Effect of MgO and CaO/SiO2 on the immobilization of chromium in synthetic slags

This work investigated the chemical and mineralogical properties of CaO–SiO₂–Cr₂O₃–CaF₂–MgO slags. Synthetic slags were prepared and the effect of the slag basicity (mass ratio CaO/SiO₂) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by X-ray powder diffraction (XRD) and scanning electron microscope-energy dispersive spectroscopy (SEM–EDS), whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO₂?=?1, the main Cr-compound was MgCr₂O₄ spinel, which forms octahedron crystals. Small amounts of CaCr₂O₄ and CaCrO₄ were also observed. It was found that with increasing the slag basicity from 1 to 2 the compounds MgCr₂O₄ and CaCr₂O₄ were formed together with the Cr(V)-containing compound complex Ca₅(CrO₄)₃F which forms hexagonal crystals. The results showed that the highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO₂?=?2, probably owing to the formation of CaCrO₄ and Ca₅(CrO₄)₃F, whilst the lowest chromium concentration levels corresponded to MgO-based slags owing to the stable binding of chromium in spinel with MgO. Additionally, potential–pH diagrams for the Ca–Cr–H₂O and Mg–Cr–H₂O systems at 25?°C were calculated.     

An examination of the exothermic nature of fluidized bed combustion (FBC) residues

Circulating fluidized bed combustion (CFBC) ashes from nine operational periods at the 183 MWe CFBC boiler at Point Aconi were examined for exothermic behaviour. Bed ashes and fly ashes were investigated using a Parr 1455 solution calorimeter. Limited tests were also carried out with additional samples from Point Aconi and from the 160 MWe TVA Bubbling Fluidized Bed Combustion boiler to evaluate the effects of particle size and aging on exothermic behaviour. For the Point Aconi ashes, heat release from the bed ash ranged from 11 to 52 J/g, and the maximum heat release rates ranged from 0.06 to 0.17 J/g/s. For the fly ash heat release varied from 114 to 187 J/g and the maximum heat release rates ranged from 0.8 to 1.9 J/g/s. In the fly ash samples, 50% or more of available CaO was converted to Ca(OH)₂, while for the bed ash a third or less of the CaO was converted to Ca(OH)₂. The exothermicity of the bed ash is directly proportional to the CaO content of the ash. However, this is not true for the fly ash. The exothermic behaviour of fresh FBC ash appeared to be greatly reduced by exposure in air over a 48-h period. Another conclusion of this work is that particle size effects the exothermic behaviour.     

利用含铝废盐酸制备聚合氯化铝

以某医药企业产生的含铝废盐酸为原料制备了液体聚合氯化铝(PAC)。确定了适宜的有机物去除方法和碱化剂,考察了碱化剂投加量、废盐酸铝离子含量等合成条件对PAC产品指标的影响,并比较了自制PAC和市售PAC对该企业污水站二沉池出水的混凝效果。实验结果表明:采用活性炭吸附法去除废盐酸中有机物,选择固体Ca O作为碱化剂,在活性炭投加量1‰(w)、吸附时间1 h、铝离子含量9.5%(w,以Al_2O_3计)、CaO投加量80 g/L、反应时间24 h的条件下,制备的液体PAC达到行业标准HG/T 2677—2017《工业聚氯化铝》中的Ⅲ类标准;自制PAC对废水COD和SS的去除率均优于市售PAC,不仅可替代其使用,还可外售产生经济效益。     

Improved preparation of recycled polymers in chemical recycling of fiber-reinforced plastics and molding of test product using recycled polymers

We examined an improved preparation method of recycled unsaturated polyester resin from recovered monomeric materials obtained from the depolymerization of fiber-reinforced plastics (FRPs). The formation of unsaturated polyester progressed smoothly in the presence of catalytic amounts of Ca(OAc)₂ and Ti(OBu)₄. The quality of the resin was estimated by the durometer hardness test. The strength test of FRP board prepared from recycled resin showed sufficient hardness for practical use (about 94% of the tensile strength of new resin). We examined the recycled resin by using it to mold successfully an actual test product.     

湿法烟气脱硫石膏制备硫酸铵

采用湿法烟气脱硫石膏为原料,与( NH4)2CO3反应,制备(NH4)2SO4.通过X射线衍射仪表征可知:脱硫石膏的主要成分为CaSO4,反应后CaSO4中的Ca2+大部分以CaCO3形式存在于固体沉淀物中,CaCO3粉末平均粒径为80 nm;而原先CaSO4中的不溶性SO2-4则与NH+4结合生成(NH4)2SO4,...     

