电气石对脱氯菌降解三氯乙烯的影响

以电气石作为环境微生物强化介质材料,协同以Dehalococcoides spp.为主体的脱氯混合菌群(简称脱氯菌)对水中的三氯乙烯(TCE)进行降解,探讨了电气石对降解效果的影响。实验结果表明:电气石可调节水溶液的p H使之趋向于中性并提高水溶液的电导率;在脱氯菌接种量为8%、电气石加入量为5.0 g/L的条件下降解20mg/L的TCE,84 h时TCE已全部降解,而未加电气石体系只降解了54.7%;外加电子供体甲醇和外加电气石均可明显提高脱氯菌对TCE的降解速率,且外加电气石的降解效果更好,说明电气石可能在促进微生物生长繁殖的同时也能为其提供合适的电子供体,这对降解地下水中的TCE具有重要意义。     

厌氧生物降解活性黑KN-B5

研究了在葡萄糖作为共代谢基质时活性黑KN-B5的降解效果。实验结果表明:当葡萄糖质量浓度为1 500m g/L时,活性黑KN-B5初始质量浓度为30m g/L的染料溶液厌氧生物降解24h和48h后的降解率分别达到77.5%和90.3%;活性黑KN-B5的厌氧降解符合一级动力学方程,其反应速率常数为0.043 6h-1,半衰期为15.9h;葡萄糖质量浓度的增大对提高活性黑KN-B5厌氧生物降解效果有利。紫外-可见光谱扫描结果表明,活性黑KN-B5的降解过程中生成了小分子芳香胺类化合物;扫描电子显微镜照片表明污泥中对活性黑KN-B5起降解作用的菌种主要是杆菌和球菌。     

活性艳蓝X-BR降解菌的筛选

从某印染厂废水排放出口的污泥中分离到一株活性艳蓝X-BR染料高效降解菌LPY68-14,经生理生化鉴定,该菌为埃希氏菌(Escherichia sp.).研究了影响菌株LPY68-14降解效果的因素,实验结果表明:在缺氧、质量分数为0.2%葡萄糖为外加碳源、温度37℃、接种量4 mL、pH 7的最佳条件下,质量浓度为30 mg/L的活性艳蓝X-BR经菌株LPY68-14处理24 h后的降解率可达80%;当活性艳蓝X-BR质量浓度为100～400 mg/L时,该菌处理48 h后的降解率可稳定在70%左右.     

铝碳微电解法降解水中邻苯二甲酸酯

采用铝碳微电解法降解水中邻苯二甲酸酯（PAEs）。首先考察了初始废水pH、铝碳质量比和反应时间对邻苯二甲酸二甲酯（DMP）降解率的影响，然后分别考察了超声波频率、其他金属的添加和H₂O₂加入量对铝碳微电解法降解模拟混合PAEs废水中DMP、邻苯二甲酸二乙酯（DEP）和邻苯二甲酸二丁酯（DBP）的影响。实验结果表明：在初始DMP质量浓度为20 mg/L、初始废水pH为12.0、铝碳质量比为1∶1、反应时间为30 min的条件下，DMP降解率达49.94%;在上述最佳反应条件下处理DMP，DEP，DBP的质量浓度分别为20，10，8 mg/L的模拟混合PAEs废水，当超声波频率为80 kHz时，模拟混合PAEs废水中DMP，DEP，DBP的降解率分别为63.38%，32.75%，32.23%，当铝铁质量比为100∶1时，DMP，DEP，DBP的降解率分别为59.61%，37.39%，31.50%;添加铜和H₂O₂对PAEs的降解有抑制作用。     

