水中萘普生的紫外光降解机制及其产物毒性研究

以120 W汞灯为紫外光光源,通过活性氧物种(ROS)的淬灭实验和溶解氧(DO)浓度实验和发光菌毒性实验,对水中萘普生(NPX)的降解机制、反应动力学及其产物毒性进行了研究.结果表明,NPX的紫外光降解过程包括了直接光解和ROS参与的自敏化光解两个过程,同时.OH、1O2、O.2-的自敏化光解贡献率分别为0.1%、80.2%、35.7%;溶解氧浓度实验表明,溶解氧对萘普生的降解具有抑制作用,而且浓度越大,抑制效果越明显;发光菌毒性实验表明,萘普生光降解生成了具有较萘普生更高风险的中间产物.本研究中萘普生的所有光解实验过程均符合准一级动力学方程.     

TiO2复合催化剂弱光催化降解模拟海水中苯酚及其催化活性的影响

为了获得适用于海水中有机污染物光降解催化剂,分别选用纳米SiO_2粒子和氧化石墨烯GO为载体,利用吸附相反应技术并结合热处理过程制备了基于TiO_2的复合催化剂,研究了弱光(光强小于1mW·cm~(-3))激发下复合催化剂光催化降解模拟海水中苯酚.结果表明,吸附相反应技术结合焙烧得到的La~(3+)掺杂TiO_2-SiO_2,表面亲水性较强和对苯酚吸附能力较弱,难以克服盐离子的干扰并有效降解模拟海水中高浓度苯酚.而吸附相反应技术结合醇溶剂热还原处理后,La~(3+)掺杂TiO_2-SiO_2催化剂表面亲水性显著减弱,但该催化剂在模拟海水中不能形成稳定的悬浮体系.吸附相反应技术得到的TiO_2-GO和La~(3+)掺杂TiO_2-GO中,TiO_2粒子粒径小于10nm且均匀负载于GO的表面.醇溶剂热还原处理可使TiO_2形成晶型结构,从而提高其催化活性,同时还能将GO表面的含氧基团还原,降低催化剂表面亲水性.从而提升催化剂对苯酚的吸附能力和对盐离子的抗干扰能力.另外,还原GO与小粒径TiO_2粒子紧密结合,使光生电子能很快转移至还原GO表面,增大光生电荷分离率,进一步提升催化剂的光降解性能.     

TiO2诱导下左旋氧氟沙星的可见光降解及其机制

左旋氧氟沙星是一种新型污染物.单一的左旋氧氟沙星(LFV)和Ti O2无可见光响应,但二者共存下左旋氧氟沙星能发生显著的可见光降解.为此研究Ti O2用量、溶液p H以及左旋氧氟沙星浓度对Ti O2/Vis(可见光)降解左旋氧氟沙星的影响及机制.结果表明,左旋氧氟沙星能吸附在Ti O2表面,吸附服从准二级吸附动力学和Langmuir吸附等温线.吸附左旋氧氟沙星的Ti O2漫反射UV-Vis光谱进一步表明二者形成表面复合物.左旋氧氟沙星的Ti O2/Vis降解动力学符合LangmuirHinshelwood方程.合适的Ti O2浓度和中性p H有利于光解过程的进行.自由抑制实验、N2保护下左旋氧氟沙星的Ti O2/Vis降解实验揭示·O-2是该过程中的主要活性物种.同时,无氧左旋氧氟沙星-Ti O2悬浮液光照不同时间的UV-Vis光谱证明体系中存在电子向Ti O2导带的注入.依据实验结果提出吸附在Ti O2表面的左旋氧氟沙星与Ti O2形成表面复合物,在可见光照下发生电子迁移,从而引发左旋氧氟沙星降解.本研究表明利用污染与Ti O2形成表面复合物诱导其可见光降解可用来去除水中某些有机污染物.     

Fabrication of Bi2O3/TiO2 nanocomposites and their applications to the degradation of pollutants in air and water under visible-light

A nanoheterojunction composite photocatalyst Bi2O3/TiO2working under visible-light(λ 420 nm) was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.     