生态修复植物蜈蚣草中砷的回收

采用管式炉高温热解-NaOH-Na₂CO₃混合液碱浸-CuSO₄·5H₂O沉淀的方法回收生态修复植物蜈蚣草中的砷，最终得到产品砷酸铜。该方法的最佳工艺条件为：热解温度600 ℃，热解时间30 min，CaO加入量（CaO与蜈蚣草的质量比）8%； m（NaOH）∶m（Na₂CO₃）=1∶3，碱浸温度70 ℃， 碱浸时间2 h， 固液比1∶10； 沉淀反应pH 5， 沉淀反应温度70 ℃。采用该方法处理生态修复植物蜈蚣草，得到产品砷酸铜的纯度为93%，砷回收率达88%。     

碳纳米管-海藻酸钠复合吸附材料的制备及其对高浓度Cr（Ⅲ）的吸附

以碳纳米管（CNTs）和海藻酸钠（SA）为主要原料，制备了环境友好型的复合吸附材料——CNTs-SA。采用TEM和FTIR技术对吸附材料进行了表征，并采用静态法考察了溶液pH、吸附时间、原料固液比（m（CNTs）∶V（SA））等因素对CNTs-SA吸附Cr（Ⅲ）的影响。表征结果显示，CNTs-SA表面引入了更多的—COOH和—CO基团，导致其吸附Cr（Ⅲ）的效果较CNTs有了显著的提高。实验结果表明：在室温、初始Cr（Ⅲ）质量浓度4 000 mg/L、CNTs-SA加入量21 mg/mL、溶液pH 5、吸附时间3 h、m（CNTs）∶V（SA）=1.0 mg/mL的条件下，CNTs-SA对Cr（Ⅲ）的吸附量为120 mg/g，Cr（Ⅲ）去除率为61.5%;Freundlich等温吸附方程适合描述CNTs-SA对Cr（Ⅲ）的吸附行为。     

用电解锰阳极泥和含SO_2工业尾气制备硫酸锰

以电解锰阳极泥与电解锌生产中产生的含SO_2尾气为原料,经过反应、浸出、浸出液两次净化和浓缩结晶制备硫酸锰,考察了反应时间、含SO_2尾气的流量及反应温度对Mn~(4+)转化率的影响.实验结果表明:在反应时间45 min、反应温度20～30 ℃、含SO_2尾气流量16 L/min的条件下,Mn~(4+)转化率达90%以上;尾气中SO_2利用率随尾气流量增加而降低;所得MnSO_4·H_2O产品质量达到GB1622-86<工业级硫酸锰标准>.     

Production of brown and black pigments by using flotation waste from copper slag.

One of the major problems in copper-producing countries is the treatment of the large amount of copper slag or copper flotation waste generated from copper slag which contains significant amounts of heavy metals such as Cu, Zn, Pb and Co. Dumping or disposal of such large quantities of flotation waste from copper slag causes environmental and space problems. In this study, the treatment of flotation waste from copper slag by a thermal method and its use as an iron source in the production of inorganic brown and black pigments that are used in the ceramic industry were investigated. The pigments were produced by calcining different amounts of flotation waste and chromite, Cr2O3, ZnO and CoO mixtures. The pigments obtained were added to transparent ceramic glazes and porcelainized tile bodies. Their colours were defined by L*a*b* measurements with a spectrophotometer. The results showed that flotation waste from copper slag could be used as an iron source to produce brown and black pigments in both ceramic body and glazes.     

The use of 'exotic' framework structures in waste management

The use of porous framework materials in waste management applications has the potential to be a powerful tool in toxic metal remediation. The properties that these materials possess, including high surface area and ion-exchange capacity, are theoretically valuable. Furthermore, the flexibility of many of these frameworks allows the potential for immobilisation of waste materials with the framework of the material, in addition to the traditional capture in the pore structure. However, for either of these routes to be useful for waste management purposes, these structures must also be stable in any proposed storage media. This study examines the stability of a range of porous materials whose frameworks are made out of zinc and arsenic, both considered toxic minesite wastes, when exposed to aqueous media. The three frameworks examined (sodalite analogue Na(6)(H(2)O)(8)(ZnAsO(4))(6), open framework K(3)Zn(4)O(AsO(4))(3).3.5H(2)O, and an ABW type framework NH(4)ZnAsO(4)) all have similar hydrothermal synthetic routes and bulk framework compositions, but differ in counter ion used, pore size and complexity of structure. The phases were examined before and after storage in an aqueous environment, and their crystallinity and leaching were determined. All phases prepared were found to be extremely unstable outside their original synthetic environment, and very soluble when exposed to water, calling into question their practical use in any environment.     

