Treatment and toxicity evaluation of methylene blue using electrochemical oxidation,fly ash adsorption and combined electrochemical oxidation-fly ash adsorption

Treatment of a basic dye, methylene blue, by electrochemical oxidation, fly ash adsorption, and combined electrochemical oxidation-fly ash adsorption was compared. Methylene blue at 100 mg L^?1 was used in this study. The toxicity was also monitored by the Vibrio fischeri light inhibition test.When electrochemical oxidation was used, 99% color and 84% COD were removed from the methylene blue solution in 20 min at a current density of 428 A m^?2, NaCl of 1000 mg L^?1, and pH₀ of 7. However, the decolorized solution showed high toxicity (100% light inhibition).For fly ash adsorption, a high dose of fly ash (>20,000 mg L^?1) was needed to remove methylene blue, and the Freundlich isotherm described the adsorption behavior well.In the combined electrochemical oxidation-fly ash adsorption treatment, the addition of 4000 mg L^?1 fly ash effectively reduced intermediate toxicity and decreased the COD of the electrochemical oxidation-treated methylene blue solution. The results indicated that the combined process effectively removed color, COD, and intermediate toxicity of the methylene blue solution.     

Effect of salinity on metal-complex dye biosorption by Rhizopus arrhizus

In this study the biosorption of Yellow RL, a metal-complex anionic dye, by dried Rhizopus arrhizus, a filamentous fungus, was investigated as a function of initial solution pH, initial dye concentration and initial salt (sodium chloride) concentration. The fungus exhibited the maximal dye uptake at pH 2 in the absence and in the presence of salt. Dye uptake increased with the dye concentration up to 1000 mg l^?1 and diminished considerably in the presence of increasing concentrations of salt up to 50 g l^?1. The fungus biosorbed 85.4 mg dye g^?1of dried biomass at 100 mg l^?1 initial dye concentration in the absence of salt. When 50 g l^?1 salt was added to the biosorption medium, this value dropped to 60.8 mg g^?1 resulting in 28.8% reduction in biosorption capacity. The Redlich–Peterson and Langmuir–Freundlich were the most suitable adsorption models for describing the biosorption equilibrium data of the dye both individually and in salt containing medium. The pseudo-second-order and saturation type kinetic models depicted the biosorption kinetics accurately for all cases studied. Equilibrium and kinetic constants varied with the level of salt were expressed as a function of salt concentration.     

Treatment of municipal wastewater using a contact oxidation filtration separation integrated bioreactor

A new contact oxidation filtration separation integrated bioreactor (CFBR) was used to treat municipal wastewater. The CFBR was made up of a biofilm reactor (the upper part of the CFBR) and a gravitational filtration bed (the lower part of the CFBR). Polyacrylonitrile balls (50 mm diameter, 237 m²/m³ specific surface, 90% porosity, and 50.2% packing rate) were filled into the biofilm reactor as biofilm attaching materials and anthracite coal (particle size 1–2 mm, packing density 0.947 g/cm³, non-uniform coefficient (K₈₀ = d₈₀/d₁₀) < 2.0) was placed into the gravitational filtration bed as filter media. At an organic volumetric loading rate of 2.4 kg COD/(m³ d) and an initial filtration velocity of 5 m/h in the CFBR, the average removal efficiencies of COD, ammonia nitrogen, total nitrogen and turbidity were 90.6%, 81.4%, 64.6% and 96.7% respectively, but the treatment process seemed not to be effective in phosphorus removal. The average removal efficiency of total phosphorus was 60.1%. Additionally, the power consumption of the CFBR was less than 0.15 kWh/m³ of wastewater treated, and less than 1.5 kWh/kg BOD₅ removal.     

