Heterogeneous Fenton-like discoloration of Rhodamine B using natural schorl as catalyst: optimization by response surface methodology

A cationic dye, Rhodamine B (RhB), could be efficiently discolored by heterogeneous Fenton-like reaction catalyzed by natural schorl. In this work, with the main goal of the optimization for RhB discoloration, central composite design under the response surface methodology (RSM) was employed for the experiment design and process optimization. The significance of a second-order polynomial model for predicting the optimal values of RhB discoloration was evaluated by the analysis of variance and 3D response surface and counter plots for the interactions between two variables were constructed. The Pareto graphic analysis of the discoloration process indicated that, among all the variables, solution pH (X ₃, 47.95 %) and H₂O₂ concentration (X ₁, 24.39 %) had the largest influences on the heterogeneous Fenton-like discoloration of RhB. Based on the model prediction, the optimum conditions for RhB discoloration were determined to be 45 mM H₂O₂ concentration, 2.5 g/L schorl dosage, solution pH 2, and 110 min reaction time, with the maximum RhB discoloration ratio of 98.86 %. The corresponding experimental value of RhB discoloration ratio under the optimum conditions was determined as 99.31 %, which is very close to the optimized one, implying that RSM is a powerful and satisfactory strategy for the process optimization.     

Electrosorption and photocatalytic one-stage combined process using a new type of nanosized TiO2/activated charcoal plate electrode

In the present study, an activated charcoal (AC) plate was prepared by physical activation method. Its surface was coated with TiO₂ nanoparticles by electrophoretic deposition (EPD) method. The average crystallite size of TiO₂ nanoparticles was determined approximately 28 nm. The nature of prepared electrode was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller (BET) surface area measurement before and after immobilization. The electrosorption and photocatalytic one-stage combined process was investigated in degradation of Lanasol Red 5B (LR5B), and the effect of dye concentration, electrolyte concentration, pH, voltage, and contact time was optimized and modeled using response surface methodology (RSM) approach. The dye concentration of 30 mg L^?1, Na₂SO₄ concentration of 4.38 g L^?1, pH of 4, voltage of 250 mV, and contact time of 120 min were determined as optimum conditions. Decolorization efficiency increased in combined process to 85.65 % at optimum conditions compared to 66.03 % in TiO₂/AC photocatalytic, 20.09 % in TiO₂/AC electrosorption, and 1.91 % in AC photocatalytic processes.     

Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

The objective of this study was to examine the effects of adsorbability and number of sulfonate group on solar photocatalytic degradation of mono azo methyl orange (MO) and diazo Reactive Green 19 (RG19) in single and binary dye solutions. The adsorption capacity of MO and RG19 onto the TiO₂ was 16.9 and 26.8 mg/g, respectively, in single dye solution, and reduced to 5.0 and 23.1 mg/g, respectively, in the binary dye solution. The data obtained for photocatalytic degradation of MO and RG19 in single and binary dye solution were well fitted with the Langmuir–Hinshelwood kinetic model. The pseudo-first-order rate constants of diazo RG19 were significant higher than the mono azo MO either in single or binary dye solutions. The higher number of sulfonate group in RG19 contributed to better adsorption capacity onto the surface of TiO₂ than MO indicating greater photocatalytic degradation rate.     

Adsorptive removal and photocatalytic decomposition of sulfamethazine in secondary effluent using TiO2–zeolite composites

We investigated the adsorption and decomposition of sulfamethazine (SMT), which is used as a synthetic antibacterial agent and discharged into environmental water, using high-silica Y-type zeolite (HSZ-385), titanium dioxide (TiO₂), and TiO₂–zeolite composites. By using ultrapure water and secondary effluent as solvents, we prepared SMT solutions (10 μg/L and 10 mg/L) and used them for adsorption and photocatalytic decomposition experiments. When HSZ-385 was used as an adsorbent, rapid adsorption of SMT in the secondary effluent was confirmed, and the adsorption reached equilibrium within 10 min. The photocatalytic decomposition rate using TiO₂ in the secondary effluent was lower than that in ultrapure water, and we clarified the inhibitory effect of ions and organic matter contained in the secondary effluent on the reaction. We synthesized TiO₂–zeolite composites and applied them to the removal of SMT. During the treatment of 10 μg/L SMT in the secondary effluent using the composites, 76 % and more than 99 % of the SMT were decomposed within 2 and 4 h by photocatalysis. The SMT was selectively adsorbed onto high-silica Y-type zeolite in the composites. Resultantly, the inhibitory effect of the coexisting materials was reduced, and the composites could remove SMT more effectively compared with TiO₂ alone in the secondary effluent.     

