Modelling of moisture-dependent aerobic degradation of solid waste

In landfill, high temperature levels come from aerobic reactions inside the waste surface layer. They are known to make anaerobic processes more reliable, by partial removal of easily biodegradable substrates. Aerobic biodegradation of the main components of biodegradable matter (paper and cardboard waste, food and yard waste) is considered. In this paper, two models which take into account the effect of moisture on aerobic biodegradation kinetics are discussed. The first one (Model A) is a simple, first order, substrate-related model, which assumes that substrate hydrolysis is the limiting step of the process. The second one (Model B) is a biomass-dependant model, considering biological growth processes. Respirometric experiments were performed in order to evaluate the efficiency of each model. The biological oxygen demands of shredded paper and cardboard samples and of food and yard waste samples prepared at various initial water contents were measured. These experimental data were used to identify model parameters. Model A, which includes moisture dependency on the maximum amount of biodegraded matter, is relevant for paper and cardboard biodegradation. On the other hand, Model B, including moisture effect on the growth rate of biomass is suitable to describe food and yard waste biodegradation.     

Selective organic compounds degradation under controlling composting conditions

Organic matter stabilization resulted from the decrease of cellulose, xylan, arabinan, acetyl groups, glucuronic acids, galacturonic acids (easily biodegradable fractions) and the increase of lignin (resistant compound) and humic substances coming from the initial wastes have been studied. A central composite experimental design was used to investigate the influence of environmental composting parameters (moisture, aeration and particle size) on organic matter evolution. The organic matter evolution was clearly influenced by the studied composting parameters. All results were concordant, with an increase of humic substances and lignin and a decrease of the rest of the cellulose and hemicellulose compounds. Lower cellulose, xylan, acetyl groups and glucuronic acids contents (higher degradation) have been observed under low particle size (1 cm) and higher moisture content (70%). However lower lignin and higher humic substances under medium (3 cm) to low particle size and low moisture content (40%) have been found.     

Characteristics of municipal solid waste and sewage sludge co-composting

The purpose of this work is to study the characteristics of the co-composting of municipal solid waste (MSW) and sewage sludge (SS). Four main influencing factors (aeration pattern, proportion of MSW and SS, aeration rate and mature compost (MC) recycling) were systematically investigated through changes of temperature, oxygen consumption rate, organic matters, moisture content, carbon, nitrogen, carbon-to-nitrogen ratio, nitrogen loss, sulphur and hydrogen. We found that a continuous aeration pattern during composting was superior to an intermittent aeration pattern, since the latter delayed the composting process. A 3:1 (v:v) mixture of MSW and SS was most beneficial to composting. It maintained the highest temperature for the longest duration and achieved the fastest organic matter degradation and highest N content in the final composting product. A 0.5L/minkgVS aeration rate best ensured rapid initiation and maintained moderate moisture content for microorganisms. After the mature MC was recycled to the fresh materials as a bulking agent, the structure and moisture of the initial materials were improved. A higher proportion of MC resulted in quicker decrease of the temperature, oxygen consumption rate and moisture. Therefore a 3:1:1 (v:v:v) proportion of MSW: SS: MC is recommended.     

Enhanced Mineralization of PLA Meltblown Materials Due to Plasticization

Polylactic acid (PLA) is one of the important biodegradable polymers. It is widely used in many industrial applications such as films and fibers. Its biodegradability is based on data derived mostly from composting processes. For a broad application of the PLA material in personal care products, an understanding of anaerobic biodegradability is essential because soiled personal care products are usually disposed of in sanitary landfills, where biodegradability mechanisms are predominately in anaerobic conditions. Extensive laboratory results are acquired to elucidate the effects of the temperature on the PLA anaerobic sludge biodegradation. When the temperature is higher than PLA glass transition temperature (T_g), anaerobic degradation is accelerated. A plausible mechanism to explain this observation is that amorphous part of the polymer is easily accessible by microorganisms. When the degrading temperature is below PLA glass transition temperature, sample mineralization under anaerobic conditions is apparently slowed. The mechanisms elucidated by T_g modification can be utilized to control the rate of PLA biodegradation for sustainable waste management.     

A kinetic analysis of solid waste composting at optimal conditions

This discussion explores the possibility of having a measure of the biodegradable organic carbon content in solid wastes. Currently, indirect measures for determining the concentration of biodegradable organic matter are being used and most of them are based on respiration indices (oxygen consumption or carbon dioxide production) or chemical parameters (volatile solids or total organic carbon). The results obtained for the cumulative carbon dioxide production in composting experiments can be expressed as "aerobic biodegradable carbon" for the wastes that were studied. The calculation of a useful biodegradable C/N can also be obtained from the aerobic biodegradable carbon content. A comparison with some results obtained in measuring the concentration of "anaerobic biodegradable carbon" also is presented.     

Evaluation of laboratory-scale in-vessel co-composting of tobacco and apple waste

Efficient composting process requires set of adequate parameters among which physical–chemical properties of the composting substrate play the key-role. Combining different types of biodegradable solid waste it is possible to obtain a substrate eligible to microorganisms in the composting process. In this work the composting of apple and tobacco solid waste mixture (1:7, dry weight) was explored. The aim of the work was to investigate an efficiency of biodegradation of the given mixture and to characterize incurred raw compost. Composting was conducted in 24 L thermally insulated column reactor at airflow rate of 1.1 L min^?1. During 22 days several parameters were closely monitored: temperature and mass of the substrate, volatile solids content, C/N ratio and pH-value of the mixture and oxygen consumption. The composting of the apple and tobacco waste resulted with high degradation of the volatile solids (53.1%). During the experiment 1.76 kg of oxygen was consumed and the C/N ratio of the product was 11.6. The obtained temperature curve was almost a “mirror image” of the oxygen concentration curve while the peak values of the temperature were occurred 9.5 h after the peak oxygen consumption.     

