A carbon-13 method for evaluating degradation of starch-based polymers

A new method for evaluating biodegradability of starch-based and certain other polymer blends uses the pre- and postexposure stable carbon isotope composition of material coupled with weight loss data to determine which components have degraded. The naturally occurring stable isotope of carbon.¹³C, is enriched in corn starch (¹³C, approx. –11) compared to petroleum-derived synthetic polymers (¹³C, approx. –32). Results on starch-synthetic polymer blends indicate that the ¹³C signatures of these blends are near-linear mixtures of their component ¹³C. Values of a ¹³C for starch-synthetic polymer blends exposed to biologically active laboratory soil and artificial seawater conditions are depleted in¹³C compared to unexposed samples, suggesting loss of the starch component. Combined with weight loss data for the exposed samples, the ¹³C values are statistically consistent with models requiring loss of the soluble component glycerin, followed by loss of starch, then petrochemical polymer, or simultaneous loss of starch and petrochemical polymer. Replicate ¹³C analyses of starch-synthetic polymer blends increase the statistical power of this relatively inexpensive, accessible technique to discriminate between degrading components.     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Remediation of Persistent Organic Pollutants Using a Novel Two-Phase Soil Washing Biosorption Process

A two-phase soil washing biosorption process was developed for the remediation of p,p-DDT-contaminated soil. The process involved desorption of contaminants from soil using dilute primary alcohols (40% 1-propanol) followed by contaminant removal from cosolvent solutions using fungal biosorption. Bench scale remediation studies were preformed to simulate ex situ (recycling experiment) or in situ (soil column study) treatment strategies. Both systems were effective at cleaning the soil to below Australian regulatory p,p-DDT levels. After 50–80 hours of soil washing, over 93% of p,p-DDT was removed from the soil(990 mg kg^-1 to <65 mg kg^-1) using either of these methods.p,p-DDT was removed from the cosolvent phase by sorption onto the fungal biomass. This resulted in only low levels of p,p-DDT remaining in the cosolvent solution(<1.5 mg l^-1). The application of both treatment strategies resulted in the rapid clean up of p,p-DDT-contaminated soil and the potential to recycle cosolvent solutions. The ability to recycle cosolvent solutions provides a mechanism for cost reductions of the remediation strategy.     

Correlating the Spatial Distribution of Atmospheric Ammonia with δ15N Values at an Ammonia Release Site

A field ammonia (NH₃) release experiment and open top chambers containing moorland monoliths continuously fumigated with NH₃ or sprayed with NH₄Cl were used to assess the potential for using ¹⁵N values in determining the area of influence around a point NH₃ emission source. ¹⁵N values are being increasingly used as environmental tracers and we tested the hypothesis that the ¹⁵N signal from an NH₃ emission source is observable in nearby vegetation. Using modified monitoring devices, atmospheric NH₃ concentrations were found to decrease with distance from source, with ¹⁵N values also reflecting this trend, producing a signal shift with changing concentration. Open top chamber studies of ¹⁵N values of Calluna vulgaris (L.) Hull indicated a correlation with deposition treatments in current year shoots. Analysis of Calluna shoots from the NH₃ release showed a similar trend of ¹⁵N enrichment. Significant linear correlations between ¹⁵N and percent N in plant material were found, both in the controlled conditions of the open top chambers and at the NH₃ release site, illustrating the possible use of this technique in N deposition biomonitoring.     

Synthesis of a block copolymer of poly(3-hydroxybutyrate) and poly(ethylene glycol) and its application to biodegradable polymer blends

A block copolymer {P[(R,S)-HB-b-EG]} of atactic poly[(R,S)-3-hydroxybutyrate] {P[(R,S)-HB]} and poly(ethylene glycol) (PEG) was prepared by the ring-opening polymerization of -butyrolactone in the presence of a macroinitiator (PEG/ZnEt₂/H₂O) which had been produced by the reaction of ,-dihydroxy PEG ( _n=3000) with ZnEt₂/H₂O (1/0.6) catalyst. The block copolymer ( _n=10,500, _w/ _n=1.2) was an A-B-A triblock copolymer comprising atactic P[(R,S)-HB] (A) and PEG (B) segments. The miscibility, physical properties, and biodegradability of binary blends of microbial poly[(R)-3-hydroxybutyrate] {P[(R)-HB]} with the block copolymer P[(R,S)-HB-b-EG] has been studied. The glass-transition temperature (T _g) data showed that the P[(R)-HB]/P[(R,S)-HB-b-EG] blend was miscible in the amorphous state. The P[(R)-HB] film became flexible and tough by means of blending with P[(R,S)-HB-b-EG] block copolymer. The enzymatic degradation of blend films was carried out at 37°C and pH 7.4 in a 0.1M phosphate solution of an extracellular PHB depolymerase fromAlcaligenes faecalis. The enzymatic degradation took place solely on the surface of the blend films.     