Effect of feeding strategy and COD/sulfate ratio on the removal of sulfate in an AnSBBR with recirculation of the liquid phase

The objective of this work was to analyze the effect of the interaction between feeding strategy and COD/sulfate ratio on the removal efficiency of sulfate and organic matter from a synthetic wastewater. An anaerobic sequencing batch reactor with recirculation of the liquid phase and containing immobilized biomass on polyurethane foam (AnSBBR) was used. The AnSBBR with a total volume of 3.7 L, treated 2.0 L synthetic wastewater in 8-h cycles at 30 ± 1 °C and was inoculated with anaerobic biomass from a UASB. Two feeding strategies were assessed: (a) batch and (b) batch followed by fed-batch. In strategy (a) the reactor was fed in 10 min with 2 L wastewater containing sulfate and carbon sources. In strategy (b) 1.2 L wastewater (containing only the sulfate source) was fed during the first 10 min of the cycle and the remaining 0.8 L (containing only the carbon source) in 240 min. The COD/sulfate ratios assessed were 1 and 3. Based on these values and on the concentrations of organic matter (0.5–11.25 gCOD/L) and sulfate (0.5 and 2.5 gSO₄^2?/L), the sulfate and organic matter loading rates applied equaled 1.5 and 4.5 gSO₄^2?/L d for sulfate and 1.5, 4.5 and 13.5 gCOD/L d for organic matter. After stabilization of the system time profiles were run of monitored parameters (COD, sulfate, sulfide and sulfite). In general, the reactor showed to be robust for use in the anaerobic treatment of wastewaters containing sulfate. Gradual feeding (strategy b) of the carbon source favored sulfate reduction, resulting in sulfate removal efficiencies of 84–98% and organic matter removal efficiencies of 48–95%. The best results were observed under COD/sulfate ratio equal to 1 (loading rates of 1.5 and 4.5 gSO₄^2?/L d for sulfate, and 1.5 and 4.5 gCOD/L d for organic matter). When COD/sulfate ratio was 3 (loading rates of 1.5 and 4.5 gSO₄^2?/L d for sulfate, and 4.5 and 13.5 gCOD/L d for organic matter) the effect of feed mode became less significant. These results show that the strategy batch followed by fed-batch is more advantageous for COD/sulfate ratios near the stoichiometric value (0.67) and higher organic matter and sulfate concentrations.     

Energy balances,greenhouse gas emissions and economics of biochar production from palm oil empty fruit bunches

This paper presents results from a gate-to-gate analysis of the energy balance, greenhouse gas (GHG) emissions and economic efficiency of biochar production from palm oil empty fruit bunches (EFB). The analysis is based on data obtained from EFB combustion in a slow pyrolysis plant in Selangor, Malaysia. The outputs of the slow pyrolysis plant are biochar, syngas, bio-oil and water vapor. The net energy yield of the biochar produced in the Selangor plant is 11.47 MJ kg⁻¹ EFB. The energy content of the biochar produced is higher than the energy required for producing the biochar, i.e. the energy balance of biochar production is positive. The combustion of EFB using diesel fuel has the largest energy demand of 2.31 MJ kg⁻¹ EFB in the pyrolysis process. Comparatively smaller amounts of energy are required as electricity (0.39 MJ kg⁻¹ EFB) and for transportation of biochar to the warehouse and the field (0.13 MJ kg⁻¹ EFB). The net greenhouse gas emissions of the studied biochar production account for 0.046 kg CO₂-equiv. kg⁻¹ EFB yr⁻¹ without considering fertilizer substitution effects and carbon accumulation from biochar in the soil. The studied biochar production is profitable where biochar can be sold for at least 533 US-$ t⁻¹. Potential measures for improvement are discussed, including higher productivity of biochar production, reduced energy consumption and efficient use of the byproducts from the slow pyrolysis.     

Closing the water cycle for industrial laundries: An operational performance and techno-economic evaluation of a full-scale membrane bioreactor system

To reduce the consumption of freshwater in the laundry industry, a new trend of closing the water cycle has resulted in the reuse/recycling of water. In this study, the performance of a full-scale submerged aerobic membrane bioreactor (9 m³) used to treat/reuse industrial laundry wastewater was examined over a period of 288 days. The turbidity and total solids (TS) were reduced by 99%, and the chemical oxygen demand (COD) effluent removal efficiencies were between 70% and 99%. The levels of COD removed by the membrane were significantly greater than the levels of biodegraded COD. This enabled the bioreactor to sustain COD levels that were below 100 mg/L, even during periods of low wastewater biodegradation due to bioreactor sludge. An economic evaluation of the membrane bioreactor (MBR) system showed a savings of 1.13 € per 1 m³ of water. The payback period for this system is approximately 6 years. The energy and maintenance costs represent only 5% of the total cost of the MBR system.     

