A comparative analysis of wind resource parameters using WAsP and windPRO

This paper investigates the accuracy of the wind resource estimation for a site in a central India region using a latest licensed version of WAsP 11 and windPRO 3.1. Whole one year measured met mast wind data has been taken using anemometer and wind vane at 10 m and 25 m height, respectively above ground level. The digitized elevation and roughness model of the corresponding site shows the roughness class 4 (roughness length 1.2525 m). The wind data has been extrapolated up to 80 m height by using power and log law models which provide the power density near about 120 W/m². As per the micro sitting guidelines for the virtual wind farm installation 5D X 7D mapping has been selected which Indicates the total power output by installing 8 Vestas V-90 1.8 MW wind turbine from WAsP is 31.561 GWh and from windPRO is 28.083 GWh.     

Wind energy potential analysis for Thailand: Uncertainty from wind maps and sensitivity to turbine technology

Rapid development of wind energy has been witnessed in Thailand. However, different wind resource maps (over land) have brought great uncertainty to wind energy planning. Here, four important mesoscale wind maps were considered: DEDP (2001), World Bank (2001), Manomaiphiboon et al. (2010) of JGSEE, and DEDE (2010). The wind maps were first harmonized to a common grid at 100 m and then compared. The earlier wind maps (DEDP and World Bank) are shown to represent the lower and upper limits of predicted speed, respectively, while JGSEE and DEDE tend to be more moderate with predictions statistically closer to observations. A consolidated wind map was constructed based on their median and shown to have the best prediction performance. It was then used for the technical potential analysis, in which three large (2-MW) turbine models (two conventional and one designed for low wind speed) were considered. By GIS techniques, any land areas not feasible for large wind turbines were excluded, and the corresponding overall onshore technical potential ranges between 50 and 250 GW, depending on map and turbine model. Considering only economically feasible turbines (with capacity factors of 20%) and the median-based map, the final technical potential equals 17 GW when using the low-wind-speed model but is reduced to 5 GW with the conventional models, adequately meeting the national wind energy target of 3 GW by the year 2036. The results suggest a strong sensitivity of estimated technical potential to turbine technology and a suitability of low-wind-speed turbines for wind conditions in Thailand.     

Climate,land, energy and water (CLEW) interlinkages in Burkina Faso: An analysis of agricultural intensification and bioenergy production

This paper discusses climate, land, energy and water (CLEW) interactions in Burkina Faso. It shows that integrated assessments of resource use at the national level can provide important insights and benefits, especially for a resource constrained least developed country. Agricultural policy is shown to have strong implications for energy use, whereas energy policies are found to be strongly interrelated with water constraints. Without an integrated and coordinated approach, strategy and policy formulation efforts to increase energy, food and water security could become both incoherent and counter‐productive.     

An Analysis of the Wind Energy Potential of Elazig,Turkey

Abstract

In this study, the wind energy potential of Elazig is statistically analyzed based on hourly measured wind speed data over the five-year period from 1998 to 2002. The probability density distributions are derived from cumulative distribution functions. Two probability density functions are fitted to the measured probability distribution on a yearly basis. The wind energy potential of the location is studied based on the Weibull and Rayleigh distributions. It was found that the numerical values of both Weibull parameters (k and c) for Elazig vary over a wide range. The yearly values of k range from 1.653 to 1.878 with an average value of 1.819, while those of c are in the range of 2.757–2.994 m/s with an average value of 2.824 m/s. In addition, yearly mean wind speed and mean power density of Elazig is found as 2.79 m/s and 38.76 W/m², respectively. The wind speed distributions are represented by Weibull distribution and also by Rayleigh distribution, with a special case of the Weibull distribution for k = 2. As a result, the Rayleigh distribution is found to be suitable to represent the actual probability of wind speed data for Elazig.     

A case study of an isolated wind powered electricity system meeting 100% of local demand

Using meteorological and electricity demand data for a 4-year period, electricity demand in Shetland was modeled to provide an estimate of the demand over a 30-year period from 1 January 1981. That modeled demand was then compared to estimated wind power output over the same period using the WAsP model. The wind farm output was estimated for a range of sizes of wind farm up to the consented 370 MW Viking Wind Farm in Shetland. Some wind power was available for 94% of the time and the 370 MW wind farm would meet 100% of demand for nearly 80% of the time. The statistics of single and accumulated deficits were calculated for a range of wind farms and estimates of the amount of additional generation capacity and additional power requirements were assessed. The study suggests that with storage, wind power in Shetland could meet all electricity demand in Shetland at around £130 to £150/MWh (excluding subsidy) and with a grid connection allowing the sale of excess power, those costs could be reduced.     

