交联壳聚糖／Cu2O复合颗粒可见光催化脱色活性艳红

利用壳聚糖对金属离子的吸附和螯合作用，通过简单的液相沉淀一还原过程一步原位合成了交联壳聚糖／Cu2O复合粒子。x射线衍射（XRD）和红外（FT—IR）测试结果表明，壳聚糖与Cu2O纳米微粒能有效复合。以活性艳红X-3B溶液为模拟印染废水，采用Langmuir-Hinshelwood假一级方程模拟交联壳聚糖／Cu2O复合粒子光催化脱色反应的动力学行为，从动力学角度系统研究染料初始浓度、反应体系pH、催化剂用量和反应体系气氛等因素对复合粒子可见光催化脱色反应速率的影响。结果表明，当染料溶液浓度较低时，光催化过程可视为假一级反应。降低活性艳红X-3B初始浓度和pH，增加催化剂用量和反应体系的含O2量都可显著增加光解脱色反应速率常数。相同条件下，与纯Cu2O相比，交联壳聚糖／Cu2O复合粒子对X-3B呈现出更好的吸附性和更高的可见光催化活性。     

氧化亚铜光催化降解活性艳红的研究

制备了纳米SiO2-Cu2O复合氧化物,并对其进行表征。研究了SiO2-Cu2O在可见光照射下光催化降解活性艳红X-3B的性能。考察了催化剂组成、活性艳红浓度、催化剂用量、H2O2等对光催化反应的影响,还研究了Cu2O光催化反应动力学。结果表明,用SiO2摩尔含量为2%的SiO2-Cu2O光催化降解活性艳红,反应4 h,活性艳红降解率达到85%,降解反应为一级反应。     

壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B动力学研究

采用仿生矿化法制备了壳聚糖/纳米CdS复合颗粒光催化剂,并用于可见光光催化降解猩红B染料模拟废水,研究了猩红B初始浓度、pH、催化剂投加量和催化剂重复使用次数等因素对猩红B光催化降解的影响.X射线衍射(XRD)分析表明,壳聚糖能有效负载CdS纳米微晶.采用Langmuir-Hinshelwood模型描述壳聚糖/纳米CdS复合颗粒可见光光催化降解猩红B反应动力学行为,在猩红B初始质量浓度较低(≤20 mg/L)时,光催化降解过程符合假一级动力学方程.降低猩红B初始浓度和溶液pH都可显著增大光催化降解速率常数;催化剂投加量小于0.7 g/L时,光催化降解速率随其增加而增大,但催化剂投加量过大会使光催化降解速率减小;催化剂重复使用第5次时,猩红B光催化降解速率常数仍为第1次使用时的63.4%.     

剩余污泥催化剂的制备及其脱色性能

以焦化废水脱水污泥为载体、ZnCl2为活化剂和催化剂的活性组分,采用一步法制备污泥催化剂。实验结果表明,当ZnCl2浓度为4 mol/L、固液比1∶3、焙烧温度550℃、焙烧时间40 min时,制备的污泥催化剂对亚甲基蓝的脱色性能最佳。利用制备的催化剂对活性红X-3B、弱酸性艳红B、活性蓝X-BR溶液进行脱色处理,研究反应时间、染料浓度、溶液pH、催化剂投加量和H2O2用量对染料脱色性能的影响。最佳条件下,3种废水的脱色率分别达到90.7%、97.5%和94.4%。对脱色数据进行动力学模拟,结果表明,3种染料废水脱色反应分别符合二级动力学模型、一级动力学模型、二级动力学模型。     

仿生矿化法制备壳聚糖/纳米CdS复合粒子对猩红B光催化降解研究

用仿生矿化法制备了壳聚糖/纳米CdS复合粒子，并用于可见光光催化降解猩红B染料模拟废水，系统地研究了染料初始浓度、pH值、催化剂投加量、光照情况和催化剂重复使用等因素对猩红B的光解脱色效率的影响。结果表明，当pH=3.0，催化剂投加量为0.7 g/L的条件下，对初始溶液为20 mg/L的猩红B模拟废水，60 min之内脱色率超过96%。酸性媒介比碱性媒介更有利于猩红B染料光解脱色。实验范围内Br^-、NO^-₃和Cl^-等无机阴离子，均对降解脱色有促进作用，其中NO₃^-对脱色作用促进最显著。处理前后的UV-Vis谱图分析表明猩红B在壳聚糖/纳米CdS复合粒子可见光光解处理过程中脱色是因为染料发生氧化光降作用。催化剂重复利用5次后，处理60 min对猩红B的脱色率仍可达到80.7%。     

