压力溶气气浮工艺中溶气效率测定方法述评

气浮工艺中溶气效率高低直接影响到回流水量的大小，即决定着运行费用的高低。对气浮工艺设计者和运营者来讲，达到并维持较高溶气效率是优先考虑的问题，而对新型气浮设备研发者而言，了解并确定其在不同工况下的溶气效率也是至关重要的。就已有溶气效率的测定方法进行了分类介绍与评价。     

加压溶气气浮设备理论溶气量的计算

本文通过对加压溶气过程的分析 ,建立了理想加压溶气过程模型 ,在此基础上推导出新的理论溶气量计算公式 ,并与现有的计算公式进行了比较。     

加压溶气气浮设备理论溶气量的计算

本文通过对加压溶气过程的分析，建立了理想加压溶气过程模型，在此基础上推导出新的理论溶气量计算公式，并与现有的计算公式进行了比较。     

加压溶气生化气浮法降解生活污水中有机物

将加压曝气生物氧化技术与加压溶气气浮工艺相结合,开发了一种快速处理生活污水的加压溶气生化气浮反应器(PA-DAF),并考察了反应器的泥水分离效果及压力、水力停留时间(HRT)、气水比对其去除生活污水内有机物的影响。实验结果表明,在压力0.4 MPa,HRT 1.5 h(Q=1.0 L/min),气水比3∶1的条件下,生活污水COD去除率可稳定在90%左右。同时发现,NH3-N去除效果不理想,有待后续研究进行优化。     

3种内筒溢流型溶气罐结构改进设计方案的溶气性能对比分析

溶气罐是溶气释放式微气泡发生系统的关键设备,其中内筒溢流型溶气罐具有结构简单、成泡粒径小等优点.提出了3种内筒溢流型溶气罐的结构改进设计方案,并对其在不同操作参数下的溶气性能进行了对比分析.为克服通过测量释气量间接表征溶气量所带来的系统误差,建立了在线带压测量溶解氧的方法,并以空气在水中溶解量的变化率(即溶气效率)来直接表征溶气罐的溶气性能.结果表明:溶气效率随气液比和溶气压力的增大而增加,随液位比的升高而减小;在相同气液比、液位比及溶气压力下,气液切向进口加螺旋导叶片型溶气罐的溶气效率最高.采用响应曲面法对溶气性能相对最佳的内筒溢流型溶气罐的操作参数进行优化,预测最高溶气效率为72.43％时的最佳操作参数为:气液比为0.25,液位比为0.36,溶气压力为0.26 MPa.所得回归模型预测值与实测值的相对误差为0.87％,表明该模型可较好地分析和预测溶气罐的溶气性能.     

三种气液混合泵气浮系统处理低浓度二级出水的对比研究

以低浓度的二级出水为处理对象,利用小试装置,以COD、TP和浊度为考察指标,对使用气液混合泵溶气的全溶气、部分溶气和回流加压溶气气浮系统进行了对比研究.结果表明,回流加压溶气气浮系统对3个指标的去除率明显高于全溶气和部分溶气气浮系统,而部分溶气气浮系统对COD、TP的去除率略高于全溶气气浮系统;二级出水浊度较低时,全溶气和部分溶气气浮系统的出水浊度反而升高,因此使用气液混合泵溶气的全溶气和部分溶气气浮系统不适合处理低浊度的二级出水.     

气浮技术在膜生物反应器剩余污泥浓缩过程中的应用

污泥浓缩作为污泥处理的关键环节之一,开发高效的污泥浓缩工艺对于降低污泥含水率、提高脱水设备的运行效率、降低脱水能耗具有十分重要的意义。针对MBR污泥浓度高、污泥粒径小、污泥沉降性能较差等特点,故采用传统的重力浓缩和机械浓缩技术很难有效实现污泥浓缩。因此,尝试采用气浮浓缩技术降低污泥含水率的可行性。从气浮浓缩的中试结果来看,较适宜运行参数为:固体负荷为15 kg/(m2·h),水力负荷为1.5 m3/(m2·h),回流比为1,PAM投配率2‰(w/w干固体),溶气压力为0.4 MPa,气固比为0.03。经过中试设备进行气浮浓缩后,污泥含水率降低至96%左右。此外,还研究了采用气液多相泵系统对剩余污泥的浓缩效率,结果显示,该设备的使用相对于传统溶气气浮工艺,其优点表现在占地小、工程造价低以及运行成本低等方面。     

混凝气浮-过滤法处理油田超稠油废水

辽河油田某配液站超稠油废水为成分十分复杂的有机混合物,对其采用混凝气浮-过滤工艺进行处理,同时改进压力溶气罐、释放器、气浮机和压力过滤器等设备,并对加药位置进行了优化选择,使该废水的处理取得了理想的效果,出水含油和SS均低于10 mg/L.     

