Physicochemical characterization of hydroxyapatite and its application towards removal of nitrate from water

A laboratory study was conducted to investigate the efficiency of hydroxyapatite (HAP) towards removal of nitrate from synthetic nitrate solution. In the present research HAP synthesized from egg-shell was characterized using SEM, XRD, FTIR and TGA–DSC. The removal of nitrate was 96% under neutral conditions, using 0.3 g of adsorbent in 100 mL of nitrate solution having an initial concentration of 100 mg/L. An adsorption kinetic study revealed that the adsorption process followed first order kinetics. Adsorption data were fitted to a linearly transformed Langmuir isotherm with correlation coefficient (R²) > 0.98. Thermodynamic parameters were also calculated to study the effect of temperature on the removal process. In order to understand the adsorption type, equilibrium data were tested with the Dubinin–Radushkevich isotherm. The process was rapid and equilibrium was established within the first 40 min.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Application of carbon adsorbents prepared from Brazilian-pine fruit shell for the removal of reactive orange 16 from aqueous solution: Kinetic,equilibrium, and thermodynamic studies

Activated (AC-PW) and non-activated (C-PW) carbonaceous materials were prepared from the Brazilian-pine fruit shell (Araucaria angustifolia) and tested as adsorbents for the removal of reactive orange 16 dye (RO-16) from aqueous effluents. The effects of shaking time, adsorbent dosage and pH on the adsorption capacity were studied. RO-16 uptake was favorable at pH values ranging from 2.0 to 3.0 and from 2.0 to 7.0 for C-PW and AC-PW, respectively. The contact time required to obtain the equilibrium using C-PW and AC-PW as adsorbents was 5 and 4 h at 298 K, respectively. The fractionary-order kinetic model provided the best fit to experimental data compared with other models. Equilibrium data were better fit to the Sips isotherm model using C-PW and AC-PW as adsorbents. The enthalpy and entropy of adsorption of RO-16 were obtained from adsorption experiments ranging from 298 to 323 K.     

Equilibrium studies of copper ion adsorption onto palm kernel fibre

The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin–Radushkevich (D–R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r², and the non-linear Chi-square, χ² error analysis.The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH_PZC of the palm kernel fibre with an optimum dose of 10 g/dm³. The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 × 10^?4 mol/g at 339 K. The sorption equilibrium constant, K_a, increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B₁, with increasing temperature. The Dubinin–Radushkevich (D–R) isotherm parameter, free energy, E, was in the range of 15.7–16.7 kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO₃ and CH₃COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic.     

Phenol removal from aqueous environments by natural & chemically modified kaolin clay

Natural, acid and base modified kaolin clays were studied for the sake of phenol and 4-chlorophenol removal from aqueous environments and their application to real ground and industrial wastewater samples. Scanning electron microscope (SEM), infrared spectroscopy (IR), X-ray diffraction (XRD), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA), and Surface area analysis were employed for characterization of the adsorbents microstructure. Operating factors such as adsorbent dose, solution pH, initial phenol concentration, and contact time were studied. The experimental data displayed that the increase of the adsorbent dose, contact time, and pH value from 2 to 7 increases the efficiency of the removal process. Optimal conditions for phenolic removal were; contact time of 300 min, primary phenol solution of 25 mg/L, pH 7 and 2.5 g/L as an appropriate adsorbent dose using crude (natural), acid modified and base modified kaolin clays. The higher phenolic removal efficiencies were obtained at 5 mg/L as 90, 97, 96.2%, respectively, for the adsorbents in the previously mentioned order. The adsorption capacity in the removal of phenol and 4-chlorophenol were 7.481 and 4.195, 8.2942 and 3.211, and 8.05185 and 18.565 mg/g, respectively, for the adsorbents in the same mentioned order. The adsorption equilibrium data were fitted and analyzed with four isotherm models, namely, Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm equations. The adsorption process of phenol on studied adsorbents was exothermic, spontaneous and thermodynamically favorable proved by the negative values of their thermodynamic parameters ΔH° and ΔG°. The correlation coefficient (R²) for all concentrations was higher than 0.94, which indicates that in the studied system, the data suitably fit the first-order kinetics. The % desorption capacity was amounted to 96%, 91.11%, and 87.06% of adsorbed phenol, respectively, for the adsorbents in the previous order using 0.1N NaOH and 10% V/V ethanol solutions as eluents at 25°C, indicating the reusability of the adsorbents. Kaolin and its modified forms can be introduced as eco-friendly and low-cost adsorbents in water remediation implementation.     

