Estimating Full IM240 Emissions from Partial Test Results: Evidence from Arizona

ABSTRACT

The expense and inconvenience of enhanced-vehicle-emissions testing using the full 240-second dynamometer test has led states to search for ways to shorten the test process. In fact, all states that currently use the IM240 allow some type of fast-pass, usually as early in the test as second 31, and Arizona has allowed vehicles to fast-fail after second 93. While these shorter tests save states millions of dollars in inspection lanes and driver costs, there is a loss of information since test results are no longer comparable across vehicles. This paper presents a methodology for estimating full 240-second results from partial-test results for three pollutants: HC, CO, and NO_x. If states can convert all tests to consistent IM240 readings, they will be able to better characterize fleet emissions and to evaluate the impact of inspection and maintenance and other programs on emissions over time. Using a random sample of vehicles in Arizona which received full 240-second tests, we use regression analysis to estimate the relationship between emissions at second 240 and emissions at earlier seconds in the test. We examine the influence of other variables such as age, model-year group, and the pollution level itself on this relationship. We also use the estimated coefficients in several applications. First, we try to shed light on the frequent assertion that the results of the dynamometer test provide guidance for vehicle repair of failing vehicles. Using a probit analysis, we find that the probability that a failing vehicle will pass the test on the first retest is greater the longer the test has progressed. Second, we test the accuracy of our estimates for forecasting fleet emissions from partial-test emissions results in Arizona. We find forecasted fleet average emissions to be very close to the actual fleet averages for light-duty vehicles, but not quite as good for trucks, particularly when NO_x emissions are forecast.     

Method for reporting in-use vehicle fuel consumption and carbon dioxide emissions from a fast-pass transient inspection

A method has been developed that allows reporting of the fuel consumption and carbon dioxide (CO2) emissions for in-use vehicles from a fast-pass transient (IM240) inspection. The major technical obstacle to reporting CO2 emission rate and fuel consumption is that inspection and maintenance tests do not all use a standardized test duration or test method. The method is able to project full-duration fuel consumption from IM240 tests that actually fast-passed as early as just 30 sec from starting the test. It is based on basic considerations of the work done in driving the inspection cycle, with additional empirical adjustments. The initial application examined the differences between passing and failing inspections, and this did confirm that there are significant differences.     

Evaluation of a low-cost transient mass measurement system in vehicle inspection and maintenance testing: results of a Gordon-Darby Study

A study was performed at a Gordon-Darby centralized inspection and maintenance (I/M) test lane in Phoenix, AZ, in December 1999 for the purpose of evaluating the accuracy of production Vehicle Mass Analysis System (VMAS) equipment relative to standard IM240 equipment. Simultaneous transient mass measurements were made on random vehicles using VMAS and IM240 systems on two test lanes during regular I/M testing. Cumulative mass emissions for 846 valid tests were correlated using least-squares regression analysis. Correlation indices were > 0.99 for both carbon monoxide (CO) and nitric oxide (NO) and 0.93 for hydrocarbon (HC), and the standard errors of regression were 1.38 g/mi, 0.123 g/mi, and 0.245 g/mi for CO, NO, and HC, respectively. These strong correlation results are reflected by high excess emission identification rates of 99.4% for CO, 99.3% for NO, and 94.5% for HC when applying final IM240 cut points with a < 2% error of commission for all pollutants.     

Comment on “Mortality and Air Pollution: Revisited”

Abstract

Test-to-test variability has been observed by many current testing methods, including the Federal Test Procedure, the IM240 dynamometer test, the idle test common to many Inspection and Maintenance programs, and on-road remote sensing. The variability is attributable to the vehicle, not to the testing procedure. Because the vehicles are the dominant source of variability, the only way such vehicles can be reliably identified is through the use of multiple tests. The emissions variability increases with increasing average emissions, and it appears to be prevalent among the few newer technology vehicles with defective, but untampered, closed-loop emissions control systems (1981 and newer models). In one fleet the variable emitters constitute 2.2% to 4.8% of the vehicles and contribute 8.5% to 22% of the total carbon monoxide emissions. Scheduled I/M programs that fail to ensure repair of these vehicles allow a significant portion of vehicles with excess emissions to escape reduction measures.     

