Breakthrough in 2D‐CSIA Technology for 1,4‐Dioxane

A dual isotope technology based on compound‐specific stable isotope analysis of carbon and hydrogen (2D‐CSIA) was recently developed to help identify sources and monitor in situ degradation of the contaminant 1,4‐dioxane (1,4‐D) in groundwater. Site investigation and optimized remediation have been the focus of thousands of CSIA applications completed for volatile organic contaminants (VOCs) worldwide. CSIA for the water miscible 1,4‐D, however, has been technically challenging. The most commercially available sample preparation settings “Purge and Trap” for VOC could not efficiently extract 1,4‐D out of water for a reliable CSIA measurement, especially when the concentration is below 100 μg/L. Such a high reporting limit has prevented CSIA from being used for effective site investigation and remediation monitoring at most 1,4‐D contaminated sites, where 1,4‐D is often present at very low ppb levels. This article outlines the recent breakthrough in 2D‐CSIA technology for 1,4‐D in water, reported down to ～1 μg/L for carbon, and ～10 μg/L to 20 μg/L for hydrogen using solid‐phase extraction based on EPA Method 522, and its benefit is highlighted through a case study at a 1,4‐D contaminated site. ©2016 Wiley Periodicals, Inc.     

Chlorinated Hydrocarbon–Contaminated Site Investigation With Optimized 3D‐CSIA Approach

An optimized “Three‐Dimensional Compound Specific Isotope Analysis (3D‐CSIA)'' investigation was conducted at a chlorinated hydrocarbon–contaminated site in order to (1) determine if multiple onsite sources of groundwater contamination existed and (2) demonstrate the cost‐effectiveness of applying isotope fingerprinting at such a complex contaminated site. Previous groundwater investigations identified chlorinated hydrocarbons at levels that significantly exceed drinking‐water standards but failed to determine the source(s) of contamination due to the lack of vadose‐zone contamination and the absence of groundwater contaminants in shallow portions of the surficial aquifer. To better understand the contaminant source(s), groundwater samples were taken and tested for both the presence of chlorinated hydrocarbons and their isotopic signatures of ¹³C/¹²C, ³⁷Cl/³⁵Cl, and ²H/¹H. A site investigation with an optimized 3D‐CSIA approach revealed multiple chlorinated hydrocarbon releases from different sources, which was also cost‐effective considering the new lines of evidence of target contaminants obtained with the 3D‐CSIA approach instead of any traditional fingerprinting approaches. In addition, the 3D‐CSIA results inferred in situ bioremediation of chlorinated hydrocarbons would be feasible at the site. © 2013 Wiley Periodicals, Inc.     

CSIA of TCE and Daughter Products With Multiple Sources,Multiple Attenuation Mechanisms,and Low Ethene

One of the most often asked questions from regulators considering monitored natural attenuation (MNA) for a site is if there are mechanisms in situ that can completely detoxify the contaminant of concern. This article describes a method that uses data derived from compound‐specific isotope analysis (CSIA) to investigate if complete in situ degradation of trichloroethene (TCE) has occurred. MNA was the selected remediation strategy at the former England Air Force Base (fEAFB) in Louisiana. Previously declining concentrations of TCE, 1,2‐cis‐dichloroethene, and vinyl chloride had increased in selected wells, and less ethene was observed than expected on the basis of mass balance. Reductive dechlorination, partial or otherwise, could not explain observed trends, so the question at fEAFB had become: Was there an in situ mechanism for complete TCE detoxification (i.e., complete degradation to innocuous end products) at the site? CSIA was used for investigating this question at fEAFB. A previously developed formalism was adapted to interpret the CSIA data to answer the question. Standard interpretation assuming only reductive dechlorination demonstrated detoxification in 9 of the 15 contaminated wells, whereas the interpretation developed here did so in 14. © 2014 Wiley Periodicals, Inc.     

