Outdoor fine and ultrafine particle measurements at six bus stops with smoking on two California arterial highways—Results of a pilot study

As indoor smoking bans have become widely adopted, some U.S. communities are considering restricting smoking outdoors, creating a need for measurements of air pollution near smokers outdoors. Personal exposure experiments were conducted with four to five participants at six sidewalk bus stops located 1.5–3.3 m from the curb of two heavily traveled California arterial highways with 3300–5100 vehicles per hour. At each bus stop, a smoker in the group smoked a cigarette. Gravimetrically calibrated continuous monitors were used to measure fine particle concentrations (aerodynamic diameter ≤2.5 µm; PM_2.5) in the breathing zones (within 0.2 m from the nose and mouth) of each participant. At each bus stop, ultrafine particles (UFP), wind speed, temperature, relative humidity, and traffic counts were also measured. For 13 cigarette experiments, the mean PM_2.5 personal exposure of the nonsmoker seated 0.5 m from the smoker during a 5-min cigarette ranged from 15 to 153 µg/m³. Of four persons seated on the bench, the smoker received the highest PM_2.5 breathing-zone exposure of 192 µg/m³. There was a strong proximity effect: nonsmokers at distances 0.5, 1.0, and 1.5 m from the smoker received mean PM_2.5 personal exposures of 59, 40, and 28 µg/m³, respectively, compared with a background level of 1.7 µg/m³. Like the PM_2.5 concentrations, UFP concentrations measured 0.5 m from the smoker increased abruptly when a cigarette started and decreased when the cigarette ended, averaging 44,500 particles/cm³ compared with the background level of 7200 particles/cm³. During nonsmoking periods, the UFP background concentrations showed occasional peaks due to traffic, whereas PM_2.5 background concentrations were extremely low. The results indicate that a single cigarette smoked outdoors at a bus stop can cause PM_2.5 and UFP concentrations near the smoker that are 16–35 and 6.2 times, respectively, higher than the background concentrations due to cars and trucks on an adjacent arterial highway.

Implications: Rules banning smoking indoors have been widely adopted in the United States and in many countries. Some communities are considering smoking bans that would apply to outdoor locations. Although many measurements are available of pollutant concentrations from secondhand smoke at indoor locations, few measurements are available of exposure to secondhand smoke outdoors. This study provides new data on exposure to fine and ultrafine particles from secondhand smoke near a smoker outdoors. The levels are compared with the exposure measured next to a highway. The findings are important for policies that might be developed for reducing exposure to secondhand smoke outdoors.     

Influence of tobacco smoke on carcinogenic PAH composition in indoor PM10 and PM2.5

Because of the mutagenic and/or carcinogenic properties, Polycyclic Aromatic Hydrocarbons (PAH), have a direct impact on human population. Consequently, there is a widespread interest in analysing and evaluating the exposure to PAH in different indoor environments, influenced by different emission sources. The information on indoor PAH is still limited, mainly in terms of PAH distribution in indoor particles of different sizes; thus, this study evaluated the influence of tobacco smoke on PM₁₀ and PM_2.5 characteristics, namely on their PAH compositions, with further aim to understand the negative impact of tobacco smoke on human health. Samples were collected at one site influenced by tobacco smoke and at one reference (non-smoking) site using low-volume samplers; the analyses of 17 PAH were performed by Microwave Assisted Extraction combined with Liquid Chromatography (MAE–LC). At the site influenced by tobacco smoke PM concentrations were higher 650% for PM₁₀, and 720% for PM_2.5. When influenced by smoking, 4 ring PAH (fluoranthene, pyrene, and chrysene) were the most abundant PAH, with concentrations 4600–21 000% and 5100–20 800% higher than at the reference site for PM₁₀ and PM_2.5, respectively, accounting for 49% of total PAH (Σ_PAH). Higher molecular weight PAH (5–6 rings) reached concentrations 300–1300% and 140–1700% higher for PM₁₀ and PM_2.5, respectively, at the site influenced by tobacco smoke. Considering 9 carcinogenic PAH this increase was 780% and 760% in PM₁₀ and PM_2.5, respectively, indicating the strong potential risk for human health. As different composition profiles of PAH in indoor PM were obtained for reference and smoking sites, those 9 carcinogens represented at the reference site 84% and 86% of Σ_PAH in PM₁₀ and PM_2.5, respectively, and at the smoking site 56% and 55% of Σ_PAH in PM₁₀ and PM_2.5, respectively. All PAH (including the carcinogenic ones) were mainly present in fine particles, which corresponds to a strong risk for cardiopulmonary disease and lung cancer; thus, these conclusions are relevant for the development of strategies to protect public health.     