Characterization of alkali-activated thermally treated incinerator bottom ash

The fine fraction (<14mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8MPa. The new materials may have potential for use as controlled low-strength materials.     

The chemical characteristics of ashes from cattle, swine and poultry manure

Animal manure is waste that contains large amounts of fertilizer resources. Incineration technology is effective in decreasing the volume of animal manure and concentrating the nutrients. In this study, the nutrient concentration and chemical compounds of several types of animal manure ash were examined to promote their recycling for agriculture. The nutrient concentration of manure ash was dependent on the reduction rate of solid materials by incineration. The phosphorus (P) and potassium (K) of cattle and layer manure were not concentrated greatly because of high silicon (Si) and calcium (Ca) concentrations, respectively. On the other hand, the P concentration of swine manure and broiler litter was increased to 10.1–12.0 % (3.6–4.6 times compared with original materials), equivalent to that of phosphate rock used as fertilizer material. The K concentration of broiler litter ash (16.1 %) was highest of all. The phosphate compounds of cattle and swine manure ashes were determined as Ca₉Fe(PO₄)₇ or Ca₉MgK(PO₄)₇. Hydroxyapatite (Ca₅(PO₄)₃(OH)) was detected in layer manure and broiler litter ashes. By acid treatment of ash, P and K availability of the fertilizer made from layer manure ash (33 % of materials) was equivalent to that of conventional chemical fertilizer.     

Improved method for the formation of recycled resins from depolymerized products of waste fiber-reinforced plastics: simple and effective purification of recovered monomers by washing with water

The synthesis of recycled plastics from recovered monomeric materials obtained from the depolymerization reaction of fiber-reinforced plastics (FRP) was examined. The depolymerization reaction of FRP in the presence of N,N-dimethylaminopyridine (DMAP) smoothly yielded the corresponding monomers, which mainly consisted of dimethyl phthalates. The polymerization reaction with this monomer failed to form the corresponding unsaturated polyesters due to contamination by N-methyl-4-pyridone, a decomposition product of DMAP. An efficient purification of the recovered monomer was achieved by washing with water, and the purified monomer successfully yielded the corresponding polymers. A hardness test revealed that the polymers were as hard as the polyester made from virgin materials. The present modification provides a practical method for the preparation of recycled plastics from depolymerized plastics.     

Recovery of Nd and Dy from rare earth magnetic waste sludge by hydrometallurgical process

This paper describes a hydrometallurgical process for recovering neodymium (Nd) and dysprosium (Dy) from a magnetic waste sludge generated from the Nd–Fe–B(–Dy) manufacturing process. Phase analysis by XRD study revealed Nd(OH)₃ and Fe₂O₃ as main mineral phases, and chemical analysis by ICP showed the contents of 35.1 wt% Nd, 29.5 wt% Fe, 1.1 wt% Dy and 0.5 wt% B. A solution of 1 M HNO₃ + 0.3 M H₂O₂ was used to dissolve up to 98 % Nd and 81 % Dy, while keeping Fe dissolution below 15 % within 10 min. Fe dissolved in solution was completely removed as Fe(OH)₃ at pH 3 followed by precipitation of Nd and Dy with oxalic acid (H₂C₂O₄) and recovered 91.5 % of Nd and 81.8 % of Dy from solution. The precipitate containing Nd and Dy was calcined at 800 °C to obtain Nd₂O₃ as final product with 68 % purity, and final recovery of 69.7 % Nd and 51 % of Dy was reported in this process.     

Oxygen Permeability and Biodegradability of Polyuronic Acids Prepared from Polysaccharides by TEMPO-Mediated Oxidation

Polyuronic acids, i.e., amylouronic acid, cellouronic acid and chitouronic acid, were prepared from starch, cellulose and chitin, respectively, by the 2,2,6,6-tetramethylpiperidine-1-oxy radical (TEMPO)-mediated oxidation, and their gas-barrier properties and biodegradability were studied in consideration to use the polyuronic acids as flexible packaging films or coating materials. Cellouronic acid and amylouronic acid had excellent oxygen-barrier properties similar to that of poly(vinyl alcohol) (PVA), while chitouronic acid did not. The regular chemical structures of the former two polyuronic acids with no bulky substituents or adducts may have brought about such high oxygen-barrier levels. An oxidized product prepared form fine microcrystalline cellulose by the TEMPO-mediated oxidation was not completely dissolved in water, but became a paste. However, this paste also formed sufficiently smooth films by coating, and had good gas-barrier property. All polyuronic acids prepared were biodegradable; cellouronic acid and chitouronic acid had high degrees of biodegradability, while amylouronic acid had quite low value. These various characteristics are significant for end use of these new polyuronic acids as gas-barrier materials for biodegradable packaging.     