Effect of salinity on metal-complex dye biosorption by Rhizopus arrhizus

In this study the biosorption of Yellow RL, a metal-complex anionic dye, by dried Rhizopus arrhizus, a filamentous fungus, was investigated as a function of initial solution pH, initial dye concentration and initial salt (sodium chloride) concentration. The fungus exhibited the maximal dye uptake at pH 2 in the absence and in the presence of salt. Dye uptake increased with the dye concentration up to 1000 mg l^?1 and diminished considerably in the presence of increasing concentrations of salt up to 50 g l^?1. The fungus biosorbed 85.4 mg dye g^?1of dried biomass at 100 mg l^?1 initial dye concentration in the absence of salt. When 50 g l^?1 salt was added to the biosorption medium, this value dropped to 60.8 mg g^?1 resulting in 28.8% reduction in biosorption capacity. The Redlich–Peterson and Langmuir–Freundlich were the most suitable adsorption models for describing the biosorption equilibrium data of the dye both individually and in salt containing medium. The pseudo-second-order and saturation type kinetic models depicted the biosorption kinetics accurately for all cases studied. Equilibrium and kinetic constants varied with the level of salt were expressed as a function of salt concentration.     

Treatment and toxicity evaluation of methylene blue using electrochemical oxidation,fly ash adsorption and combined electrochemical oxidation-fly ash adsorption

Treatment of a basic dye, methylene blue, by electrochemical oxidation, fly ash adsorption, and combined electrochemical oxidation-fly ash adsorption was compared. Methylene blue at 100 mg L^?1 was used in this study. The toxicity was also monitored by the Vibrio fischeri light inhibition test.When electrochemical oxidation was used, 99% color and 84% COD were removed from the methylene blue solution in 20 min at a current density of 428 A m^?2, NaCl of 1000 mg L^?1, and pH₀ of 7. However, the decolorized solution showed high toxicity (100% light inhibition).For fly ash adsorption, a high dose of fly ash (>20,000 mg L^?1) was needed to remove methylene blue, and the Freundlich isotherm described the adsorption behavior well.In the combined electrochemical oxidation-fly ash adsorption treatment, the addition of 4000 mg L^?1 fly ash effectively reduced intermediate toxicity and decreased the COD of the electrochemical oxidation-treated methylene blue solution. The results indicated that the combined process effectively removed color, COD, and intermediate toxicity of the methylene blue solution.     

Removal of chromium (VI) from aqueous solution using walnut hull

In this study, removal of chromium (VI) from aqueous solution by walnut hull (a local low-cost adsorbent) was studied. The extent of adsorption was investigated as a function of solution pH, contact time, adsorbent and adsorbate concentration, reaction temperature and supporting electrolyte (sodium chloride). The Cr (VI) removal was pH-dependent, reaching a maximum (97.3%) at pH 1.0. The kinetic experimental data were fitted to the first-order, modified Freundlich, intraparticle diffusion and Elovich models and the corresponding parameters were obtained. A 102.78 kJ/mol Ea (activation energy) for the reaction of chromium (VI) adsorption onto walnut indicated that the rate-limiting step in this case might be a chemically controlled process. Both the Langmuir and Freundlich isotherms were suitable for describing the biosorption of chromium (VI) onto walnut hull. The uptake of chromium (VI) per weight of adsorbent increased with increasing initial chromium (VI) concentration up to 240-480 mg/L, and decreased sharply with increasing adsorbent concentration ranging from 1.0 to 5.0 g/L. An increase in sodium chloride (as supporting electrolyte) concentration was found to induce a negative effect while an increase in temperature was found to give rise to a positive effect on the chromium (VI) adsorption process. Compared to the various other adsorbents reported in the literature, the walnut hull in this study shows very good promise for practical applicability.     