Size-segregated particulate matter and its association with respiratory deposition doses among outdoor exercisers in Dhanbad City,India

Regular exercise improves physiological processes and yields positive health outcomes. However, it is relatively less known that particulate matter (PM) exposure during outdoor exercises may increase several respiratory health problems depending on PM levels. In this study, the respiratory deposition doses (RDDs) in head airway (HD), tracheobronchial (TB), and alveolar (AL) regions of various PM size fractions (<10, <2.5, and <1 μm; PM₁₀, PM_2.5, and PM₁) were estimated in healthy male and female exercisers in urban outdoors and within house premises. The highest RDDs were found for PM during morning hours in winter compared with remaining periods. RDDs in AL region for males and females, respectively, were 34.7 × 10^?2 and 28.8 × 10^?2 µg min^?1 for PM₁₀, 65.7 × 10^?2 and 56.9 × 10^?2 µg min^?1 for PM_2.5, and 76.5 × 10^?2 and 66.3 × 10^?2 µg min^?1 for PM₁. The RDD values in AL region were significantly higher in PM₁ (27%) compared with PM_2.5 (13%) and PM₁₀ (2%) during exercise in all periods. This result showed that the morning peak hours in winter are more harmful to urban outdoor exercisers compared with other periods. This study also showed that the AL region would have been the main affected zone through fine particle (PM₁) to all the exercisers.

Implications: Size-segregated particle concentrations in urban outdoors and within house premises were measured. The highest respiratory deposition doses (RDDs) were found for PM during morning hours in winter compared with remaining periods. During light exercise, the RDD values in alveolar (AL) region for PM₁₀, PM_2.5, and PM₁ for male exercisers were significantly higher, 20.4%, 15.5%, and 15.4%, respectively, compared with female exercisers during morning peak hours in winter.     

Feasibility of using low-cost portable particle monitors for measurement of fine and coarse particulate matter in urban ambient air

Exposure to ambient particulate matter (PM) is known as a significant risk factor for mortality and morbidity due to cardiorespiratory causes. Owing to increased interest in assessing personal and community exposures to PM, we evaluated the feasibility of employing a low-cost portable direct-reading instrument for measurement of ambient air PM exposure. A Dylos DC 1700 PM sensor was collocated with a Grimm 11-R in an urban residential area of Houston Texas. The 1-min averages of particle number concentrations for sizes between 0.5 and 2.5 µm (small size) and sizes larger than 2.5 µm (large size) from a DC 1700 were compared with the 1-min averages of PM_2.5 (aerodynamic size less than 2.5 µm) and coarse PM (aerodynamic size between 2.5 and 10 µm) concentrations from a Grimm 11-R. We used a linear regression equation to convert DC 1700 number concentrations to mass concentrations, utilizing measurements from the Grimm 11-R. The estimated average DC 1700 PM_2.5 concentration (13.2 ± 13.7 µg/m³) was similar to the average measured Grimm 11-R PM_2.5 concentration (11.3 ± 15.1 µg/m³). The overall correlation (r²) for PM_2.5 between the DC 1700 and Grimm 11-R was 0.778. The estimated average coarse PM concentration from the DC 1700 (5.6 ± 12.1 µg/m³) was also similar to that measured with the Grimm 11-R (4.8 ± 16.5 µg/m³) with an r² of 0.481. The effects of relative humidity and particle size on the association between the DC 1700 and the Grimm 11-R results were also examined. The calculated PM mass concentrations from the DC 1700 were close to those measured with the Grimm 11-R when relative humidity was less than 60% for both PM_2.5 and coarse PM. Particle size distribution was more important for the association of coarse PM between the DC 1700 and Grimm 11-R than it was for PM_2.5.