Evaluation of a Low-Cost Transient Mass Measurement System in Vehicle Inspection and Maintenance Testing: Results of a Gordon-Darby Study

Abstract

A study was performed at a Gordon-Darby centralized inspection and maintenance (I/M) test lane in Phoenix, AZ, in December 1999 for the purpose of evaluating the accuracy of production Vehicle Mass Analysis System (VMAS) equipment relative to standard IM240 equipment. Simultaneous transient mass measurements were made on random vehicles using VMAS and IM240 systems on two test lanes during regular I/M testing. Cumulative mass emissions for 846 valid tests were correlated using least-squares regression analysis. Correlation indices were >0.99 for both carbon monoxide (CO) and nitric oxide (NO) and 0.93 for hydrocarbon (HC), and the standard errors of regression were 1.38 g/mi, 0.123 g/mi, and 0.245 g/mi for CO, NO, and HC, respectively. These strong correlation results are reflected by high excess emission identification rates of 99.4% for CO, 99.3% for NO, and 94.5% for HC when applying final IM240 cut points with a <2% error of commission for all pollutants.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

High-mileage study of on-board diagnostic emissions

The 1990 Clean Air Act amendments require the U.S. Environmental Protection Agency (EPA) to set guidelines for states to follow in designing and running vehicle inspection and maintenance (I/M) programs. Included in this charge was a requirement to implement an on-board diagnostic (OBD) test for both basic and enhanced I/M programs. This paper provides the results to date of an ongoing EPA study undertaken to assess the durability of the OBD system as vehicles age and as mileage is accrued. The primary results of this effort indicate the points described below. First, the majority of high-mileage vehicles tested had emission levels within their certification limits, and their malfunction indicator light (MIL) was not illuminated, indicating that the systems are capable of working throughout the life of a vehicle. Second, OBD provides better air quality benefits than an IM240 test (using the federal test procedure [FTP] as the benchmark comparison). This statement is based on greater emissions reductions from OBD-directed repairs than reductions associated with IM240-identified repairs. In general, the benefits of repairing the OBD fails were smaller, but the aggregate benefits were greater, indicating that OBD tests find both the high-emitting and a number of marginally high-emitting vehicles without false failures that can occur with any tailpipe test. Third, vehicles that truly had high-tailpipe emissions as confirmed by laboratory IM240 and FTP testing also had illuminated MILs at a statistically significant level. Last, field data from state programs have demonstrated MIL illumination rates comparable with those seen in this work, suggesting that the vehicles sampled in this study were representative of the larger fleet. Nonetheless, it is important to continue the testing of high-mileage OBD vehicles into the foreseeable future to ensure that the systems are operating correctly as the fleet ages and as changes in emission certification levels take effect.     

High-Mileage Study of On-Board Diagnostic Emissions

Abstract

The 1990 Clean Air Act amendments require the U.S. Environmental Protection Agency (EPA) to set guidelines for states to follow in designing and running vehicle inspection and maintenance (I/M) programs. Included in this charge was a requirement to implement an on‐board diagnostic (OBD) test for both basic and enhanced I/M programs. This paper provides the results to date of an ongoing EPA study undertaken to assess the durability of the OBD system as vehicles age and as mileage is accrued. The primary results of this effort indicate the points described below. First, the majority of high‐mileage vehicles tested had emission levels within their certification limits, and their malfunction indicator light (MIL) was not illuminated, indicating that the systems are capable of working throughout the life of a vehicle. Second, OBD provides better air quality benefits than an IM240 test (using the federal test procedure [FTP] as the benchmark comparison). This statement is based on greater emissions reductions from OBD‐directed repairs than reductions associated with IM240‐identified repairs. In general, the benefits of repairing the OBD fails were smaller, but the aggregate benefits were greater, indicating that OBD tests find both the high‐emitting and a number of marginally high‐emitting vehicles without false failures that can occur with any tailpipe test. Third, vehicles that truly had high‐tailpipe emissions as confirmed by laboratory IM240 and FTP testing also had illuminated MILs at a statistically significant level. Last, field data from state programs have demonstrated MIL illumination rates comparable with those seen in this work, suggesting that the vehicles sampled in this study were representative of the larger fleet. Nonetheless, it is important to continue the testing of high‐mileage OBD vehicles into the foreseeable future to ensure that the systems are operating correctly as the fleet ages and as changes in emission certification levels take effect.     

