Modelling greenhouse gas emissions from European conventional and organic dairy farms

Agriculture is an important contributor to global emissions of greenhouse gases (GHG), in particular for methane (CH₄) and nitrous oxide (N₂O). Emissions from farms with a stock of ruminant animals are particularly high due to CH₄ emissions from enteric fermentation and manure handling, and due to the intensive nitrogen (N) cycle on such farms leading to direct and indirect N₂O emissions. The whole-farm model, FarmGHG, was designed to quantify the flows of carbon (C) and nitrogen (N) on dairy farms. The aim of the model was to allow quantification of effects of management practices and mitigation options on GHG emissions. The model provides assessments of emissions from both the production unit and the pre-chains. However, the model does not quantify changes in soil C storage.Model dairy farms were defined within five European agro-ecological zones for both organic and conventional systems. The model farms were all defined to have the same utilised agricultural area (50 ha). Cows on conventional and organic model farms were defined to achieve the same milk yield, so the basic difference between conventional and organic farms was expressed in the livestock density. The organic farms were defined to be 100% self-sufficient with respect to feed. The conventional farms, on the other hand, import concentrates as supplementary feed and their livestock density was defined to be 75% higher than the organic farm density. Regional differences between farms were expressed in the milk yield, the crop rotations, and the cow housing system and manure management method most common to each region.The model results showed that the emissions at farm level could be related to either the farm N surplus or the farm N efficiency. The farm N surplus appeared to be a good proxy for GHG emissions per unit of land area. The GHG emissions increased from 3.0 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 56 kg N ha⁻¹ year⁻¹ to 15.9 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 319 kg N ha⁻¹ year⁻¹. The farm N surplus can relatively easily be determined on practical farms from the farm records of imports and exports and the composition of the crop rotation. The GHG emissions per product unit (milk or metabolic energy) were quite closely related to the farm N efficiency, and a doubling of the N efficiency from 12.5 to 25% reduced the emissions per product unit by ca. 50%. The farm N efficiency may therefore be used as a proxy for comparing the efficiencies of farms with respect to supplying products with a low GHG emission.     

Life-cycle environmental and economic impacts of energy-crop fuel-chains: an integrated assessment of potential GHG avoidance in Ireland

This paper combines life-cycle analyses and economic analyses for Miscanthus and willow heat and electricity fuel-chains in Ireland. Displaced agricultural land-uses and conventional fuels were considered in fuel-chain permutations. Avoided greenhouse gas (GHG) emissions ranged from 7.7 to 35.2 t CO₂ eq. ha⁻¹ a⁻¹. Most fuel-chain permutations exhibited positive discounted financial returns, despite losses for particular entities at a farm-gate processed-biomass price of €100 t⁻¹ dry-matter. Attributing a value of €10 t⁻¹ CO₂ eq. to avoided GHG emissions, but subtracting financial returns associated with displaced fuel supplies, resulted in discounted annual national economic benefits (DANEBs) ranging from −457 to 1887€ ha⁻¹ a⁻¹. Extrapolating a plausible combination of fuel-chains up to a national indicative scenario resulted in GHG emission avoidance of 3.56 Mt CO₂ eq. a⁻¹ (5.2% of national emissions), a DANEB of 167 M€, and required 4.6% of national agricultural land area. As cost-effective national GHG avoidance options, Miscanthus and willow fuel-chains are robust to variation in yields and CO₂ price, and appear to represent an efficient land-use option (e.g. compared with liquid biofuel production). Policies promoting utilisation of these energy-crops could avoid unnecessary, and environmentally questionable, future purchase of carbon credits, as currently required for national Kyoto compliance.     