Evolution of predictive tools for in situ bioremediation and natural attenuation evaluations

Proving the viability of in situ bioremediation technologies and gathering data for its full‐scale implementation typically involves collecting multiple rounds of data and often completing microcosm studies. Collecting these data is cumbersome, time‐consuming, costly, and typically difficult to scale. A new method of completing microcosm studies in situ using an amendable sampling device deployed and incubated in groundwater monitoring wells provides actionable data to expedite site cleanup. The device, referred to as a Bio‐Trap® sampler, is designed to collect actively colonizing microbes and dissolved organic compounds from groundwater for analysis using conventional analytical techniques and advanced diagnostic tools that can answer very specific design and viability questions relating to bioremediation. Key data that can be provided by in situ microcosm studies using Bio‐Trap® samplers include definitively demonstrating contaminant destruction by using compound‐specific isotope analysis and providing data on the mechanism of the degradation by identifying the responsible microbes. Three case studies are presented that demonstrate the combined flexibility of Bio‐Trap® samplers and advanced site diagnostics. The applications include demonstrating natural attenuation of dissolved chlorinated solvents, demonstrating natural attenuation of dissolved petroleum compounds, and using multiple Bio‐Trap® samplers to comparatively assess the viability of bioaugmentation at a chlorinated solvent release site. At each of these sites, the in situ microcosm studies quickly and cost‐effectively answered key design and viability questions, allowing for regulatory approval and successful full‐scale implementation. © 2010 Wiley Periodicals, Inc.     

Injecting remediation compounds—How you inject is equally as important as what you inject

The injection of remediation compounds has rapidly become a widely accepted approach for addressing contaminated sites. One of the most fundamental questions surrounding the use of in situ remediation has been “What compound are you injecting at your site?” With the advances in the industry's understanding and acceptance of the in situ remediation process remediation professionals are now asking a follow‐up question that has become equally important to the success of a project: “How are you injecting a compound at your site?” This article discusses advances in field applications for in situ remediation and injecting remediation compounds. © 2003 Wiley Periodicals, Inc.     

Application of the operating window concept to remediation‐option selection

An Erratum has been published for this article in Remediation 14(4) 2004, 141. The selection of remediation options for the management of unacceptable risks at contaminated sites is hindered by insufficient information on their performance under different site conditions. Therefore, there is a need to define “operating windows” for individual remediation options to summarize their performance under a variety of site conditions. The concept of the “operating window” has been applied as both a performance optimization tool and decision support tool in a number of different industries. Remediation‐option operating windows could be used as decision support tools during the “options appraisal” stage of the Model Procedures (CLR 11), proposed by the Environment Agency (EA) for England and Wales, to enhance the identification of “feasible remediation options” for “relevant pollutant linkages.” The development of remediation‐option operating windows involves: 1) the determination of relationships between site conditions (“critical variables”) and option performance parameters (e.g., contaminant degradation or removal rates) and 2) the identification of upper‐ and lower‐limit values (“operational limits”) for these variables that define the ranges of site conditions over which option performance is likely to be sufficient (the “operating window”) and insufficient (the “operating wall”) for managing risk. Some research has used case study data to determine relationships between critical variables and subsurface natural attenuation (NA) process rates. Despite the various challenges associated with the approach, these studies suggest that available case study data can be used to develop operating windows for monitored natural attenuation (MNA) and, indeed, other remediation options. It is envisaged that the development of remediation‐option operating windows will encourage the application of more innovative remediation options as opposed to excavation and disposal to landfill and/or on‐site containment, which remain the most commonly employed options in many countries. © 2004 Wiley Periodicals, Inc.     

Sustained treatment: Implications for treatment timescales associated with source‐depletion technologies