Temperature effects on particulate emissions from DPF-equipped diesel trucks operating on conventional and biodiesel fuels

Emissions tests were conducted on two medium heavy-duty diesel trucks equipped with a particulate filter (DPF), with one vehicle using a NOx absorber and the other a selective catalytic reduction (SCR) system for control of nitrogen oxides (NOx). Both vehicles were tested with two different fuels (ultra-low-sulfur diesel [ULSD] and biodiesel [B20]) and ambient temperatures (70ºF and 20ºF), while the truck with the NOx absorber was also operated at two loads (a heavy weight and a light weight). The test procedure included three driving cycles, a cold start with low transients (CSLT), the federal heavy-duty urban dynamometer driving schedule (UDDS), and a warm start with low transients (WSLT). Particulate matter (PM) emissions were measured second-by-second using an Aethalometer for black carbon (BC) concentrations and an engine exhaust particle sizer (EEPS) for particle count measurements between 5.6 and 560 nm. The DPF/NOx absorber vehicle experienced increased BC and particle number concentrations during cold starts under cold ambient conditions, with concentrations two to three times higher than under warm starts at higher ambient temperatures. The average particle count for the UDDS showed an opposite trend, with an approximately 27% decrease when ambient temperatures decreased from 70ºF to 20ºF. This vehicle experienced decreased emissions when going from ULSD to B20. The DPF/SCR vehicle tested had much lower emissions, with many of the BC and particle number measurements below detectable limits. However, both vehicles did experience elevated emissions caused by DPF regeneration. All regeneration events occurred during the UDDS cycle. Slight increases in emissions were measured during the WSLT cycles after the regeneration. However, the day after a regeneration occurred, both vehicles showed significant increases in particle number and BC for the CSLT drive cycle, with increases from 93 to 1380% for PM number emissions compared with tests following a day with no regeneration.

Implications:?The use of diesel particulate filters (DPFs) on trucks is becoming more common throughout the world. Understanding how DPFs affect air pollution emissions under varying operating conditions will be critical in implementing effective air quality standards. This study evaluated particulate matter (PM) and black carbon (BC) emissions with two DPF-equipped heavy-duty diesel trucks operating on conventional fuel and a biodiesel fuel blend at varying ambient temperatures, loads, and drive cycles.     

The effects of repairs on tailpipe emissions for on-board diagnostics II-equipped vehicles with the malfunction indicator light illuminated

A total of 77 On-Board Diagnostics II (OBDII)-equipped vehicles with illuminated malfunction indicator lights (MILs) and non-evaporative codes were tested before and after repair. The test cycles included the Federal Test Procedure (FTP), IM240, and steady-state cycles. A total of 17 vehicles were found with emissions greater than 1.5 times their respective FTP emissions standards. Repair of these vehicles resulted in dramatic reductions in overall emissions for all the cycles. A majority of the remaining vehicles were found to have emissions below the certification standard for the FTP both before and after repair. Repairs for the vehicles with emissions <1.5 times the standard resulted in some smaller but quantifiable emission reductions over the FTP and IM240 but larger reductions over the steady-state driving tests. Misfires, bad oxygen sensors, and exhaust gas recirculation (EGR) problems were the most common non-evaporative causes for triggering the MIL. The results show some fundamental differences between identifying malfunctioning vehicles using OBDII as opposed to more traditional dynamometer tests. In particular, for many systems, OBDII identifies components that are operating outside their design specification rather than for a specific emissions threshold.     

A chassis test procedure to mimic the heavy-duty engine transient emissions certification test