Implications: The performance of a low-cost particulate matter (PM) sensor was evaluated in an urban residential area. Both PM_2.5 and coarse PM (PM_10-2.5) mass concentrations were estimated using a DC1700 PM sensor. The calculated PM mass concentrations from the number concentrations of DC 1700 were close to those measured with the Grimm 11-R when relative humidity was less than 60% for both PM_2.5 and coarse PM. Particle size distribution was more important for the association of coarse PM between the DC 1700 and Grimm 11-R than it was for PM_2.5.     

Influence of tobacco smoke on the elemental composition of indoor particles of different sizes

Tobacco smoking is one of the greatest sources of indoor inhalable (PM₁₀) particles. In the past, the studies conducted on indoor particulates were mostly related to PM₁₀, however in the last decade respirable particles (PM_2.5) and even smaller particles (PM₁) began to be more important as they penetrate deeper in the respiratory system, causing severe health effects. Therefore, more information on fine particles is needed. Aiming to evaluate the impact of tobacco smoke on public health, this work evaluates the influence of tobacco smoke on the characteristics of PM₁₀, PM_2.5, and PM₁ considering concentration and elemental composition. Samples were collected at sites influenced by tobacco smoke, as well as at reference sites, using low-volume samplers; the element analyses were performed by proton induced X-ray emission (PIXE); Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Cd, I, Ba, La, Ce and Pb were quantified. At the sites influenced by tobacco smoke concentrations were 270–560% higher for PM₁₀ and 320–680% higher for PM_2.5 than at reference sites. Tobacco smoke increased the total concentrations of five carcinogenic elements (Cr, Ni, As, Cd and Pb) 1100–2400% for PM₁₀ and 840–2200% for PM_2.5. The elements associated with tobacco smoke (S, K, Cr, Ni, Zn, As, Cd and Pb) were predominantly present in the fine fraction; the elements mostly originating from building erosion (Mg, Al, Si and Ca) predominantly occurred in the coarse particles. The analysis of enrichment factors confirmed that tobacco smoking mainly influenced the composition of the fine fraction of particles; as these smaller particles have a strong influence on health, these conclusions are relevant for the development of strategies to protect public health.     

DEARS particulate matter relationships for personal,indoor, outdoor,and central site settings for a general population

This analysis provides the initial summary of PM_2.5 mass concentrations relationships for all seasons and participants for a general population in the Detroit Exposure and Aerosol Research Study (DEARS). The summary presented highlights the utility of the new methodologies applied, in addition to summarizing the particulate matter (PM) data.Results include the requirement to adjust the exposure data for monitor wearing compliance and measured environmental tobacco smoke (ETS) levels, even though the study design specified a non-smoking household. A 40% wearing compliance acceptance level was suggested as necessary to balance minimizing exposure misclassification (from poor compliance) and having sufficient data to conduct robust statistical analyses. An ETS threshold level equivalent to adding more than 1.5 μg m^?3 to the collected sample was found to be necessary to detect changes in the personal exposure factor (F_pex). It is not completely clear why such a large threshold level was necessary.Statistically significant spatial PM_2.5 gradients were identified in three of the six DEARS neighborhoods in Wayne County. These were expected, given the number of strong, localized PM sources in the Detroit (Michigan) metro area. Some residential outdoor bias levels compared with the central site at Allen Park exceeded 15%. After adjusting for ETS biases, the outdoor contributions to the personal exposure were typically larger by factors from 1.75 to 2.2 compared with those of the non-outdoor sources. The outdoor contribution was larger in the summer than in the winter, which is consistent with the fractions of time spent outdoors in the summer vs. the winter (6.7% vs. 1.1% of the time).Mean personal PM_2.5 cloud levels for the general population DEARS cohort ranged from 1.5 to 3.8 (after ETS adjustment) and were comparable to those reported previously. The personal exposure collections indoors were typically at least 13 times greater than those contributed outdoors.     