RETROFIT OF HYDROPOWER CAPACITY AT CONEMAUGH DAM1

ABSTRACT: This paper describes a preliminary investigation of the hydropower potential at the existing Conemaugh Dam, a U.S. Army Corps of Engineers project located in the Kiskiminetas River Basin, Pennsylvania. The objective of the study was to determine the most cost effective layout of power production facilities for each of four possible installed capacities. Based on preliminary cost estimates and monthly power production computations, a layout using standard tube turbines in a powerhouse constructed on the face of the emergency spillway would produce the cheapest energy at a capacity of 8 to 10 megawatts (MW).     

Wind power potential assessment for three buoys data collection stations in the Ionian Sea using Weibull distribution function

The present article utilizes wind measurements from three buoys data collection stations in Ionian Sea to study the wind speed and power characteristics using the Weibull shape and scale parameters. Specifically, the site dependent, annual, and monthly mean patterns of mean wind speed, Weibull parameters, frequency distribution, most probable wind speed, maximum energy carrying wind speed, wind power density and wind energy density characteristics have been analyzed. The Weibull distribution was found to represent the wind speed distribution with more than 90% accuracy, in most of the cases. Moreover, the correlation between the percentages of times the wind speed was above cut-in-speed and the measured mean wind speed for the three selected sites, as the correlation between the aforementioned percentages and the scale parameter c were examined and were found linear. At all these sites, no definite increasing or decreasing trends in annual mean wind speed values could be detective over the data reporting period. The mean values of wind speed, scale parameter, most probable wind speed, maximum energy carrying wind speed, wind power and wind energy density values showed higher values during winter time and lower in summer time in Pylos and Zakynthos. Moreover, Pylos and Zakynthos were found to be the best sites from wind power harnessing point of view.     

Use of seasonal precipitation forecasting to improve agricultural production in the Sudano-Sahel: an institutional analysis of Burkina Faso

Climate forecasts of the total rainfall in the Sudano-Sahelian region of West Africa may have sufficient value to assist in agricultural decision-making at the national, regional and local level. Forecasts are produced in both international and national centres using a variety of techniques. Institutions in Burkina Faso, the focus of the present case study, that are involved in agro-meteorology and agriculture are interested in using forecasts. They have requested many improvements in the forecasts—some of which are beyond the state of the art. The research for the present article, based on interviews with representatives of institutions and following the trail of other agro-meteorological information, confirms the existence of an information network within Burkina Faso that could reasonably well disseminate climate forecasts to interested organizations, farmers, and pastoralists.     

Wind energy potential assessment and techno-economic performance of wind turbines in coastal sites of Buenos Aires province,Argentina

An assessment of wind energy potential was carried out in five sites (four onshore and one offshore) in South-West (SW) of Buenos Aires province (Argentina). We use high-resolution wind data (2 and 5 min) for the period 2009–2012. The power law was used to estimate the wind speed at 30, 40, and 60 m height from the anemometer position. Turbulence intensity and wind direction were analyzed. Statistical analyses were conducted using two-parameter Weibull distribution. A techno-economic analysis based on a set of commercial wind turbines was performed in those sites. The results derived from this work indicate that the SW of Buenos Aires province represents a promising area for the wind energy extraction, which would encourage the construction of wind farms for electricity generation.     

Disruption to place attachment and the protection of restorative environments: A wind energy case study

Deepening understanding of public responses to large-scale renewable energy projects is of academic and practical importance, given policies to lessen fossil fuel use in many countries. Although the NIMBY (Not In My Back Yard) concept is commonly used to explain public opposition, the concept has been extensively critiqued. This study applies an alternative approach based upon the notion of disruption to place attachment, and the theory of social representations, with a focus upon the symbolic meanings associated with a proposed project and the places affected by it. Empirical data is provided from a case study of a proposed 750 MW offshore wind farm in North Wales, using group discussions and questionnaires distributed to local residents in two coastal towns (n = 488). Results indicate significant differences between each town's residents in their responses to the project, and how opposition arises from nature/industry symbolic contradictions: between a place represented in terms of scenic beauty that provides a restorative environment for residents and visitors, and a wind farm that will industrialise the area and ‘fence’ in the bay. In one of the towns, the data suggests that contradiction between project and place was experienced as a threat to identity for those with strong place attachment, leading to negative attitudes and oppositional behaviour. Levels of trust in key actors moderated the relation between place attachment and negative attitudes to the wind farm. The results provide further evidence of the role of place attachment in shaping so-called ‘NIMBY’ responses to development proposals, and challenge the assumption that offshore wind farms will prove less controversial than those onshore.     

