Synthesis and environmental degradation of polyesters based on poly (ε-caprolactone)

Poly (-caprolactone) (PCL), poly (-valerolactone) (PVL), poly (-caprolactone-co--valerolactone) [P(CL-co-VL)], and poly (-caprolactone-co-ethylene oxide-co--caprolactone) (PCL-PEO-PCL) were synthesized by ring-opening and diol-initiated polymerization of -caprolactone and -valerolactone. The degradation of the samples by chemical hydrolysis and in a soil burial test was evaluated. It was found that PCL, PVL, and P(CL-co-VL) degrade mainly enzymatically. The rate of degradation depends on their molecular weight, chemical structure, composition, and morphology. PCL-PEO-PCL block copolymers exhibit a repelling effect to the microorganisms in the soil, which depends on the molecular weight and relative amount of PEO block in the copolymer.     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Correlating the Spatial Distribution of Atmospheric Ammonia with δ15N Values at an Ammonia Release Site

A field ammonia (NH₃) release experiment and open top chambers containing moorland monoliths continuously fumigated with NH₃ or sprayed with NH₄Cl were used to assess the potential for using ¹⁵N values in determining the area of influence around a point NH₃ emission source. ¹⁵N values are being increasingly used as environmental tracers and we tested the hypothesis that the ¹⁵N signal from an NH₃ emission source is observable in nearby vegetation. Using modified monitoring devices, atmospheric NH₃ concentrations were found to decrease with distance from source, with ¹⁵N values also reflecting this trend, producing a signal shift with changing concentration. Open top chamber studies of ¹⁵N values of Calluna vulgaris (L.) Hull indicated a correlation with deposition treatments in current year shoots. Analysis of Calluna shoots from the NH₃ release showed a similar trend of ¹⁵N enrichment. Significant linear correlations between ¹⁵N and percent N in plant material were found, both in the controlled conditions of the open top chambers and at the NH₃ release site, illustrating the possible use of this technique in N deposition biomonitoring.     

Remediation of Persistent Organic Pollutants Using a Novel Two-Phase Soil Washing Biosorption Process

A two-phase soil washing biosorption process was developed for the remediation of p,p-DDT-contaminated soil. The process involved desorption of contaminants from soil using dilute primary alcohols (40% 1-propanol) followed by contaminant removal from cosolvent solutions using fungal biosorption. Bench scale remediation studies were preformed to simulate ex situ (recycling experiment) or in situ (soil column study) treatment strategies. Both systems were effective at cleaning the soil to below Australian regulatory p,p-DDT levels. After 50–80 hours of soil washing, over 93% of p,p-DDT was removed from the soil(990 mg kg^-1 to <65 mg kg^-1) using either of these methods.p,p-DDT was removed from the cosolvent phase by sorption onto the fungal biomass. This resulted in only low levels of p,p-DDT remaining in the cosolvent solution(<1.5 mg l^-1). The application of both treatment strategies resulted in the rapid clean up of p,p-DDT-contaminated soil and the potential to recycle cosolvent solutions. The ability to recycle cosolvent solutions provides a mechanism for cost reductions of the remediation strategy.     

Tree Leaf Biomarkers for Atmospheric Nitrogen Deposition

The aim of this paper was to investigate the effects of nitrogen (N) deposition on tree N cycling and identify potential biomarkers forNdeposition. Between April and October 2002 extensive fieldwork was undertaken at Mardley Heath in Hertfordshire. This woodland, located adjacent to the A1(M) motorway, is exposed to high levels of atmospheric nitrogen oxides from the traffic. Measurements of ¹⁵N, in vivo nitrate reductase (NR) activity, tissue, xylem and surface nitrate concentrations as well as N concentration and growth were made along a 700-m transect at 90° to the motorway. The ¹⁵N data show that oxidised N from the road traffic is taken up by nearby trees and is incorporated into plant tissues. Our measurements of NR activities suggest elevated rates close to the motorway. However, xylem sap, leaf tissue and leaf surface nitrate concentrations showed no differences between the roadside location and the most distant sampling point from the motorway. Taken together the ¹⁵N and nitrate reductase data suggest uptake and assimilation of N through the foliage.We conclude that for this lowland deciduouswoodland, tissue, xylem and surface measurements of nitrate are unreliable biomarkers for N deposition whereas ¹⁵N, growth measurements and integrated seasonal NR might be useful. The results also point to the benefit of roadside tree planting to screen pollution from motor vehicles.     