玻璃载体TiO2薄层光催化降解久效磷农药

研究了利用TiO₂薄层光催化降解久效磷农药的可行性。结果表明,0.65×10-4mol/L的久效磷经375W中压汞灯照射60min,被完全光催化降解至PO₄3-;加入微量的Fe3++或H2O2可提高久效磷农药的光解率;另外还研究了TiO₂薄层的附着量、反应液初始pH值、空气流量等因素对光催化降解的影响。光照80 h,TiO₂的光催化活性没有减弱,可连续使用。      

WC/TiO2纳米复合界面光催化剂制备及其光催化降解酚类污染物研究

设计并制备了新型WC/TiO2纳米复合界面光催化剂应用于酚类污染物的光催化降解反应中.采用X射线衍射(XRD)和扫描电子显微镜(SEM)技术分析了WC/TiO2纳米复合界面光催化剂的晶型和表面形貌.结果显示锐钛矿型TiO2纳米颗粒均匀地分散在WC纳米球表面并很好地构筑了WC/TiO2界面.研究了不同WC负载比例的WC/TiO2光催化剂在模拟太阳光照射下降解苯酚的光催化性能.结果表明:WC/TiO2复合界面的形成可以有效地提高TiO2光催化降解性能;其中,3%WC/TiO2(质量分数)光催化降解苯酚的活性最高.利用紫外-可见光谱(UV-Vis)和高效液相色谱-质谱联用技术(HPLC-MS)分析了WC/TiO2纳米复合界面光催化剂降解苯酚的中间产物,提出了苯酚在WC/TiO2界面上可能的降解机理.     

氧化剂增强TiO2纤维光催化降解DMF研究

研究TiO₂纤维光催化降解DMF水溶液的结果表明:氧化剂增强了TiO₂纤维对DMF的降解能力,在其它反应条件相同情况下,O₃/TiO₂(F)对DMF降解率是air/TiO₂(F)和H₂O₂/TiO₂(F)的1.5倍左右,且降解速率提高2倍左右,COD分析表明DMF几乎完全矿化.同时实验过程中确定了DMF光催化降解中间产物仲胺的存在.以二甲胺为仲胺代表物进行光催化降解研究表明,中间产物仲胺的迅速降解是O₃增强TiO₂纤维降解效应的主要因素.     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

水中普萘洛尔的紫外光降解机制及其产物毒性

以高压汞灯为光源,研究了紫外光照条件下水中普萘洛尔(PRO)的光解行为、机制及安全性.PRO光解机制通过活性氧物种(ROS)猝灭实验来确定,光解产物安全性通过发光菌毒性实验来评价.结果表明,PRO的光解速率常数(k)随初始浓度的增加而下降,两者呈显著负相关关系(r2>0.95).随着溶液初始pH的升高,PRO的光解加快,pH 5~9的PRO溶液的k值为0.0953~0.267 min-1.ROS猝灭实验表明,PRO的紫外光解过程包括了激发三重态PRO(3PRO*)参与的直接光解,以及羟基自由基(·OH)和单线态氧(1O2)参与的自敏化光解,直接光解速率常数大于自敏化光解速率常数.采用FFA探针方法测定了不同实验条件下1O2的浓度,其总体变化规律与猝灭实验所得结论一致.发光菌毒性实验表明,PRO光解生成了比母体化合物毒性更强的中间产物.     

Synthesis,crystal structure,photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c = 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^− 1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2 − and NO₃⁻, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography–mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.     

微波改性MWNTs/TiO2复合材料对1,2,3-三氯苯的光催化降解研究

在微波辐照干化的条件下用溶胶-凝胶法制备了MWNTs/TiO2复合光催化剂.对该复合材料的表征表明：随着微波功率逐渐增大至400 W,MWNTs/TiO2复合材料管径逐渐变小,且在400 W时制备的MWNTs/TiO2复合材料分散性较好.进一步增大微波功率导致复合材料的管径增大,分散性降低.研究了不同微波辐照条件下制备的MWNTs/TiO2复合光催化剂对1,2,3-三氯苯的光催化降解效果,结果表明,该复合光催化剂对1,2,3-三氯苯的光降解遵循一级反应动力学;在微波功率为400 W、辐照时间为5 min情况下制备的复合光催化剂对1,2,3-三氯苯的降解速率最快,其反应常数为0.023 7 min^-1,该值比非微波加热干化的同样复合材料的反应速率常数值提高了52%.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds (VOCs) in indoor air. Heterogeneous TiO₂-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline TiO₂ with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO₃. The obtained samples were characterized by X-ray diffraction and N₂ adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline TiO₂ exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline TiO₂, due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline TiO₂ prepared at R_HNO3 = 0.8, containing 80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity, about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline TiO₂ will enrich the chemistry of the TiO₂-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.     