Carbon Molecular Sieving Membranes Derived from Lignin-Based Materials

Carbon molecular sieving membranes were prepared by pyrolysis of lignocresol derived from lignin by the phase-separation method. Lignocresol membranes formed by a dip process on a porous -alumina tubing were carbonized at 400–800°C under nitrogen atmosphere. The thickness of the membrane formed on the outer surface of the substrate was about 400 nm judging from SEM observation. Gas-evolving behavior of lignocresol was measured using thermogravimetry-mass spectrometry (TG-MS). The gaseous products evolved from lignocresol included a number of fragments with higher molecular weights; whereas those from phenolic resin are mainly due to phenol and methylphenol. These evolved pyrolysis fragments effectively contribute to micropore formation of carbonized lignocresol membranes. Gas permeation rates through the membrane decreased in the order of increasing kinetic molecular diameter of the penetrant gas, and the membrane behaved like a molecular sieve. The permeation properties were dependent on heating conditions, and a pyrolysis temperature of 600°C gave the best membrane performance. Gas selectivities of the membrane prepared at 600°C were 50, 8, 290, and 87 for CO₂/N₂, O₂/N₂, H₂/CH₄, and CO₂/CH₄ at 35°C, respectively.     

Effect of Crystalline and Amorphous Structures on Biodegradability of Poly(Tetramethylene Succinate)

The effect of orientation in the amorphous and crystalline regions on the biodegradability of PTMS [poly(tetramethylene succinate)] was studied using the amorphous orientation function, birefringence, and crystallinity. The crystalline and amorphous intrinsic lateral sonic moduli, E _t,c ⁰ and E _t,am ⁰ , were 2.61 × 10³ and 0.41 × 10³ MPa, respectively. Using the data on birefringence, crystalline and amorphous orientation function (f and f _am), crystallinity, and sonic modulus of the oriented PTMS fibers, the intrinsic birefringence of the crystalline ( _c ⁰ ) and amorphous ( _am ⁰ ) regions were evaluated to be 0.0561 and 0.0634, respectively. The biodegradabilities of oriented PTMS films were reduced as the elongation increased, i.e., the amorphous orientation increased. At low elongation (100 and 150%), however, biodegradabilities remained unchanged when the degradation test was performed in activated sludge, which was attributed to the amorphous orientation occurring even at 100% elongation, though the amorphous orientation direction was perpendicular to the fiber axis.     

Nature of Atmospheric Aerosols over the Desert Areas in the Asian Continent: Chemical State and Number Concentration of Particles Measured at Dunhuang,China

Measurements of aerosol were made in August and October 2001, and January 2002, at Dunhuang, China (40°00N, 94°30E), to understand the nature of atmosphericparticles over the desert areas in the Asian continent. Balloon-borne measurements with an optical particle counter suggested that particle size and concentration had a noticeable peak in size range of super micron in not only the boundary mixing layer but also the free troposphere. Thickness of the boundary mixing layer, from distributions of particle concentration, was about 4 km in summer (17 August 2001), about2.5 km in fall (17 October 2001), and about 3 km in winter (11 January 2002), which suggest active mixing of particles near the boundary in summer. Number-size distribution of particleshowed a noticeable peak in the super micron particles size range inthe mixing boundary layer: 0.4–2 particles cm^-3 at diameter>1.2 m in summer, 0.05–4 particles cm^-3 at diameter >1.2 m in fall, and 0.1–5 particles cm^-3 at diameter>1.2 m in winter. In winter strong inversion of atmospherictemperature was found in the height range from the boundary to about 3 km and vertical distribution of particle concentration well corresponded with the temperature distribution. Chemical elements of individual aerosols, which were collectedin the boundary layer atmosphere at Dunhuang (18 October 2001) were analyzed with an electron microscope equipped with EDX. Thosesingle particle analysis suggested that most of the particles with supermicron size were soil particles, and those particles had littlesulfate on its surface. This is a very important different point,comparing with the chemical state of soil particles, which weretransported from the desert area of China to Japan, and showed frequentlythe existence of sulfate on the particle surface. Therefore, it isstrongly suggested that dust particles can be chemically modifiedduring their long-range transport from desert areas to Japan.     