Surface water and wastewater treatment using a new tannin-based coagulant. Pilot plant trials

A new tannin-based coagulant-flocculant (Tanfloc) was tested for water treatment at a pilot plant level. Four types of water sample were treated: surface water (collected from a river), and municipal, textile industry (simulated by a 100 mg L^?1 aqueous solution of an acid dye), and laundry (simulated by a 50 mg L^?1 aqueous solution of an anionic surfactant) wastewaters. The pilot plant process consisted of coagulation, sedimentation, and filtration. The experiments were carried out with an average coagulant dosage of 92.2 mg L^?1 (except in the case of the surface water for which the dosage was 2 mg L^?1). The efficacy of the water purification was notable in every case: total turbidity removal in the surface water and municipal wastewater, about 95% dye removal in the case of the textile industry wastewater, and about 80% surfactant removal in the laundry wastewater. Filtration improved the removal of suspended solids, both flocs and turbidity, and slightly improved the process as a whole. The efficiency of Tanfloc in these pilot studies was similar to or even better than that obtained in batch trials.     

Greening of production in metal processing industry through process modifications and improved management practices

Although it was indicated through various studies from around the world that resource efficiency can be adapted in metal processing plants, a very limited number of projects could be realized in Turkish metal processing industry so far. In this study it was aimed at investigating process modifications and management practices to increase water and chemical use efficiency thus increasing environmental and economic performance of a metal processing company. As a result of the applications in heat treatment and zinc phosphating processes total water consumption of the company was reduced by 34.1% corresponding to an annual water saving of 18,831 m³. Moreover, total chemical consumption in zinc phosphating as one of the most chemical intensive processes in the company, was decreased by 1401 kg/year (26.1%). Applications in zinc phosphating process led to a significant decrease in the amount of treated wastewater and wastewater treatment sludge which is labelled as hazardous waste according to national legislations. Total wastewater generation was decreased by 3255 m³/year (50.9%) while wastewater treatment sludge was reduced 4656 kg/year (16.9%). Moreover, energy consumption of the company was reduced by 32.647 kW h/year which corresponds to 36% energy saving in water pumping. Implementation cost of the applications were 34,233$ which is calculated to be paid back in 2.3 years. This study is expected to fill a gap in Turkey by demonstrating that environmental performance in metal processing industry could be improved by process modifications and improved management practices resulting in tangible economic gains.     

Effect of impeller type and agitation on the performance of pilot scale ASBR and AnSBBR applied to sanitary wastewater treatment

The objective of this work was to assess the effect of agitation rate and impeller type in two mechanically stirred sequencing batch reactors: one containing granulated biomass (denominated ASBR) and the other immobilized biomass on polyurethane foam (denominated AnSBBR). Each configuration, with total volume of 1 m³, treated 0.65 m³ sanitary wastewater at ambient temperature in 8-h cycles. Three impeller types were assessed for each reactor configuration: flat-blade turbine impeller, 45°-inclined-blade turbine impeller and helix impeller, as well as two agitation rates: 40 and 80 rpm, resulting in a combination of six experimental conditions. In addition, the ASBR was also operated at 20 rpm with a flat-blade turbine impeller and the AnSBBR was operated with a draft tube and helix impeller at 80 and 120 rpm. To quantify how impeller type and agitation rate relate to substrate consumption rate, results obtained during monitoring at the end of the cycle, as well as the time profiles during a cycle were analyzed. Increasing agitation rate from 40 rpm to 80 rpm in the AnSBBR improved substrate consumption rate whereas in the ASBR this increase destabilized the system, likely due to granule rupture caused by the higher agitation. The AnSBBR showed highest solids and substrate removal, highest kinetic constant and highest alkalinity production when using a helix impeller, 80 rpm, and no draft tube. The best condition for the ASBR was achieved with a flat-blade turbine impeller at 20 rpm. The presence of the draft tube in the AnSBBR did not show significant improvement in reactor efficiency. Furthermore, power consumption studies in these pilot scale reactors showed that power transfer required to improve mass transfer might be technically and economically feasible.     

