深度处理后污水用于锅炉补水的可行性研究

在污水处理场,经过生化处理后的排放水中仍含有一定的悬浮物、氨、氮、油、菌类及大量的溶解盐类,其COD也较高,因而不能直接用于锅炉补水。用“斜板沉降-连续过滤-超滤-反渗透”这一组合工艺来处理炼油污水,并将处理后的污水回用于锅炉补水。对其可行性进行了科学的分析和论述,并进行了中试。试验证明,该工艺流程及设备无论在技术上还是在经济上都是可行的。     

三维电极法深度处理环保发电厂垃圾渗滤液的实验研究

采用氨吹脱--三维电极法对广东某环保发电厂经混凝--生化处理后的垃圾渗滤液进行深度处理,实验结果表明:在渗滤液pH为11,温度60℃,吹脱时间50min时脱氨率达95%;脱氨后的渗滤液经三维电极电解处理,COD去除率达81%,颜色清澈,可达《生活垃圾渗滤液排放限值》(GB16889-1997)的二级排放标准。     

含油污水回用处理新工艺研究

研究了一种处理回用含油污水的新工艺,二期炼油污水深度处理中试研究表明,以炼油企业二级处理达标排放污水为处理对象,在使用该工艺处理水量为0.5m3/h、水力停留时间为1.49h 以及污水中COD、氨氮、石油类的浓度变化分别为44.07～102.13 mg/L、28.37～50.01 mg/L、4.10～6.77 mg/L时,平均去除率分别达到94%、96.1%、91.9%,其排出水质符合循环水补充水的水质要求。对该工艺进行了5.5h抗冲击实验,结果表明其抗冲击能力优良。     

厌氧＋移动接触氧化法处理油田污水的中试

Y油田采用"核桃壳过滤+传统活性污泥法"处理油田污水,处理后污水COD、BOD5浓度分别为110.23,38.65mg/L,不能达到GB 18918—2002《城镇污水处理厂污染物排放标准》一级标准,需升级改进处理方法。在油田现场应用"物理过滤+厌氧水解酸化+接触氧化+活性炭吸附"的处理方法,开展了油田污水深度处理中试研究,对现场中试数据进行了分析,结果表明:应用该方法处理的油田污水COD、BOD5等指标能够达到GB 18918—2002《城镇污水处理厂污染物排放标准》一级标准,其中COD、BOD5浓度分别为26.87~37.55mg/L,6.34~7.61mg/L。     

克拉玛依石化公司污水深度处理回用工程

克拉玛依石化公司将污水经深度处理后再回用于循环水补水,由国内几家污水深度处理技术比较成熟的设计单位进行了中试工作,采用了以混凝气浮、臭氧生物活性碳及钠滤除盐为核心的工艺路线。一年多的运行监测数据表明,克拉玛依石化公司污水经深度处理后,回用循环水系统的腐蚀率小于0.100mm/a,达到中国石油总公司《工业水管理》规定的控制指标。各流程单元设计针对性强,技术成熟,处理效果稳定可靠,符合炼油废水的水质特点。该工艺技术先进、运行可靠,具有工业化推广价值。     

污水深度处理及回收利用的可行性分析

大庆炼化公司从单一化工污水深度处理及回收利用发展为炼油、化工、生活污水统一处理和回用于循环水,既充分利用了现有污水处理场的处理余量,同时由于生活污水中含有比例适当的微生物需要的营养物质,对炼油和化工污水起到补充和稀释作用。这种处理方法既降低了工业污水对污水处理场的冲击,又起到了稳定水质的作用。     

石油化工企业含苯胺消防污水处理技术研究

针对石油化工企业含苯胺的消防污水,利用基于过氧化氢和氯化铁为氧化剂的深度氧化技术,通过氧化、絮凝、过滤和吸附对消防污水进行处理。实验确定氧化剂的投加量为理论投加量,氧化时间1.0h,消防污水pH值为6.86时,絮凝剂最佳使用浓度约为2%,消防污水中苯胺和COD去除率达到99.5%以上,达到了消防污水处理效果。     

