Temperature activated degradation (mineralization) of 4-chloro-3-methyl phenol by Fenton's reagent

With the aim to evaluate the effect of temperature, 4-chloro-3-methyl phenol (CMP) degradation by Fenton's reagent was investigated at 25 and 70 degrees C under the following initial conditions: [CMP]0 = 10 mM, [Fe2+]0 = 0.5 mM; ([H2O2]0/[CMP]0) = 80, pH0 = 3. The results indicated that CMP degradation was strongly influenced by temperature. In fact, the maximum TOC removal, achieved after ca. 24h, was by far greater at 70 degrees C (85%) than at 25 degrees C (36%). The same happened for organic chlorine (TOX) conversion into inorganic chloride, i.e. 100%, after 3 h at 70 degrees C, and 87%, after 27 h at 25 degrees C. As the recorded trends of CMP removal and chloride formation were basically the same, hydroxy substitution (ipso-substitution) was hypothesised as one likely mechanism of CMP degradation. The higher level of mineralization recorded at 70 degrees C was ascribed to: (i) a greater *OH concentration; (ii) a consequently greater extent of CMP oxidation to organic acids; (iii) a higher decarboxylation rate of such acids. An interesting consequence of such extended organic acids decarboxylation was a pH increase up to 8 that, in turn, caused, in the treated mixture, the decomposition of excess H2O2 as well as the precipitation of iron ions. These two latter outcomes are technologically important considering that usually, before discharging Fenton treated wastewater, specific polishing steps are required just to remove iron ions, decompose excess hydrogen peroxide and neutralise the pH.     

Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

High temperature dependence of 2,4-dichlorophenoxyacetic acid degradation by Fe3+/H(2)O(2) system

This study demonstrates the importance of reaction temperature on the degradation of 2,4-dichlorophenoxyacetic acid (2,4-D). In addition, we provide a mechanistic explanation for the temperature dependence of 2,4-D degradation. Thermal enhancement of 2,4-D degradation and H(2)O(2) decomposition was measured in the absence and in the presence of the z.rad;OH scavenger (t-butanol). The half-life for 2,4-D degradation was reduced by more than 70-fold in the absence of t-butanol, and by more than 700-fold, in the presence of t-butanol, when the reaction temperature was increased from 10 to 50 degrees C. In addition, similar temperature relationships were found for H(2)O(2) decomposition. The major reason for the high temperature dependence of the Fe(3+)/H(2)O(2) system in the case of 2,4-D degradation is due to the dependence of the initiation reaction of the Fe(3+)/H(2)O(2) system (i.e., Fe(3+)+H(2)O(2)-->Fe(2+)+HO(2)(z.rad;)+H(+) upon temperature), which is entirely consistent with the kinetics of the activation energy. In the presence of a z.rad;OH scavenger, the initiation reaction of the Fe(3+)/H(2)O(2) system became a determining factor of this temperature dependence, whereas in the absence of z.rad;OH scavenger, several other radical reactions played a role and this result in an apparent decrease in the activation energy for 2,4-D degradation. Moreover, the enhanced 2,4-D removal at higher temperatures did not alter H(2)O(2) utilization. The practical implications of the thermal enhancement of the Fe(3+)/H(2)O(2) system are discussed.     

Optimization of photo-Fenton process parameters on carbofuran degradation using central composite design