In situ photoelectrochemical/photocatalytic study of a dye discoloration in a microreactor system using TiO2 thin films

Introduction

In this work, we report in situ studies of UV photoelectrocatalytic discoloration of a dye (indigo carmine) by a TiO₂ thin film in a microreactor to demonstrate the driving force of the applied electrode potential and the dye flow rate toward dye discoloration kinetics.

Methods

TiO₂ 65-nm-thick thin films were deposited by PVD magnetron sputtering technique on a conducting glass substrate of fluorinated tin oxide. A microreactor to measure the discoloration rate, the electrode potential, and the photocurrent in situ, was developed. The dye solutions, before and after measurements in the microreactor, were analyzed by Raman spectroscopy.

Results

The annealed TiO₂ thin films had anatase structure with preferential orientation (101). The discoloration rate of the dye increased with the applied potential to TiO₂ electrode. Further, acceleration of the photocatalytic reaction was achieved by utilizing dye flow recirculation to the microreactor. In both cases the photoelectrochemical/photocatalytic discoloration kinetics of the dye follows the Langmuir?CHinshelwood model, with first-order kinetics.

Conclusions

The feasibility of dye discoloration on TiO₂ thin film electrodes, prepared by magnetron sputtering using a flow microreactor system, has been clearly demonstrated. The discoloration rate is enhanced by applying a positive potential (E _AP) and/or increasing the flow rate. The fastest discoloration and shortest irradiation time (50?min) produced 80% discoloration with an external anodic potential of 0.931?V and a flow rate of 12.2?mL?min^?1.     

A mini-review on rare earth metal-doped TiO<Subscript>2</Subscript> for photocatalytic remediation of wastewater

Titanium dioxide (TiO₂) has been considered a useful material for the treatment of wastewater due to its non-toxic character, chemical stability and excellent electrical and optical properties which contribute in its wide range of applications, particularly in environmental remediation technology. However, the wide band gap of TiO₂ photocatalyst (anatase phase, 3.20 eV) limits its photocatalytic activity to the ultraviolet region of light. Besides that, the electron-hole pair recombination has been found to reduce the efficiency of the photocatalyst. To overcome these problems, tailoring of TiO₂ surface with rare earth metals to improve its surface, optical and photocatalytic properties has been investigated by many researchers. The surface modifications with rare earth metals proved to enhance the efficiency of TiO₂ photocatalyts by way of reducing the band gap by shifting the working wavelength to the visible region and inhibiting the anatase-to-rutile phase transformations. This review paper summarises the attempts on modification of TiO₂ using rare earth metals describing their effect on the photocatalytic activities of the modified TiO₂ photocatalyst.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

Photocatalytic reduction of carbon dioxide over Cu/TiO<Subscript>2</Subscript> photocatalysts

The photocatalytic reduction of CO₂ with H₂O was investigated using Cu/TiO₂ photocatalysts in aqueous solution. For this purpose, Cu/TiO₂ photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N₂ physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO₂ decreased in the presence of Cu/TiO₂ in comparison to pure TiO₂, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H₂ production necessary for CO₂ reduction more difficult.     

Photocatalytic degradation of Reactive Red 195 using anatase/brookite TiO2 mesoporous nanoparticles: Optimization using response surface methodology (RSM) and kinetics studies