Sustained treatment is an emerging concept used to describe enhancements in attenuation capacity after the conclusion of the active treatment period for a given source‐depletion technology. The term includes mechanisms that lead to contaminant transformation or destruction over extended periods of time, such as endogenous biomass decay, slow diffusion of remedial amendments from low‐permeability zones, and the formation of reactive mineral species. This “value‐added” treatment continues after the end of capital expenditures at a site, and it provides additional insight in determining if monitored natural attenuation is a viable long‐term option for a site. This article identifies several sustained treatment mechanisms, examines technology‐specific factors that contribute to sustained treatment, and explores the potential timescales of sustained treatment relative to active treatment. As demonstrated in post‐treatment site data obtained during a comprehensive source‐depletion technology performance survey, enhanced bioremediation is the most promising in promoting sustained treatment, and this beneficial effect can extend for several years due to factors such as slow biomass decay. There is little evidence that other commonly used technologies (thermal treatment, in situ chemical oxidation, surfactant‐enhanced remediation, or cosolvent flushing) result in any significant sustained treatment. An exception would be a cosolvent flushing project where large quantities of biodegradable cosolvent are left in the subsurface at the end of the project, which could result in sustained long‐term dechlorination activity. In the case of in situ chemical oxidation, factors that contribute to a higher incidence of concentration rebound mask any potential sustained treatment effects. © 2011 Wiley Periodicals, Inc.     

1,4‐Dioxane Treatment Technologies

The chlorinated solvent stabilizer 1,4‐dioxane (DX) has become an unexpected and recalcitrant groundwater contaminant at many sites across the United States. Chemical characteristics of DX, such as miscibility and low sorption potential, enable it to migrate at least as far as the chlorinated solvent from which it often originates. This mobility and recalcitrance has challenged remediation professionals to redesign existing treatment systems and monitoring networks to accommodate widespread contamination. Furthermore, remediation technologies commonly applied to chlorinated solvent co‐contaminants, such as extraction and air stripping or in situ enhanced reductive dechlorination, are relatively ineffective on DX removal. These difficulties in treatment have required the industry to identify, develop, and demonstrate new and innovative technologies and approaches for both ex situ and in situ treatment of this emerging contaminant. Great strides have been made over the past decade in the development and testing of remediation technologies for removal or destruction of DX in groundwater. This article briefly summarizes the fate and transport characteristics of DX that make it difficult to treat, and presents technologies that have been demonstrated to be applicable to groundwater treatment at the field scale.  ©2016 Wiley Periodicals, Inc.     

In-situ bioremediation of hanford groundwater

The U.S. Department of Energy has generated liquid wastes containing radioactive and hazardous chemicals throughout the more than forty years of operation at its Hanford site in Washington State. Many of the waste components, including nitrate and carbon tetrachloride (CCl₄), have been detected in the Hanford groundwater. In-situ bioremediation of CCl₄ and nitrate is being considered to clean the aquifer. Preliminary estimates indicate that this technology should cost significantly less than ex-situ bioremediation and about the same as air stripping/granular activated carbon. In-situ bioremediation has the advantage of providing ultimate destruction of the contaminant and requires significantly less remediation time. Currently, a test site is under development. A computer-aided design tool is being used to design optimal remediation conditions by linking subsurface transport predictions, site characterization data, and microbial growth and contaminant destruction kinetics.     

New perspectives in the use of horizontal wells for assessment and remediation

Remediation technologies can sometimes be established, but are not prevalent, for a variety of reasons; however, they can be subject to the forces of change. In some cases, creative economics promotes new uses, but also process improvements can drive new applications and levels of acceptance. This is what is happening with the deployment of horizontal wells for site assessment and remediation. In essence, decreasing costs and a strategic shift, which can be characterized as “greater flexibility,” are two factors that have brought about a resurgence of horizontal well systems. The latter is specifically tied to moving from monolithic single well systems to segmented well systems and this article explains how this is a next‐generation advancement in site assessment and remediation. As one example, nested, discrete horizontal profiling brings additional accuracy to assessment at sites, especially those challenged by access issues and also provides more directed treatment operations with a unique flexibility in dynamic groundwater systems. Also, with horizontal nested well systems, conceptual site models can be significantly enhanced with new perspectives and, depending on the situation, may provide significant economic advantages in deployment. Finally, this technological advancement creates a new paradigm in contrast, or rather as an adjunct, to vertical profiling and high‐resolution site characterization. In fact, it opens up a new strategic approach that can be called high‐resolution contaminant distribution, because flexible horizontal segmented well systems can be used to navigate “up the spine of the plume” providing discretized data sets that illuminate contaminant distribution in new ways.     