Sulfur Metabolism in Polluted Sphagnum Peat Bogs: A Combined 34S–35S–210Pb Study

The size and isotopic behavior of sulfur pools in²¹⁰Pb-dated peat cores were investigated to obtain aninsight into retention mechanisms of pollutant S in twomountain-top peatlands of the Northern Czech Republic, CentralEurope. The bogs were situated 40 km apart in an area whichbetween the years 1985 and 1995 received as much as 130 kg Sha^-1 yr^-1 from the atmosphere. Vertical peataccretion was faster at Pod Jelení horou (JH) than atVelký moál (VM). Organic carbon-bonded S was themost abundant sulfur pool, constituting 77 and 65 wt. % at JHand VM, respectively. At JH both the S concentration maximumand the highest annual S deposition rate were displaceddownward by more than 20 years (from 1987 to the 1960s)indicating that the buried S is vertically mobile. At VM the Sconcentration was the highest in the topmost 2-cm section eventhough atmospheric S deposition peaked in 1987. Differentmechanisms of S isotope redistribution prevailed in thetopmost peat layers at JH, where a negative ³⁴Sshift occurred, and at VM, where a positive ³⁴Sshift occurred. Bacterial sulfate reduction was responsiblefor the negative ³⁴S shift at JH. One possibleexplanation of the positive ³⁴S shift at VM isrelease of ³²S-enriched products of mineralization duringpeat diagenesis. There was a strong positive correlationbetween the abundance of total and pyrite S along the profiles.The presence of pyrite S at VM (526 ± 60 ppm) suggestedthat even at VM bacterial sulfate reduction occurred. Ananaerobic incubation of JH peat indicated sulfate reductionrate of 600 nmol g^-1 day^-1. The turnover times forinorganic S pools were shorter than for the organic S pools.Cumulative S contents in the Czech peat bogs were found to besignificantly lower than in similar sites in the NortheasternU.S., even though the atmospheric S inputs were more thanthree times higher at the Czech sites. Possible causes of suchdiscrepancy are discussed.     

The Role Played by Acetyl Group Distribution Patterns in Substituted Starch Toward Enzymatic De-acetylation and Chain Fragmentation

The nature and distribution of the acetylated groups were evaluated by ¹³C-NMR and ¹H-NMR. The starch substrate with a DS of 1.5 comprises only two patterns: -(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose. The starch with a DS of 3.0 also comprises two patterns: 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose; whereas starch (DS = 1.9) contains 4 patterns: 2,3,6-tri-O-acetyl--(14)-d-glucopyranose, 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose terminal, 2,6-di-O-acetyl--(14)-d-glucopyranose, and 3,6-di-O-acetyl--(14)-d-glucopyranose. Using esterase from Viscozyme, it has been possible to hydrolyze up to 7% of the DS 3.0 starch. An -amylase (Fungamyl 800) was then added to these acetylesterases. With a 2.4 FAU/mL fraction of -amylase and 2.4 U/mL from the Viscozyme's acetylesterase, 28% of the acetylated end groups were hydrolyzed for the starch substrates with DS 3.0. Moreover, a synergic action between -amylase and acetylesterase was noticed, allowing fragmentation of 32% for DS 1.5, 30% for DS 1.9, and 11% for DS 3.0.     