In the present study, the photocatalytic degradation of Reactive Red 195 (RR195) from aqueous samples under UV-A irradiation by using anatase/brookite TiO₂ (A/B TiO₂) mesoporous nanoparticles has been investigated. Batch experiments were conducted to study the effects of the main parameters affecting the photocatalytic process. The effects and interactions of most influenced parameters, such as substrate concentration and catalyst load, were evaluated and optimized by using a central composite design model and a response surface methodology. The results indicated that the dye degradation efficiency in the experimental domain investigated was mainly affected by the tested variables, as well as their interaction effects. Analysis of variance showed a high coefficient of determination value (R ²?=?0.9947), thus ensuring a satisfactory adjustment of the first-order regression model (2FI model) with the experimental data. The obtained results also indicate that catalyst loading plays an important role in determining the removal efficiency of RR195 attributable to both photodegradation and adsorption process. Under optimal conditions (initial dye concentration (50 mg/L) and catalyst loading (2,000 mg/L), A/B TiO₂ showed similar removal efficiency compared to that of commercial titania (Degussa P25). Also, at these conditions, complete degradation of RR195 can be achieved by both catalysts within 15 min under UV-A irradiation. The experiments demonstrated that dye removal on the prepared A/B TiO₂ was facilitated by the synergistic effects between adsorption and photocatalysis. Photocatalytic mineralization of RR195 was monitored by total organic carbon. The recycling experiments confirmed the stability of the catalyst.     

Synthesis of BiVO4/TiO2 composites and evaluation of their photocatalytic activity under indoor illumination

BiVO₄/TiO₂ composites with different weight ratios have been prepared by coprecipitation-based reactions followed by either thermal or hydrothermal treatment with the aim of evaluating the TiO₂ photosensitization by BiVO₄. The obtained materials present in all cases the desired monoclinic phase of BiVO₄ and anatase phase of TiO₂. Visible light absorption increased with increasing amount of bismuth vanadate. XPS results reveal the surface enrichment of Ti with respect to the bulk composition in samples characterised by a higher content of BiVO₄. The photocatalytic activity of the prepared materials was tested for the degradation of isopropanol in the gas phase under indoor illumination conditions. Although none of the composites was able to improve the activity of TiO₂, the low BiVO₄ containing samples appear as more suitable for further synthesis tuning.     

Photocatalytic degradation of contaminants of concern with composite NF-TiO2 films under visible and solar light

This study reports the synthesis and characterization of composite nitrogen and fluorine co-doped titanium dioxide (NF-TiO₂) for the removal of contaminants of concern in wastewater under visible and solar light. Monodisperse anatase TiO₂ nanoparticles of different sizes and Evonik P25 were assembled to immobilized NF-TiO₂ by direct incorporation into the sol–gel or by the layer-by-layer technique. The composite films were characterized with X-ray diffraction, high-resolution transmission electron microscopy, environmental scanning electron microscopy, and porosimetry analysis. The photocatalytic degradation of atrazine, carbamazepine, and caffeine was evaluated in a synthetic water solution and in an effluent from a hybrid biological concentrator reactor (BCR). Minor aggregation and improved distribution of monodisperse titania particles was obtained with NF-TiO₂-monodisperse (10 and 50 nm) from the layer-by-layer technique than with NF-TiO₂?+?monodisperse TiO₂ (300 nm) directly incorporated into the sol. The photocatalysts synthesized with the layer-by-layer method achieved significantly higher degradation rates in contrast with NF-TiO₂-monodisperse titania (300 nm) and slightly faster values when compared with NF-TiO₂-P25. Using NF-TiO₂ layer-by-layer with monodisperse TiO₂ (50 nm) under solar light irradiation, the respective degradation rates in synthetic water and BCR effluent were 14.6 and 9.5?×?10^?3?min^?1 for caffeine, 12.5 and 9.0?×?10^?3?min^?1 for carbamazepine, and 10.9 and 5.8?×?10^?3?min^?1 for atrazine. These results suggest that the layer-by-layer technique is a promising method for the synthesis of composite TiO₂-based films compared to the direct addition of nanoparticles into the sol.     

Study of TiO2 anatase nano and microstructures with dominant {001} facets for NO oxidation

Introduction

TiO₂ anatase nanoplates and hollow microspheres were fabricated by a solvothermal?Chydrothermal method using titanium isopropoxide as a titanium precursor and hydrofluoric acid as a capping agent in order to enhance the formation of the {001} crystal facets of the anatase nanocrystals.

Methods

These different morphological structures of TiO₂ anatase can be achieved by only changing the solvent, keeping the amount of the precursor and of the capping agent identical during the solvothermal?Chydrothermal process.