Methane,nitrous oxide and ammonia emissions during storage and after application of dairy cattle slurry and influence of slurry treatment

Slurries are a significant source of CH₄, NH₃ and N₂O emissions to the atmosphere. The research project aimed at quantifying CH₄, NH₃ and N₂O emissions from liquid manure stores and after manure application under field conditions. The influence of the manure treatment options “no treatment”, “slurry separation”, “anaerobic digestion”, “slurry aeration” and “straw cover” on the emission level was investigated. Approximately 10 m³ of differently treated slurry were stored in pilot scale slurry tanks. Emissions were followed for c. 80 days. After the storage period, slurries were applied to permanent grassland. Greenhouse gas emissions from slurry were mainly caused by methane emissions during storage and by nitrous oxide emissions after field application of manures. Mitigation of GHG emissions can be achieved by a reduction in slurry dry matter and easily degradable organic matter content. Ammonia emissions mainly occurred after field application. Untreated slurry emitted 226.8 g NH₃ m⁻³ and 92.4 kg CO₂ eq. m⁻³ (storage and field application). Slurry separation (liquid fraction and composting of the solid fraction) resulted in NH₃ losses of 402.9 g m⁻³ and GHG losses of 58.5 kg CO₂ eq. m⁻³. Anaerobic digestion was a very effective means to reduce GHG emissions. 37.9 kg CO₂ eq. m⁻³ were lost. NH₃ emissions were similar to those from untreated slurry. Covering the slurry store with a layer of chopped straw instead of a wooden cover increased NH₃ emissions to 320.4 g m⁻³ and GHG emissions to 119.7 kg CO₂ eq. m⁻³. Slurry aeration nearly doubled NH₃ emissions compared to untreated slurry. GHG emissions were reduced to 53.3 kg CO₂ eq. m⁻³.     

Mitigation of greenhouse gas emissions by anaerobic digestion of cattle slurry

Biogas treatment of animal manures is an upcoming technology because it is a way of producing renewable energy (biogas). However, little is known about effects of this management strategy on greenhouse gas (GHG) emissions during fermentation, storage, and field application of the substrates compared to untreated slurries. In this study, we compared cattle slurry and cattle slurry with potato starch as additive during the process of fermentation, during storage and after field application. The addition of potato starch strongly enhanced CH₄ production from 4230 l CH₄ m⁻³ to 8625 l CH₄ m⁻³ in the fermenter at a hydraulic retention time (HRT) of 29 days. Extending the HRT to 56 days had only a small effect on the CH₄ production. Methane emissions from stored slurry depended on storage temperature and were highest from unfermented slurry followed by the slurry/starch mixture. Gas emissions from untreated and fermented slurry during storage were further analyzed in a pilot-scale experiment with different levels of covering such as straw cover, a wooden lid and no cover. Emissions of greenhouse gases (CH₄, N₂O, NH₃) were in the range of 14.3–17.1 kg CO₂ eq. m⁻³ during winter (100 day storage period) and 40.5–90.5 kg CO₂ eq. m⁻³ during summer (140 day storage period). A straw cover reduced NH₃ losses, but not overall GHG emissions, whereas a solid cover reduced CH₄ and NH₃ emissions. After field application, there were no significant differences between slurry types in GHG emissions (4.15–8.12 kg CO₂ eq. m⁻³ a⁻¹). GHG emissions from slurry stores were more important than emissions after field application. Co-digestion of slurry with additives such as starch has a large potential to substitute fossil energy by biogas. On a biogas plant, slurry stores should be covered gas-tight in order to eliminate GHG emissions and collect CH₄ for electricity production.     