炼油污水深度处理回用工艺实验研究

试验工艺流程的方案选定,充分吸收了各炼油厂进行的污水深度处理的成功试验经验,以原臭氧生物活性炭工艺单元为基础,提出了以混凝气浮与臭氧生物活性炭串联工艺为核心的总体工艺流程,以降低工程投资及处理成本,提高污水回用的经济效益;同时,指出试验过程中所存在的问题及其对策。因此,开展炼油污水深度处理回用工艺试验研究,必将为炼油污水深度处理提供强有力的技术支撑,可作为相关污水回用处理工艺选择的参考。     

城镇污水处理厂NPR工艺低温运行的效能分析

介绍了天津市某城镇污水处理厂NPR工艺的特点及运行状况。通过对污水厂的运行监测数据分析,研究了该工艺在低温条件下处理城镇生活污水时的脱氮除磷效果。结果表明:NPR工艺具有一定的优异性,它能在降低能耗的前提下使系统COD和SS的去除率进一步降低,出水能达到中水回用标准,有利于污水的再生利用;低温影响NPR系统的硝化及反硝化率,低温下有机物的去除更易受到有机负荷的影响;温度对生物去除SS,COD和TP的效果影响不大,对NH3-N及TN的去除效果影响比较明显。低温下污水处理厂COD、SS、NH3-N、TN、TP的平均去除率分别为72.1%、94.9%、67.5%、55.1%、66.5%。     

炼厂隔油后污水的有机构成及混凝处理

采用GC/MS技术分析了炼厂隔油后污水的有机组成,并研究了不同混凝剂处理污水的效果,以及对有机构成的影响。结果表明,隔油后污水中的有机物质主要是C6–C8,其中酚类物质的含量最高;PAM和PAC混凝处理隔油后污水,可使污水中的有机物质总浓度及各物质的相对比例均发生变化,PAM降低烃类物质的效果好于PAC,而后者降低酚类物质的效果好于前者;在PAC处理污水时,同时投加少量活性炭可有效改变PAC脱除COD的性能。     

高氨氮污水和高浓度有机废水综合治理

选用以曝气生物流化池(ABFT)技术为核心、辅助以物理化学方法的工业化技术,对兰州石化公司高氨氮污水和高浓度有机废水进行了处理。处理结果显示:外排废水监测项目中pH值、悬浮物、COD、BOD5、氨氮、石油类、硫化物、氰化物、挥发酚的平均浓度均低于污水综合排放标准(GB8978-1996)的一级标准,其中:氨氮值仅为0.412mg/L,COD值为63.87mg/L。对COD、氨氮、硫化物、挥发酚、悬浮物等的去除率达到90%以上,石油类和BOD5的去除率也达到75%以上,取得了良好的效果。     

制药废水生化处理后的深度处理方法比较研究

随着制药废水排放标准的提高,对制药废水进行深度处理是实现其达标排放的有效途径之一。试验比较了絮凝、高级氧化、吸附、超滤等方法对生化处理后的高浓度制药废水深度处理效果,结果表明:4种方法中,只有活性炭吸附对废水COD、浊度、色度、氨氮等都具有较好的去除效果,COD去除率最高能达到62%,可实现达标排放。     

DOMESTIC WASTEWATER TREATMENT BY PEATLANDS IN A NORTHERN CLIMATE: A WATER QUALITY STUDY1

ABSTRACT: The use of peatlands as the main form of wastewater treatment in a northern climate was studied for the James Bay Energy Society. The Fontanges campsite (70° 17′ 30″ W; 54° 34′ 00″ N) was chosen as the study site. In less than 1.5 km from the point of discharge BOD₅, COD, total hardness, inorganic carbon, orthophosphates, total phosphorus, ammonia and total nitrogen were reduced by at least 90 percent. The peatland treatment system studied is divided into four components, each having a specific function. The first part combines the action of microorganisms and adsorption on peat, thus reducing the organic content while increasing the inorganic constituents. The second part uses peat to adsorb the inorganic elements already present in the wastewater and those produced in the first part of the system. The third component acts as an aerator, increasing the dissolved oxygen and decreasing the BOD₅ levels of the water. The fourth part removes most of the remaining nutrients, thus acting like a tertiary treatment. Overall, peatlands seemed to be effective in treating domestic settled wastewater in a cold climate.     