Carbofuran, one of the most toxic and biorefractory carbamate compounds, is widely used in insecticides in Taiwan (9-18% of total insecticides production per year). In the present study, a central composite design experiment was used to study the effect of photo-Fenton treatment on carbofuran solution and to optimize the process variables such as carbofuran concentration (1-100 mg L(-1)), H(2)O(2) dosage rate (0.25-6 mg L(-1) min(-1)) and Fe(3+) dosage (1-50 mg L(-1)), which influenced the efficiency of carbofuran degradation and mineralization. The results indicated that all the variables investigated in this study had significant roles in the degradation and mineralization of carbofuran in solution. The carbofuran degradation and mineralization efficiencies were increased with increase in H(2)O(2) dosage rate and Fe(3+) dosage, and with decrease in carbofuran concentration. Furthermore, optimum values of both H(2)O(2) dosage rate and Fe(3+) dosage were found to shift to higher values as carbofuran concentration increased. Based on the model obtained in this study, optimum H(2)O(2) dosage rate and Fe(3+) dosage were found to be 4 mg L(-1) min(-1) and 20 mg L(-1), respectively, for 51 mg L(-1) of carbofuran concentration. Under these conditions, carbofuran was completely removed within 30 min and coupled with 78% mineralization at the end of experiment.     

Kinetics of oxidation of chlorobenzenes and phenyl-ureas by Fe(II)/H2O2 and Fe(III)/H2O2. Evidence of reduction and oxidation reactions of intermediates by Fe(II) or Fe(III)

The rates of degradation of 1,2,4-trichlorobenzene (TCB), 2,5-dichloronitrobenzene (DCNB), diuron and isoproturon by Fe(II)/H2O2 and Fe(III)/H2O2 have been investigated in dilute aqueous solution ([Organic compound]0 approximately 1 microM, at 25.0 +/- 0.2 degrees C and pH < or = 3). Using the relative rate method with atrazine as the reference compound, and the Fe(II)/H2O2 (with an excess of Fe(II)) and Fe(III)/H2O2 systems as sources of OH radicals, the rate constants for the reaction of OH* with TCB and DCNB were determined as (6.0 +/- 0.3)10(9) and (1.1 +/- 0.2)10(9) M(-1) s(-1). Relative rates of degradation of diuron and isoproturon by Fe(II)/H2O2 were about two times smaller in the absence of dissolved oxygen than in the presence of oxygen. These data indicate that radical intermediates are reduced back to the parent compound by Fe(II) in the absence of oxygen. Oxidation experiments with Fe(III)/H2O2 showed that the rate of decomposition of atrazine markedly increased in the presence of TCB and this increase has been attributed to a regeneration of Fe(II) by oxidation reactions of intermediates (radical species and dihydroxybenzenes) by Fe(III).     

Fe(3+)- and Cu(2+)-reduction by phenol derivatives associated with Azure B degradation in Fenton-like reactions

Several phenol derivatives were evaluated regarding their capacities for Fe(3+) and Cu(2+) reduction. Selected compounds were assayed in Fenton-like reactions to degrade Azure B. 3,4-Dihydroxyphenylacetic, 2,5-dihydroxyterephtalic, gallic, chromotropic and 3-hydroxyanthranilic acids were the most efficient reducers of both metallic ions. The reaction system composed of 3-hydroxyanthranilic acid/Fe(3+)/H(2)O(2) was able to degrade Azure B at higher levels than the conventional Fenton reaction (87% and 75% of decolorization after 20min reaction, respectively). Gallic and syringic acids, catechol and vanillin induced Azure B degradations at lower levels as compared with conventional Fenton reaction. Azure B was not degraded in the presence of 10% (v/v) methanol or ethanol, which are OH radical scavengers, confirming the participation of this radical in the degradation reactions. Iron-containing reactions consumed substantially more H(2)O(2) than reactions containing copper. In iron-containing reactions, even the systems that caused a limited degradation of the dye consumed high concentrations of H(2)O(2). On the other hand, the reactions containing Fe(3+), H(2)O(2) and 3-hydroxyanthranilic acid or 3,4-dihydroxyphenylacetic acid were the most efficient on degradation of Azure B and also presented the highest H(2)O(2) consumption. These results indicate that H(2)O(2) consumption occurs even when the dye is not extensively degraded, suggesting that part of the generated OH radicals reacts with the own phenol derivative instead of Azure B.     