The Effect of Nitrogen Enrichment on the Carbon Sink in Coniferous Forests: Uncertainty and Sensitivity Analyses of Three Ecosystem Models

Estimates of the global carbon sink induced by nitrogen enrichment range vary widely, from nearly zero to 2.3 Gt C year^-1. It is necessary to reduce this uncertainty if we are to make accurate predictions of the future magnitude of the terrestrial carbon sink. Here, we present a Monte Carlo approach to uncertainty and sensitivity analysis of three ecosystem models, Century,BGCand Hybrid. These models were applied to a coniferous forest ecosystem in Sweden. The best estimate of the change in total carbon content of the ecosystem with the cumulative change in nitrogen deposition over 100 years, C_total/N_deposition was 20.1 kg C (kg N)^-1 using the pooled mean, with a pooled standard deviation of 13.8 kg C (kg N)^-1. Variability in parameters accounted for 92% of the total uncertainty in C_total/N_deposition, and only 8% was attributable to differences between models. The most sensitive parameters were those which controlled the allocation of assimilate between leaves, roots and stem. In particular, an increase in allocation to fine roots led to a large reduction in C_total/N_deposition in all models, because the fine roots have a very high turnover rate, and extra carbon allocated there is soon lost through mortality and decomposition.     

The Role Played by Acetyl Group Distribution Patterns in Substituted Starch Toward Enzymatic De-acetylation and Chain Fragmentation

The nature and distribution of the acetylated groups were evaluated by ¹³C-NMR and ¹H-NMR. The starch substrate with a DS of 1.5 comprises only two patterns: -(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose. The starch with a DS of 3.0 also comprises two patterns: 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose and 2,3,6-tri-O-acetyl--(14)-d-glucopyranose; whereas starch (DS = 1.9) contains 4 patterns: 2,3,6-tri-O-acetyl--(14)-d-glucopyranose, 2,3,4,6-tetra-O-acetyl--(14)-d-glucopyranose terminal, 2,6-di-O-acetyl--(14)-d-glucopyranose, and 3,6-di-O-acetyl--(14)-d-glucopyranose. Using esterase from Viscozyme, it has been possible to hydrolyze up to 7% of the DS 3.0 starch. An -amylase (Fungamyl 800) was then added to these acetylesterases. With a 2.4 FAU/mL fraction of -amylase and 2.4 U/mL from the Viscozyme's acetylesterase, 28% of the acetylated end groups were hydrolyzed for the starch substrates with DS 3.0. Moreover, a synergic action between -amylase and acetylesterase was noticed, allowing fragmentation of 32% for DS 1.5, 30% for DS 1.9, and 11% for DS 3.0.     

Enzyme-Mediated Reactions of Oligosaccharides and Polysaccharides

Two types of enzymatic reactions are given here as examples of synthetic problems encountered in industry. In the first case, commercially available -D-galactosidase from Escherichia coli was used as a catalyst to transfer galactose from -lactose to oligosaccharides. A preference for galactosyl transfer to the 3- or 4-position of the sugar moiety of the oligosaccharide was observed for the products. As expected, only the -anomer was produced. A wide variety of sugars, including disaccharides, trisaccharides, cellotetraose, and maltodextrins, has been shown to act as acceptors, yielding oligosaccharides. In the second example, -galactomannan that had been previously treated to contain cationic groups (cationic guar gum) was subjected to treatment with a series of inexpensive commercial enzymes such as lipases, protease, and cellulases. Some enzyme preparations showed significant changes in the viscosities of 1% cationic guar solution. For example, lipases from Aspergillus niger and Aspergillus saitoi and protease XIII from Rhizopus niveus produced a substantial viscosity reduction (0–20% of original viscosity). These examples demonstrate the utility of low-cost enzymes in manipulating polymer structures.     