Levels of outdoor PM2.5, absorbance and sulphur as surrogates for personal exposures among post-myocardial infarction patients in Barcelona,Spain

Outdoor levels of fine particles (PM_2.5; particles <2.5 μm) have been associated with cardiovascular health. Persons with existing cardiovascular disease have been suggested to be especially vulnerable. It is unclear, how well outdoor concentrations of PM_2.5 and its constituents measured at a central site reflect personal exposures in Southern European countries. The objective of the study was to assess the relationship between outdoor and personal concentrations of PM_2.5, absorbance and sulphur among post-myocardial infarction patients in Barcelona, Spain.Thirty-eight subjects carried personal PM_2.5 monitors for 24-h once a month (2–6 repeated measurements) between November 2003 and June 2004. PM_2.5 was measured also at a central outdoor monitoring site. Light absorbance (a proxy for elemental carbon) and sulphur content of filter samples were determined as markers of combustion originating and long-range transported PM_2.5, respectively.There were 110, 162 and 88 measurements of PM_2.5, absorbance and sulphur, respectively. Levels of outdoor PM_2.5 (median 17 μg m³) were lower than personal PM_2.5 even after excluding days with exposure to environmental tobacco smoke (ETS) (median after exclusion 27 μg m³). However, outdoor concentrations of absorbance and sulphur were similar to personal concentrations after exclusion of ETS. When repeated measurements were taken into account, there was a statistically significant association between personal and outdoor absorbance when adjusting for ETS (slope 0.66, p<0.001), but for PM_2.5 the association was weaker (slope 0.51, p=0.066). Adjustment for ETS had little effect on the respective association of S (slope 0.69, p<0.001).Our results suggest that outdoor measurements of absorbance and sulphur can be used to estimate both the daily variation and levels of personal exposures also in Southern European countries, especially when exposure to ETS has been taken into account. For PM_2.5, indoor sources need to be carefully considered.     

Improved Titrilog Sensitivity

ABSTRACT

A method was developed to reproducibly measure environmental tobacco smoke (ETS) components generated by different cigarettes. Measurements were carried out in an unventilated, controlled environment chamber. True ETS (the aged and diluted combination of exhaled mainstream plus sidestream smoke) was generated by human smokers. To reliably quantitate components normally present at trace levels, the comparisons were carried out at elevated ETS concentrations—greater than 40 times those typically encountered in “real-world” settings.

The method was applied to four commercially available cigarettes and a cigarette prototype that primarily heats tobacco. Forty-three properties and components of the gas and particulate phases of ETS generated by the different cigarettes were measured. Good precision of measurement was obtained both within and between tests. Statistically significant differences in the concentration of ETS components were observed among the different commercial cigarettes and between the commercial and prototype cigarettes. Most ETS components from the prototype cigarette were reduced by >90% when compared to the commercial cigarettes. The method was used to determine the effect of cigarette design changes on the generation of ETS.     

Atmospheric Particulate Matter and Polycyclic Aromatic Hydrocarbons for PM10 and Size-Segregated Samples in Bangkok

Abstract

Air samples of particulate matter (PM) with an aerodynamic diameter less than 10 µm (PM₁₀) were collected from six sites in Bangkok, Thailand, using high-volume air samplers. Daily samples were taken at intervals of 12 days from November 1999 to November 2000. Size-selected sampling using a multislit Andersen size-fractionated cascade impactor was undertaken at one site in central Bangkok to identify particulate size distribution. The annual average PM₁₀ concentration at all six sites exceeded the Thailand National Ambient Air Quality Standard (NAAQS) of 50 µg/m³. The daily PM₁₀ concentrations at heavy traffic roadside areas ranged between 30 and 160 µg/m³. The highest PM₁₀ level occurred during the winter period (November–February), which is the dry season. From our results, which are based on a 1-yr survey, it can be observed that the particulate concentrations are associated with traffic volumes and seasonal factors (temperature and rainfall). The relative importance of size fractions in contributing to PM load is presented and discussed. Twenty polycyclic aromatic hydro-carbons (PAHs) associated with PM have been identified and quantified. The summed PAHs based on the 20 species had an average concentration of 60 ng/m³. Benzo(e)pyrene, indeno(123cd)pyrene, and benzo(ghi)perylene were the major compounds with average concentrations of 8, 10, and 13 ng/m³, respectively. Results indicate that more than 97% of PAHs were found in the small particulate size range of <0.95 µm.     