Iron‐mediated abiotic degradation of RDX in a contaminated aquifer

The influence of aqueous‐ and mineral‐phase iron on royal demolition explosive (RDX) destruction has been previously investigated in theoretical settings and bench‐scale tests by various practitioners. The feasible use of in situ redox manipulation to create reactive Fe(II) is contingent upon the aquifer containing enough iron oxides and iron‐bearing clay minerals for the treated zone to remain effective. The following is a summary of a bench‐scale assessment of this relationship using aquifer material from an ongoing groundwater remediation effort at the Iowa Army Ammunition Plant (IAAP). A bench‐scale study was designed to determine the relative contributions of the biotic and iron‐mediated abiotic degradation processes to the net decrease in RDX observed at the site using saturated aquifer samples collected from within the RDX plume. Sterilized samples with a sufficient stoichiometric excess of both soluble and mineral‐phase iron reduced concentrations of RDX in both the soil and water fractions to the same extent as the samples containing native biota. These results indicate that in situ, abiotic degradation of RDX is feasible in areas unsuitable to biotic degradation processes, yielding an additional alternative for in situ RDX remediation. © 2012 Wiley Periodicals, Inc.     

Closing the mass balance at chlorinated solvent sites: Sources and attenuation processes

Using detailed mass balance and simple analytical models, a spreadsheet‐based application (BioBalance) was developed to equip decision makers with a predictive tool that can provide a semiquantitative projection of source‐zone concentrations and provide insight into the long‐term behavior of the associated chlorinated solvent plume. The various models were linked in a toolkit in order to predict the composite impacts of alternative source‐zone remediation technologies and downgradient attenuation processes. Key outputs of BioBalance include estimates of maximum plume size, the time frame for plume stabilization, and an assessment of the sustainability of anaerobic natural attenuation processes. The toolkit also provides spatial and temporal projections of integrated contaminant flux and plume centerline concentrations. Results from model runs of the toolkit indicate that, for sites trying to meet traditional, “final” remedial objectives (e.g., two to three orders of magnitude reduction in concentration with restoration to potable limits), “dispersive” mechanisms (e.g., heterogeneous flow and matrix diffusion) can extend remedial time frames and limit the benefits of source remediation in reducing plume sizes. In these cases, the removal of source mass does not result in a corresponding reduction in the time frame for source remediation or plume stabilization. However, this should not discourage practitioners from implementing source‐depletion technologies, since results from the toolkit demonstrate a variety of measurable benefits of source remediation. Model runs suggest that alternative, “intermediate” performance metrics can improve and clarify source remediation objectives and better monitor and evaluate effectiveness. Suggested intermediate performance metrics include reduction in overall concentrations or mass within the plume, reduction of flux moving within a plume, and reduction in the potential for risk to a receptor or migration of a target concentration of contaminant beyond a site boundary. This article describes the development of two key modules of the toolkit as well as illustrates the value of using intermediate performance metrics to evaluate the performance of a source‐remediation technology. © 2010 Wiley Periodicals, Inc.     

Quantitative Environmental Footprints and Sustainability Evaluation of Contaminated Land Remediation Alternatives for Two Case Studies

Since the US Environmental Protection Agency (US EPA) launched its “green remediation” program and EU member states began to reassess their national regulations for environmental remediation in order to reach a Europe‐wide consensus on policy and standards, the need and interest for sustainable remediation of contaminants from brownfields has grown considerably. Concomitantly, the ability to calculate and assess the suitability as well as the environmental footprints and associated risks of a growing number of remediation techniques has become a priority. The authors quantitatively evaluate the differences between various remediation techniques, and for this purpose, a number of ex situ and in situ remediation techniques are adapted to model 21 remediation scenarios for two contaminated sites in the Gothenburg region of Sweden: the Bohus Varv site on the Göta älv river bank and the Hexion site in Mölndal. A wide range of quantitative results for these models are presented, compared, and analyzed. Based on the results from both projects, it is concluded that: (1) remediation techniques requiring long distance residual transportation have significant footprints, except the transportation of contaminated residuals by train due to Swedish energy production conditions; (2) residual transportation by ship results in much higher SO_x, NO_x, and particle releases compared to the other alternatives; and (3) residual transporation by truck results in high accident risks. Finally, activities powered by electricity result in a reduced footprint compared to activities powered by fossil fuels, considering Swedish energy production conditions. The authors conducted a cross‐benefit analysis of SiteWise^TM applications which recognizes its potential as a tool for presenting life cycle assessment analyses with appropriate system boundary definitions and an easy inventory analysis process. Results from this tool provide valuable support to decision makers aiming at more sustainable remediation. © 2013 Wiley Periodicals, Inc.     