Evaluation of municipal wastewater treatment plants with different technologies at Las Rozas, Madrid (Spain)

Eight small-scale municipal wastewater treatment plants were evaluated over a period of 19 months in the suburb of Las Rozas in Madrid (Spain). Four plants used compact extended aeration, two used conventional activated sludge, two used conventional extended aeration, one used a rotary biodisc reactor and the other used a peat bed reactor. The best results were obtained from the plants that used conventional technologies and the biodisc. Conventional activated sludge and extended aeration had higher removal efficiencies for ammonia, TSS, COD and BOD(5) and produced good quality final effluents for final disposal in accordance with the discharge standard. Empirical equations that correlated the concentration of dissolved oxygen in the effluents with the efficiencies of TSS, ammonia, COD and BOD(5) removals for all plants evaluated were obtained. The performance of the plants using compact extended aeration was affected more than those using conventional technologies or rotary biodisc when the capacity exceeded that of its initial design.     

Regeneration of industrial district wastewater using a combination of Fenton process and ion exchange—A case study

Regeneration studies of wastewater effluent from an organized industrial district (OID) for possible reuse in textile industry as process water was investigated. Advanced treatment methods including Fenton process, polyaluminium chloride (PAC) coagulation and ion exchange were applied on OID effluent. In Fenton process removal efficiencies for suspended solids (SS), chemical oxygen demand (COD), SAC₄₃₆ (spectral absorption coefficient), SAC₅₂₅ and SAC₆₂₀ were determined 61%, 36%, 35%, 49% and 67%, respectively. After Fenton process, wastewater samples were coagulated with PAC. Optimum removal efficiencies for SS, COD, Fe ion, SAC₄₃₆, SAC₅₂₅ and SAC₆₂₀ were determined 83%, 18%, 93%, 32%, 36% and 58%, respectively. Ion exchange experiments were conducted on chemically coagulated wastewater samples to improve the quality of wastewater. Optimum dosage of resins was determined. The experiments revealed that 1:1 resin ratio (20 mL H-type resin:20 mL OH-type resin) gave the best removal rates for the parameters considered in this study. Study results indicated that quality of the wastewater was suitable for the process water characteristics of textile industry and unit wastewater treatment cost was determined as 2.54 €/m³.     

常用氧化剂性能研究

用四种常用的氧化剂:高锰酸钾、漂白粉、NaClO和H2O2/Fe2+对大港油田港深11井酸化废水进行了处理。考察了氧化剂的投加量、氧化时间和pH值对酸化废水色度和COD去除率的影响。实验结果表明,在最佳条件下,H2O2/Fe2+对酸化废水的色度和COD的去除率最高;用高锰酸钾处理废水,其COD去除率较高,但脱色效果差;而漂白粉和NaClO的脱色率较高,但其氧化能力有限。建议油田用氧化法处理废水时应采用H2O2/Fe2+催化氧化体系。     

聚合硅酸硫酸铁处理印染废水的实验研究

介绍了聚合硅酸硫酸铁的制备及处理印染废水的方法,研究了最佳的实验条件。该方法工艺流程简单,药剂成本较低,废水的COD去除率达80%,脱色率达90%,出水水质达到了印染废水综合排放标准(GB8978-1996)一级标准。     

工业园区污水处理工艺的运行及完善探讨

本文对某工业园区的综合废水处理工艺开展了连续两年的运行调查,进行了其工艺完善及提标改造的技术探讨。研究表明,改造前该污水处理装置的出水COD、BOD5、总磷、SS均能达到排放标准,而唯独出水氨氮处理效果差,难以达到一级排放标准要求。通过增设预处理水解装置、生物氧化装置导流墙容积比改进、生物塘深度处理工艺完善后,能够保证出水氨氮的处理效果且能达到一级A排放标准。     

抗生素药生产废水处理工艺改进研究

企业抗生素废水经原有工艺处理后污染物指标偏高,且不稳定。工艺通过采用增加初沉池和二沉池、污泥回用等改进措施,COD、氨氮等排放浓度下降且稳定排放,改进效果明显。