Seasonal ambient particulate matter and population health outcomes among communities impacted by road dust in British Columbia,Canada

In recent years, many air quality monitoring programs have favored measurement of particles less than 2.5 µm (PM_2.5) over particles less than 10 µm (PM₁₀) in light of evidence that health impacts are mostly from the fine fraction. However, the coarse fraction (PM_10-2.5) may have independent health impacts that support continued measurement of PM₁₀ in some areas, such as those affected by road dust. The objective of this study was to evaluate the associations between different measures of daily PM exposure and two daily indicators of population health in seven communities in British Columbia, Canada, where road dust is an ongoing concern. The measures of exposure were PM₁₀, PM_2.5, PM_10-2.5, PM_2.5 adjusted for PM_10-2.5, and PM_10-2.5 adjusted for PM_2.5. The indicators of population health were dispensations of the respiratory reliever medication salbutamol sulfate and nonaccidental mortality. This study followed a time-series design using Poisson regression over a 2003–2015 study period, with analyses stratified by three seasons: residential woodsmoke in winter; road dust in spring; and wildfire smoke in summer. A random-effects meta-analysis was conducted to establish a pooled estimate. Overall, an interquartile range increase in daily PM_10-2.5 was associated with a 3.6% [1.6, 5.6] increase in nonaccidental mortality during the road dust season, which was reduced to 3.1% [0.8, 5.4] after adjustment for PM_2.5. The adjusted coarse fraction had no effect on salbutamol dispensations in any season. However, an interquartile range increase in PM_2.5 was associated with a 2.7% [2.0, 3.4] increase in dispensations during the wildfire season. These analyses suggest different impacts of different PM fractions by season, with a robust association between the coarse fraction and nonaccidental mortality in communities and periods affected by road dust. We recommend that PM₁₀ monitoring networks be maintained in these communities to provide feedback for future dust mitigation programs.

Implications: There was a significant association between daily concentrations of the coarse fraction and nonaccidental mortality during the road dust season, even after adjustment for the fine fraction. The acute and chronic health effects associated with exposure to the coarse fraction remain unclear, which supports the maintenance of PM₁₀ monitoring networks to allow for further research in communities affected by sources such as road dust.     

Characterization of Particulate Matter for Three Sites in Kuwait

Abstract

Many studies have shown strong associations between particulate matter (PM) levels and a variety of health outcomes, leading to changes in air quality standards in many regions, especially the United States and Europe. Kuwait, a desert country located on the Persian Gulf, has a large petroleum industry with associated industrial and urban land uses. It was marked by environmental destruction from the 1990 Iraqi invasion and subsequent oil fires. A detailed particle characterization study was conducted over 12 months in 2004–2005 at three sites simultaneously with an additional 6 months at one of the sites. Two sites were in urban areas (central and southern) and one in a remote desert location (northern). This paper reports the concentrations of particles less than 10 µm in diameter (PM₁₀) and fine PM (PM_2.5), as well as fine particle nitrate, sulfate, elemental carbon (EC), organic carbon (OC), and elements measured at the three sites. Mean annual concentrations for PM₁₀ ranged from 66 to 93 µg/m³ across the three sites, exceeding the World Health Organization (WHO) air quality guidelines for PM₁₀ of 20 µg/m³. The arithmetic mean PM_2.5 concentrations varied from 38 and 37 µg/m³ at the central and southern sites, respectively, to 31 µg/m³ at the northern site. All sites had mean PM_2.5 concentrations more than double the U.S. National Ambient Air Quality Standard (NAAQS) for PM_2.5. Coarse particles comprised 50–60% of PM₁₀. The high levels of PM₁₀ and large fraction of coarse particles comprising PM₁₀ are partially explained by the resuspension of dust and soil from the desert crust. However, EC, OC, and most of the elements were significantly higher at the urbanized sites, compared with the more remote northern site, indicating significant pollutant contributions from local mobile and stationary sources. The particulate levels in this study are high enough to generate substantial health impacts and present opportunities for improving public health by reducing airborne PM.     