Life‐cycle assessment of in situ thermal remediation

A detailed cradle‐to‐grave life‐cycle assessment (LCA) of an in situ thermal treatment remedy for a chlorinated‐solvent‐contaminated site was performed using process LCA. The major materials and activities necessary to install, operate, monitor, and deconstruct the remedy were included in the analysis. The analysis was based on an actual site remedy design and implementation to determine the potential environmental impacts, pinpoint major contributors to impacts, and identify opportunities for improvements during future implementation. The Electro‐Thermal Dynamic Stripping Process (ET‐DSP?) in situ thermal technology coupled with a dual‐phase extraction and treatment system was evaluated for the remediation of 4,400 yd³ of tetrachloroethene‐ and trichloroethene‐impacted soil, groundwater, and bedrock. The analysis was based on an actual site with an estimated source mass of 2,200 lbs of chlorinated solvents. The remedy was separated into four stages: remedy installation, remedy operation, monitoring, and remedy deconstruction. Environmental impacts were assessed using Sima Pro software, the ecoinvent database, and the ReCiPe midpoint and endpoint methods. The operation stage of the remedy dominated the environmental impacts across all categories due to the large amount of electricity required by the thermal treatment technology. Alternate sources of electricity could significantly reduce the environmental impacts of the remedy across all impact categories. Other large impacts were observed in the installation stage resulting from the large amount of diesel fuel, steel, activated carbon, and asphalt materials required to implement the technology. These impacts suggest where opportunities for footprint reductions can be found through best management practices such as increased materials reuse, increased recycled‐content materials use, and clean fuels and emission control technologies. Smaller impacts were observed in the monitoring and deconstruction stages. Normalized results show the largest environmental burdens to fossil depletion, human toxicity, particulate matter formation, and climate‐change categories resulting from activities associated with mining of fossil fuels for use in electricity production. In situ thermal treatment can reliably remediate contaminated source areas with contaminants located in low‐permeability zones, providing complete destruction of contaminants in a short amount of time, quick return of the site to productive use, and minimized quantities of hazardous materials stored in landfills for future generations to remediate. However, this remediation strategy can also result in significant emissions over a short period of time. It is difficult to quantify the overall value of short‐term cleanups with intense treatment emissions against longer‐term cleanups with lower treatment emissions because of the environmental, social, and economic trade‐offs that need to be considered and understood. LCA is a robust, quantitative tool to help inform stakeholder discussions related to the remedy selection process, trade‐off considerations, and environmental footprint‐reduction opportunities, and to complement a broader toolbox for the evaluation of sustainable remediation strategies. © 2012 Wiley Periodicals, Inc.     

Chloroethene dechlorination in acidic groundwater: Implications for combining fenton's treatment with natural attenuation