Long-term impact of a gliricidia-maize intercropping system on carbon sequestration in southern Malawi

Tree/crop systems under agroforestry practice are capable of sequestering carbon (C) in the standing biomass and soil. Although studies have been conducted to understand soil organic C increases in some agroforestry technologies, little is known about C sequestered in simultaneous tree/crop intercropping systems. The main objective of this study was to determine the effect of agroforestry practice on C sequestration and CO₂-C efflux in a gliricidia-maize intercropping system. The experiment was conducted at an experimental site located at the Makoka Agricultural Research Station, in Malawi. The studies involved two field plots, 7-year (MZ21) and 10-year (MZ12), two production systems (sole-maize and gliricidia-maize simultaneous intercropping systems). A 7-year-old grass fallow (Grass-F) was also included. Gliricidia prunings were incorporated at each time of tree pruning in the gliricidia-maize. The amount of organic C recycled varied from 0.8 to 4.8 Mg C ha⁻¹ in gliricidia-maize and from 0.4 to 1.0 Mg C ha⁻¹ in sole-maize. In sole-maize, net decreases of soil carbon of 6 Mg C ha⁻¹ at MZ12 and 7 Mg C ha⁻¹ at MZ21 in the topsoil (0–20 cm) relative to the initial soil C were observed. After 10 years of continuous application of tree prunings C was sequestered in the topsoil (0–20 cm) in gliricidia-maize was 1.6 times more than in sole-maize. A total of 123–149 Mg C ha⁻¹ were sequestered in the soil (0–200 cm depth), through root turnover and pruning application in the gliricidia-maize system. Carbon dioxide evolution varied from 10 to 28 kg ha⁻¹ day⁻¹ in sole-maize and 23 to 83 kg ha⁻¹ day⁻¹ in gliricidia-maize. We concluded that gliricidia-maize intercropping system could sequester more C in the soil than sole-maize.     

Monitoring GHG from manure stores on organic and conventional dairy farms

Organic farming methods are claimed to be more environmentally friendly than conventional methods and the EU MIDAIR project had an overall aim to compare emissions from organic dairy farming with conventional methods of milk production. Manure stores are the second largest source of methane emissions (after enteric fermentation) on European dairy farming.The aim of this project was to measure green house gas (GHG) emissions from manures in covered and uncovered slurry stores and farm yard manure (FYM) heaps. The chosen method for measuring these emissions was the tracer ratio method, using sulphur hexafluoride (SF₆) as the tracer gas, the limitations of this method prevented successful measurements being made on some of the stores and a modified method was used on the covered stores. The difference in concentration of the upwind and downwind samples and interfering sources were limiting factors. FYM emission measurements were successful only when the manure was stored indoors.Methane emissions were successfully measured over a 12 month period from the uncovered slurry stores. Emission rates from the uncovered slurry stores on the conventional farm and the organic farm ranged from 14.4 to 49.6 and from 12.4 to 42.3 g C m⁻³ d⁻¹, respectively, with the mean CH₄ emission rates of 35 and 26 g C m⁻³ d⁻¹. On both farms, nitrous oxide emissions were close to zero.Methane emissions measured from the indoor organic FYM in summer were 17.1 g C m⁻³ d⁻¹ and the nitrous oxide emission was 411 mg N m⁻³ d⁻¹.The covered slurry stores were in such close proximity to other GHG sources that the tracer ratio method was unsuitable and the air-injection method was adopted. The measured emissions from covered slurry stores of CH₄, CO₂ and NH₃ were, respectively, 14.9 g C m⁻³ d⁻¹, 12.9 g C m⁻³ d⁻¹ and 18.6 mg NH₃ m⁻² d⁻¹ of slurry in February and 12.0 g C m⁻³ d⁻¹, 9.5 g C m⁻³ d⁻¹ and 335 mg NH₃ m⁻² d⁻¹ slurry in March. No nitrous oxide production could be measured.     