The Application of Stable Isotopes for Assessing the Hydrological, Sulfur, and Iron Balances of Acidic Mining Lake ML 111 (Lusatia, Germany) as a Basis for Biotechnological Remediation

Stable isotope (¹⁸O–H₂O, ²H–H₂O ³⁴S–SO₄ ^2-) andhydrochemical data (SO₄ ^2-, Fe-concentrations) have beenused to estimate the annual groundwater inflow and outflow of mining lake ML 111 and to calculate the total amount of dissolvedsulfate and iron that is carried into the lake by groundwater. The hydrological balance suggests an annual groundwater inflow of 23 700 m³ and an annual groundwater outflow of 15 700 m³. The calculation of the sulfur and iron balances yielded an annual sulfate input of 37 800 kg and an annual iron input of 7000 kg with the groundwater inflow. Furthermore it was shown that significant fluxes of these elements go into the lake sediments which results in continuous release of acidity in the lake water.     

Investigation of the Aerobic Biodegradability of Several Types of Cyclodextrins in a Laboratory-Controlled Composting Test

The biodegradation of several types of cyclodextrins (CDs) under laboratory-controlled composting conditions was investigated. CDs are used in a broad range of applications in food, pharmaceutical, medical, chemical, and textile industries because of their specific chemical characteristics related to their hydrophobic interior and hydrophilic exterior. The three naturally occurring cyclodextrins -CD, -CD, and -CD proved to be completely and readily biodegradable. Chemical modification of these basic compounds can have a major impact on the biodegradation rate and final biodegradation percentage. Fully acetylated -CD and -CD were found to be nonbiodegradable during 45 days of composting. Reducing the degree of acetylation had a positive effect on the biodegradation. Complete biodegradation was obtained for partially acetylated -CD with a degree of substitution (DS) of 7. The methylation (DS = 13) of -CD resulted in an undegradable compound during the 47 days composting, while (2-hydroxy)propyl--CD reached a plateau in biodegradation at a percentage of 20%. The incorporation of the antimicrobial agents imazalil and allyl-isothiocyanate into -CD had no negative impact on biodegradation, which makes these antimicrobial agents/CD complexes suitable for incorporation into biodegradable active packaging.     

A New Approach for the Flocculation Mechanism of Chitosan

A peak III/I ratio (_peak) in pyrene-fluorescence spectrum was used to measure the polarity of microenvironment of chitosan adsorbing pyrene molecules. The authors detected the pyrene-fluorescence spectrum of chitosan with different degrees of deacetylation (DD) and determined the relationship between the flocculation of bentonite colloid and the _peak of chitosan with a different molecular weight (MW) and DD. It can be concluded that MW rather than DD plays a key role in the flocculation and that bond bridging rather than charge neutralization dominates the flocculation with chitosan from a microenvironmental structure of view.     

Catalytic decomposition of hydrocarbon into hydrogen and carbon in a spouted-bed reactor as the second-stage reactor of a plastic recycling process

A two-stage process for the chemical recycling of plastics is proposed. In this process, which consists of two reactors, plastics are converted into hydrogen and carbon. In the first reactor, plastic chips are thermally decomposed into hydrocarbons. In the second reactor, the hydrocarbons formed in the first reactor are catalytically decomposed into carbon and hydrogen. In this study, in order to obtain basic data for the second reactor, propene was catalytically decomposed in a laboratory-scale spouted-bed reactor (600mm high, 21.6mm internal diameter, made of SUS304). The effect of the type of spouting medium used on the decomposition behavior of propene was investigated using four types of spouting medium (nickel-plated -alumina, palladium-plated -alumina, nickel-impregnated -alumina, and -alumina). The nickel-impregnated -alumina gave the best propene conversion and hydrogen yield.     