Deliquescence of Deposited Atmospheric Particles on Leaf Surfaces

A large fraction of deposited aerosol particles on leafsurfaces represents hygroscopic material in a high humidity environment, likely to become deliquescent within the water vapour transpired by the leaf. Microscopic observations on leaf surfaces of beech, kohlrabi and elder leaves grown in a particle-free environment and/or treated with defined particle load are presented. Spreading of deliquescent particles, formation of salt crusts, and encoating of and by waxes was observed. Deliquescence of NaNO₃ particles (deliquescence point 74% RH at 25 °C) was observed on and near the stomata at 35% relative humidity (RH) of the surrounding air, illustrating the influence of the boundary layer. Aerosols are difficult to identify on leaf surfaces, as similar patterns may be produced by deliquescent particles and processes like salt creep. These problems are especially important on leaves from the natural environment if only scanning electron microscopy (SEM) is used. These patterns could appear similar to the fused waxes described in forest decline research. Strong gradients are formed between deliquescent particles and the apoplastic solution within the leaf, promoting cuticular and stomatal uptake.     

The Application of Stable Isotopes for Assessing the Hydrological, Sulfur, and Iron Balances of Acidic Mining Lake ML 111 (Lusatia, Germany) as a Basis for Biotechnological Remediation

Stable isotope (¹⁸O–H₂O, ²H–H₂O ³⁴S–SO₄ ^2-) andhydrochemical data (SO₄ ^2-, Fe-concentrations) have beenused to estimate the annual groundwater inflow and outflow of mining lake ML 111 and to calculate the total amount of dissolvedsulfate and iron that is carried into the lake by groundwater. The hydrological balance suggests an annual groundwater inflow of 23 700 m³ and an annual groundwater outflow of 15 700 m³. The calculation of the sulfur and iron balances yielded an annual sulfate input of 37 800 kg and an annual iron input of 7000 kg with the groundwater inflow. Furthermore it was shown that significant fluxes of these elements go into the lake sediments which results in continuous release of acidity in the lake water.     

Three-Dimensional Numerical Simulation of Air Pollutant Dispersion in Street Canyons

The PHOENICS Computational Fluid Dynamics (CFD) software package has been used with a standard k- turbulence model to simulate the three-dimensional dispersion of air pollutants in an urban street canyon. In all cases, a vortex was formed within the street canyon, characterized by updrafts near the upwind buildings and down-drafts near the downwind buildings. Contours of pollutant concentrations over a transverse vertical plane at mid-canyon show pollutants circulating within the vortex, with higher concentrations at the leeward face than at the windward faces, and higher concentrations above downwind buildings than above upwind buildings. Longitudinal distributions of pollutant concentrations at leeward and windward faces are characterized by higher concentrations at mid-block and lower concentrations at the ends. These results agree qualitatively with previous wind tunnel findings such as those of Hoydysh and Dabberdt (1988) and Wedding et al. (1977). The results also suggest that the k- turbulence model is satisfactory for simulating the effect of turbulence on dispersion of pollutants in street canyons     

Synthesis and environmental degradation of polyesters based on poly (ε-caprolactone)

Poly (-caprolactone) (PCL), poly (-valerolactone) (PVL), poly (-caprolactone-co--valerolactone) [P(CL-co-VL)], and poly (-caprolactone-co-ethylene oxide-co--caprolactone) (PCL-PEO-PCL) were synthesized by ring-opening and diol-initiated polymerization of -caprolactone and -valerolactone. The degradation of the samples by chemical hydrolysis and in a soil burial test was evaluated. It was found that PCL, PVL, and P(CL-co-VL) degrade mainly enzymatically. The rate of degradation depends on their molecular weight, chemical structure, composition, and morphology. PCL-PEO-PCL block copolymers exhibit a repelling effect to the microorganisms in the soil, which depends on the molecular weight and relative amount of PEO block in the copolymer.     

Influence of Geometry on the Mean Flow within Urban Street Canyons – A Comparison of Wind Tunnel Experiments and Numerical Simulations

A comparison between numerical simulations and wind tunnel modelling has been performed to examine the variation with streamwise aspect ratio (width/height, W/H) of the mean flow patterns in a street canyon. For this purpose a two-dimensional (2-D) cavity was subjected to a thick turbulent boundary layer flow perpendicular to its principal axis. Five different test cases, W/H = 0.3, 0.5, 0.7, 1.0 and 2.0, have been studied experimentally with flow measurements taken using pulsed-wire anemometry. The results show that the skimming flow regime, with a large vortex in the canyon, occurred for all the cases investigated. For the cavities with W/H 0.7 a weaker secondary circulation developed beneath the main vortex. The narrower the canyon, the smaller the wind speed close to the cavity ground, giving increasingly poor ventilation qualities. The corresponding numerical results were obtained with the Computational Fluid Dynamics (CFD) code CHENSI that uses the standard k- model. The intercomparison showed good agreement in terms of the gross features of the mean flow for all the geometries examined, although some detailed differences were observed.     