Nitrogen critical loads and management alternatives for N-impacted ecosystems in California

Empirical critical loads for N deposition effects and maps showing areas projected to be in exceedance of the critical load (CL) are given for seven major vegetation types in California. Thirty-five percent of the land area for these vegetation types (99,639 km²) is estimated to be in excess of the N CL. Low CL values (3–8 kg N ha^?1 yr^?1) were determined for mixed conifer forests, chaparral and oak woodlands due to highly N-sensitive biota (lichens) and N-poor or low biomass vegetation in the case of coastal sage scrub (CSS), annual grassland, and desert scrub vegetation. At these N deposition critical loads the latter three ecosystem types are at risk of major vegetation type change because N enrichment favors invasion by exotic annual grasses. Fifty-four and forty-four percent of the area for CSS and grasslands are in exceedance of the CL for invasive grasses, while 53 and 41% of the chaparral and oak woodland areas are in exceedance of the CL for impacts on epiphytic lichen communities. Approximately 30% of the desert (based on invasive grasses and increased fire risk) and mixed conifer forest (based on lichen community changes) areas are in exceedance of the CL. These ecosystems are generally located further from emissions sources than many grasslands or CSS areas. By comparison, only 3–15% of the forested and chaparral land areas are estimated to be in exceedance of the NO₃^? leaching CL. The CL for incipient N saturation in mixed conifer forest catchments was 17 kg N ha^?1 yr^?1. In 10% of the CL exceedance areas for all seven vegetation types combined, the CL is exceeded by at least 10 kg N ha^?1 yr^?1, and in 27% of the exceedance areas the CL is exceeded by at least 5 kg N ha^?1 yr^?1. Management strategies for mitigating the effects of excess N are based on reducing N emissions and reducing site N capital through approaches such as biomass removal and prescribed fire or control of invasive grasses by mowing, selective herbicides, weeding or domestic animal grazing. Ultimately, decreases in N deposition are needed for long-term ecosystem protection and sustainability, and this is the only strategy that will protect epiphytic lichen communities.     

Physicochemical characterization of hydroxyapatite and its application towards removal of nitrate from water

A laboratory study was conducted to investigate the efficiency of hydroxyapatite (HAP) towards removal of nitrate from synthetic nitrate solution. In the present research HAP synthesized from egg-shell was characterized using SEM, XRD, FTIR and TGA–DSC. The removal of nitrate was 96% under neutral conditions, using 0.3 g of adsorbent in 100 mL of nitrate solution having an initial concentration of 100 mg/L. An adsorption kinetic study revealed that the adsorption process followed first order kinetics. Adsorption data were fitted to a linearly transformed Langmuir isotherm with correlation coefficient (R²) > 0.98. Thermodynamic parameters were also calculated to study the effect of temperature on the removal process. In order to understand the adsorption type, equilibrium data were tested with the Dubinin–Radushkevich isotherm. The process was rapid and equilibrium was established within the first 40 min.     

Lead accumulation in different Chinese cabbage cultivars and screening for pollution-safe cultivars

Recently, the concept of pollution-safe cultivars (PSCs) was proposed to minimize the influx of pollutants to the human food chain. Variations in lead (Pb) uptake and translocation among Chinese cabbage (Brassica pekinensis L.) cultivars were investigated in a pot-culture experiment and a field-culture experiment to screen out Pb-PSCs for food safety. The results of the pot-culture experiment showed that shoot Pb concentrations under two Pb treatments (500 and 1500 mg kg^?1) varied significantly (p < 0.05) between cultivars, with average values of 3.01 and 6.87 mg kg^?1, respectively. Enrichment factors (EFs) and translocation factors (TFs) in cultivars were less than 0.50 and varied significantly (p < 0.05) between cultivars. Shoot Pb concentrations in 12 cultivars under treatment T₁ (500 mg kg^?1) were lower than 2.0 mg kg^?1. The field-culture experiment further confirmed Qiuao, Shiboqiukang and Fuxing 80 as Pb-PSCs, which were suitable to be cultivated in low-Pb (<382.25 mg kg^?1) contaminated soils and harmless to human health as foods.     

Subsoil TPH contamination in two oil pipeline pumping stations and one pipeline right-of-way in north Mexico

This investigation deals with the characterization carried out in zones around two pipeline pumping stations and one pipeline right-of-way in the north of Mexico. In particular those areas where contamination was evaluated: (a) south area of the separation ditch in the Avalos station, (b) the area between the separation ditch at the Avalos station, (c) km 194 + 420 of the Moctuzma station, and (d) km 286 + 900 in the Candelaria station. Results of this investigation showed that only four samples showed TPH values higher than the Mexican limit for 2004: AVA 1B, with 21,191 mg kg^?1; AVA 1C, with 9348 mg kg^?1; AVA 2B, with 13,970 mg kg^?1; and MOC 2A, with 4108 mg kg^?1.None of the sampled points showed the presence of PAHs at values higher than those found in the Mexican or American legislations. PAH were detected in the range of 0.0004 and 13.05 mg kg^?1.It is suggested to implement surfactant soil washing as a remediation technique for the approximately 600 m³ that need to be treated.     