In-use emissions from vehicles using heavy-duty diesel engines can be significantly higher than the levels obtained during engine certification. These higher levels may be caused by a combination of degradation of engine components, poor engine maintenance, degradation or failure of emissions after-treatment devices, and engine and emissions system tampering. A direct comparison of in-use vehicle emissions with engine certification levels, however, is not possible without removing an engine from the vehicle in order to perform engine dynamometer emissions testing. The goal of this research was to develop a chassis test procedure that mimics the engine performance, and as such the expected emissions levels, from the engine certification emissions test prescribed in the U.S. Code of Federal Regulations. Emissions measurements were taken from two engines during testing on an engine dynamometer using the transient heavy-duty Federal Test Procedure (FTP). Additionally, each engine was installed in an appropriate vehicle, and emissions measurements were taken using a chassis dynamometer while employing a vehicle driving schedule intended to match closely the instantaneous torque and speed schedule of the engine FTP. Engine and chassis testing was performed with the engines in stock (unmodified) condition as well as in several modes to simulate either tampered or poorly maintained conditions. The use of a chassis test as a predictive tool for determining whether an engine in a vehicle would pass the engine certification test has proven to be worthwhile. Analysis of the data shows that identification of chassis-mounted engines with NOx emissions above certification levels is possible by employing engine-specific correction factors. In the case of PM emissions, significant data scatter allowed only the identification of gross PM emitters. Engine tampering and poor maintenance can raise PM and NOx emissions, and these increases can be correctly identified by a chassis test. Analysis of chassis and engine CO and HC emissions did not reveal a strong enough correlation to warrant the use of the chassis test for emissions screening of these two pollutants.     

The Effects of Repairs on Tailpipe Emissions for On-Board Diagnostics II-Equipped Vehicles with the Malfunction Indicator Light Illuminated

Abstract

A total of 77 On-Board Diagnostics II (OBDII)-equipped vehicles with illuminated malfunction indicator lights (MILs) and non-evaporative codes were tested before and after repair. The test cycles included the Federal Test Procedure (FTP), IM240, and steady-state cycles. A total of 17 vehicles were found with emissions greater than 1.5 times their respective FTP emissions standards. Repair of these vehicles resulted in dramatic reductions in overall emissions for all the cycles. A majority of the remaining vehicles were found to have emissions below the certification standard for the FTP both before and after repair. Repairs for the vehicles with emissions <1.5 times the standard resulted in some smaller but quantifiable emission reductions over the FTP and IM240 but larger reductions over the steady-state driving tests. Misfires, bad oxygen sensors, and exhaust gas recirculation (EGR) problems were the most common non-evaporative causes for triggering the MIL. The results show some fundamental differences between identifying malfunctioning vehicles using OBDII as opposed to more traditional dynamometer tests. In particular, for many systems, OBDII identifies components that are operating outside their design specification rather than for a specific emissions threshold.     

A Chassis Test Procedure to Mimic the Heavy-Duty Engine Transient Emissions Certification Test

ABSTRACT

In-use emissions from vehicles using heavy-duty diesel engines can be significantly higher than the levels obtained during engine certification. These higher levels may be caused by a combination of degradation of engine components, poor engine maintenance, degradation or failure of emissions after-treatment devices, and engine and emissions system tampering. A direct comparison of in-use vehicle emissions with engine certification levels, however, is not possible without removing an engine from the vehicle in order to perform engine dynamometer emissions testing. The goal of this research was to develop a chassis test procedure that mimics the engine performance, and as such the expected emissions levels, from the engine certification emissions test prescribed in the U.S. Code of Federal Regulations. Emissions measurements were taken from two engines during testing on an engine dynamometer using the transient heavy-duty Federal Test Procedure (FTP). Additionally, each engine was installed in an appropriate vehicle, and emissions measurements were taken using a chassis dynamometer while employing a vehicle driving schedule     

负载对实际道路重型柴油车排放的影响研究

利用车载测试系统对重型柴油货车空载、50％负载和100％负载不同负载情况下在实际道路的排放进行测试,基于测试数据分析负载对重型柴油货车排放CO、HC、NOx和微小颗粒物(PM)等4种污染物的影响.不同速度区间和行驶模式下负载对排放的影响分析表明,在有负载时,大多数工况下4种污染物排放呈现增加趋势,但各速度区间和行驶模式下的增幅不尽相同,部分工况出现下降.空载时测试柴油车基于新欧洲行驶循环测试(NEDC)工况的标准化CO、HC、NOx和PM排放因子分别为3.38、0.39、6.27、0.39 g/km.对于柴油车重点污染物NOx和PM而言,与空载相比,50％负载时分别增加43％和59％,100％负载时分别增加62％和44％.     