臭氧气浮工艺絮体尺度与界面理化特性调控

针对臭氧气浮工艺对有机物脱色和去除性能的限制,通过阴、阳离子型聚丙烯酰胺(ployacrylamide,PAM)对以腐殖酸为代表的天然有机物絮体的尺度调控,采用气载絮体尺度、二维分形维数及絮体与微气泡间的接触角对PAM浓度梯度下形成的气载絮体进行了表征;研究了阴阳离子型PAM浓度梯度对腐殖酸的降解效果和气载絮体尺度;并探讨了阴阳离子型PAM、絮体与微气泡间的结合机理。结果表明:PAM的投加提高了臭氧气浮工艺中腐殖酸的去除性能,且气载絮体尺寸、分形维数和接触角均有所增大;在不同类型PAM中均存在最佳PAM剂量,在此剂量下,体系内去除效果、气载絮体大小和接触角最大、分形维数最小;在最佳PAM剂量下,与阴离子型PAM相比,阳离子型PAM形成气载絮体的大小和接触角较大,分形维数较小,且去除效果较好。在臭氧气浮体系中,通过改善PAM、絮体与微气泡结合静电作用力的强弱形成了利于气浮的气载絮体尺度,提高了对腐殖酸的去除效果。     

污水污泥中重金属污染物的溶出过程研究

污水污泥中污染物尤其是重金属的水体浸出作为重要的二次污染途径备受关注。为了探讨污水污泥中重金属的溶出规律,对上海7个污水处理厂的污水污泥进行了重金属总量分析,并采用水平振荡法对上述污水污泥中重金属进行了溶出动力学研究。结果表明,污水污泥中Cu、Cr和Zn的含量均较高,之后依次是Pb、As、Cd和Hg;污水污泥中重金属溶出动力学过程分为快速反应和慢速反应两个过程,可以用Elovich方程进行模拟;污水污泥中各重金属的溶出负荷差异较大,Cu、Cr和Zn的溶出负荷较大,其他较小,但各重金属相对于污水污泥中重金属总量的溶出百分比差异不大,基本处于10%以下。     

气浮净水技术研究及进展

本文系统总结了目前气浮净水技术的研究现状,着重阐述了溶气气浮机理及气浮池的设计、影响气浮效果的因素、气浮技术的评价及应用现状,同时对有关溶气气浮技术的模型及新概念,以及溶气气浮技术的发展方向进行了论述。     

染整废水处理工程设计

采用“生物接触氧化 +混凝气浮 +生物炭”工艺处理染整废水 ,COD去除率可达到 90 %以上 ,工程实践表明 ,该工艺处理效果好 ,运行稳定 ,投资省 ,处理后出水可达标排放     

Assessing the efficacy of dissolved air and flash-pressurized flotations using low energy for the removal of organic precursors and disinfection byproducts: a pilot-scale study

Environmental Science and Pollution Research - Dissolved air flotation (DAF) is a widely used treatment process in drinking water and wastewater treatment plants despite high energy cost associated...     

Multispectral image analysis method to determine dynamic fluid saturation distribution in two-dimensional three-fluid phase flow laboratory experiments

The need for measuring dynamic fluid saturation distribution in multi-dimensional three-fluid phase flow experiments is hampered by lack of appropriate techniques to monitor full field transient flow phenomena. There is no conventional technique able to measure dynamic three-fluid phase saturation at several array points of the flow field at the same time. A multispectral image analysis technique was developed to determine dynamic NAPL, water and air saturation distribution in two-dimensional three-fluid phase laboratory experiments. Using a digital near-infrared camera, images of sand samples with various degrees of NAPL, water and air saturation were taken, under constant lighting conditions and within three narrow spectral bands of the visible and near-infrared spectrum. It was shown that the optical density defined for the reflected luminous intensity was a linear function of the NAPL and the water saturation for each spectral band and for any two and three-fluid phase systems. This allowed the definition of dimensionless lump reflection coefficients for the NAPL and the water phase within each spectral band. Consequently, at any given time, two images taken within two different spectral bands provided two linear equations which could be solved for the water and the NAPL saturation. The method was applied to two-dimensional three-phase flow experiments, which were conducted to investigate the migration and the distribution of LNAPL in the vadose zone. The method was used to obtain continuous, quantitative and dynamic full field mapping of the NAPL saturation as well as the variation of the water and the air saturation during NAPL flow. The method provides a non-destructive and non-intrusive tool for studying multiphase flow for which rapid changes in fluid saturation in the entire flow domain is difficult to measure using conventional techniques.     