Comparing intensive,extensified and organic grassland farming in southern Germany by process life cycle assessment

To reduce the environmental burden of agriculture, suitable methods to comprehend and assess the impact on natural resources are needed. One of the methods considered is the life cycle assessment (LCA) method, which was used to assess the environmental impacts of 18 grassland farms in three different farming intensities — intensive, extensified, and organic — in the Allgäu region in southern Germany. Extensified and organic compared with intensive farms could reduce negative effects in the abiotic impact categories of energy use, global warming potential (GWP) and ground water mainly by renouncing mineral nitrogen fertilizer. Energy consumption of intensive farms was 19.1 GJ ha⁻¹ and 2.7 GJ t⁻¹ milk, of extensified and organic farms 8.7 and 5.9 GJ ha⁻¹ along with 1.3 and 1.2 GJ t⁻¹ milk, respectively. Global warming potential was 9.4, 7.0 and 6.3 CO₂-equivalents ha⁻¹ and 1.3, 1.0 and 1.3 CO₂-equivalents t⁻¹ milk for the intensive, extensified and organic farms, respectively. Acidification calculated in SO₂-equivalents was high, but the extensified (119 kg SO₂ ha⁻¹) and the organic farms (107 kg SO₂ ha⁻¹) emit a lower amount compared with the intensive farms (136 kg SO₂ ha⁻¹). Eutrophication potential computed in PO₄-equivalents was higher for intensive (54.2 kg PO₄ ha⁻¹) compared with extensified (31.2 kg PO₄ ha⁻¹) and organic farms (13.5 kg PO₄ ha⁻¹). Farmgate balances for N (80.1, 31.4 and 31.1 kg ha⁻¹) and P (5.3, 4.5 and −2.3 kg ha⁻¹) for intensive, extensified and organic farms, respectively, indicate the different impacts on ground and surface water quality. Analysing the impact categories biodiversity, landscape image and animal husbandry, organic farms had clear advantages in the indicators number of grassland species, grazing cattle, layout of farmstead and herd management, but indices in these categories showed a wide range and are partly independent of the farming system.     

Effect of straw addition on nitrous oxide and methane emissions from stored farmyard manures

Stored solid manure heaps can be a significant source of nitrous oxide (N₂O) and methane (CH₄) emissions. The manure characteristics influence emissions and solid manure heaps can be managed to promote aerobic decomposition during storage. Increasing the carbon (C) content of the manure heap with high-C additives, such as straw, may provide the opportunity for N₂O and CH₄ emission reduction. Greenhouse gas (GHG) emissions from conventionally produced farmyard manure (FYM) have been quantified, but there is little data on emissions from organically produced FYM. N₂O and CH₄ emissions were measured using a small-scale storage method from FYM collected from organic and conventional dairy units under a range of storage conditions with and without extra straw addition.The organic and the conventional FYM were similar in composition except for the higher C and dry matter content in the organic FYM and in the FYM with added straw. This resulted in mean total emissions of N₂O and CH₄ being lower from the organic (27 g N t⁻¹) than the conventional FYM (52 g N t⁻¹) and from the treatments with straw added (32 g N t⁻¹) than those without (47 g N t⁻¹). The initial C:N ratio and dry matter content of the stored FYM were the most important factors affecting N₂O and CH₄ emissions although the FYM temperature also affected CH₄ emissions. Adding high-C additives, such as straw could be a promising strategy for reducing GHG emissions because it influences the dry matter content, C:N ratio and aeration of the manure. The small-scale FYM storage method were shown to be a reliable and an easy method to quantify emissions under a range of environmental conditions and manure manipulations and so develop effective manure management practices to reduce GHG emissions.     

Balancing of greenhouse gas emissions and economic efficiency for biogas-production through anaerobic co-fermentation of slurry with organic waste