Emission Factors for High-Emitting Vehicles Based on On-Road Measurements of Individual Vehicle Exhaust with a Mobile Measurement Platform

ABSTRACT

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO_x), and particle mass with aerodynamic diameter below 2.5 μm (PM_2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO_x, black carbon (BC), PM_2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO_x and CO fleet-average emission factors and more than 60% of PM_2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM_2.5, and NO_x tended to cluster among the same vehicles.

IMPLICATIONS This study presents the characterization of on-road vehicle emissions in Wilmington, CA, by sampling individual vehicle plumes. Approximately 5% of the vehicles were high emitters, whose emissions were more than 5 times the fleet-average values. These high emitters were responsible for 30% and more than 50% of the average emission factors of LDGVs and HDDVs, respectively. It is likely that as the overall fleet becomes cleaner due to more stringent regulations, a small fraction of the fleet may contribute a growing and disproportionate share of the overall emissions. Therefore, long-term changes in on-road emissions need to be monitored.     

Size and composition distributions of particulate matter emissions: part 1--light-duty gasoline vehicles

Size-resolved particulate matter (PM) emitted from light-duty gasoline vehicles (LDGVs) was characterized using filter-based samplers, cascade impactors, and scanning mobility particle size measurements in the summer 2002. Thirty LDGVs, with different engine and emissions control technologies (model years 1965-2003; odometer readings 1264-207,104 mi), were tested on a chassis dynamometer using the federal test procedure (FTP), the unified cycle (UC), and the correction cycle (CC). LDGV PM emissions were strongly correlated with vehicle age and emissions control technology. The oldest models had average ultrafine PM0.1 (0.056- to 0.1-microm aerodynamic diameter) and fine PM1.8 (< or =1.8-microm aerodynamic diameter) emission rates of 9.6 mg/km and 213 mg/km, respectively. The newest vehicles had PM0.1 and PM1.8 emissions of 51 microg/km and 371 microg/km, respectively. Light duty trucks and sport utility vehicles had PM0.1 and PM1.8 emissions nearly double the corresponding emission rates from passenger cars. Higher PM emissions were associated with cold starts and hard accelerations. The FTP driving cycle produced the lowest emissions, followed by the UC and the CC. PM mass distributions peaked between 0.1- and 0.18-microm particle diameter for all vehicles except those emitting visible smoke, which peaked between 0.18 and 0.32 microm. The majority of the PM was composed of carbonaceous material, with only trace amounts of water-soluble ions. Elemental carbon (EC) and organic matter (OM) had similar size distributions, but the EC/OM ratio in LDGV exhaust particles was a strong function of the adopted emissions control technology and of vehicle maintenance. Exhaust from LDGV classes with lower PM emissions generally had higher EC/OM ratios. LDGVs adopting newer technologies were characterized by the highest EC/OM ratios, whereas OM dominated PM emissions from older vehicles. Driving cycles with cold starts and hard accelerations produced higher EC/OM ratios in ultrafine particles.     

Contribution of vehicle emissions from an attached garage to residential indoor air pollution levels

The infiltration of vehicle emissions into a house from the attached garage was studied for 16 homes of differing designs using the same extensively characterized vehicle at each home. Before the in-home measurement program, the cold-start and hot-start tailpipe emissions and hot-soak evaporative emissions from a 1993 Buick Regal were measured using standard vehicle emissions measurement methods. The emissions were chemically characterized for methane, nonmethane hydrocarbons (NMHC), and carbonyl compounds. The in-home measurements occurred over two winter seasons (1997-1998 and 1998-1999) in Ottawa, Ontario, Canada. Samples of indoor air and garage atmosphere were characterized for carbon monoxide, carbon dioxide, methane, NMHC, and carbonyl compounds. During the second year, real-time measurements of carbon, carbon dioxide, and total hydrocarbons were made to determine when and for how long the emissions plume infiltrates the house. Chemical mass balance modeling results using 31 NMHC species suggest that between 9 and 71% of the concentrations measured in the house during the hot-soak test and between 13 and 85% of the concentrations measured in the house during the cold-start test could be attributed to vehicle emissions infiltrating from the garage. In contrast, increases in carbonyl compound concentrations caused by the vehicle were difficult to detect above the already significant levels found in the houses.     