铁碳微电解耦合光-Fenton氧化法降解水中的十溴联苯醚

采用铁碳微电解耦合光-Fenton氧化法降解模拟废水中的十溴联苯醚(BDE-209)。探索了铁碳微电解法降解BDE-209的影响因素,考察了铁碳微电解耦合光-Fenton氧化法对BDE-209的降解效果。实验结果表明:在模拟废水BDE-209质量浓度为1 mg/L、初始废水p H为2.0、铁碳质量比为1∶1、铁粉投加量为12 g/L、微电解温度为40 oC、微电解时间为60 min的条件下,铁碳微电解法的BDE-209降解率达到82.5%;当H2O2溶液投加量为4 m L/L时,铁碳微电解耦合光-Fenton氧化法的BDE-209降解率达到95.7%。说明添加H2O2的Fenton体系对BDE-209的降解有明显促进作用。     

镰刀菌HJ01对对氯苯酚的降解特性

采用实验室分离的一株镰刀菌HJ01,以对氯苯酚(4-CP)为降解底物,以蔗糖为外加碳源,考察了蔗糖质量浓度、降解温度、初始pH对4-CP降解效果的影响,初步探讨了镰刀菌HJ01对4-CP的降解动力学和降解机理.实验结果表明:该菌株能以4-CP为惟一碳源和能源生长;在外加蔗糖为碳源,蔗糖质量浓度为3 g/L、降解温度为30℃、初始pH为8的条件下,50 mg/L4-CP能在6 d内被完全降解.以4-CP为惟一碳源和外加蔗糖下的降解动力学分别符合Haldane模型和一级动力学方程.     

两株柴油降解菌的性能研究

以0#柴油为惟一碳源,对两株柴油降解菌DS-Ⅰ菌和DS-Ⅲ菌降低液体表面张力的能力、柴油降解动力学及表面活性物质成分进行了研究。实验结果表明:DS-Ⅰ菌和DS-Ⅲ菌在生长过程中均可产生糖脂类生物表面活性物质,使发酵液表面张力降低;在11d的发酵时间内,DS-Ⅰ菌和DS-Ⅲ菌使发酵液中柴油的质量浓度从48.72m g/L分别降至16.64m g/L和9.17m g/L,柴油降解率分别为65.84%和81.18%,柴油降解速率分别为5.16m g/(L.d)和5.96m g/(L.d)。发酵液表面张力的降低与柴油的降解效果有显著的相关性。DS-Ⅲ菌在疏水性、对柴油的生长适应性和柴油降解速率等方面比DS-Ⅰ菌更好。     

一株双酚A降解菌的筛选、鉴定及其生长、降解条件

从沈阳北部污水处理厂曝气池活性污泥中驯化、分离及筛选得到一株以双酚A为唯一碳源的高效降解菌株D-17,通过菌体形态、生理生化反应特性及16S r DNA基因测序分析对其进行了鉴定,并研究了该菌株的生长及双酚A降解条件。菌种鉴定结果表明,该菌为乙酸钙不动杆菌(Acinetobacter calcoaceticus)。实验结果表明:该菌株的生长及降解双酚A的最适条件为溶液pH 7.0,接种量10%,摇床转速150 r/min,降解温度30℃,降解时间5d;当双酚A初始质量浓度为60 mg/L时,双酚A降解率达52.62%;投加蛋白胨后,双酚A降解率提高至57.15%。     

黄孢原毛平革菌的生长及降解石油条件的优化

在限氮振荡的条件下研究了藜芦醇、Tween-80、草酸、H2O2对黄孢原毛平革菌(P.C.菌)的生长量和石油降解性能的影响。实验结果表明:藜芦醇质量浓度低于0.05 g/L时促进P.C.菌的生长,高质量浓度时抑制P.C.菌的生长,石油降解率随藜芦醇质量浓度增加先升高后下降;Tween-80质量浓度低于7 mg/L时,P.C.菌生长量和石油降解率均随Tween-80质量浓度增大而增加,Tween-80质量浓度大于其临界胶束浓度时,P.C.菌生长量和石油降解率均低于未加Tween-80时;添加草酸抑制P.C.菌的生长,草酸质量浓度为35 mg/L时石油降解率最高,草酸质量浓度为350 mg/L时石油降解率低于未加草酸时;加入H2O2的体系中,石油降解率明显高于无H2O2体系。     

TiO2纳米管光电催化降解酸性橙染料

采用电化学阳极氧化法在金属钛表面制备锐钛矿型TiO2纳米管,并以TiO2纳米管薄膜为阳极,考察溶液pH、外加偏压以及NaC1浓度对酸性橙的光电催化降解反应的影响.实验结果表明:在溶液pH为3.0、外加偏压为2.5V、NaCl浓度为0.05 mol/L的最佳实验条件下反应30 min,酸性橙降解率可达99.99％;TiO2纳米管重复使用25次,酸性橙降解率仍可达94.57％.     