Novel Biobased Polyurethanes Synthesized from Soybean Phosphate Ester Polyols: Thermomechanical Properties Evaluations

Biobased polyurethanes from soybean oil–derived polyols and polymeric diphenylmethane diisocyanate (pMDI) are prepared and their thermomechanical properties are studied and evaluated. The cross-linked biobased polyurethanes being prepared from soy phosphate ester polyols with hydroxyl contents ranging from 122 to 145 mg KOH/g and pMDI within 5 min of reaction time at 150°C in absence of any catalyst show cross-linking densities ranging from 1.8 × 10³ to 3.0 × 10³ M/m³, whereas glass transition temperatures vary from approximately 69 to 82°C. The loss factor (tan ) curves show single peaks for all these biobased polyurethanes, thus indicating a single-phase system. The storage moduli (G) at 30°C range from 4 × 10⁸ to 1.3 × 10⁹ Pa. Upon postcure at 150°C, the thermomechanical properties can be optimized. Cross-link densities are improved significantly for hydroxyl content of 139 and 145 mg KOH/g at curing time of 24 h. Similarly, glass transition temperature (T_g) and storage moduli around and after T_g are increased. Meanwhile, tan intensities decrease as result of restricted chain mobility. Longer exposure time (24 h) induces thermal degradation, as evidenced by thermogravimetric analysis (TGA). The dynamic mechanical (DMA) analysis shows that postcure at 100°C for times exceeding 24 h also leads to improved properties. However, cross-linking densities are lower compared to postcure carried out at 150°C.     

Biodegradability: An assessment of commercial polymers according to the Canadian method for anaerobic conditions

The degradation of several biodegradable polymers was measured as a result of exposure to an anaerobic medium. The polymers investigated included materials based upon polylactic acid, polylactone, and poly(hydroxy butyrate/valerate) as well as those incorporating starch-based materials. The degradation was monitored by methane and carbon dioxide evolution. In addition, the physical and chemical changes were noted as a result of exposure. These measurements included changes in mass, dimension, and molecular weight. FTIR, UV-vis, proton, and¹³C NMR spectra were also recorded prior to and after exposure. The results clearly indicated that several biological and chemical degradation processes were occurring with the biodegradable polymers studied.Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois.Issued as NRCC No. 37549.     

On East Asian Sand and Duststorms and Associated Significant Dustfall Observed from January to May 2001

Monitoring of dust pollution at the western shore of Tae-ahn Peninsula (TAP) and in the Chongju area of central Korea was carried out from January to May 2001. It was found that in Koreathere were 9 cases of sand and duststorms (DS) and 16 associatedsignificant dustfall (SD) days. Observed maximum concentrations of DS and SD coming from NW China and Mongolia were in the rangeof 300–920 for TSP, 200–690 for PM₁₀ and 100–170 g m^-3 for PM_2.5.Satellite measurements clearly showed the formation and subsequent movement of DS to the Korean Peninsula and onward to the Korea East Sea, Japan and the Gulf of Alaska. According to satellite image analysis of dust clouds there were abundant coarse particles, measuring in size of 11.0 m. Medium-sizedparticles measuring in the range of 3.5–7.0 were also prevalent,while fine particles of less than 2.0 m were less distinctive in reflectivity. Measured values of PM_2.5 were alsorelatively low with SD events.The measured average pH values of dusty precipitation associatedwith DS were 7.24. Alkaline precipitation can play a `temporary'role in the neutralization of acidified soil until the subsequentevent of acidic rain. The new selection criteria of SD days from PM_2.5 at 85 g m^-3, PM₁₀ 190 g m^-3 and TSP 250 g m^-3 are recommended on dust pollution occurring from the invasion of a DS elsewhere.     