Recent spatial gradients and time trends in Dhaka,Bangladesh, air pollution and their human health implications

Dhaka, the capital of Bangladesh, is among the most polluted cities in the world. This research evaluates seasonal patterns, day-of-week patterns, spatial gradients, and trends in PM_2.5 (<2.5 µm in aerodynamic diameter), PM₁₀ (<10 µm in aerodynamic diameter), and gaseous pollutants concentrations (SO₂, NO₂, CO, and O₃) monitored in Dhaka from 2013 to 2017. It expands on past work by considering multiple monitoring sites and air pollutants. Except for ozone, the average concentrations of these pollutants showed strong seasonal variation, with maximum during winter and minimum during monsoon, with the pollution concentration of PM_2.5 and PM₁₀ being roughly five- to sixfold higher during winter versus monsoon. Our comparisons of the pollutant concentrations with Bangladesh NAAQS and U.S. NAAQS limits analysis indicate particulate matter (PM_2.5 and PM₁₀) as the air pollutants of greatest concern, as they frequently exceeded the Bangladesh NAAQS and U.S. NAAQS, especially during nonmonsoon time. In contrast, gaseous pollutants reported far fewer exceedances throughout the study period. During the study period, the highest number of exceedances of NAAQS limits in Dhaka City (Darus-Salam site) were found for PM_2.5 (72% of total study days), followed by PM₁₀ (40% of total study days), O₃ (1.7% of total study days), SO₂ (0.38% of total study days), and CO (0.25% of total study days). The trend analyses results showed statistically significant positive slopes over time for SO₂ (5.6 ppb yr^?1, 95% confidence interval [CI]: 0.7, 10.5) and CO (0.32 ppm yr^?1, 95% CI: 0.01, 0.56), which suggest increase in brick kilns operation and high-sulfur diesel use. Though statistically nonsignificant annual decreasing slopes for PM_2.5 (?4.6 µg/m³ yr^?1, 95% CI: ?12.7, 3.6) and PM₁₀ (?2.7 µg/m³ yr^?1, 95% CI: ?7.9, 2.5) were observed during this study period, the PM_2.5 concentration is still too high (~ 82.0 µg/m³) and can cause severe impact on human health.

Implications: This study revealed key insights into air quality challenges across Dhaka, Bangladesh, indicating particulate matter (PM) as Dhaka’s most serious air pollutant threat to human health. The results of these analyses indicate that there is a need for immediate further investigations, and action based on those investigations, including the conduct local epidemiological PM exposure-human health effects studies for this city, in order to determine the most public health effective interventions.     

Monitoring an outdoor smoking area by means of PM<Subscript>2.5</Subscript> measurement and vegetal biomonitoring

The extension of pollutant accumulation in plant leaves associated with its genotoxicity is a common approach to predict the quality of outdoor environments. However, this approach has not been used to evaluate the environmental quality of outdoor smoking areas. This study aims to evaluate the effects of environmental tobacco smoke (ETS) by assessing particulate matter 2.5 μm (PM_2.5) levels, the pollen abortion assay, and trace elements accumulated in plant leaves in an outdoor smoking area of a hospital. For this, PM_2.5 was measured by active monitoring with a real time aerosol monitor for 10 days. Eugenia uniflora trees were used for pollen abortion and accumulated element assays. Accumulated elements were also assessed in Tradescantia pallida leaves. The median concentration of PM_2.5 in the smoking area in all days of monitoring was 66 versus 34 μg/m³ in the control area (P?<?0.001). In addition, the elements Al, Cd, Cu, Ni, Pb, Rb, Sb, Se, and V in Tradescantia pallida and Al, Ba, Cr, Cu, Fe, Mg, Pb, and Zn in Eugenia uniflora were in higher concentration in the smoking area when compared to control area. Smoking area also showed higher rate of aborted grains (26.1?±?10.7 %) compared with control (17.6?±?4.5 %) (P?=?0.003). Under the study conditions, vegetal biomonitoring proved to be an effective tool for assessing ETS exposure in outdoor areas. Therefore, vegetal biomonitoring of ETS could be a complement to conventional analyses and also proved to be a cheap and easy-handling tool to assess the risk of ETS exposure in outdoor areas.     