A sulfuric acid leak in 1988 at a chloroethene‐contaminated groundwater site at the Naval Air Station Pensacola has resulted in a long‐term record of the behavior of chloroethene contaminants at low pH and a unique opportunity to assess the potential impact of source area treatment technologies, which involve acidification of the groundwater environment (e.g., Fenton's‐based in situ chemical oxidation), on downgradient natural attenuation processes. The greater than 75 percent decrease in trichloroethene (TCE) concentrations and the shift in contaminant composition toward predominantly reduced daughter products (dichloroethene [DCE] and vinyl chloride [VC]) that were observed along a 30‐m groundwater flow path characterized by highly acidic conditions (pH = 3.5 ± 0.4) demonstrated that chloroethene reductive dechlorination can continue to be efficient under persistent acidic conditions. The detection of Dehalococcoides‐type bacteria within the sulfuric acid/chloroethene co‐contaminant plume was consistent with biotic chloroethene reductive dechlorination. Microcosm studies conducted with ¹⁴C‐TCE and ¹⁴C‐VC confirmed biotic reductive dechlorination in sediment collected from within the sulfuric acid/chloroethene co‐contaminant plume. Microcosms prepared with sediment from two other locations within the acid plume, however, demonstrated only a limited mineralization to ¹⁴CO₂ and ¹⁴CO, which was attributed to abiotic degradation because no significant differences were observed between experimental and autoclaved control treatments. These results indicated that biotic and abiotic mechanisms contributed to chloroethene attenuation in the acid plume at NAS Pensacola and that remediation techniques involving acidification of the groundwater environment (e.g., Fenton's‐based source area treatment) do not necessarily preclude efficient chloroethene degradation. © 2007 Wiley Periodicals, Inc.     

Incorporating Bioavailability Considerations Into the Evaluation of Contaminated Sediment Sites

In March 2011, the Interstate Technology & Regulatory Council (ITRC) Contaminated Sediments Team published a web‐based Technical and Regulatory Guidance on the concepts, processes, and uses of bioavailability in a risk decision‐making framework at a contaminated sediment site. Bioavailability processes, as defined by the National Research Council (NRC; 2003), are the “individual physical, chemical, and biological interactions that determine the exposure of plants and animals to chemicals associated with soils and sediments.” Bioavailability assessment tools aid in the assessment of human and ecological exposure and development of site‐specific remedial objectives. The guidance provides information on the processes that may affect contaminant bioavailability within sediments to understand exposure within ecological and human receptors; supports the development of conceptual site models (CSMs); and describes available tools (biological, chemical, and physical) and models that are used to measure and characterize the fate and transport and potential bioavailability of contaminants. Case studies, referenced throughout the document, demonstrate the practical application of bioavailability measures. The guidance will describe the proper application of traditional and emerging sediment remediation technologies to support the selection of a remedy that is protective of human health and the environment. © 2013 Wiley Periodicals, Inc.     

Groundwater geochemistry diagnostics during in situ ERH remediation

In situ remediation represents a series of challenges in interpreting the monitoring data on remedial progress. Among these challenges are problems in determining the progress of the remediation and the mechanisms responsible, so that the process can be optimized. The release of organic pollutants to groundwater systems and in situ remediation technologies alter the groundwater chemistry, but outside of natural attenuation studies using inorganic chemical analyses as indicators of intrinsic biodegradation, typically little attention has been paid to the changes in inorganic groundwater chemistry. Smith (2008) noted that during an electrical resistance heating remediation that took place at a confidential site in Chicago, a two‐orders‐of‐magnitude increase in chloride concentrations occurred during the remediation. This increase in chloride resulted in a corresponding increase in calcium as a result of what is known as the common ion effect. Carbon dioxide is the gas found in highest concentrations in natural groundwater (Stumm & Morgan, 1981), and its fugacity (partial pressure) corresponds directly with calcium concentrations. Carbon dioxide at supersaturation in groundwater is capable of dissolving organic compounds, such as trichloroethene, facilitating removal of nonaqueous‐phase liquids at temperatures below the boiling point of water. One means of diagnosing these reactions is through the use of compound‐specific isotopic analysis, which is capable of distinguishing between evaporation, biodegradation, and differences in sources. The appropriate diagnosis has the potential to optimize the benefits from these reactions, lower energy costs for removal of nonaqueous‐phase liquids, and direct treatment where it is needed most. © 2010 Wiley Periodicals, Inc.     