Environmental resource footprinting of drug manufacturing: Effects of scale-up and tablet dosage

The formulation and scale-up of batch processes is one of the major challenges in the development of pharmaceutical dosage forms and at the same time a significant resource demanding process which is generally overlooked in environmental sustainability assessments. First, this paper proposes general trends in the experience curve of cumulative resource consumption of pharmaceutical tablet manufacturing of PREZISTA^® 800 mg through wet granulation (WG) at four consecutive scales in both R&D and manufacturing environments (resp. WG1 = 1 kg/h, WG5 = 5 kg/h, WG30 = 30 kg/h and WG240 = 240 kg/h). Second, the authors aim at evaluating the environmental impact from a life cycle perspective of a daily consumption of PREZISTA^® 2× 400 mg tablets versus the bioequivalent PREZISTA^® 800 mg tablet which was launched to enhance patient compliance. Environmental sustainability assessment was conducted at three different system boundaries, which enables identification, localization and eventually reduction of burdens, in this case natural resource extraction. Exergy Analysis (EA) was used at process level (α) and plant level (β) while a cradle-to-gate Exergetic Life Cycle Assessment (ELCA) was conducted at the overall industrial level (γ) by means of the CEENE method (Cumulative Exergy Extraction from the Natural Environment). Life cycle stages taken into account are Active Pharmaceutical Ingredient (API) production, Drug Product (DP) production and Packaging. At process level (α), the total resource extraction for the manufacturing of one daily dose of PREZISTA^® (800 mg tablet) amounted up to 0.44 MJ_ex at the smallest scale (WG1) while this amount proved to be reduced by 58%, 79% and 83% at WG5, WG30 and WG240 respectively. Expanding the boundaries to the overall industrial level (γ) reveals that the main resource demand is at the production of the Active Pharmaceutical Ingredient (API), excipients, packaging materials and cleaning media used in DP production. At the largest scale (WG240) the use of cleaning media during DP production contributes considerably less to the total resource extraction. Overall, the effect of scale-up and learning on resource consumption during DP production showed to possess a power-law experience curve y = 2.40 * x^−0.57 when shifting from WG1 (smallest lab scale) to WG240 (industrial manufacturing). Tablet dosage (2× 400 mg versus 1× 800 mg) did not significantly affect the absolute environmental burden. However, the relative contribution of resource categories did change due to the different production technology. It could be concluded that in meeting social and economic demands by launching the PREZISTA^® 800 mg tablet, no trade-off in environmental burden occurred. On the long term, future research should strive to take into account R&D processes and all services related to pipeline activities taking place prior to market launch and eventually to allocate impacts to the final product.     

Airborne manganese concentrations on the Korean peninsula from 1991 to 2006

In this study, the distribution of airborne manganese (Mn) bound with particulate matters (PM) was investigated using data sets collected from 15 major cities in Korea over a 16-year time span (1991–2006). The mean Mn concentration measured from all the major cities in Korea throughout the entire study period was 71 ng m^?3, while the annual mean values of different cities ranged from 10.5 ng m^?3 in Yeosu (2003) to 615 ng m^?3 in Wonju (2006). The Mn levels were considerably larger in industrialized areas than in other land-use types. The Mn concentrations in the major industrial cities of Pohang, Incheon, and Ansan averaged 255, 98.2, and 84.6 ng m^?3, respectively; these values were far higher than those measured typically at most cities, e.g., 20–60 ng m^?3. Seasonal patterns characterized by the peak occurrence in spring and the noticeable drop in summer reflected the effects of the massive PM inflow from China (spring) and effective washout by summer monsoon in East Asia, respectively. Examination of Mn data over a long-term period indicated that the temporal trends of Mn seen in most cities were fairly constant through time since the 1990s, although some abnormalities were observed in cities of strong man-made activities (e.g., Pohang and Wonju). In light of the severity of airborne Mn pollution in many urban areas, it is desirable to establish an abatement strategy that can help effectively reduce Mn levels.     