Using the organic fraction of municipal solid waste (OFMSW) for biogas production might contribute to greenhouse gas mitigation, but emissions linked with biogas production can reduce these beneficial effects. Therefore the emissions of NH₃, CH₄ and N₂O and costs caused by treating OFMSW by co-fermentation with slurry were calculated in detail from literature data, and strategies for reducing emissions were evaluated. Emission factors were calculated for single gases during storage and after application. The sensitivity of the calculations concerning the organic dry matter content of OFMSW, retention time and CH₄-yield was analyzed. The anaerobic co-fermentation of OFMSW increased biogas yields and contributed to the reduction of CO₂ emissions with 32 to 152 kg CO₂ t⁻¹ organic waste depending on application and storage techniques used for the fermentation residues. Considering a payment of 0.1 €/kWh for the electricity produced, the costs for utilization of OFMSW in slurry based biogas plants were calculated to range between 34 and 38 € t⁻¹. Measures for mitigating greenhouse gas emissions by covering the fermentation residue stores proved to be more cost effective with 3–31 € t⁻¹ CO₂ compared to immediate harrowing or injecting the residues during field application.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

Dairy farm CH4 and N2O emissions,from one square metre to the full farm scale

The greenhouse gas emissions from agricultural systems contribute significantly to the national budgets for most countries in Europe. Measurement techniques that can identify and quantify emissions are essential in order to improve the selection process of emission reduction options and to enable quantification of the effect of such options. Fast box emission measurements and mobile plume measurements were used to evaluate greenhouse gas emissions from farm sites. The box measurement technique was used to evaluate emissions from farmyard manure and several other potential source areas within the farm. Significant (up to 250 g CH₄ m⁻² day⁻¹and 0.4 g N₂O m⁻² day⁻¹) emissions from ditches close to stables on the farm site were found.Plume emission measurements from individual manure storages were performed at three sites. For a manure storage with 1200 m³ dairy slurry in Wageningen emission factors of 11 ± 5 g CH₄ m⁻³ manure day⁻¹ and 14 ± 8 mg N₂O m⁻³ manure day⁻¹ were obtained in February 2002.Mobile plume measurements were carried out during 4 days at distances between 30 and 300 m downwind of 20 different farms. Total farm emissions levels ranged from 14 to 95 kg CH₄ day⁻¹ for these sites. Expressed as emission per animal the levels were 0.7 ± 0.4 kg CH₄ animal⁻¹ day⁻¹ for conventional farms. For three farms that used straw bedding for the animals1.4 ± 0.2 kg CH₄ animal⁻¹ day⁻¹ was obtained. These factors include both respired methane and emission from manure in the stable and the outside storages.For a subset of these farms the CH₄ emission was compared with monthly averaged model emission calculations using FarmGHG. This model calculates imports, exports and flows of all products through the internal chains on the farm using daily time steps. The fit of modelled versus measured data has a slope of 0.97 but r² = 0.27. Measurements and model emission estimates agree well on average, for large farms within 30%. For small farms the differences can be up to a factor of 3. CH₄ emissions during winter seem to be underestimated.     

Environmental consequences of different beef production systems in the EU

The aim of this paper is to examine the environmental consequences of beef meat production in the EU, using a life cycle approach. Four beef production systems were studied – three from intensively reared dairy calves and one from suckler herds. According to the results of the analysis, the contributions from the production of 1 kg beef meat (slaughter weight) to global warming, acidification, eutrophication, land use and non-renewable energy use were lower for beef from dairy calves than from suckler herds (16.0–19.9 versus 27.3 kg CO₂e, 101–173 versus 210 g SO₂e, 622–1140 versus 1651 g NO₃e, 16.5–22.7 versus 42.9 m²year, and 41.3–48.2 versus 59.2 MJ, respectively). The breakdown analysis helped identify the key areas in the “cradle to farm gate” beef production system where sustainable management strategies are needed to improve environmental performance. The study also included a sensitivity analysis to preliminarily estimate GHG emissions from beef production systems if land opportunity cost and land use change related to grazing and feed crop production for beef were taken into account. If so, the contribution from the production of 1 kg beef to global warming would increase by a factor of 3.1–3.9, based on a depreciation period of 20 years. This highlights the importance of taking into account the impacts of land use in assessing the environmental impacts of livestock production.     