Microbiological degradation of phenol using mixed liquors of Pseudomonas putida and activated sludge

This work investigated the biodegradation potential of phenol using mixed liquors of Pseudomonas putida (ATCC 31800) and activated sludge. Experiments were made as a function of solution pH (6-10), temperature (30-36 degrees C), nitrogen source (NH4)2SO4 (0.5-0.8 g/l), and carbon source glucose (0.5-0.8 g/l). Response surface methodology by the Box-Behnken model was used to examine the role of four process factors on phenol degradation. It was shown that a second-order polynomial regression model could properly interpret the experimental data with an R2-value of 0.9997 and an F-value of 3605.45, based on which the maximum degradation of phenol was estimated up to 80.1% within the range examined. Interactions between process parameters and each significance effect on phenol degradation were also discussed.     

Biodegradation of Coproducts from Industrially Processed Corn in a Compost Environment

Information pertaining to biodegradability of renewable polymeric material is critical for the design and development of single-use biodegradable consumer products. The rate and extent of biodegradation of corn fiber, corn zein, cornstarch, distillers grain, and corn gluten meal were evaluated in compost environments under variable temperature, pH, and moisture conditions. Generally, composts with higher temperature (40°C), neutral pH (7.0), and 50%–60% moisture appeared to be ideal for corn coproduct biodegradation, particularly for corn gluten meal and corn zein. Low moisture conditions slowed biodegradation considerably, but degradation rates improved when moisture content increased up to 60%. Thereafter, increased moisture particularly slowed the degradation of corn gluten meal and corn zein, whereas cornstarch degradation remained unaffected. At low pH (4.0) and high pH (11.0) the rate of degradation of most coproducts was slowed somewhat. Cornstarch degradation was slower at pH 7.0, but degradation improved with increased temperatures. Increase in compost temperature from 25 to 40°C (in 5°C increments) also improved biodegradation of corn fiber and distillers grain. Addition of 1% urea to compost as a nitrogen source decreased the extent of biodegradation nearly 40% for corn gluten meal and corn zein, and 20% for cornstarch samples. Treatment of compost with 0.02% azide inhibited biodegradation of all coproducts, suggesting that the presence of metabolically active microbial cells is required for effective degradation of biobased materials in a compost environment.     

2,5-二氟硝基苯的厌氧降解特性

考察了2,5-二氟硝基苯(2,5-DFNB)的厌氧降解特性及F~-对其厌氧降解过程的影响。实验结果表明:当初始2,5-DFNB质量浓度为5~100 mg/L时,随着降解时间的延长,2,5-DFNB对厌氧消化产甲烷的抑制效应逐渐减弱直至消失;在厌氧降解过程中,2,5-DFNB的降解基本无延滞期,但仅发生了硝基转化,并未实现还原脱氟;2,5-DFNB的厌氧降解动力学符合Andrews模型,最大比降解速率、底物饱和常数、底物抑制常数分别为5.9 mg/(g·h),67.7 mg/L,1 299.6 mg/L;质量浓度为10~80 mg/L的F~-对2,5-DFNB厌氧降解过程影响甚小,而质量浓度大于100 mg/L时则产生了较严重的抑制作用。     

微波催化氧化法处理甲基橙废水

采用微波催化氧化法处理模拟甲基橙废水,考察了微波功率、辐射时间、H2O2用量、活性炭用量对甲基橙去除率的影响。在微波功率630w、辐射时间9min、H2O2用量10mL／L,活性炭用量10g／L的条件下,甲基橙的去除率达到90％左右,并对实际染料废水、炼焦废水、炼油废水、餐饮废水进行了处理,取得了满意的结果。     