Solidification/stabilization Process For Steel Foundry Dust Using Cement Based Binders: Influence Of Processing Variables

The influence of processing variables: mixing time, waste/binder ratio and water/solid ratio on the solidification/stabilization process of steel foundry dust has been studied. The characterization of the final product was based on the Toxic Characterization Leaching Procedure (TCLP) followed by the biotoxicity (bioluminescence assay) and concentration of the metals, Cr, Cd, Pb and Zn in the leachates. The final product characteristics depend mainly on the waste/binder ratio, as a function of the metal hydroxide solubilities. The results of this work allow one to establish the optimization of a solidification/stabilization process for steel foundry dust.     

添加CaO对燃煤重金属元素富集效果的影响

选取CaO作为吸附剂,探究了不同燃烧温度下添加CaO对重金属元素在燃煤灰渣中富集效果的影响规律。实验结果表明:添加CaO对重金属元素Cr未起到富集作用,而对Mn,Ni,Cu,Zn,As,Cd,Pb 7种重金属元素的富集效果显著;随燃烧温度的升高,CaO对各赋存形态的Mn,Ni,Cu,Zn,As的富集效果先变好而后变差,对各赋存形态的Cd和Pb的富集效果越来越好;CaO添加比(预处理后的CaO颗粒与预处理后的原煤的质量比)越大,CaO对Mn,Ni,Cu,Zn,As,Cd,Pb的富集效果越好,燃烧温度为850℃时的最佳CaO添加比为4%。     

赖氨酸废水的处理和氨回收

对赖氨酸浓废水调 p H沉淀处理后的澄清水进行预处理 :先加入石灰乳 ,搅拌、沉淀 ,SO42 -从 2 0 0 0 0 m g/ L 左右降至 130 0 mg/ L 左右 ,去除率为 94%左右 ,然后进行空气吹脱 ,NH3- N从 5 0 0 0 mg/ L左右降至 80 m g/ L左右 ,去除率 >98%。吹脱出水经厌氧生化处理后 ,再进行空气吹脱 ,NH3- N从 70 0 mg/ L 左右降至 85 mg/ L 左右 ,去除率 >86 %。再吹脱出水与稀废水混合后进行好氧生化和 A/ O、O系统处理 ,出水的 COD<10 0 m g/ L,BOD5<2 0 mg/ L,SS<70 mg/ L,NH3- N<2 5 m g/ L。对浓废水与石灰乳混合后搅拌过程中及两次空气吹脱过程中挥发的 NH3进行回收 ,将其与 H2 SO4反应 ,生成的 (NH4) 2 SO4回用于生产     

Synthesis of mesoporous silica materials from municipal solid waste incinerator bottom ash

Incinerator bottom ash contains a large amount of silica and can hence be used as a silica source for the synthesis of mesoporous silica materials. In this study, the conditions for alkaline fusion to extract silica from incinerator bottom ash were investigated, and the resulting supernatant solution was used as the silica source for synthesizing mesoporous silica materials. The physical and chemical characteristics of the mesoporous silica materials were analyzed using BET, XRD, FTIR, SEM, and solid-state NMR. The results indicated that the BET surface area and pore size distribution of the synthesized silica materials were 992 m²/g and 2–3.8 nm, respectively. The XRD patterns showed that the synthesized materials exhibited a hexagonal pore structure with a smaller order. The NMR spectra of the synthesized materials exhibited three peaks, corresponding to Q² [Si(OSi)₂(OH)₂], Q³ [Si(OSi)₃(OH)], and Q⁴ [Si(OSi)₄]. The FTIR spectra confirmed the existence of a surface hydroxyl group and the occurrence of symmetric Si–O stretching. Thus, mesoporous silica was successfully synthesized from incinerator bottom ash. Finally, the effectiveness of the synthesized silica in removing heavy metals (Pb²⁺, Cu²⁺, Cd²⁺, and Cr²⁺) from aqueous solutions was also determined. The results showed that the silica materials synthesized from incinerator bottom ash have potential for use as an adsorbent for the removal of heavy metals from aqueous solutions.