Nitrous oxide emissions from organic and conventional crop rotations in five European countries

Nitrous oxide (N₂O) emissions from agriculture are currently estimated from N inputs using emission factors, and little is known about the importance of regional or management-related differences. This paper summarizes the results of a study in which N₂O emission rates were recorded on 15–26 occasions during a 12-month period in organic and conventional dairy crop rotations in five European countries (Austria, Denmark, Finland, Italy, UK). A common methodology based on static chambers was used for N₂O flux measurements, and N₂O data were compiled together with information about N inputs (from fertilizers, N₂ fixation, atmospheric deposition and excretal returns), crop rotations and soil properties. Organic rotations received only manure as N fertilizer, while manure accounted for 0–100% of fertilizer N in conventional rotations. A linear regression model was used to examine effects of location, system and crop category on N₂O emissions, while a second model examined effects of soil properties. Nitrous oxide emissions were higher from conventional than from organic crop rotations except in Austria and, according to the statistical analysis, the differences between locations and crop categories were significant. Ammonium was significantly related to N₂O emissions, although this effect was dominated by observations from a grazing system. Despite the limited number of samplings, annual emissions were estimated by interpolation. Across the two systems and five locations there was a significant relationship between total N inputs and N₂O emissions at the crop rotation level which indicated that annually 1.6 ± 0.2% (mean ± standard error) of total N inputs were lost as N₂O, while there was a background emission of 1.4 ± 0.3 kg N₂O-N ha⁻¹ year⁻¹. Although this measurement program emphasized system effects at the expense of high temporal resolution, the results indicate that N input is a significant determinant for N₂O emissions from agricultural soils.     

Carbon footprint of sugar produced from sugarcane in eastern Thailand

Carbon footprint (CFP) of sugar produced from sugarcane in eastern Thailand was estimated from greenhouse gas emissions (CO₂, CH₄, and N₂O) during the sugarcane cultivation and milling process. The use of fossil fuels, chemical and organic fertilizer and sugarcane biomass data during cultivation were collected from field surveys, questionnaires and interviews. Sugar mill emissions, fossil fuel utilization and greenhouse gas emission from wastewater treatments were included. The results show that sugar production has a carbon footprint of 0.55 kg CO₂e kg^?1 sugar. This carbon footprint was a sum of 0.49 kg CO₂e kg^?1 sugar from sugarcane cultivation and 0.06 kg CO₂e kg^?1 sugar from the milling process. For the cultivation part, most of the GHGs emissions were from fertilizer, fossil fuel use and biomass burning. The CFP in eastern Thailand is sensitive to the type of data selected for calculation and of variations of farm inputs during sugarcane cultivation. There was no significant difference of CFP among farm sizes, although small farms tended to give a relatively higher CFP than that of medium and large farms.     

Evaluation of two soil carbon models using two Kenyan long term experimental datasets

RothC and Century are two of the most widely used soil organic matter (SOM) models. However there are few examples of specific parameterisation of these models for environmental conditions in East Africa. The aim of this study was therefore, to evaluate the ability of RothC and the Century to estimate changes in soil organic carbon (SOC) resulting from varying land use/management practices for the climate and soil conditions found in Kenya. The study used climate, soils and crop data from a long term experiment (1976–2001) carried out at The Kabete site at The Kenya National Agricultural Research Laboratories (NARL, located in a semi-humid region) and data from a 13 year experiment carried out in Machang’a (Embu District, located in a semi-arid region). The NARL experiment included various fertiliser (0, 60 and 120 kg of N and P₂O₅ ha⁻¹), farmyard manure (FYM—5 and 10 t ha⁻¹) and plant residue treatments, in a variety of combinations. The Machang’a experiment involved a fertiliser (51 kg N ha⁻¹) and a FYM (0, 5 and 10 t ha⁻¹) treatment with both monocropping and intercropping. At Kabete both models showed a fair to good fit to measured data, although Century simulations for treatments with high levels of FYM were better than those without. At the Machang’a site with monocrops, both models showed a fair to good fit to measured data for all treatments. However, the fit of both models (especially RothC) to measured data for intercropping treatments at Machang’a was much poorer. Further model development for intercrop systems is recommended. Both models can be useful tools in soil C predictions, provided time series of measured soil C and crop production data are available for validating model performance against local or regional agricultural crops.     