Surface modification of polypropylene non-woven fibers with TiO2 nanoparticles via layer-by-layer self assembly method: Preparation and photocatalytic activity

Polypropylene (PP) meltblown fibers were coated with titanium dioxide (TiO₂) nanoparticles using layer-by-layer (LbL) deposition technique. The fibers were first modified with 3 layers of poly(4-styrenesulfonic acid) (PSS) and poly(diallyl-dimethylammonium chloride) (PDADMAC) to improve the anchoring of the TiO₂ nanoparticle clusters. PDADMAC, which is positively charged, was then used as counter polyelectrolyte in tandem with anionic TiO₂ nanoparticles to construct TiO₂/PDADMAC bilayer in the LbL fashion. The number of deposited TiO₂/PDADMAC layers was varied from 1 to 7 bilayer, and could be used to adjust TiO₂ loading. The LbL technique showed higher TiO₂ loading efficiency than the impregnation approach. The modified fibers were tested for their photocatalytic activity against a model dye, Methylene Blue (MB). Results showed that the TiO₂ modified fibers exhibited excellent photocatalytic activity efficiency similar to that of TiO₂ powder dispersed in solution. The deposition of TiO₂ 3 bilayer on the PP substrate was sufficient to produce nanocomposite fibers that could bleach the MB solution in less than 4 hr. TiO₂-LbL constructions also preserved TiO₂ adhesion on substrate surface after 1 cycle of photocatalytic test. Successive photocatalytic test showed decline in MB reduction rate with loss of TiO₂ particles from the substrate outer surface. However, even in the third cycle, the TiO₂ modified fibers are still moderately effective as it could remove more than 95% of MB after 8 hr of treatment.     

Photocatalytic degradation of phenanthrene on soil surfaces in the presence of nanometer anatase TiO2 under UV-light

The effect of nanometer anatase TiO₂ was investigated on the photocatalytic degradation of phenanthrene on soil surfaces under a variety of conditions. After being spiked with phenanthrene, soil samples loaded with different amounts of TiO₂ (0 wt.%, 1 wt.%, 2 wt.%, 3 wt.%, and 4 wt.%) were exposed to UV-light irradiation for 25 hr. The results indicated that the photocatalytic degradation of phenanthrene followed the pseudo first-order kinetics. TiO₂ significantly accelerated the degradation of phenanthrene with the half-life reduced from 45.90 to 31.36 hr for TiO₂ loading of 0 wt.% and 4 wt.%, respectively. In addition, the effects of H₂O₂, light intensity and humic acid on the degradation of phenanthrene were investigated. The degradation of phenanthrene increased with the concentration of H₂O₂, light intensity and the concentration of humic acids. It has been demonstrated that the photocatalytic method in the presence of nanometer anatase TiO₂ was a very promising technology for the treatments of soil polluted with organic substances in the future.     

Synergistic photocatalytic degradation of pyridine using precious metal supported TiO2 with KBrO3

A series of precious metals catalysts （M/TiO/, M = Ru, Rh, Pd, Ag, Ir, Pt or Au） were prepared by a light deposition method and the synergistic photocatalytic degradations of pyridine （20 mg/L） under UV irradiation （365 nm） using M/TiO2 with electron capture agent KBrO3 have been investigated. The results show that KBrO3 has a greatly synergistic role on M/TiO2 and the photocatalytic activity of M/TiO2 is closely related to its work function. Ag could greatly enhance the activity of TiO2 due to the binding characteristics of pyridine on Ag. Under the conditions of 0.5 wt.% Ag loading, Ag/TiO2 concentration of 0.1 g/L, KlrO3 concentration of 10 mmol/L and reaction liquid pH value at 9, the pyridine can be degraded by 64% within 3 hr, doubled than TiO2 photocatalytic system. The degradation kinetics of pyridine follows first-order kinetics and k = 5.53 × 10-3 min^-1.     