Optimization of Fenton oxidation pre-treatment for B. thuringiensis – Based production of value added products from wastewater sludge

Fenton oxidation pretreatment was investigated for enhancement of biodegradability of wastewater sludge (WWS) which was subsequently used as substrate for the production of value- added products. The Response surface method with fractional factorial and central composite designs was applied to determine the effects of Fenton parameters on solubilization and biodegradability of sludge and the optimization of the Fenton process. Maximum solubilization and biodegradability were obtained as 70% and 74%, respectively at the optimal conditions: 0.01 ml H₂O₂/g SS, 150 [H₂O₂]₀/[Fe²⁺]₀, 25 g/L TS, at 25 °C and 60 min duration. Further, these optimal conditions were tested for the production of a value added product, Bacillus thuringiensis (Bt) which is being used as a biopesticide in the agriculture and forestry sector. It was observed that Bt growth using Fenton oxidized sludge as a substrate was improved with a maximum total cell count of 1.63 × 10⁹ CFU ml^?1 and 96% sporulation after 48 h of fermentation. The results were also tested against ultrasonication treatment and the total cell count was found to be 4.08 × 10⁸ CFU ml^?1 with a sporulation of 90%. Hence, classic Fenton oxidation was demonstrated to be a rather more promising chemical pre-treatment for Bt - based biopesticide production using WWS when compared to ultrasonication as a physical pre-treatment.     

Mineralization of integrated gasification combined-cycle power-station wastewater effluent by a photo-fenton process

The aim of this work was to study the mineralization of wastewater effluent from an integrated-gasification combined-cycle (IGCC) power station sited in Spain to meet the requirements of future environmental legislation. This study was done in a pilot plant using a homogeneous photo-Fenton oxidation process with continuous addition of H₂O₂ and air to the system.The mineralization process was found to follow pseudo-first-order kinetics. Experimental kinetic constants were fitted using neural networks (NNs). The NNs model reproduced the experimental data to within a 90% confidence level and allowed the simulation of the process for any values of the parameters within the experimental range studied. At the optimum conditions (H₂O₂ flow rate = 120 mL/h, [Fe(II)] = 7.6 mg/L, pH = 3.75 and air flow rate = 1 m³/h), a 90% mineralization was achieved in 150 min.Determination of the hydrogen peroxide consumed and remaining in the water revealed that 1.2 mol of H₂O₂ was consumed per each mol of total organic carbon removed from solution. This result confirmed that an excess of dissolved H₂O₂ was needed to achieve high mineralization rates, so continuous addition of peroxide is recommended for industrial application of this process.Air flow slightly improved the mineralization rate due to the formation of peroxo-organic radicals which enhanced the oxidation process.     

Treatment of municipal wastewater using a contact oxidation filtration separation integrated bioreactor

A new contact oxidation filtration separation integrated bioreactor (CFBR) was used to treat municipal wastewater. The CFBR was made up of a biofilm reactor (the upper part of the CFBR) and a gravitational filtration bed (the lower part of the CFBR). Polyacrylonitrile balls (50 mm diameter, 237 m²/m³ specific surface, 90% porosity, and 50.2% packing rate) were filled into the biofilm reactor as biofilm attaching materials and anthracite coal (particle size 1–2 mm, packing density 0.947 g/cm³, non-uniform coefficient (K₈₀ = d₈₀/d₁₀) < 2.0) was placed into the gravitational filtration bed as filter media. At an organic volumetric loading rate of 2.4 kg COD/(m³ d) and an initial filtration velocity of 5 m/h in the CFBR, the average removal efficiencies of COD, ammonia nitrogen, total nitrogen and turbidity were 90.6%, 81.4%, 64.6% and 96.7% respectively, but the treatment process seemed not to be effective in phosphorus removal. The average removal efficiency of total phosphorus was 60.1%. Additionally, the power consumption of the CFBR was less than 0.15 kWh/m³ of wastewater treated, and less than 1.5 kWh/kg BOD₅ removal.     