Physicochemical and toxicological characteristics of urban aerosols during a recent Indonesian biomass burning episode

Air particulate matter (PM) samples were collected in Singapore from 21 to 29 October 2010. During this time period, a severe regional smoke haze episode lasted for a few days (21–23 October). Physicochemical and toxicological characteristics of both haze and non-haze aerosols were evaluated. The average mass concentration of PM_2.5 (PM with aerodynamic diameter of ≤2.5 μm) increased by a factor of 4 during the smoke haze period (107.2 μg/m³) as compared to that during the non-smoke haze period (27.0 μg/m³). The PM_2.5 samples were analyzed for 16 priority polycyclic aromatic hydrocarbons (PAHs) listed by the United States Environmental Protection Agency and 10 transition metals. Out of the seven PAHs known as potential or suspected carcinogens, five were found in significantly higher levels in smoke haze aerosols as compared to those in the background air. Metal concentrations were also found to be higher in haze aerosols. Additionally, the toxicological profile of the PM_2.5 samples was evaluated using a human epithelial lung cell line (A549). Cell viability and death counts were measured after a direct exposure of PM_2.5 samples to A459 cells for a period of 48 h. The percentage of metabolically active cells decreased significantly following a direct exposure to PM samples collected during the haze period. To provide further insights into the toxicological characteristics of the aerosol particles, glutathione levels, as an indirect measure of oxidative stress and caspase-3/7 levels as a measure of apoptotic death, were also evaluated.     

Characterization of Particulate Matter in California

ABSTRACT

The size, composition, and concentration of particulate matter (PM) vary with location and time. Several monitoring/sampling programs are operated in California to characterize PM less than 2.5 and 10 µm in aerodynamic diameter (PM_2.5 and PM₁₀). This paper presents a broad summary of the spatial and temporal variations observed in ambient PM_2.5 and PM₁₀ concentrations in California. Many areas that have high PM₁₀ concentrations also have relatively high PM_2.5 concentrations, and data indicate that a significant portion of the PM₁₀ air quality problem is caused by PM_2.5. To develop effective plans for attaining the ambient PM standards, improved understanding of these unique problems is needed. Since 1989, pollution control efforts—whether specifically targeted for particulate matter or indirectly via controls on gaseous emissions—have caused annual average PM_2.5 and PM₁₀ concentrations to decline at most sites in California.     

Loading Effect Correction for Real-Time Aethalometer Measurements of Fresh Diesel Soot

Abstract

In this study, a correction was developed for the aethalometer to measure real-time black carbon (BC) concentrations in an environment dominated by fresh diesel soot. The relationship between the actual mass-specific absorption coefficient for BC and the BC-dependent attenuation coefficients was determined from experiments conducted in a diesel exposure chamber that provided constant concentrations of fine particulate matter (PM; PM_2.5; PM <2.5 µm in aerodynamic diameter) from diesel exhaust. The aethalometer reported BC concentrations decreasing with time from 48.1 to 31.5 µg m^?3when exposed to constant PM_2.5concentrations of 55 ± 1 µg m^?3and b_scat= 95 ± 3 Mm^?1from diesel exhaust. This apparent decrease in reported light-absorbing PM concentration was used to derive a correction K(ATN) for loading of strong light-absorbing particles onto or into the aethalometer filter tape, which was a function of attenuation of light at 880 nm by the embedded particles.     

Road Dust Resuspension in the Vicinity of Limestone Quarries in Jordan

Abstract

Many areas in Jordan suffer from elevated levels of coarse particulate matter (PM₁₀). One potentially significant source of the observed PM is the resuspension of road dust in the vicinity of limestone quarries. To obtain data to assess the impact from this source, PM₁₀ road dust resus-pension factors near Abusiiah, a town to the north east of Amman surrounded by many quarries and brick factories, were measured. Measurements included PM₁₀ mass, particle size distributions, wind speed, and wind direction.The results showed that PM₁₀ concentrations could be as high as 600 µg/m³, and most of the airborne PM is in the coarse fraction. Loading trucks play a major role in resus-pending road dust, with an observed PM₁₀ emission rate of >6000 mg/km.     