Results and discussion

After calcination of the samples, the adsorbed fluoride atoms on the {001} crystal facets of the TiO₂ anatase nanocrystals were completely removed from their surface according to XPS analysis. The calcined TiO₂ anatase structures were higher crystallized and the specific surface area of the catalysts increased, enhancing their photocatalytic activity in comparison to the non-calcined TiO₂ anatase structures. All TiO₂ anatase samples with adsorbed as well as non-adsorbed fluoride atoms on their {001} crystal facets, exhibited a higher photonic efficiency than Degussa P25, which was used as a reference.

Conclusion

The fluoride free TiO₂ anatase nanoplates exhibited the best photocatalytic activity in oxidizing the NO gas to NO₂ and NO₃ ^?.     

Coupling of titania with multiwall carbon nanotubes for decomposition of gas-phase pollutants under simulated indoor conditions

This study synthesized multiwall carbon nanotube (MWNT)–titania (TiO₂) composites and examined their characteristics and photocatalytic performance for the cleaning of gas-phase benzene, toluene, ethyl benzene, and o-xylene (BTEX) under simulated indoor conditions. Optical and spectral surveys of the as-synthesized composite confirmed that the TiO₂ nanoparticles were bound intimately to the MWNT networks. The photocatalytic performance was evaluated using an annular-type reactor inner-coated with MWNT–TiO₂ or Degussa P25 TiO₂. The composite revealed gas removal ability superior to that of stand-alone TiO₂. This composite was also less affected by humidity during toluene decomposition compared to the previous result obtained from a stand-alone TiO₂. Unlike another previous result obtained from the TiO₂, the performance of the composite was not affected by changes in input concentration (IC) within a simulated indoor air quality range (0.1–1.0 ppm) but it decreased significantly when the IC was increased to 5 and 10 ppm. As the flow rate was decreased from 4.0 to 1.0 L min^?1, the average efficiency for the target compounds increased to 95% or ～100%. The MWNT–TiO₂ composite could be applied effectively to the decomposition for BTEX under certain simulated indoor conditions.

Implications: Unlike water applications, there are few reports of gas-phase applications of multiwall carbon nanotubes (MWCNT)–TiO₂ composites. This study found that MWCNT–TiO₂ composites showed performance in the removal of toxic gaseous aromatic superior to that of stand-alone TiO₂. In addition, the pollutant degradation efficiency of the composite was less affected by humidity than for a stand-alone TiO₂ unit within a simulated indoor relative humidity range. Moreover, unlike the TiO₂ unit, the composite's performance was not affected by variations in the input concentrations within the simulated indoor air quality (IAQ) range. In addition, the decomposition efficiencies increased to 100% with decreasing flow rate.     

Use of carbon-based composites to enhance performance of TiO<Subscript>2</Subscript> for the simultaneous removal of nitrates and organics from aqueous environments

The simultaneous photocatalytic removal of nitrate from aqueous environment in presence of organic hole scavenger using TiO₂ has long been explored. However, the use of unmodified TiO₂ in such reaction resulted in non-performance or release of significant amount of undesirable reaction products in the process, a problem that triggered surface modification of TiO₂ for enhanced photocatalytic performance. Previous studies focused on decreasing rate of charge carrier recombination and absorption of light in the visible region. Yet, increasing active sites and adsorption capacity by combining TiO₂ with a high surface area adsorbent such as activated carbon (AC) remains unexploited. This study reports the potential of such modification in simultaneous removal of nitrates and oxalic acid in aqueous environment. The adsorptive behaviour of nitrate and oxalic acid on TiO₂ and TiO₂/AC composites were studied. The Langmuir adsorption coefficient for nitrate was four times greater than that of oxalic acid. However, the amount of oxalic acid adsorbed was about 10 times greater than the amount of nitrate taken up. Despite this advantage, the materials did not appear to produce more active photocatalysts for the simultaneous degradation of nitrate and oxalic acid. The photocatalytic activity of TiO₂ and its carbon-based composites was improved by combination with Cu₂O particles. Consequently, 2.5 Cu₂O/TiO₂ exhibited the maximum photocatalytic performance with 57.6 and 99.8% removal of nitrate and oxalic acid, respectively, while selectivity stood at 45.7, 12.4 and 41.9% for NH₄⁺, NO₂^? and N₂, respectively. For the carbon based, 2.5 Cu₂O/TiO₂-20AC showed removal of 12.7% nitrate and 80.3% oxalic acid and achieved 21.6, 0 and 78.4% selectivity for NH₄⁺, NO₂^? and N₂, respectively. Using the optimal AC loading (20 wt%) resulted in significant decrease in the selectivity for NH₄⁺ with no formation of NO₂^?, which unveils that selectivity for N₂ and low/no selectivity for undesirable products can be manipulated by controlling the rate of consumption of oxalic acid. In contract, no nitrate reduction was observed with Cu₂O promoted TiO₂-T and its TiO₂-(T)-20AC, which may be connected to amorphous nature of TiO₂-T and perhaps served as charge carrier trapping sites that impeded activity.     