壳聚糖在固定化光合细菌处理染料活性艳红X-3B中的应用研究

采用海藻酸钠对光合细菌进行包埋,并在固定化过程中加入壳聚糖,研究添加了壳聚糖的固定化细胞在不同条件下对活性艳红X-3B的脱色效果及其降解动力学.实验结果表明,在厌氧条件下,X-3B的脱色效果较好;染料浓度在30～300 mg/L之间变化时,厌氧降解动力学方程均符合一级动力学方程;降解速率与染料初始浓度之间关系符合Michaelis-Menten方程,反应动力学参数Km=374.96 mg/L,Vmax=7.53 mg/L·h.振荡有利于脱色并使半衰期缩短;固定化小球可重复使用.     

光助非均相Fenton体系用于活性艳红X-3B脱色的研究

在光助非均相Fenton体系中，采用一种稀土铈-铁复合(Ce-Fe)材料作为催化剂，并探讨了该反应体系在不同条件下活性艳红X-3B的脱色效果。结果表明：该光助非均相Fenton反应在前10min符合一级反应动力学。采用掺杂0．08mol／L铈制备的Ce-Fe材料对活性艳红X-3B具有最佳的脱色效果，在pH3．0、H2O234mg／L、UV253．7nm条件下，10min内该反应体系速率常数％达到0．2456min^-1，明显高于相同条件下的UV／H2O2(0．0446min^-1)、UV／Ce-Fe(0．0306min^-1)体系的速率常数。     

光助非均相Fenton体系用于活性艳红X-3B脱色的研究

在光助非均相Fenton体系中,采用一种稀土铈铁复合(CeFe)材料作为催化剂,并探讨了该反应体系在不同条件下活性艳红X3B的脱色效果。结果表明:该光助非均相Fenton反应在前10min符合一级反应动力学。采用掺杂0.08mol/L铈制备的CeFe材料对活性艳红X3B具有最佳的脱色效果,在pH3.0、H2O234mg/L、UV253.7nm条件下,10min内该反应体系速率常数k达到0.2456min-1,明显高于相同条件下的UV/H2O2(0.0446min-1)、UV/CeFe(0.0306min-1)体系的速率常数。     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

高压电弧放电处理偶氮染料废水

用高压电弧放电产生的低温等离子体对含偶氮染料的废水进行了处理，以甲基橙为例研究了电压幅值、处理时间、溶液初始浓度、溶液初始pH值、投加Fe^2＋和Fe^3＋对染料脱色的影响。实验结果表明，甲基橙浓度为50mg／L时其降解率随时间和电压幅值的增加而增加。溶液初始浓度对染料去除效果影响较为明显，同等条件下初始浓度越低降解率越高。酸性条件下有利于低温等离子体处理甲基橙。Fe^2＋和Fe^3＋对低温等离子体降解甲基橙有一定的催化作用。电压8kV处理3min，Fe^2＋为20mg／L时去除率由89．64％增至99．72％。Fe2（SO4），的最佳投加量为5mg／L（以Fe^3＋计），而FeCl，的最佳投加量为80mg／L（以Fe^3＋计）。     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂，以20 W紫外灯为光源，在自制的光催化反应器中降解活性艳红K-2BP，考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明，当溶液初始浓度为60 mg/L，催化剂投加量为12 g/L，通气量为1 200 mL/min，光照2.5 h，活性艳红K-2BP的降解率可达99.2%；H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时，光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示，LZTZ光催化剂可有效降解印染废水。     

Photocatalytic degradation of Reactive Red 195 using anatase/brookite TiO2 mesoporous nanoparticles: Optimization using response surface methodology (RSM) and kinetics studies