Assessment of Bacterial Degradation of Aromatic Hydrocarbons in the Environment by Analysis of Stable Carbon Isotope Fractionation

¹³C/¹²C stable carbon isotope fractionation was used to assess biodegradation in contaminated aquifers with toluene as a model compound. Different strains of anaerobic bacteria (Thauera aromatica, Geobacter metallireducens, and the sulfate-reducing strain TRM1) showed consistent ¹³C/¹²C carbon isotope fractionation with fractionation factors between C = 1.0017 and 1.0018. In contrast, three cultures of aerobic organisms, using different mono- and dioxygenase enzyme systems to initiate toluene degradation, showed variable isotope fractionation factors of C = 1.0027 (Pseudomonasputida strain mt-2), C = 1.0011 (Ralstonia picketii), andC = 1.0004 (Pseudomonas putida strain F1). The great variability of isotope fractionation between different aerobic bacterial strains suggests that interpretation of isotope data in oxic habitats can only be qualitative. A soil column was run as a model system for contaminated aquifers with toluene as the carbon source and sulfate as the electron acceptor and samples were taken at different ports along the column. Microbial toluene degradation was calculated based on the ¹³C/¹²C isotope fractionation factors of the batch culture experiments together with the observed ¹³C/¹²C isotope shifts of the residual toluene fractions. The calculated percentage of biodegradation, B, correlated well with the decreasing toluene concentrations at the sampling ports and indicated the increasing extent of biodegradation along the column. The theoretical toluene concentrations as calculated based on the isotope values matched the measured concentrations at the different sampling ports indicating that the Rayleigh equation can be used to calculate biodegradation in quasi closed systems based on measured isotope shifts. A similar attempt was performed to assess toluene degradation in a contaminated, anoxic aquifer. A transect of groundwater wells was monitored along the main direction of the groundwater flow and revealed decreasing concentrations accompanied with an increase in the ¹³C/¹²C stable carbon isotope ratio of the residual toluene. Calculation of the extent of biodegradation based on the isotope values and laboratory derived isotope fractionation factors showed that the residual toluene was degraded to more than 99% by microbial activity. Calculation of the theoretical residual toluene concentrations based on the measured isotope values described the strongly decreasing concentrations along the plume. Other aromatic hydrocarbons like benzene and naphthalene which were analysed in the same course also showed decreasing concentrations along the groundwater flow path accompanied by increasing ¹³C values indicating biodegradation.     

Synthesis and biodegradation of poly(γ-butyrolactone-co-l-lactide)

Biodegradable polyesters were synthesized by ring-opening copolymerization of -butyrolactone (BL) and its derivatives withl-lactide (LLA). Although tetraphenyl tin was the main catalyst used, other organometallic catalysts were used as well.¹H and¹³C NMR spectra showed that poly(BL-co-LLA)s were statistical and that their number-average molecular weights were as high as 7×10⁴. The maximum BL content obtained from copolymerization BL/LLA was around 17%. TheT _m andT _g values of the copolymers showed a gradual depression with an increase in BL content. NoT _m was obtained for the copolymers containing more than 13 mol% BL. The biodegradability of the copolyesters was evaluated by enzymatic hydrolysis and nonenzymatic hydrolysis tests. The enzymatic hydrolysis was carried out at 37°C for 24 h using lipases fromRhizopus arrhizus andR. delemar. Hydrolyses by both lipases showed that an increase in BL content of the copolymer resulted in enhanced biodegradability. Nonenzymatic accelerated hydrolysis of copolymers at 70°C was found to increase proportionally to their exposure time. The hydrolysis rate of these copolymers was considerably faster than that of PLLA. The higher hydrolyzability was recorded for the BL-rich copolymers. The copolymerization of -methyl--butyrolactone (MBL) or -ethyl--butyrolactone (EBL) with LLA resulted in relatively LA-rich copolymers.     

Soil Respiration in Relation to Small-Scale Patterns of Lead and Mercury in Mor Layers of Southern Swedish Forest Sites

Pollution-related lead (Pb) andmercury (Hg) in mor layers of Southern Swedenmight have effects on soil biology, although inthe literature effect concentrations have beenidentified at much higher levels. Considerablesmall-scale spatial variability in heavy metalcontents and microbial respiration in mor layersof forest sites was used to calculatecorrelations that could reveal toxic effects.Negative correlations were always strongest atsites with high loads of Pb or Hg, which was considered to indicate metal toxicity. The highload sites were found in Southwestern Sweden,locally at a motorway and at a chlorine-alkalifactory. Other factors of possible influence,such as other pollutants, age of organic materialor climatic differences, would affect high andlow load sites alike. Negative correlations withrespiration were found for Pb at sites with 74 g g^-1 of mean Pb content in O_f-layer and for Hg at 0.25 g g^-1.     