微波促进含Cr(VI)-H2O2体系降解甲基橙溶液的研究

研究了微波辐射下Cr(VI)－H₂O₂催化降解甲基橙溶液的行为，探索了微波功率、微波辐射时间、pH值、H₂O₂浓度、Cr(VI)等对甲基橙溶液脱色率和COD去除率的影响。研究结果表明，Cr(VI)-H₂O₂能形成类Fenton体系；微波辐射可提高H₂O₂产生羟基自由基(·OH)的效率。1000 mg/L的甲基橙溶液，在Cr(VI)浓度为10.0 mmol/L、pH值为2.5、H₂O₂浓度为20.0 mmol/L、微波功率为700W下加热2 min，甲基橙溶液的脱色率为99.2%，COD去除率为82.8%。     

Comparison of fenton and photo-fenton processes for livestock wastewater treatment

In this study, the photochemical degradation of livestock wastewater was carried out by the Fenton and Photo-Fenton processes. The effects of pH, reaction time, the molar ratio of Fe(2 +)/H(2)O(2), and the Fe(2 +) dose were studied. The optimal conditions for the Fenton and Photo-Fenton processes were found to be at a pH of 4 and 5, an Fe(2 +) dose of 0.066 M and 0.01 M, a concentration of hydrogen peroxide of 0.2 M and 0.1 M, and a molar ratio (Fe(2 +)/H(2)O(2)) of 0.33 and 0.1, respectively. The optimal reaction times in the Fenton and Photo-Fenton processes were 60 min and 80 min, respectively. Under the optimal conditions of the Fenton and Photo-Fenton processes, the chemical oxygen demand (COD), color, and fecal coliform removal efficiencies were approximately 70--79, 70--85 and 96.0--99.4%, respectively.     

Electrochemical degradation of bromopyrogallol red in presence of cobalt ions

This paper summarizes the results of a degradation test of bromopyrogallol red (BPR) and textile dye wastewater (TDW) with a conventional three-electrode potentiostatic system in the presence of cobalt ions (electro Co(2+)-H2O2 system). H2O2, produced by the two-electron reduction of O2 at the cathode, would react with Co2+ ions, leading to the generation of hydroxyl radicals (*OH), which caused the degradation of the organic pollutants. With BPR degradation process as the reference point, the optimal conditions (pH=4.0 and the concentration of Co2+ is 0.1 mM) and the treating capacity of the system were both studied and compared with electro-Fenton's reagent. Many benefits were shown by the electro Co(2+)-H2O2 system, such as less metal ions consumption, more moderate conditions and faster reaction process. Treated with the system for 0.5 h, chemical oxygen demand and biological oxygen demand of TDW (pH=5.2), without pH adjustment, were reduced by 95.7% and 92.7%, respectively. These characteristics make the method another appropriate solution for wastewater treatment, especially for those contaminated by organic pollutants.     

Use of abiotic oxidative-reductive technologies for remediation of munition contaminated soil in a bioslurry reactor

The possibility to clean-up TNT contaminated soil, 400 mg TNT kg-1, surrounding Nebraska Ordnance Plant's (US), below the USEPA goal of 17.2 mg TNT kg-1 using Fenton oxidation (Fe2+ + H2O2), Fe0 reduction, combined Fe0/H2O2 and CaO2 was explored at pilot scale. Treatments were performed in a 60 l airlift reactor, which was a prototype of larger commercial unit. All the treatments reduced TNT soil concentration below the required clean-up goal and in shorter time with respect to bench scale. Using 2% (w/w) Fe0, TNT soil concentration reduced below the required standard just within 4 h. No significant TNT destruction improvement was observed when 2% Fe0 (w/w soil) was combined with four sequential additions of 0.25% H2O2. Laboratory experiments with 14C-TNT indicated that most of the 14C, approximately 80%, was unextractable residue. A time greater than 24 h was required either with Fenton reagent, 8 x (80 mg Fe2+ L-1 + 0.125% H2O2) or 0.2% (w/w) CaO2. The optimal performance of Fenton reagent was obtained when the reagent was added in eight increments rather than in a single or double dose and less cumulative amount of H2O2 (0.75%) was required with respect to bench scale (1%).     