Flocculation performance of epichlorohydrin-dimethylamine polyamine in treating dyeing wastewater

Epichlorohydrin-dimethylamine polymers with different intrinsic viscosity (η) and cationicity (τ) were synthesized. The flocculation performance and mechanism of these polymers in the removal of the reactive and disperse dyes from synthetic wastewater was investigated in terms of flocculation dynamics and color removal efficiency. The polymer flocculation efficiency was compared with that of polyaluminum chloride (PAC) and a composite flocculant based on polyaluminum chloride-epichlorohydrin-dimethylamine polyamine. The results showed that epichlorohydrin-dimethylamine polymer was effective over a pH range of 2–10 for the reactive and disperse dye removal (Reactive Brilliant Red and Disperse Yellow dyes). Epichlorohydrin-dimethylamine polymer with the highest η and τ gave the best reactive dye removal efficiency, and its adsorption-bridging and electric neutralization ability played important roles in the flocculation process. The higher the η viscosity of the epichlorohydrin-dimethylamine polymer, the better the flocculation performance of epichlorohydrin-dimethylamine polyamine, and stronger adsorption-bridging ability was obtained for removing the disperse dye from dyeing wastewaters. Epichlorohydrin-dimethylamine polymer achieved better decolorization performance when used together with PAC.     

Optimization of Fenton oxidation pre-treatment for B. thuringiensis – Based production of value added products from wastewater sludge

Fenton oxidation pretreatment was investigated for enhancement of biodegradability of wastewater sludge (WWS) which was subsequently used as substrate for the production of value- added products. The Response surface method with fractional factorial and central composite designs was applied to determine the effects of Fenton parameters on solubilization and biodegradability of sludge and the optimization of the Fenton process. Maximum solubilization and biodegradability were obtained as 70% and 74%, respectively at the optimal conditions: 0.01 ml H₂O₂/g SS, 150 [H₂O₂]₀/[Fe²⁺]₀, 25 g/L TS, at 25 °C and 60 min duration. Further, these optimal conditions were tested for the production of a value added product, Bacillus thuringiensis (Bt) which is being used as a biopesticide in the agriculture and forestry sector. It was observed that Bt growth using Fenton oxidized sludge as a substrate was improved with a maximum total cell count of 1.63 × 10⁹ CFU ml^?1 and 96% sporulation after 48 h of fermentation. The results were also tested against ultrasonication treatment and the total cell count was found to be 4.08 × 10⁸ CFU ml^?1 with a sporulation of 90%. Hence, classic Fenton oxidation was demonstrated to be a rather more promising chemical pre-treatment for Bt - based biopesticide production using WWS when compared to ultrasonication as a physical pre-treatment.     

Analytical solution for Joule–Thomson cooling during CO2 geo-sequestration in depleted oil and gas reservoirs

Mathematical tools are needed to screen out sites where Joule–Thomson cooling is a prohibitive factor for CO₂ geo-sequestration and to design approaches to mitigate the effect. In this paper, a simple analytical solution is developed by invoking steady-state flow and constant thermophysical properties. The analytical solution allows fast evaluation of spatiotemporal temperature fields, resulting from constant-rate CO₂ injection. The applicability of the analytical solution is demonstrated by comparison with non-isothermal simulation results from the reservoir simulator TOUGH2. Analysis confirms that for an injection rate of 3 kg s^?1 (0.1 MT yr^?1) into moderately warm (>40 °C) and permeable formations (>10^?14 m² (10 mD)), JTC is unlikely to be a problem for initial reservoir pressures as low as 2 MPa (290 psi).     