In the present study, the photocatalytic degradation of Reactive Red 195 (RR195) from aqueous samples under UV-A irradiation by using anatase/brookite TiO₂ (A/B TiO₂) mesoporous nanoparticles has been investigated. Batch experiments were conducted to study the effects of the main parameters affecting the photocatalytic process. The effects and interactions of most influenced parameters, such as substrate concentration and catalyst load, were evaluated and optimized by using a central composite design model and a response surface methodology. The results indicated that the dye degradation efficiency in the experimental domain investigated was mainly affected by the tested variables, as well as their interaction effects. Analysis of variance showed a high coefficient of determination value (R ²?=?0.9947), thus ensuring a satisfactory adjustment of the first-order regression model (2FI model) with the experimental data. The obtained results also indicate that catalyst loading plays an important role in determining the removal efficiency of RR195 attributable to both photodegradation and adsorption process. Under optimal conditions (initial dye concentration (50 mg/L) and catalyst loading (2,000 mg/L), A/B TiO₂ showed similar removal efficiency compared to that of commercial titania (Degussa P25). Also, at these conditions, complete degradation of RR195 can be achieved by both catalysts within 15 min under UV-A irradiation. The experiments demonstrated that dye removal on the prepared A/B TiO₂ was facilitated by the synergistic effects between adsorption and photocatalysis. Photocatalytic mineralization of RR195 was monitored by total organic carbon. The recycling experiments confirmed the stability of the catalyst.     

高铁酸盐对活性及分散染料的脱色研究

采用湿法制备了高铁酸钾(K₂FeO₄)氧化剂，研究了其对染料活性艳红X-3B(X-3B) 和分散蓝2BLN(2BLN)在不同pH条件下的脱色效果，并对Al₂ (SO₄)₃、K₂FeO₄及O₃对活性及分散染料的脱色效果进行了比较。结果表明：高铁酸钾对活性及分散染料的脱色效果明显， X-3B脱色率随pH的增加不断提高，2BLN脱色率在pH 6～10范围内无明显变化，在pH＝5时达到最大值。在X-3B及2BLN浓度同为100 mg／L，pH分别为10、5， K₂FeO₄浓度分别为100 mg／L和200 mg／L时，BLN及X-3B的脱色率分别达到92.3％和87.3％。在相同条件下，K₂FeO₄对活性艳红X-3B的脱色效果好于Al₂(SO₄)₃和O₃； 而K₂FeO₄对分散蓝2BLN的脱色效果虽比Al₂ (SO₄)₃稍差，但比臭氧的脱色效果要好。同时还研究了K₂FeO₄对活性及分散染料的脱色机理，结果表明： 高铁酸钾对X-3B的脱色依赖于K₂FeO₄的氧化作用，而对的2BLN的脱色则以絮凝为主。     

Solar photocatalysis for treatment of Acid Yellow-17 (AY-17) dye contaminated water using Ag@TiO2 core–shell structured nanoparticles

Wastewater released from textile industries causes water pollution, and it needs to be treated before discharge to the environment by cost effective technologies. Solar photocatalysis is a promising technology for the treatment of dye wastewater. The Ag@TiO₂ nanoparticles comprising of Ag core and TiO₂ shell (Ag@TiO₂) have unique photocatalytic property of inhibition of electron–hole recombination and visible light absorption, which makes it a promising photocatalyst for use in solar photocatalysis and with higher photocatalytic rate. Therefore, in the present work, the Ag@TiO₂ nanoparticles synthesized by one pot method with postcalcination step has been used for the degradation of Acid Yellow-17 (AY-17) dye under solar light irradiation. The Ag@TiO₂ nanoparticles were characterized using thermogravimetric–differential thermal analysis, X-ray diffraction, transmission electron microscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The catalyst has been found to be very effective in solar photocatalysis of AY-17, as compared to other catalysts. The effects of pH, catalyst loading, initial dye concentration, and oxidants on photocatalysis were also studied. The optimized parameters for degradation of AY-17 using Ag@TiO₂ were found to be pH?3, dye/catalyst ratio of 1:10 (g/g), and 2 g/L of (NH₄)₂S₂O₈ as oxidant. Efficient decolorization and mineralization of AY-17 was achieved. The kinetics of color, total organic carbon, and chemical oxygen demand removal followed the Langmuir–Hinshelwood model. Ag@TiO₂ catalyst can be reused thrice without much decline in efficiency. The catalyst exhibited its potential as economic photocatalyst for treatment of dye wastewater.     

Effect of factors on decolorization of azo dye methyl orange by oxone/natural sunlight in aqueous solution

Purpose  

The oxone process for azo dye decolorization has drawbacks such as difficulties with reuse, risks of secondary pollution, and high costs associated with UV irradiation. This study aims to explore the use of oxone for decolorization in the absence of catalyst and under natural sunlight conditions (i.e., oxone/natural sunlight system) and evaluate the impacts of operating parameters (reagent dosage, initial methyl orange (MO) concentration, and initial pH) and coexisting substances (humic acid, NO₃⁻, metal ions) on the system’s decolorization efficiency.