可见光催化剂BiVO_4 降解废水中直接耐酸大红4BS

以直接耐酸大红4BS模拟染料废水为目标污染物,研究了BiVO_4对直接耐酸大红4BS(简称4BS)的吸附效果以及废水初始质量浓度、废水pH和BiVO_4的加入量对光催化降解效果的影响.实验结果表明:当废水初始质量浓度为40 mg/L、废水pH为6.38、BiVO_4加入量为1.0 g/L时,4BS的降解率可达98.9%;BiVO_4重复使用5次后4BS的降解率可达80.0%以上;COD的变化趋势说明4BS被催化剂吸附和光催化降解的过程是循序渐进的.     

三维电极电Fenton氧化法处理染料废水

采用三维电极电Fenton氧化法处理实际染料废水,探究了染料废水处理效果的影响因素。实验结果表明：以钌铱镀层钛电极为阳极、不锈钢板为阴极、粉末活性炭为颗粒电极,在粉末活性炭投加量为2.0 g/L、电流密度为0.5 mA/mm²、极板间距为3 cm、pH为2.0、硫酸亚铁投加量为0.50 g/L的最优工艺条件下,反应2 h后COD、TOC、氨氮、色度的去除率达到最大,分别为62.80%、41.15%、42.48%和95.00%;粉末活性炭作为颗粒电极可使染料废水COD去除率提高18个百分点;重复使用10次的处理效果与第2次基本持平。     

微生物降解重油的初步研究

丛石油污染的土壤中筛选出一株假单胞菌,考察了其对重油的降解效果。降解18d,重油的降解率达到42．8％,饱和烃、芳香烃、胶质、沥青质的降解率分别为42．95％,43．85％,44．5％,5．55％;质量浓度2．5g／L的表面活性剂Tween-80可使重油的18d降解率达到51．0％;弱碱性条件有利于重油的生物降解;生物泥浆法处理重油污染的土壤,1kg土壤中重油质量100g,降解45d,重油的降解率达到38．85％。     

Biodegradation of Coir and Sisal Applied in the Automotive Industry

This paper discusses the results of biodegradability tests of natural fibers used by the automotive industry, namely: coir, coir with latex, and sisal. The biodegradation of coir, coir with latex, and of sisal fibers was determined by monitoring the production of carbon dioxide (CO₂) (IBAMA—E.1.1.2, 1988) and fungal growth (DIN 53739, 1984). The contents of total extractives, lignin, holocellulose, ashes, carbon, nitrogen and hydrogen of the fibers under study were determined in order to ascertain their actual content and to understand the results of the biodegradation tests. The production of CO₂ indicated low biodegradation, i.e., about 10% in mass, for all the materials after 45 days of testing; in other words, no material inhibited glucose degradation. However, the percentage of sisal fiber degradation was fourfold higher than that of coir with latex in the same period of aging. The fungal growth test showed a higher growth rate on sisal fibers, followed by coir without latex. In the case of coir with latex, we believe the fungal growth was not intense, because natural latex produces a bactericide or fungicide for its preservation during bleeding [1]. An evaluation of the materials after 90 days of aging tests revealed breaking of the fibers, particularly sisal and coir without latex, indicating fungal attack and biodegradation processes.     

催化臭氧氧化法处理抗生素废水生化出水

以负载不同金属的硅胶为催化剂,采用催化臭氧氧化法处理抗生素废水生化出水,并对催化剂投加量、反应时间等反应条件进行了优化。实验结果表明：铁/硅胶催化剂效果最好;在铁/硅胶催化剂投加量为0.33 g/L、反应时间为1 h的条件下处理COD为954.7 mg/L、BOD₅为66.8 mg/L、ρ（氨氮）为98 mg/L的抗生素废水生化出水,COD去除率为54.9%,氨氮去除率为44.4%,BOD₅/COD由0.07提高至0.20。