Wind energy development in California,USA

Windfarms have been developed rapidly in California in the last few years. The impetus has been a legislated goal to generate 10% of California's electricity by windpower by the year 2000, and generous state and federal tax incentives. Windpower is promoted as environmentally benign, which it is in traditional uses. The California program, however, is not traditional: it calls for centralized development of a magnitude sufficient to offset significant amounts of fossil fuels now used to generate electricity.Centralized windfarm development, as exemplified by the Altamont Pass, Tehachapi Mountains, and San Gorgonio Pass developments, involves major road building projects in erosion-sensitive terrain, effective closure of public lands, and other detrimental effects. A windfarm consisting of 200 turbines with 17-m rotors located in steep terrain 16 km from an existing corridor might occupy 235 ha and physically disturb 86 ha. With average annual wind speeds of 22.5 km/h, the farm would generate about 10×10⁶ kWh/year at present levels of capacity. This annual production would offset 1% of one day's consumption of oil in California. To supply 10% of the state's electricity (at 1984 production rates) would require about 600,000 turbines of the type in common use today and would occupy more than 685,000 ha. It is likely that indirect effects would be felt in much larger areas and would include increased air and water pollution resulting from accelerated erosion, degradation of habitat of domestic and wild animals, damage to archaeological sites, and reduction of scenic quality of now-remote areas of the state.     

西藏农村能源消费及环境影响研究

西藏农村人口现有220多万,占全区总人口80％以上,农村经济落后,城乡差距很大。西藏农村能源资源主要有水力、地热、太阳能、风力、林木和畜粪等,煤炭、石油、天然气等高热值的优质能源很少。在这种经济发展水平及能源资源基础条件下,农村能源消费中高热值的现代能源比重很低,主要以生物质能如薪柴、牛粪、草皮等为主。这种低水平的能源消费结构已经对西藏脆弱的生态环境造成了巨大的破坏,西藏未来的能源发展战略迫切需要改变农村目前的消费结构,应发展太阳能、风能、农村小水电及输入高热值的化石能源替代目前生物质能的消费,减少因能源消费对西藏生态环境的破坏。     

Worldwide Tidal Current Energy Developments and Opportunities for Canada's Pacific Coast

Recent rapid advances of tidal current energy extraction (TCEE) technologies and resource analyses suggest in excess of 20,000 GWh/annum of electricity may be realistically exploitable in the near term off Canada's West Coast. Moreover, because tidal currents have a semi-diurnal (or, in some locations, diurnal) periodicity, and can be predicted and quantified on a spatial and temporal basis, this resource confers a distinct advantage over most other renewables, and, therefore, may achieve supply security.

In this study, TCEE technologies are assessed on the basis of energy delivered, environmental intrusion and economic viability. As such, relevant issues including resource characteristics, site selection, conversion efficiencies, capacity factors, power densities, hydrodynamic feedbacks, and grid integration are addressed.     

Thermoeconomic installation limit of PV/WT hybrid energy systems for Off-grid islands

An ideal off-grid island can become 100% energy-sufficient if one installs renewable energy systems such as solar photovoltaic (PV) and wind turbine (WT) systems. However, the intermittent and uncertain nature of the power supply from renewable energy systems hinders a 100% autonomy level (AL) without an infinite energy storage capacity. The thermoeconomic installation limit (TEIL) of a PV/WT hybrid energy system was studied using hourly weather data and the energy demand profile for off-grid islands. An appropriate battery size for the TEIL was also determined. Given the current installation cost of the hybrid energy system and the battery unit, the AL for a PV/WT hybrid energy system at the TEIL is calculated to be approximately 70%. Above the limit, the size of the energy storage unit and, correspondingly, the total annual cost of the PV/WT hybrid energy system increase sharply.     

Investigations on Blade Tip Tilting for Hawt Rotor Blades Using CFD

The main purpose of this paper is to study the aerodynamic effects of blade tip tilting on power production of horizontal-axis wind turbines by using Computational Fluid Dynamics (CFD). For validation and as a baseline rotor, the NREL Phase VI wind turbine rotor blade is used. The Reynolds-Averaged Navier–Stokes Equations are solved and different turbulence models including the Spalart–Allmaras, Standard k-?, k-? Yang–Shih and SST k–ω models are used and tested. The results are shown in terms of power generation at different wind speeds and the pressure distribution at different sections of the blade, and the comparisons are made with the available experimental data. For tip tilting analysis, 16 different geometries belonging to four different configurations are studied. The geometries are generated based on changing the twist and the cant angles of the winglet. The four different configurations are obtained from tilting the blade tip toward pressure side, suction side, leading edge, and trailing edge. The effect of the different configurations on the flow characteristics and hence on the power production of the wind turbine is investigated.     

Optimization of a Wind/PV Hybrid Power Generation System

This study investigates the wind and solar electricity generation availability at the Solar Energy Institute of Ege University, Izmir, Turkey. The main purpose of this study is to design an appropriate wind-PV hybrid system to cover the electricity consumption of the Institute. In order to do this, monthly average solar irradiation and wind speed data are used, which were measured, consisting of hourly records over an eight-year period from 1995–2002. Simple models were developed to determine wind, solar, and hybrid power resources per unit area. Correlations between the solar and wind power data were carried out on an hourly, daily, and monthly basis. It is shown that the hybrid system can be applied for the efficient and economic utilization of these resources.     

