant reduction found in the dietary intake of PCDD/PCDFs between both surveys. The results of the present study, as well as other recent environmental and biological data, indicate that living in the vicinity of this HWI should not mean additional health risks due to PCDD/PCDFs for the general population.     

Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Analysis of polychlorodibenzo-p-dioxins and dibenzofurans (PCDDs/PCDFs) in baked-salt food additives in Korea

Thirty-one samples of baked-salt products used in commercial food additives were analyzed for the presence of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Dioxins were highly detected in 12 samples of baked salts. The amount of dioxins found in the samples ranged from 12.47 pg/g to 406.56 pg/g (0.71 pg TEQ/g to 23.51 pg TEQ/g, respectively). The most abundant congeners, as TEQ values, were 2,3,4,7,8-PeCDF; 1,2,3,7,8-PeCDF; and 1,2,3,4,7,8-HxCDF in PCDF congeners and 1,2,3,7,8-PeCDD; 1,2,3,6,7,8-HxCDD; and 1,2,3,7,8,9-HxCDD in PCDD congeners. Meanwhile, PCDDs/PCDFs were analyzed in high-temperature-treated samples of natural sea salt alone and natural sea salt to which di-(2-ethylhexyl)phthalate (DEHP) had been added. In the former case, PCDD/PCDF formation was most evident at temperatures near 450 degrees C, the total amount of dioxins was 90.07 pg/g (6.07 pg TEQ/g), and PCDD congeners comprised less than 50% of the total PCDDs/PCDFs. However, when the latter samples were heated, the total PCDD/PCDF concentration was 512.30 pg/g (21.53 pg TEQ/g), with PCDD congeners comprising over 87% of the total PCDDs/PCDFs.     

Steps towards a European dioxin emission inventory

The results of a project aiming at collection and evaluation of information regarding the industrial and non-industrial emission sources for dioxins and furans (PCDD/PCDF) in 17 European Countries (EU 15, CH, N) are presented. An overview about national documents covering dioxin emission inventories for the period 1990-1995 is given. Some data on emissions associated with residual materials, waste and waste water are presented additionally. Based on the air emission data contained in these documents the most important emission sources were determined which are assumed to cover about 90% of the overall emissions. For the selected sources and for all 17 countries new estimates of the atmospheric PCDD/PCDF emissions were derived from average emission factors and statistical activity rates for the year 1994. As a result, on the European scale the largest annual PCDD/PCDF emission is assessed to be released from municipal waste incineration, quite closely followed by emissions from iron ore sintering. Considerable releases of dioxins and furans--based, however, on highly uncertain data--are further assessed for domestic burning, accidental fires and (former) use of contaminated wood preservatives (pentachlorophenol). A lower but still significant emission is further assigned to the sector of non-ferrous metal production; particular processes used in this branch proved to generate very high PCDD/PCDF flue gas concentrations.     

Relevance of PCDD/PCDF formation for the evaluation of POPs destruction technologies--review on current status and assessment gaps

One important criterion for assessment of a POPs destruction technology is the potential formation of new POPs and other toxic by-products, in particular whether the highly toxic PCDDs/PCDFs are formed and under which operation conditions their formation is relevant. For incineration processes the formation mechanisms of PCDDs/PCDFs have been investigated thoroughly and strategies and technologies were developed to minimize their formation and emission. A detailed assessment of non-combustion technologies with respect to PCDD/PCDF formation is, however, lacking to date. A comparison of reaction conditions for PCDD/PCDF formation from precursor formation studies and actual applied conditions of a broad range of POPs destruction technologies in the present paper indicates that the operation conditions for a number of destruction technologies have the potential to generate high concentrations of PCDDs/PCDFs if dioxin precursors are present and that also PCDD/PCDF de novo formation can take place. Therefore a strategy and regulations for a more profound assessment and monitoring of the fate of PCDD/PCDF formation and emission is essential for the evaluation of POP destruction technologies and for a sound risk management of POPs. The present paper aims to provide a critical impulse in this respect, discusses the relevant formation pathways with respect to POPs destruction technologies and proposes a basic framework on how evaluations may be performed.