Treatment of landfill leachates by nanofiltration

Landfill leachate contains high concentrations of organic matter, color, heavy metals and toxic substances. This study presents the feasibility of a commercial nanofiltration membrane (NF-300) in the removal of pollutants from a landfill leachate generated from the Treatment Stabilization and Disposal Facility in Gujarat state of India. Two different leachate samples (Leachates A and B) were collected from the downstream side of closed landfill cells A and B. The average quality of the leachate was 67 719 mg/L COD, 217 mg/L ammonical nitrogen, 22 418 mg/L BOD, 3847 mg/L chlorides and 909 mg/L sulphate. The operating variables studied were applied pressure (4–20 atm), feed flowrate (5–15 L/min) and pH (2, 4, 5.5 and 6.7). It was observed that the solute rejection (R_O) increased with increase in feed pressure and decreased with increase in feed concentration at constant feed flowrate. In the present study, the rejection of cations followed the sequence: R_O (Cr³⁺) > R_O (Ni²⁺) > R_O (Zn²⁺) > R_O (Cu²⁺) > R_O (Cd²⁺) for leachates A and B. The order of solute rejection sequence is inversely proportional to the diffusion coefficients. The rejection of sulphate ions by the NF-300 membrane was 83 and 85%, while the rejection of chlorides was 62 and 65% for leachates A and B, respectively. The NF-300 membrane was characterized by using the combined-film theory-Spiegler–Kedem (CFSK) model based on irreversible thermodynamics and the ion transport model based on the extended Nernst–Planck equation. The membrane transport parameters were estimated using the Levenberg–Marquadt method. The estimated parameters were used to predict the membrane performance and the predicted values are in good agreement with the experimental results.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Kinetics of sulfur dioxide- and oxygen-induced degradation of aqueous monoethanolamine solution during CO2 absorption from power plant flue gas streams

Studies of the kinetics of sulfur dioxide (SO₂)- and oxygen (O₂)-induced degradation of aqueous monoethanolamine (MEA) during the absorption of carbon dioxide (CO₂) from flue gases derived from coal- or natural gas-fired power plants were conducted as a function of temperature and the liquid phase concentrations of MEA, O₂, SO₂ and CO₂. The kinetic data were based on the initial rate which shows the propensity for amine degradation and obtained under a range of conditions typical of the CO₂ absorption process (3–7 kmol/m³ MEA, 6% O₂, 0–196 ppm SO₂, 0–0.55 CO₂ loading, and 328–393 K temperature). The results showed that an increase in temperature and the concentrations of MEA, O₂ and SO₂ resulted in a higher MEA degradation rate. An increase in CO₂ concentration gave the opposite effect. A semi-empirical model based on the initial rate, ?r_MEA = {6.74 × 10⁹ e^?(29,403/RT)[MEA]^0.02([O]^2.91 + [SO₂]^3.52)}/{1 + 1.18[CO₂]^0.18} was developed to fit the experimental data. With the higher order of reaction, SO₂ has a higher propensity to cause MEA to degrade than O₂. Unlike previous models, this model shows an improvement in that any of the parameters (i.e. O₂, SO₂, and CO₂) can be removed without affecting the usability of the model.     