Adoption Potential of Conservation Agriculture Practices in Sub-Saharan Africa: Results from Five Case Studies

Despite the reported benefits of conservation agriculture (CA), its wider up-scaling in Sub-Saharan Africa (SSA) has remained fairly limited. This paper shows how a newly developed qualitative expert assessment approach for CA adoption (QAToCA) was applied to determine its adoption potential in SSA. CA adoption potential is not a predictor of observed adoption rates. Instead, our aim was to systematically check relevant factors that may be influencing its adoption. QAToCA delivers an assessment of how suitable conditions “and thus the likelihood for CA adoption” are. Results show that the high CA adoption potentials exhibited by the Malawi and Zambia case relate mostly to positive institutional factors. On the other hand, the low adoption potential of the Zimbabwe case, in spite of observed higher estimates, is attributed mainly to unstable and less secured market conditions for CA. In the case of Southern Burkina Faso, the potential for CA adoption is determined to be high, and this assessment deviates from lower observed figures. This is attributed mainly to strong competition of CA and livestock for residues in this region. Lastly, the high adoption potential found in Northern Burkina Faso is explained mainly by the fact that farmers here have no alternative other than to adopt the locally adapted CA system—Zaï farming. Results of this assessment should help promoters of CA in the given regions to reflect on their activities and to eventually adjust or redesign them based on a more explicit understanding of where problems and opportunities are found.     

Large-scale baseload wind power in China

This paper presents a novel strategy for developing wind power in large-scale (multi-GW) wind farms in China. It involves combining oversized wind farms, large-scale electrical storage and long-distance transmission lines to deliver 'baseload wind power' to distant electricity demand centers. Baseload wind power is typically more valuable to the electric utility than intermittent wind power, so that storage can be economically attractive even in instances where the cost per kWh is somewhat higher than without storage.
The prospective costs for this approach to developing wind power are illustrated by modifying an oversized wind farm at Huitengxile, Inner Mongolia. The site has an average power density of 580 W/m² at 50 m hub heights and is located 500 km north of Beijing. Using locally mass-produced wind turbines there are good prospects that wind power would be cost-competitive with coal power, on a lifecycle cost basis, while providing substantial net environmental benefits.
Finally, the institutional challenges related to the prospect of large-scale wind energy development are addressed. Especially important are policies aimed at developing the capacity for mass production of as much of this technology in China as is feasible. Promising instruments for speeding up the introduction of this technology include: (i) international joint ventures between foreign vendors and developers and Chinese manufacturers; and (ii) wind resource development concessions.     

Performance evaluation of a horizontal axis wind turbine in operation

The operation of modern horizontal axis wind turbine (HAWT) includes a number of important factors, such as wind power (P), power coefficient (C_P), axial flow induction factor (a), rotational speed (Ω), tip speed ratio (λ), and thrust force (T). The aerodynamic qualities of these aspects are evaluated and discussed in this study. For this aim, the measured data are obtained from the Sebenoba Wind Energy Power Plant (WEPP) that is located in the Sebenoba region in Hatay, Turkey, and a wind turbine with a capacity of 2 MW is selected for evaluation. According to the results obtained, the maximum turbine power output, maximum power coefficient, maximum axial flow induction factor, maximum thrust force, optimum rotational speed, probability density of optimum rotational speed, and optimum tip speed ratio are found to be 2 MW, 30%, 0.091, 140 kN, 16.11 rpm, 46.76%, and 7, respectively. This study has revealed that wind turbines must work under optimum conditions in order to extract as much energy as possible for approaching the ideal limit.     

Electromagnetic fields and other physical factors around wind power generators (pilot study)

According to the 20/20/20 strategy by European Union for green energy by 2020 priority should be given to the Renewable Energy Sources. The energy generated from the wind has proven to be of interest for several reasons—wind is available, it is a cheap, and virtually inexhaustible source of energy. In this relation in the last years, many wind power stations were built all around the country. They are being located in proximity of populated areas. Their work besides the generation of electricity is connected to emission of physical factors in the environment that could be essential for human health. In order to avoid overexposure to electromagnetic fields, noise, and vibration to the general public minimal safety distance is being determined theoretically for ‘worst case” conditions basing on the technical characteristics of the generators. After the mounting of installations, measurements have to be performed to determine whether the national and European safety limits for the factors of environment are being kept. The paper presents results of measurement of electromagnetic fields, additionally noise and vibration around one of the biggest wind power parks in Bulgaria. The measurements were made in the close proximity of the generators both for the personnel working conditions and for the population in the closest living areas.