Effect of Nb doping on structural, optical and photocatalytic properties of flame-made TiO2 nanopowder

TiO₂:Nb nanopowders within a dopant concentration in the range of 0.1?C15?at.% were prepared by one-step flame spray synthesis. Effect of niobium doping on structural, optical and photocatalytic properties of titanium dioxide nanopowders was studied. Morphology and structure were investigated by means of Brunauer?CEmmett?CTeller isotherm, X-ray diffraction and transmission electron microscopy. Diffuse reflectance and the resulting band gap energy were determined by diffuse reflectance spectroscopy. Photocatalytic activity of the investigated nanopowders was revised for the photodecomposition of methylene blue (MB), methyl orange (MO) and 4-chlorophenol under UVA and VIS light irradiation. Commercial TiO₂-P25 nanopowder was used as a reference. The specific surface area of the powders was ranging from 42.9?m²/g for TiO₂:0.1?at.% Nb to 90.0?m²/g for TiO₂:15?at.% Nb. TiO₂:Nb particles were nanosized, spherically shaped and polycrystalline. Anatase was the predominant phase in all samples. The anatase-related transition was at 3.31?eV and rutile-related one at 3.14?eV. TiO₂:Nb nanopowders exhibited additional absorption in the visible range. In comparison to TiO₂-P25, improved photocatalytic activity of TiO₂:Nb was observed for the degradation of MB and MO under both UVA and VIS irradiation, where low doping level (Nb?<?1?at.%) was the most effective. Niobium doping affected structural, optical and photocatalytic properties of TiO₂. Low dopant level enhanced photocatalytic performance under UVA and VIS irradiation. Therefore, TiO₂:Nb (Nb?<?1?at.%) can be proposed as an efficient selective solar light photocatalyst.     

Antifungal efficiency assessment of the TiO2 coating on façade paints

The work studies the photocatalytic activity and the antifungal efficiency of the TiO₂/Zn-Al coatings placed on the target commercial façade paints. The photocatalytic active nanocomposite based on TiO₂ and Zn-Al-layered double hydroxides (ZnAl-LDHs) was synthesized by a wet impregnation technique with 3 % w/w TiO₂. The freshly prepared suspension was applied by spray technique on the surfaces of the white façade paints. The goal of the work was to develop a method that quickly quantifies the antifungal activity of the commercial façade paints with and without biocidal components covered with a photocatalytic coating. The essence of the proposed method is the monitoring of the fungal growth (artificial ageing conditions) and the quantification of its development (UV-A 0.13 mWcm^?2) on the façade paint surfaces. A special fungus nutrient (potato dextrose agar (PDA)) was inoculated with the spores of the Aspergillus niger ATCC 6275, and the test samples (façade paints with and without photocatalytic coating) were placed on the inoculated nutrient in the petri dishes. The images of the fungal growth on the samples of the facade paints, during a period of 5 days, were imported into Matlab R2012a where they were converted to binary images (BW), based on the adequate threshold. The percentage of the surface coverage was calculated by applying the specifically written program code which determines the ratio of the black and white pixels. The black pixels correspond to the surface covered with hyphae and mycelia of the fungus.     