Butyltin occurrence and risk assessment in the sediments of the Iberian Peninsula

The occurrence of butyltin (BT) compounds in more than 50 recent sediment samples of the Iberian Peninsula, collected in the harbours of the western Mediterranean Sea (Spain) and the North Atlantic Ocean (Portugal), including domestic and industrial sewage disposal sites, has been assessed. The highest levels of tributyltin (TBT) (7673 μg kg^?1 dry wt.) were detected in commercial harbours associated with inputs from large vessels. However, relatively high TBT values (about 2150 μg kg^?1 dry wt.) were also detected in fishing and recreational boating areas. Spanish marinas and harbours are more polluted in terms of TBT (5–7673 μg kg^?1 dry wt.) compared to those in Portugal (4–12 μg kg^?1 dry wt.). Generally, the Mediterranean sediments show a BT distribution characterized by the predominance of TBT over the degradation products dibutyl (DBT) and monobutyltin (MBT), indicating the presence of recent inputs, in contrast to the Portuguese coastal distribution. Calculation of butyltin degradation indexes (BDI) confirmed a different trend, depending on the area. Furthermore, a comparative study of the occurrence of BT in different sewage sludge disposal sites shows that domestic primary sewage sludge effluents can contribute to coastal BT pollution, but to a lesser extent when compared with harbours. Historical trends (1995–2003) for Barcelona harbour reveal that BT regulations on the use of TBT-based antifouling paints have not been fully effective. Finally, a comparison against the existing sediment quality guidelines (SQGs) indicated that acute toxic effects could only be expected for TBT in some Mediterranean harbours; conversely, in every North Atlantic Ocean station, a lesser environmental threat for the harbour benthic community is expected.     

Emergy evaluation of an integrated livestock wastewater treatment system

Wastewater treatment practices should pay more attention to their environmental performances due to their resources consumption and emissions’ impact. While reclaimed water reuse seems to have become a promising practice, is it always feasible in any condition? To address this issue, this study carried out an extended emergy evaluation of a holistic wastewater treatment system. On one hand, this method was extended to include the emissions’ impact. On the other hand, this study integrated a wastewater treatment plant, its excess sludge disposal system and treated water disposal system into an integrated wastewater treatment system (IWTS), so as to evaluate its performances more completely. And then several indicators, including cost per unit pollutant eliminated (CUPE), ratio of positive output (RPO), environmental load ratio (ELR), and sustainability index (SI), were proposed for evaluating the performances of an IWTS. Two scenarios (scenario A: wastewater treatment + sludge landfilling + treated water discharges; scenario B: wastewater treatment + sludge landfilling + reclaimed water reuse) for a livestock wastewater treatment plant in Sichuan Agricultural University located in Ya’an City in Southwest China, as cases, were researched. The results show that scenario B has lower positive output efficiency and greater environmental load than scenario A. Meanwhile, the reclaimed water reuse raises cost per unit pollutant eliminated compared with the treated water being discharged directly; emissions’ impact enhances the environmental load of the two scenarios to different degree; emissions’ impact has decisive effect on the sustainability of the two scenarios. These results mean that the reclaimed water reuse should not be advocated in this case. This study provides some policy implications: (1) wastewater treatment process should be comprehensively evaluated from its resources consumption and impact of emissions; (2) reclaimed water reuse should be carefully evaluated from its pros and cons simultaneously; (3) the local conditions should be considered when implementing reclaimed water reuse, such as local water body conditions, market demands, the related laws and regulations, corporations’ economic conditions, etc.     

Application of carbon adsorbents prepared from Brazilian-pine fruit shell for the removal of reactive orange 16 from aqueous solution: Kinetic,equilibrium, and thermodynamic studies

Activated (AC-PW) and non-activated (C-PW) carbonaceous materials were prepared from the Brazilian-pine fruit shell (Araucaria angustifolia) and tested as adsorbents for the removal of reactive orange 16 dye (RO-16) from aqueous effluents. The effects of shaking time, adsorbent dosage and pH on the adsorption capacity were studied. RO-16 uptake was favorable at pH values ranging from 2.0 to 3.0 and from 2.0 to 7.0 for C-PW and AC-PW, respectively. The contact time required to obtain the equilibrium using C-PW and AC-PW as adsorbents was 5 and 4 h at 298 K, respectively. The fractionary-order kinetic model provided the best fit to experimental data compared with other models. Equilibrium data were better fit to the Sips isotherm model using C-PW and AC-PW as adsorbents. The enthalpy and entropy of adsorption of RO-16 were obtained from adsorption experiments ranging from 298 to 323 K.