Sonolysis of alkylphenols in aqueous solution with Fe(II) and Fe(III)

The sonolytic degradation of alkylphenols (APs), such as butylphenol, pentylphenol, octylphenol, and nonylphenol (NP), in water was investigated at a sound frequency of 200 kHz with an acoustic intensity of 6 W cm(-2) under argon, oxygen, and air atmospheres. The sonolytic degradation rate of the APs under the conditions of the present study depended upon their alkyl chain length. The decrease in the degradation rate by the radical scavenging effect was in the range of about 48-82% for APs in the presence of 3 mM 2-methyl-2-propanol. The free radicals play a significant role in the sonolytic degradation process of the APs. In the presence of Fe(II) and Fe(III), the pseudo-first-order rate constants for the sonolytic degradation of 30 microM NP as a function of the concentration of Fe(II) and Fe(III) were estimated under argon and oxygen. The maximum rate constants were observed at 50 microM Fe(II) (0.139 +/- 0.008 min(-1)) and 100 microM Fe(III) (0.103 +/- 0.001 min(-1)) under oxygen. The total organic carbon concentration (TOC) was investigated under same conditions. TOC decreased in the range of about 50-70% during the sonication in the presence of Fe(II) and Fe(III) under argon and oxygen. The sonochemical effects by the addition of Fe(II) and Fe(III) as catalyst during the sonication under the proper atmosphere result in a remarkable enhancement of degradation and mineralization.     

Catalytic oxidation of pentachlorophenol in contaminated soil suspensions by Fe+3-resin/H2O2

Pentachlorophenol (PCP) is a wood preserving agent that is commonly found in contaminated soils at wood treatment sites. The catalytic properties of Fe+3-resin for the oxidation of PCP in aqueous solution and soil suspension with H2O2 were tested. Batch tests in aqueous solution were performed at various dosages of catalyst and H2O2, and reaction temperatures. The results showed that the oxidation of PCP in aqueous solution depends on the dose of H2O2 and the temperature. Essentially complete oxidation of 100 mgl(-1) PCP was obtained with 0.5% Fe+3-resin catalyst, 0.1 M H2O2 and at a reaction temperature of 80 degrees C. The oxidation of PCP achieved in three different soil suspensions was more than 94% within 30-50 min. Moreover, it was demonstrated that the same Fe+3-resin could be reused for at least six cycles of PCP oxidation in soil solutions without loss in efficiency unless the pH of the reaction falls below 5. It was proposed that the loss in used Fe+3-resin catalyst activity could be related to the leaching of Fe+3 at low pH.     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

Catalytic degradation of Orange II by UV-Fenton with hydroxyl-Fe-pillared bentonite in water

Although homogeneous photo-Fenton system is a very efficient method for organic wastewater treatment, it suffers from costly pH adjustment as well as difficult separation of catalysts from aqueous in practical application. Through cation exchange reaction, hydroxyl-Fe-pillared bentonite (H-Fe-P-B) was successfully prepared as a solid catalyst for UV-Fenton to degrade non-biodegradable azo-dye Orange II. Compared with raw bentonite, the content of iron, interlamellar distance and external surface area of H-Fe-P-B increased remarkably. H-Fe-P-B had good photosensitivity and catalyst reactivity. And the catalytic activity of H-Fe-P-B for H(2)O(2) came from hydroxyl-Fe between sheets rather than Fe(3+) or Fe(2+) in tetrahedral or octahedral sheets of bentonite. In UVA-H(2)O(2) system, H(2)O(2) could destroy the azo bond of excited Orange II molecules but could not effectively mineralize it. After 120 min treatment, 83% discoloration was obtained while only 2% of TOC was removed. When H-Fe-P-B was used as catalyst, a significant degradation of Orange II was observed at the same condition as UVA-H(2)O(2) system. Almost 100% discoloration and more than 60% TOC removal of Orange II could be achieved after 120 min treatment. Because of the strong surface acidity and the electronegativity of H-Fe-P-B, the pH range of this catalyst in the Orange II discoloration could be extended up to 9.5. And this catalyst showed good stability during Orange II degradation in water in wide range of pH (3.0-9.5). These results indicated that the H-Fe-P-B was a promising catalyst for UV-Fenton system.     