In situ thermal remediation of DNAPL and LNAPL using electrical resistance heating

Electrical resistance heating (ERH) is an in situ treatment for soil and groundwater remediation that can reduce the time to clean up volatile organic compounds (VOCs) from years to months. The technology is now mature enough to provide site owners with both performance and financial certainty in their site‐closure process. The ability of the technology to remediate soil and groundwater impacted by chlorinated solvents and petroleum hydrocarbons regardless of lithology proves to be beneficial over conventional in situ technologies that are dependent on advective flow. These conventional technologies include: soil vapor recovery, air sparging, and pumpand‐treat, or the delivery of fluids to the subsurface such as chemical oxidization and bioremediation. The technology is very tolerant of subsurface heterogeneities and actually performs as well in low‐permeability silts and clay as in higher‐ permeability sands and gravels. ERH is often implemented around and under buildings and public access areas without upsetting normal business operations. ERH may also be combined with other treatment technologies to optimize and enhance their performance. This article describes how the technology was developed, how it works, and provides two case studies where ERH was used to remediate complex lithologies. © 2005 Wiley Periodicals, Inc.     

Detecting and quantifying reductive dechlorination under monitored natural attenuation conditions

Field sampling and testing were used to investigate the relationship between baseline geochemical and microbial community data and in situ reductive dechlorination rates at a site contaminated with trichloroethene (TCE) and carbon tetrachloride (CTET). Ten monitoring wells were selected to represent conditions along groundwater flow paths from the contaminant source zone to a wetlands groundwater discharge zone. Groundwater samples were analyzed for a suite of geochemical and microbial parameters; then push‐pull tests with fluorinated reactive tracers were conducted in each well to measure in situ reductive dechlorination rates. No exogenous electron donors were added in these tests, as the goal was to assess in situ reductive dechlorination rates under natural attenuation conditions. Geochemical data provided preliminary evidence that reductive dechlorination of TCE and CTET was occurring at the site, and microbial data confirmed the presence of known dechlorinating organisms in groundwater. Push‐pull tests were conducted using trichlorofluoroethene (TCFE) as a reactive tracer for TCE and, in one well, trichlorofluoromethane (TCFM) as a reactive tracer for CTET. Injected TCFE was transformed to cis‐ and trans‐dichlorofluoroethene and chlorofluoroethene, and, in one test, injected TCFE was completely dechlorinated to fluoroethene (FE). In situ TCFE transformation rates ranged from less than 0.005 to 0.004/day. In the single well tested, injected TCFM was transformed in situ to dichlorofluoromethane and chlorofluoromethane; the TCFM transformation rate was estimated as 0.001/day. The results indicate that it is possible to use push‐pull tests with reactive tracers to directly detect and quantify reductive dechlorination of chlorinated ethenes and ethanes under monitored natural attenuation conditions, which has not previously been demonstrated. Transformation rate estimates obtained with these techniques should improve the accuracy of contaminant transport modeling. © 2012 Wiley Periodicals, Inc.     

Synthetic Media: A Promising New Treatment Technology for 1,4‐Dioxane

1,4‐Dioxane (14DX) is classified as a probable human carcinogen by the US Environmental Protection Agency (EPA), and it has toxic effects on the kidney and liver. EPA's Health Advisory Level (HAL) for 14DX is 0.35 micrograms per liter (μg/L). Accordingly, several states have lowered their drinking water advisory levels and site cleanup levels. The widespread occurrence of 14DX in contaminated groundwater has contributed to a growing demand for remediation services. Treating 14DX is a challenge due to its very low Henry's law constant, low sorption potential, and strong ether linkages. The primary solution for 14DX remediation has been various forms of advanced oxidation processes (AOP), namely pump and treat followed by ex situ treatment with catalyzed ultraviolet light oxidation or ozone‐peroxidation. Many of the available advanced oxidation systems are complex, requiring careful monitoring and maintenance to adjust for variable source water and operating conditions. Synthetic media is a relatively new 14DX treatment technology that overcomes many of the operating challenges faced by existing technologies. AMBERSORB? 560 (AMBERSORB) has recently demonstrated the effective removal of 14DX over a wide range of concentrations and operating conditions, including those created by in situ thermal remediation. Consistent and reliable treatment down to sub‐0.3 μg/L levels differentiates synthetic media technology from other 14DX treatment technologies. AMBERSORB provides a solution to the problem of “stranded capital” by offering a 14DX treatment system capable of meeting regulatory standards today and in the foreseeable future. © 2014 Wiley Periodicals, Inc.