Greenhouse gas emissions from production and use of used cooking oil methyl ester as transport fuel in Thailand

Biodiesel, produced from various vegetable and/or animal oils, is one of the most promising alternative fuels for transportation in Thailand. Currently, the waste oils after use in cooking are not disposed adequately. Such oils could serve as a feedstock for biodiesel which would also address the waste disposal issue. This study compares the life cycle greenhouse gas (GHG) emissions from used cooking oil methyl ester (UCOME) and conventional diesel used in transport. The functional unit (FU) is 100 km transportation by light duty diesel vehicle (LDDV) under identical driving conditions. Life cycle GHG emissions from conventional diesel are about 32.57 kg CO₂-eq/FU whereas those from UCOME are 2.35 kg CO₂-eq/FU. The GHG emissions from the life cycle of UCOME are 93% less than those of conventional diesel production and use. Hence, a fuel switch from conventional diesel to UCOME will contribute greatly to a reduction in global warming potential. This will also support the Thai Government's policy to promote the use of indigenous and renewable sources for transportation fuels.     

Exceedance of modern ‘background’ fine-grained sediment delivery to rivers due to current agricultural land use and uptake of water pollution mitigation options across England and Wales

Excessive loss of fine-grained sediment to rivers is widely recognised as a global environmental problem. To address this issue, policy teams and catchment managers require an estimate of the ‘gap’ requiring remediation, as represented by the excess above ‘background’ losses. Accordingly, recent work has estimated the exceedance of modern ‘background’ sediment delivery to rivers at national scale across England and Wales due to (i) current agricultural land cover, cropping and stocking, and (ii) current land use corrected for the uptake of on-farm mitigation measures. This sectoral focus recognises that, nationally, agriculture has been identified as the principal source of fine sediment loss to the aquatic environment. Two estimates of modern ‘background’ sediment loss, based on paleolimnological evidence, were used in the analysis; the target modern ‘background’ (TMBSDR) and maximum modern ‘background’ (MMBSDR) sediment delivery to rivers. For individual (n = 4485) non-coastal water bodies, the sediment ‘gap’ in excess of TMBSDR and MMBSDR, due to current land cover, cropping and stocking, was estimated to range up to 1368 kg ha⁻¹ yr⁻¹ (median 61 kg ha⁻¹ yr⁻¹) and 1321 kg ha⁻¹ yr⁻¹ (median 19 kg ha⁻¹ yr⁻¹), respectively. The respective ranges in conjunction with current land cover, cropping and stocking but corrected for the potential impact of on-farm sediment mitigation measures were up to 1315 kg ha⁻¹ yr⁻¹ (median 50 kg ha⁻¹ yr⁻¹) and 1269 kg ha⁻¹ yr⁻¹ (median 8 kg ha⁻¹ yr⁻¹). Multiplication of the estimates of excess sediment loss corrected for current measure uptake, above TMBSDR and MMBSDR, with estimated maximum unit damage costs for the detrimental impacts of sediment pollution on ecosystem goods and services, suggested respective water body ranges up to 495 £ ha⁻¹ yr⁻¹ and 478 £ ha⁻¹ yr⁻¹. Nationally, the total loss of sediment in excess of TMBSDR was estimated at 1,389,818 t yr⁻¹ equating to maximum environmental damage costs of £523 M yr⁻¹, due to current structural land use, compared to 1,225,440 t yr⁻¹ equating to maximum damage costs of £462 M yr⁻¹ due the uptake of on-farm sediment control measures. The corresponding total loss of sediment in excess of MMBSDR was estimated at 1,038,764 t yr⁻¹ equating to maximum damage costs of £462 M yr⁻¹, compared with 890,146 t yr⁻¹ and £335 M yr⁻¹ correcting excess agricultural sediment loss for current implementation of abatement measures supported by policy instruments. This work suggests that the current uptake of sediment control measures on farms across England and Wales is delivering limited benefits in terms of reducing loadings to rivers and associated environmental damage costs.     