The Austrian P budget as a basis for resource optimization

Phosphorus (P) is a finite and non-substitutable resource that is essential to sustaining high levels of agricultural productivity but is also responsible for environmental problems, e.g., eutrophication. Based on the methodology of Material Flow Analysis, this study attempts to quantify all relevant flows and stocks of phosphorus (P) in Austria, with a special focus on waste and wastewater management. The system is modeled with the software STAN, which considers data uncertainty and applies data reconciliation and error propagation. The main novelty of this work lies in the high level of detail at which flows and stocks have been quantified to achieve a deeper understanding of the system and to provide a sound basis for the evaluation of various management options. The budget confirms on the one hand the dependence of mineral P fertilizer application (2 kg cap⁻¹ yr⁻¹), but it highlights on the other hand considerable unexploited potential for improvement. For example, municipal sewage sludge (0.75 kg cap⁻¹ yr⁻¹) and meat and bone meal (0.65 kg cap⁻¹ yr⁻¹) could potentially substitute 70% of the total applied mineral P fertilizers. However, recycling rates are low for several P flows (e.g., 27% of municipal sewage sludge; 3% of meat and bone meal). Therefore, Austria is building up a remarkable P stock (2.1 kg P cap⁻¹ yr⁻¹), mainly due to accumulation in landfills (1.1 kg P cap⁻¹ yr⁻¹) and agricultural soils (0.48 kg P cap⁻¹ yr⁻¹).     

The use of digital photos to assess visual cover for wildlife in rangelands

Grassland vegetation can provide visual cover for terrestrial vertebrates. The most commonly used method to assess visual cover is the Robel pole. We test the use of digital photography as a more accurate and repeatable method. We assessed the digital photography method on four forage grassland species (Pseudoroegneria spicata, Festuca campestris, Poa pratensis, Achnatherum richardsonii). Digital photos of 2-dimensional cutout silhouettes of three bird species sharp-tailed grouse, western meadowlark and savannah sparrow were used to model the impact of clipping (i.e., grazing) on visual cover. In addition, photos of artificial voles were used to model litter on cover available to small mammals. Nine sites were sampled and data were analyzed by the dominant grass species in each study plot. Regression analysis showed that digital photos (r² = 0.62) were a better predictor than the Robel pole (r² = 0.26) for assessment of cover. Clipping heights showed that clipping at less than 15 cm left the silhouettes 50% exposed. Digital photo analysis revealed that visual cover was affected by the type of grass species, with F. campestris > P. pratensis > A. richardsonii > P. spicata. Biomass and litter were both positively related to cover for small mammals.     

Watershed-scale assessment of arsenic and metal contamination in the surface soils surrounding Miyun Reservoir,Beijing, China

Concentrations of As and selected metals were determined in surface soils of the Miyun Reservoir watershed of Beijing, China. The degree to which concentrations of As and metals exceeded the corresponding background concentration of soils was: Cr > Cu > Zn > As > Ni with no apparent anthropogenic contamination with Cd and Pb. Based on the results of a combination of multivariate statistics and geostatistical analysis, greater concentrations of Cr and Ni in soils were determined to be primarily from iron ore mining near where the Chaohe River enters the northeast portion of the reservoir. Agricultural activities were responsible for the observed elevated concentrations of Cu and Zn in soils. Relatively great concentrations of As were found in soils near the upstream regions of the Baihe River in Chicheng County where small gold mining activities have taken place. The greatest potential for adverse effects of Cr and Cu occurred along the eastern shore of Miyun Reservoir.     

Kinetic studies on the adsorption of phenol, 4-chlorophenol,and 2,4-dichlorophenol from water using activated carbons

This study uses rate parameters in pseudo-first-order (PFO) and pseudo-second-order (PSO) equations (k₁ and k₂q_e, respectively) to judge the extent for approaching equilibrium in an adsorption process. Out of fifty-six systems collected from the literature, the adsorption processes with a k₂q_e value between 0.1 and 0.8 min^?1 account for as much as 70% of the total. These are classified as fast processes. This work compares the validity of PFO and PSO equations for the adsorption of phenol, 4-chlorophenol (4-CP), and 2,4-dichlorophenol (2,4-DCP) on activated carbons prepared from pistachio shells at different NaOH/char ratios. The activated carbons, recognized as microporous materials, had a surface area ranging from 939 to 1936 m²/g. Findings show that the adsorption of phenol, 4-CP, and 2,4-DCP on activated carbons had a k₂q_e value of 0.15–0.58 min^?1, reflecting the fast process. Evaluating the operating time by rate parameters revealed that k₂q_e was 1.6–1.8 times larger than k₁. These findings demonstrate the significance of using an appropriate kinetic equation for adsorption process design.