The photocatalytic degradation of methylene blue by green semiconductor films that is induced by irradiation by a light-emitting diode and visible light

This study develops a low-energy rotating photocatalytic contactor (LE-RPC) that has Cu-doped TiO₂ films coated on stainless-steel rotating disks, to experimentally evaluate the efficiency of the degradation and decolorization of methylene blue (MB) under irradiation from different light sources (visible 430 nm, light-emitting diode [LED] 460 nm, and LED 525 nm). The production of hydroxyl radicals is also examined. The experimental results show that the photocatalytic activity of TiO₂ that is doped with Cu²⁺ is induced by illumination with visible light and an LED. More than 90% of methylene blue at a 10 mg/L concentration is degraded after illumination by visible light (430 nm) for 4 hr at 20 rpm. This study also demonstrates that the quantity of hydroxyl radicals produced is directly proportional to the light energy intensity. The greater the light energy intensity, the greater is the number of hydroxyl radicals produced.

Implications: The CuO-doped anatase TiO₂ powder was successfully synthesized in this study by a sol–gel method. The catalytic abilities of the stainless-steel film were enhanced in the visible light regions. This study has successfully modified the nano-photocatalytic materials to drop band gap and has also successfully fixed the nano-photocatalytic materials on a substratum to effectively treat dye wastewater in the range of visible light. The results can be useful to the development of a low-energy rotating photocatalytic contactor for decontamination purposes.     

Highly active photocatalytic coatings prepared by a low-temperature method

Photocatalytic properties of titanium (IV) oxide (TiO₂) in anatase form can be used for various purposes, including photocatalytic purification of water. For such an application, suspended or fixed photocatalytic reactors are used. Those with fixed phase seem to be preferred due to some advantages, one of which is the avoidance of photocatalyst filtration. To avoid leaching and exfoliation of the fixed phase, an immobilization procedure leading to a good adhesion of a catalyst to a substrate is crucial. Within this work, we present physical and photocatalytic characterization results of five commercially available TiO₂ photocatalysts (P25, P90, PC500, KRONOClean 7000, VPC-10) and one pigment (Hombitan LO-CR-S-M), which were successfully immobilized on glass slides by a “sol suspension” procedure. Different mechanical tests and characterization methods were used to evaluate the stability and morphology of the layers. Evaluation of photocatalytic activity was done by tests under UVA and UV–vis irradiation, using a method based on the detection of the fluorescent oxidation product of terephthalic acid (TPA), i.e., hydroxyterephthalic acid (HTPA). Aeroxide® P90 incorporated into the silica-titania binder was the most photocatalytically active layer and, unlike the others, showed significant increase of photocatalytic activity through the entire range of tested UVA irradiation intensities (2.3 mW/cm²–6.1 mW/cm²). The high mechanical stability of some photocatalytic layers allows using them in water photocatalytic purification reactions.     

Shape-dependent bactericidal activity of TiO2 for the killing of Gram-negative bacteria Agrobacterium tumefaciens under UV torch irradiation

This paper demonstrated the relative bactericidal activity of photoirradiated (6W-UV Torch, λ?>?340 nm and intensity?=?0.64 mW/cm²) P25–TiO₂ nanoparticles, nanorods, and nanotubes for the killing of Gram-negative bacterium Agrobacterium tumefaciens LBA4404 for the first time. TiO₂ nanorod (anatase) with length of 70–100 nm and diameter of 10–12 nm, and TiO₂ nanotube with length of 90–110 nm and diameter of 9–11 nm were prepared from P-25 Degussa TiO₂ (size, 30–50 nm) by hydrothermal method and compared their biocidal activity both in aqueous slurry and thin films. The mode of bacterial cell decomposition was analyzed through transmission electron microscopy (TEM), Fourier transform-infrared (FT-IR), and K⁺ ion leakage. The antimicrobial activity of photoirradiated TiO₂ of different shapes was found to be in the order P25–TiO₂?>?nanorod?>?nanotube which is reverse to their specific surface area as 54?<?79?<?176 m² g^?1, evidencing that the highest activity of P25–TiO₂ nanoparticles is not due to surface area as their crystal structure and surface morphology are entirely different. TiO₂ thin films always exhibited less photoactivity as compared to its aqueous suspension under similar conditions of cell viability test. The changes in the bacterial surface morphology by UV-irradiated P25–TiO₂ nanoparticles was examined by TEM, oxidative degradation of cell components such as proteins, carbohydrates, phospholipids, nucleic acids by FT-IR spectral analysis, and K⁺ ion leakage (2.5 ppm as compared to 0.4 ppm for control culture) as a measure of loss in cell membrane permeability.