Development of a PM2 5 Emissions Inventory for the South Coast Air Basin

ABSTRACT

With the promulgation of a national PM_2.5 ambient air quality standard, it is important that PM_2.5 emissions inventories be developed as a tool for understanding the magnitude of potential PM2.5 violations. Current PM₁₀ inventories include only emissions of primary particulate matter (1 ^ï PM), whereas, based on ambient measurements, both PM₁₀ and PM2.5 emissions inventories will need to include sources of both 1^ï PM and secondary particulate matter (2^ï PM). Furthermore, the U. S. Environmental Protection Agency’s (EPA) current edition of AP-42 includes size distribution data for 1o PM that overestimate the PM_2.5 fraction of fugitive dust sources by at least a factor of 2 based on recent studies.

This paper presents a PM_2.5 emissions inventory developed for the South Coast Air Basin (SCAB) that for the first time includes both 1^ï PM and 2^ï PM. The former is calculated by multiplying PM₁₀ emissions estimates by the PM_2.5/PM₁₀ ratios for different sources. The latter is calculated from estimated emission rates of gas-phase aerosol precursor and gas to aerosol conversion rates consistent with the measured chemical composition of ambient PM_2.5 concentrations observed in the SCAB. The major finding of this PM_2.5 emissions inventory is that the ^2ï aerosol component is more than twice the ^1ï aerosol component, which may result in widely different control strategies being required for fine PM and coarse PM.     

Coarse Particulate Matter Apportionment around a Steel Smelter Plant

Abstract

The results from a study carried out in the urban area of Genoa, Italy, where a large steel smelter recently shut down are presented. We had the opportunity to sample particulate matter (PM) before and after plant closure and, therefore, to measure the changes in concentration and composition of PM₁₀ (atmospheric PM with aerodynamic diameter <10 µm). Elemental concentrations of Na to Pb were obtained through energy dispersive X-ray fluorescence (ED-XRF), and the contributions of specific sources of PM₁₀ were calculated by positive matrix factorization (PMF). The PM₁₀ average concentration turned out to be surprisingly similar before and after closing of the smelter. Nevertheless, the comparison among data collected in the two periods (plant operating and closed), even with the limited information provided by ED-XRF, allowed us to single out two sources of PM related to the smelter activities, to extract their emission profile, and to quantify the impact of the plant on PM₁₀ levels.     

A Federal Tax on Energy

Abstract

In this investigation, the collection efficiency of particulate emission control devices (PECDs), particulate matter (PM) emissions, and PM size distribution were determined experimentally at the inlet and outlet of PECDs at five coal-fired power plants. Different boilers, coals, and PECDs are used in these power plants. Measurement in situ was performed by an electrical low-pressure impactor with a sampling system, which consisted of an isokinetic sampler probe, precut cyclone, and two-stage dilution system with a sample line to the instruments. The size distribution was measured over a range from 0.03 to 10 µm. Before and after all of the PECDs, the particle number size distributions display a bimodal distribution. The PM_2.5 fraction emitted to atmosphere includes a significant amount of the mass from the coarse particle mode. The controlled and uncontrolled emission factors of total PM, inhalable PM (PM₁₀), and fine PM P(M_2.5) were obtained. Electrostatic precipitator (ESP) and baghouse total collection efficiencies are 96.38–99.89% and 99.94%, respectively. The minimum collection efficiency of the ESP and the baghouse both appear in the particle size range of 0.1–1 µm. In this size range, ESP and baghouse collection efficiencies are 85.79–98.6% and 99.54%. Real-time measurement shows that the mass and number concentration of PM₁₀ will be greatly affected by the operating conditions of the PECDs. The number of emitted particles increases with increasing boiler load level because of higher combustion temperature. During test run periods, the data reproducibility is satisfactory.