Synthesis of a block copolymer of poly(3-hydroxybutyrate) and poly(ethylene glycol) and its application to biodegradable polymer blends

A block copolymer {P[(R,S)-HB-b-EG]} of atactic poly[(R,S)-3-hydroxybutyrate] {P[(R,S)-HB]} and poly(ethylene glycol) (PEG) was prepared by the ring-opening polymerization of -butyrolactone in the presence of a macroinitiator (PEG/ZnEt₂/H₂O) which had been produced by the reaction of ,-dihydroxy PEG ( _n=3000) with ZnEt₂/H₂O (1/0.6) catalyst. The block copolymer ( _n=10,500, _w/ _n=1.2) was an A-B-A triblock copolymer comprising atactic P[(R,S)-HB] (A) and PEG (B) segments. The miscibility, physical properties, and biodegradability of binary blends of microbial poly[(R)-3-hydroxybutyrate] {P[(R)-HB]} with the block copolymer P[(R,S)-HB-b-EG] has been studied. The glass-transition temperature (T _g) data showed that the P[(R)-HB]/P[(R,S)-HB-b-EG] blend was miscible in the amorphous state. The P[(R)-HB] film became flexible and tough by means of blending with P[(R,S)-HB-b-EG] block copolymer. The enzymatic degradation of blend films was carried out at 37°C and pH 7.4 in a 0.1M phosphate solution of an extracellular PHB depolymerase fromAlcaligenes faecalis. The enzymatic degradation took place solely on the surface of the blend films.     

The contemporary copper cycle of Asia

A regional stock and flow model for an industrial metal was developed based on the substance-flow framework. Using this model, the contemporary copper cycle of the Asian region was constructed by aggregating country-level production and import and export data for different stages of the copper cycle. The reliability and availability of data were assessed both qualitatively and quantitatively. Asia as a region is a net importer of copper. There is a significant build-up of copper in use at a rate of nearly 3TgCu/year. The per capita generation of copper waste (0.4kgCu/(capita-year)) and the rate of secondary recovery of copper are low compared with Europe and North America. Japan's rates of use, waste generation, and recycling of copper are all much larger than the continental average. A tremendous potential exists in the region to utilize the copper content of the in-use reservoir, and subsequently to enhance copper recycling rates in the future. A set of metrics for the copper cycle is suggested in order to address sustainability issues related to resource policy and the environmental management of copper.     

The Effect of Nitrogen Enrichment on the Carbon Sink in Coniferous Forests: Uncertainty and Sensitivity Analyses of Three Ecosystem Models

Estimates of the global carbon sink induced by nitrogen enrichment range vary widely, from nearly zero to 2.3 Gt C year^-1. It is necessary to reduce this uncertainty if we are to make accurate predictions of the future magnitude of the terrestrial carbon sink. Here, we present a Monte Carlo approach to uncertainty and sensitivity analysis of three ecosystem models, Century,BGCand Hybrid. These models were applied to a coniferous forest ecosystem in Sweden. The best estimate of the change in total carbon content of the ecosystem with the cumulative change in nitrogen deposition over 100 years, C_total/N_deposition was 20.1 kg C (kg N)^-1 using the pooled mean, with a pooled standard deviation of 13.8 kg C (kg N)^-1. Variability in parameters accounted for 92% of the total uncertainty in C_total/N_deposition, and only 8% was attributable to differences between models. The most sensitive parameters were those which controlled the allocation of assimilate between leaves, roots and stem. In particular, an increase in allocation to fine roots led to a large reduction in C_total/N_deposition in all models, because the fine roots have a very high turnover rate, and extra carbon allocated there is soon lost through mortality and decomposition.