Quantification and valuation of ecosystem services in diverse production systems for informed decision-making

The empirical evidence of decline in ecosystem services (ES) over the last century has reinforced the call for ES quantification, monitoring and valuation. Usually, only provisioning ES are marketable and accounted for, whereas regulating, supporting and cultural ES are typically non-marketable and overlooked in connection with land-use or management decisions. The objective of this study was to quantify and value total ES (marketable and non-marketable) of diverse production systems and management intensities in Denmark to provide a basis for decisions based on economic values. The production systems were conventional wheat (Cwheat), a combined food and energy (CFE) production system and beech forest. Marketable (provisioning ES) and non-marketable ES (supporting, regulating and cultural) ES were quantified by dedicated on-site field measurements supplemented by literature data. The value of total ES was highest in CFE (US$ 3142 ha⁻¹ yr⁻¹) followed by Cwheat (US$ 2767 ha⁻¹ yr⁻¹) and beech forest (US$ 2328 ha⁻¹ yr⁻¹). As the production system shifted from Cwheat - CFE–beech, the marketable ES share decreased from 88% to 75% in CFE and 55% in beech whereas the non-marketable ES share increased to 12%, 25% and 45% of total ES in Cwheat, CFE and beech respectively, demonstrating production system and management effects on ES values. Total ES valuation, disintegrated into marketable and non-marketable share is a potential way forward to value ES and ‘tune’ our production systems for enhanced ES provision. Such monetary valuation can be used by policy makers and land managers as a tool to assess ES value and monitor the sustained flow of ES. The application of ES-based valuation for land management can enhance ES provision for maintaining the productive capacity of the land without depending on the external fossil-based fertilizer and chemical input.     

Life cycle greenhouse gases,energy and cost assessment of automobiles using magnesium from Chinese Pidgeon process

Magnesium (Mg) has a great potential to reduce vehicle weight, fuel consumption, and greenhouse gas emissions. The Chinese Mg industry has developed rapidly since the 1990s. The output of Mg reached 700,000 tons in 2006, accounting for more than 70% of global Mg production. Most of Mg is produced in China through the Pidgeon process that has an intensive energy usage and generates a large amount of greenhouse gas (GHG) emissions, which may offset the potential advantage of using Mg parts in automobiles. It is critical to quantify the energy usage and GHG emissions through entire life cycle when the Mg are applied to automobiles. It is also essential to evaluate cost implications of the Mg parts application in automobiles and ensure it to be cost competitive. The objectives of this study are (1) Build a life cycle inventory (LCI) of Mg produced by Pidgeon process; (2) Establish an LCA model that can evaluate GHG emissions and energy usage for the Mg automotive application; (3) Estimate the cost implications of the Mg parts application in automobiles.An Mg LCI was built based on interviews and surveys and the GREET model was adapt for this study. The results indicated that, for each kilogram of Mg produced by Pidgeon process, GHG emissions and energy usage would be 27 kg CO₂eq and 280 MJ, which are five times higher than steel production. Replacing steel with 82 kg Mg on a base automobile would lower curb weight by 5.7%, but only reduce life cycle GHG emissions and energy usage by 0.8% and 1.3%. Scenario analyses indicated that potential reduction of life cycle GHG emissions and energy usage could reach to 15%, if secondary weight saving and a smaller engine were included. Cost analyses also show 18% reduction when the additional weight saving and a smaller displacement engine were included, under a 100,000 km driving distance and gasoline price at $1.0/l.