Emission factors for high-emitting vehicles based on on-road measurements of individual vehicle exhaust with a mobile measurement platform

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO(x)), and particle mass with aerodynamic diameter below 2.5 microm (PM2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO(x), black carbon (BC), PM2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO(x) and CO fleet-average emission factors and more than 60% of PM2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM2.5, and NO(x) tended to cluster among the same vehicles.     

Size and Composition Distributions of Particulate Matter Emissions: Part 1—Light-Duty Gasoline Vehicles

Abstract

Size-resolved particulate matter (PM) emitted from light-duty gasoline vehicles (LDGVs) was characterized using filter-based samplers, cascade impactors, and scanning mobility particle size measurements in the summer 2002. Thirty LDGVs, with different engine and emissions control technologies (model years 1965–2003; odometer readings 1264–207,104 mi), were tested on a chassis dynamometer using the federal test procedure (FTP), the unified cycle (UC), and the correction cycle (CC). LDGV PM emissions were strongly correlated with vehicle age and emissions control technology. The oldest models had average ultrafine PM_0.1 (0.056- to 0.1-μm aerodynamic diameter) and fine PM_1.8 (≤1.8-μm aerodynamic diame ter) emission rates of 9.6 mg/km and 213 mg/km, respectively. The newest vehicles had PM_0.1 and PM_1.8 emis sions of 51 μg/km and 371 μg/km, respectively. Light duty trucks and sport utility vehicles had PM_0.1 and PM_1.8 emissions nearly double the corresponding emission rates from passenger cars. Higher PM emissions were associated with cold starts and hard accelerations. The FTP driving cycle produced the lowest emissions, followed by the UC and the CC. PM mass distributions peaked between 0.1-and 0.18-μm particle diameter for all vehicles except those emitting visible smoke, which peaked between 0.18 and 0.32 μm. The majority of the PM was composed of carbonaceous material, with only trace amounts of water-soluble ions. Elemental carbon (EC) and organic matter (OM) had similar size distributions, but the EC/OM ratio in LDGV exhaust particles was a strong function of the adopted emissions control technology and of vehicle maintenance. Exhaust from LDGV classes with lower PM emissions generally had higher EC/OM ratios. LDGVs adopting newer technologies were characterized by the highest EC/OM ratios, whereas OM dominated PM emissions from older vehicles. Driving cycles with cold starts and hard accelerations produced higher EC/OM ratios in ultrafine particles.     

A study of emissions from a Euro 4 light duty diesel vehicle with the European particulate measurement programme

The California Air Resources Board, CARB, has participated in a program to quantify particulate matter (PM) emissions with a European methodology, which is known as the Particulate Measurement Programme (PMP). The essence of the PMP methodology is that the diesel PM from a Euro 4 vehicle equipped with a Diesel Particulate Filter (DPF) consists primarily of solid particles with a size range greater than 23 nm. The PMP testing and the enhanced testing performed by CARB have enabled an increased understanding of both the progress that has been made in PM reduction, and the future remaining challenges for new and improved DPF-equipped diesel vehicles. A comparison of measured regulated emissions and solid particle number emissions with the results obtained by the PMP participating international laboratories was a success, and CARB’s measurements and standard deviations compared well with the other laboratories. Enhanced measurements of the influence of vehicle conditioning prior to testing on PM mass and solid particle number results were performed, and some significant influences were discovered. For example, the influence of vehicle preconditioning on particle number results was significant for both the European and USA test driving cycles. However, the trends for the cycles were opposite with one cycle showing an increase and the other cycle showing a decrease in particle number emissions. If solid particle size distribution and total particle numbers are to be used as proposed in PMP, then a greater understanding of the quality and errors associated with measurement technologies is advisable.In general, particle counting instruments gave results with similar trends, but cycle-to-cycle testing variation was observed. Continuous measurements of particle number concentrations during test cycles have given detailed insight into PM generation. At the present time there is significant variation in the capabilities of the particle counting instruments in terms of particle size and concentration.Current measurements show the existence of a large number of volatile and semi-volatile particles of yet-to-be-resolved chemical composition in diesel exhaust, especially during DPF regeneration, and these particles are not included in the PMP methodology because they are smaller than 20 nm. It will be very challenging to improve our understanding of this class of diesel particulate matter.