混凝-气浮控制三卤甲烷生成势的研究

研究了混凝一气浮工艺对不同分子量区间三卤甲烷生成势（trihalomethanes formation potential，THMFP）的去除效果及絮体形态对THMFP去除效果的影响。结果表明，混凝一气浮工艺以去除大分子量区间THMFP为主，对小分子量区间THMFP的去除效果较差。UV254值与THMFP值的线性相关系数为0．9449，UV254值可以较好地反映THMFP的含量。絮体的分形维数为1．17～1．2时，孔隙率较大，可增加絮体对THMFP的活性吸附空间，且絮体相对密度较小，可增强同向絮凝作用，增加絮体和THMFP的接触概率，有利于气浮对THMFP的去除。     

A field comparison of BTEX mass flow rates based on integral pumping tests and point scale measurements

Measuring contaminant flow rates at control cross sections is the most accurate method to evaluate natural attenuation processes in the saturated subsurface. In most instances, point scale measurement is the method of choice due to practical reasons and cost factors. However, at many field sites, the monitoring network is too sparse for a reliable estimation of contaminant and groundwater flow rates. Therefore, integral pumping tests have been developed as an alternative. In this study, we compare mass flow rates obtained by integral pumping test results and point scale data. We compare results of both methods with regard to uncertainties due to estimation errors and mass flow estimations based on two different point scale networks. The differences between benzene and groundwater flow rate estimates resulting from point scale samples and integral pumping tests were 6.44% and 6.97%, respectively, demonstrating the applicability of both methods at the site. Point scale-based data, especially with use of cost efficient Direct-Push technique, can be applied to show the contaminant distribution at a site and may be followed by a denser point scale network or an integral method. Nevertheless, a combination of both methods decreases uncertainties.     

A coupled simulation-optimization approach for groundwater remediation design under uncertainty: An application to a petroleum-contaminated site

This study provides a coupled simulation–optimization approach for optimal design of petroleum-contaminated groundwater remediation under uncertainty. Compared to the previous approaches, it has the advantages of: (1) addressing the stochasticity of the modeling parameters in simulating the flow and transport of NAPLs in groundwater, (2) providing a direct and response-rapid bridge between remediation strategies (pumping rates) and remediation performance (contaminant concentrations) through the created proxy models, (3) alleviating the computational cost in searching for optimal solutions, and (4) giving confidence levels for the obtained optimal remediation strategies. The approach is applied to a practical site in Canada for demonstrating its performance. The results show that mitigating the effects of uncertainty on optimal remediation strategies (through enhancing the confidence level) would lead to the rise of remediation cost due to the increase in the total pumping rate.     

混凝一气浮控制三卤甲烷生成势的研究

研究了混凝一气浮工艺对不同分子量区间三卤甲烷生成势（trihalomethanes formation potential，THMFP）的去除效果及絮体形态对THMFP去除效果的影响。结果表明，混凝一气浮工艺以去除大分子量区间THMFP为主，对小分子量区间THMFP的去除效果较差。UV254值与THMFP值的线性相关系数为0．9449，UV254值可以较好地反映THMFP的含量。絮体的分形维数为1．17～1．2时，孔隙率较大，可增加絮体对THMFP的活性吸附空间，且絮体相对密度较小，可增强同向絮凝作用，增加絮体和THMFP的接触概率，有利于气浮对THMFP的去除。     

Applicability of a sharp-interface model for estimating steady-state salinity at pumping wells--validation against sand tank experiments

A numerical sharp-interface model of saltwater and freshwater behavior was validated against experiments conducted in two small scale sand tanks. A simple algorithm was proposed to determine saltwater and freshwater withdrawal rates at a pumping well at which a total pumping rate was specified. Model estimates were compared with transient salinity breakthroughs and steady-state salinities of water extracted from pumping wells in the sand tanks. Experimental scenarios included various combinations of freshwater pumping and injection and saltwater pumping. The corresponding Nash-Sutcliffe model efficiency was 0.95, which showed that the agreement between observations and computed results was satisfactory.     

Removal of emulsified fuel oils from brackish and pond water by dissolved air flotation with and without polyelectrolyte use: pilot-scale investigation for estuarine and near shore applications

In coastal areas, estuaries, and inland waters, dispersant use after oil spills is not allowed due to sensitivity of the ecosystems. The purpose of this study was to investigate the removal of emulsified fuel oils from brackish and pond water by dissolved air flotation (DAF) with and without use of coagulants. Experiments were conducted with a 60 L DAF system. Fuel oil-water emulsions were prepared with regular unleaded gasoline, jet fuel, and diesel fuel mixed at 1:1:1 (v/v/v) ratio. Batch and continuous runs were conducted at air pressurization of 354.6 kPa. During both batch and continuous modes, significant petroleum hydrocarbon (PHC) removal was achieved within 10 min. Coagulant addition initially increased the PHC removal by about 5-15%. However, effectiveness of the coagulant was not significant after 20 min due to breakage of the aggregates. In general, the pond water had higher PHC removal than the brackish water. With longer run times, PHC removal improved slightly and the effluent contained increasing fractions of higher molecular weight compounds indicating that PHC removal was due to both DAF and stripping processes. Results indicate that DAF process can be effective both with and without the use of coagulants for removing PHCs from brackish and pond waters.