A New Approach for the Flocculation Mechanism of Chitosan

A peak III/I ratio (_peak) in pyrene-fluorescence spectrum was used to measure the polarity of microenvironment of chitosan adsorbing pyrene molecules. The authors detected the pyrene-fluorescence spectrum of chitosan with different degrees of deacetylation (DD) and determined the relationship between the flocculation of bentonite colloid and the _peak of chitosan with a different molecular weight (MW) and DD. It can be concluded that MW rather than DD plays a key role in the flocculation and that bond bridging rather than charge neutralization dominates the flocculation with chitosan from a microenvironmental structure of view.     

Catalytic decomposition of hydrocarbon into hydrogen and carbon in a spouted-bed reactor as the second-stage reactor of a plastic recycling process

A two-stage process for the chemical recycling of plastics is proposed. In this process, which consists of two reactors, plastics are converted into hydrogen and carbon. In the first reactor, plastic chips are thermally decomposed into hydrocarbons. In the second reactor, the hydrocarbons formed in the first reactor are catalytically decomposed into carbon and hydrogen. In this study, in order to obtain basic data for the second reactor, propene was catalytically decomposed in a laboratory-scale spouted-bed reactor (600mm high, 21.6mm internal diameter, made of SUS304). The effect of the type of spouting medium used on the decomposition behavior of propene was investigated using four types of spouting medium (nickel-plated -alumina, palladium-plated -alumina, nickel-impregnated -alumina, and -alumina). The nickel-impregnated -alumina gave the best propene conversion and hydrogen yield.     

Novel Biobased Polyurethanes Synthesized from Soybean Phosphate Ester Polyols: Thermomechanical Properties Evaluations

Biobased polyurethanes from soybean oil–derived polyols and polymeric diphenylmethane diisocyanate (pMDI) are prepared and their thermomechanical properties are studied and evaluated. The cross-linked biobased polyurethanes being prepared from soy phosphate ester polyols with hydroxyl contents ranging from 122 to 145 mg KOH/g and pMDI within 5 min of reaction time at 150°C in absence of any catalyst show cross-linking densities ranging from 1.8 × 10³ to 3.0 × 10³ M/m³, whereas glass transition temperatures vary from approximately 69 to 82°C. The loss factor (tan ) curves show single peaks for all these biobased polyurethanes, thus indicating a single-phase system. The storage moduli (G) at 30°C range from 4 × 10⁸ to 1.3 × 10⁹ Pa. Upon postcure at 150°C, the thermomechanical properties can be optimized. Cross-link densities are improved significantly for hydroxyl content of 139 and 145 mg KOH/g at curing time of 24 h. Similarly, glass transition temperature (T_g) and storage moduli around and after T_g are increased. Meanwhile, tan intensities decrease as result of restricted chain mobility. Longer exposure time (24 h) induces thermal degradation, as evidenced by thermogravimetric analysis (TGA). The dynamic mechanical (DMA) analysis shows that postcure at 100°C for times exceeding 24 h also leads to improved properties. However, cross-linking densities are lower compared to postcure carried out at 150°C.     

Investigation of the Aerobic Biodegradability of Several Types of Cyclodextrins in a Laboratory-Controlled Composting Test

The biodegradation of several types of cyclodextrins (CDs) under laboratory-controlled composting conditions was investigated. CDs are used in a broad range of applications in food, pharmaceutical, medical, chemical, and textile industries because of their specific chemical characteristics related to their hydrophobic interior and hydrophilic exterior. The three naturally occurring cyclodextrins -CD, -CD, and -CD proved to be completely and readily biodegradable. Chemical modification of these basic compounds can have a major impact on the biodegradation rate and final biodegradation percentage. Fully acetylated -CD and -CD were found to be nonbiodegradable during 45 days of composting. Reducing the degree of acetylation had a positive effect on the biodegradation. Complete biodegradation was obtained for partially acetylated -CD with a degree of substitution (DS) of 7. The methylation (DS = 13) of -CD resulted in an undegradable compound during the 47 days composting, while (2-hydroxy)propyl--CD reached a plateau in biodegradation at a percentage of 20%. The incorporation of the antimicrobial agents imazalil and allyl-isothiocyanate into -CD had no negative impact on biodegradation, which makes these antimicrobial agents/CD complexes suitable for incorporation into biodegradable active packaging.