附载TiO2光催化降解咪蚜胺农药

以主波长３６５ｎｍ的黑炽荧光灯为光源,研究了由ＣＭＣ－Ｎａ附载ＴｉＯ２光催化降解咪蚜胺农药的过程。结果表明,咪蚜胺农药在３＊８Ｗ黑炽荧光灯照射下,经附载ＴｉＯ２作用３ｈ后可降解５０％以上,其光解可用假一级动力学方程表示。     

紫外驱动高级氧化法降解水体中的磷酸三苯酯

有机磷酸酯（OPEs）作为备受关注的一类新污染物,已对偏远的南极地区水环境引发了中等风险.磷酸三苯酯（TPHP）是水体中常见的OPEs,已被证实具有毒性效应、生物富集和放大效应,对环境和人体健康威胁较大.利用傅里叶红外光谱仪（FT-IR）和液相色谱-串联质谱联用仪（LC-MS/MS）探究TPHP在紫外-过氧化氢（UV-H₂ O₂）、紫外-二氧化钛（UV-TiO₂）和紫外-过硫酸盐（UV-PS）这3种高级氧化体系（UV-AOPs）中的降解过程,创新性地利用FT-IR实现了TPHP降解过程中红外特征峰变化的在线观测,并对其降解反应动力学、光降解产物和降解路径进行了分析.结果表明,TPHP在UV-H₂ O₂、UV-TiO₂和UV-PS体系下均能得到有效降解,其光降解半衰期分别为74、150和89 min.其中,UV-H₂ O₂体系对TPHP的降解效果最好.TPHP在3种体系下的降解反应均符合一级动力学.当H₂ O₂浓度为0~0.097 mol ·L^-1时,H₂ O₂浓度升高会促进TPHP降解;当TiO₂浓度为0~0.013 mol ·L^-1时,TiO₂浓度升高会促进TPHP降解.TPHP的光降解路径主要是P—O—C键断裂、苯环结构的C—H键断裂和水解反应.利用UV-H₂ O₂体系对成都市环境水体中OPEs进行降解实验,发现对公园景观水体的水样进行降解反应60 min时,TPHP的去除率为66%.     

Photodegradation of soluble microbial products (SMPs) from membrane bioreactor by GO-COOH/TiO2/Ag

This study aimed to explore a new degradation method - photocatalysis technology to polish membrane bioreactor (MBR) effluent, using 2,6-di-tert-butylphenol (2,6-DTBP) as a model soluble microbial product (SMP). 2,6-DTBP is one of the predominant SMPs in MBR effluent, which is refractory and difficult to biodegrade. This study developed a novel carboxylated graphene oxide/titanium dioxide/silver (GO-COOH/TiO₂/Ag) nanocomposite to photodegrade 2,6-DTBP. GO-COOH/TiO₂/Ag was successfully synthesized, using l-cysteine as the linker bonding TiO₂/Ag to GO-COOH. The structural, morphological and optical properties of the GO-COOH/TiO₂/Ag nanocomposite were characterized using various techniques. Owing to synergistic effects, the GO-COOH/TiO₂/Ag nanocomposite exhibited enhanced photocatalytic degradation performance under solar light irradiation when compared to TiO₂, Ag and GO-COOH. To remove 25 mg/L 2,6-DTBP, the reaction time for GO-COOH/TiO₂/Ag was only 30 min, faster than the 90 min required for pure TiO₂ or Ag. In addition, the 200 mg/L GO-COOH/TiO₂/Ag nanocomposite aqueous solution showed the best performance under solar light, with 99% removal of 2,6-DTBP. This enhanced capability is likely due to the surface plasmon resonance (SPR) effect contributed by Ag nanoparticles (NPs) doped onto the TiO₂. In addition, GO-COOH had a high effective surface area, which assisted in degrading the 2,6-DTBP through improved adsorption. The stability study showed that the photocatalytic activity of the GO-COOH/TiO₂/Ag was stable enough for recycling multiple times. The effective degradation performance and excellent stability demonstrates that the GO-COOH/TiO₂/Ag nanocomposite can be a promising photocatalyst in the field of effluent SMP photodegradation, which solves the problem of the difficult biodegradation of highly toxic 2,6-DTBP.     

Synthesis, crystal structure, photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c= 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^-1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2- and NO₃^-, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography- mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds(VOCs) in indoor air. Heterogeneous Ti O_2-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline Ti O_2 with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO_3.The obtained samples were characterized by X-ray diffraction and N_2 adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline Ti O_2 exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline Ti O_2,due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline Ti O_2 prepared at R HNO_3= 0.8, containing80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity,about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline Ti O_2 will enrich the chemistry of the Ti O_2-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.