Chemical oxidative degradation of methyl tert-butyl ether in aqueous solution by Fenton's reagent

Degradation of methyl tert-butyl ether (MTBE) in aqueous solution by Fenton's reagent (Fe2+ and H2O2) was investigated. Effects of reaction conditions on the oxidation efficiency of MTBE by Fenton's reagent were examined in batch experiments. Under optimum conditions, 15 mM H2O2, 2 mM Fe2+, pH 2.8 and room temperature, the initial 1 mM MTBE solution was reduced by 99% within 120 min. Results showed that MTBE was decomposed in a two-stage reaction. MTBE was first decomposed swiftly based on a Fe2+/H2O2 reaction and then decomposed somewhat less rapidly based on a Fe3+/H2O2 reaction. The detection of Fe2+ also supported the theory of the two-stage reaction for the oxidation of MTBE by Fenton's reagent. The dissolved oxygen in the solution decreased rapidly in the first stage reaction, but it showed a slow increase in the second stage with a zero-order kinetics. A reaction mechanism involving two different pathways for the decomposition of MTBE by Fenton's reagent was also proposed. Chemicals including tert-butyl formate, tert-butyl alcohol, methyl acetate and acetone were identified to be the primary intermediates and by-products of the degradation processes.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

An assessment of the suitable operating conditions for the CeO2/gamma-Al2O3 catalyzed wet air oxidation of phenol

It has been shown that the CeO2/gamma-Al2O3 catalyst is a feasible alternative to CeO2 for the catalytic wet air oxidation (CWAO) of phenol because it remains an effective catalyst and yet is cheaper to prepare. In this study, we found that the optimal cerium content in the CeO2/gamma-Al2O3 catalyst was 20 wt.%, regardless of catalyst loading. Furthermore, at 180 degrees C, with a phenol concentration of 1000 mg l(-1), and an O2 partial pressure of 1.0M Pa or 1.5M Pa, the optimal catalyst loading was 3.0 gl (-1). The efficacy of CWAO of phenol improved with O2 partial pressure, although the effects of O2 pressure were more significant between 0.5 MPa and 1.5 MPa than between 1.5 MPa and 2.0 MPa. After 2 h of reaction, approximately 100% phenol conversion and 80% total organic carbon (TOC) removal was recorded at 180 degrees C, 1000 mg l(-1) of phenol and 3.0 g l(-1) of catalyst. Because these percentages subsequently leveled off, it is suggested that 2 h is a suitable time over which to run the reaction. The efficacy of CWAO of phenol decreased as initial phenol concentration was raised (from 400 to 2500 mg l(-1)), with the exception of phenol conversion after about 2 h, for which 400 mg l(-1) produced the lowest phenol conversion figure. Higher phenol concentrations require both catalyst loading and O2 partial pressure to be increased to maintain high performance. For example, for 2000 mg l(-1) and 2500 mg l(-1) phenol, nearly 100% phenol conversion and 90% TOC removal after 4 h of reaction at 180 degrees C required 4.0 g l(-1) of catalyst and 2.0 MPa.     

Aniline degradation by Electro-Fenton and peroxi-coagulation processes using a flow reactor for wastewater treatment

The degradation of 10-30 l of a 1000 ppm aniline solution in 0.050 M Na2SO4 + H2SO4 at pH 3.0 and 40 degrees C by Electro-Fenton and peroxi-coagulation processes at constant current until 20 A has been studied using a pilot flow reactor in recirculation mode with a filter-press cell containing an anode and an oxygen diffusion cathode, both of 100 cm2 area. H2O2 is produced by the two-electron reduction of O2 at the cathode, being accumulated with a current efficiency between 60% and 80% at the first stages of electrolyses performed with a Ti/Pt anode. In the presence of 1 mM Fe2+, less H2O2 is accumulated, but it is not detected using an Fe anode. The Electro-Fenton process with 1 mM Fe2+ and a Ti/Pt or DSA anode yields an insoluble violet polymer, while the soluble total organic carbon (TOC) is gradually removed, reaching 61% degradation after 2 h at 20 A. In this treatment, pollutants are preferentially oxidized by hydroxyl radicals formed in solution from reaction of Fe2+ with H2O2. The peroxi-coagulation process with an Fe anode has higher degradation power, allowing to remove more than 95% of pollutants at 20 A, since some intermediates coagulate with the Fe(OH)3 precipitate formed. Both advanced electrochemical oxidation processes (AEOPs) show moderate energy costs, which increase with increasing electrolysis time and applied current.     

Practical applications of the fenton reaction to the removal of chlorinated aromatic pollutants

BACKGROUND: Chlorophenols (CPs) constitute a group of organic pollutants that are introduced into the environment as a result of several man-made activities, such as uncontrolled use of pesticides and herbicides, and as byproducts in the paper pulp bleaching. Promising removal technologies of chlorinated aromatics consist in the application of advanced oxidation processes (AOPs) that can provide an almost total degradation of a variety of contaminants. Among these, wide application find Fenton systems based on generation of reactive species having a high oxidizing power, such as hydroxyl radical HO*. Our objective was that of determining the overall degradation efficiency of the model compound 2,4-dichlorophenol (DCP) by thermal Fenton-type oxidation systems with a view toward defining in more details relevant process parameters, the effect of reaction temperature and of co-catalyst Cu2+. METHODS: Reaction conditions were similar to those generally adopted as optimal in many practical applications, i.e. pollutant/Fe2+ (as FeSO4) ratio ca. 20, Fe2+/Cu2+ (co-catalyst) 2:1, pH adjusted and controlled at pH 3, and H2O2 in excess (up to four-fold over the stoichiometric amount required for complete mineralization). RESULTS AND DISCUSSION: The results demonstrate that it is advantageous to carry out the reaction at a temperature markedly higher (70 degrees C) than ambient. The stepwise addition of H2O2 in aliquots yields an efficient transformation, while allowing a convenient control of the reaction exothermicity. Under these conditions, the essentially complete removal of the initial DCP is accomplished using just one equiv of H2O2 during 15 min; excess H2O2 (5 equivalents) yields extensive substrate mineralization. Also relevant, at 70 degrees C dechlorination of the initial DCP (and of derived reaction intermediates) is remarkably extensive (3-5% residual TOX), already with the addition of 1 equiv of H2O2. At the end of the reaction, IC and IC-MS analyses of the solution reveal that only low-molecular weight carboxylic acid (acetic, formic, oxalic, malonic, tartaric, etc.) contribute to the residual TOC. CONCLUSIONS: The whole of the results herein point to the advantage of performing the process at temperatures substantially higher than ambient (70 degrees C). Under the conditions adopted, almost complete degradation of the initial toxic compound can be achieved using hydrogen peroxide in fair excess (e.g., 3.5 equiv H2O2). RECOMMENDATIONS AND OUTLOOK: In applying practical Fenton-type degradation systems to heavily polluted wastes, either for the pre-treatment of waters with a high COD value prior to biodegradation or for complete mineralization of pollutants, the set up of appropriate reaction conditions appears to be a key factor. Also, it is desirable to keep the concentration of iron salts within the lower limits in order to minimize the production and disposal of iron oxide sludges.