Characterization and modelling of the heat transfers in a pilot-scale reactor during composting under forced aeration

The paper focused on the modelling of the heat transfers during composting in a pilot-scale reactor under forced aeration. The model took into account the heat production and the transfers by evaporation, convection between material and gas crossing the material, conduction and surface convection between gas and material in bottom and upper parts of the reactor. The model was adjusted thanks to the measurements practised during fifteen composting experiments in which five organic wastes were, each, composted under three constant aeration rates. Heat production was considered proportional to oxygen consumption rate and the enthalpy per mole oxygen consumed was assumed constant. The convective heat transfer coefficients were determined on basis of the continuous measurements of the temperatures of both the lid and the bottom part of the reactor. The model allowed a satisfying prediction of the temperature of the composting material. In most cases, the mean absolute discard between the experimental and the simulated temperatures was inferior to 2.5°C and the peaks of temperature occurred with less than 8h delay. For the half of the experiments the temperature discard between the simulated peak and the experimental one was inferior to 5°C. On basis of the calculation of a stoichiometric production of water through oxidation of the biodegradable organic matter, the simulation of water going out from material as vapour also allowed a rather satisfying prediction of the mass of water in final mixture. The influence of the aeration rate on every type of heat loss was characterized. Finally, the model was used to evaluate the impacts on material temperature caused by the change of the insulation thickness, the ambient temperature, take the lid away, the increase or the decrease of the mass of waste to compost.     

Maturity assessment of compost from municipal solid waste through the study of enzyme activities and water-soluble fractions

In this work the dynamics of biochemical (enzymatic activities) and chemical (water-soluble fraction) parameters during 100 days of municipal solid wastes composting were studied to evaluate their suitability as tools for compost characterization. The hydrolase (protease, urease, cellulase, beta-glucosidase) and dehydrogenase activities were characterized by significant changes during the first 2 weeks of composting, because of the increase of easily decomposable organic compounds. After the 4th week a "maturation phase" was identified in which the enzymatic activities tended to gently decrease, suggesting the stabilisation of organic matter. Also the water-soluble fractions (water-soluble carbon, nitrogen, carbohydrates and phenols), which are involved in many degradation processes, showed major fluctuations during the first month of composting. The results obtained showed that the hydrolytic activities and the water-soluble fractions did not vary statistically during the last month of composting. Significant correlations between the enzymatic activities, as well as between enzyme activities and water-soluble fractions, were also highlighted. These results highlight the suitability of both enzymatic activities and water soluble fractions as suitable indicators of the state and evolution of the organic matter during composting. However, since in the literature the amount of each activity or fraction at the end of composting depends on the raw material used for composting, single point determinations appear inadequate for compost characterization. This emphasizes the importance of the characterization of the dynamics of enzymatic activities and water-soluble fractions during the process.     

Biodegradability and biodegradation rate of poly(caprolactone)-starch blend and poly(butylene succinate) biodegradable polymer under aerobic and anaerobic environment

The biodegradability and the biodegradation rate of two kinds biodegradable polymers; poly(caprolactone) (PCL)-starch blend and poly(butylene succinate) (PBS), were investigated under both aerobic and anaerobic conditions. PCL-starch blend was easily degraded, with 88% biodegradability in 44 days under aerobic conditions, and showed a biodegradation rate of 0.07 day⁻¹, whereas the biodegradability of PBS was only 31% in 80 days under the same conditions, with a biodegradation rate of 0.01 day⁻¹. Anaerobic bacteria degraded well PCL-starch blend (i.e., 83% biodegradability for 139 days); however, its biodegradation rate was relatively slow (6.1 mL CH₄/g-VS day) compared to that of cellulose (13.5 mL CH₄/g-VS day), which was used as a reference material. The PBS was barely degraded under anaerobic conditions, with only 2% biodegradability in 100 days. These results were consistent with the visual changes and FE-SEM images of the two biodegradable polymers after the landfill burial test, showing that only PCL-starch blend had various sized pinholes on the surface due to attack by microorganisms. This result may be use in deciding suitable final disposal approaches of different types of biodegradable polymers in the future.     

Influence of aeration rate on nitrogen dynamics during composting

The paper aimed to study the influence of aeration rate on nitrogen dynamics during composting of wastewater sludge with wood chips. Wastewater sludge was sampled at a pig slaughterhouse 24h before each composting experiment, and mixtures were made at the same mass ratio. Six composting experiments were performed in a lab reactor (300 L) under forced aeration. Aeration flow was constant throughout the experiment and aeration rates applied ranged between 1.69 and 16.63 L/h/kg DM of mixture. Material temperature and oxygen consumption were monitored continuously. Nitrogen losses in leachates as organic and total ammoniacal nitrogen, nitrite and nitrate, and losses in exhaust gases as ammonia were measured daily. Concentrations of total carbon and nitrogen i.e., organic nitrogen, total ammoniacal nitrogen, and nitrite and nitrate were measured in the initial substrates and in the composted materials. The results showed that organic nitrogen, which was released as NH4+/NH3 by ammonification, was closely correlated to the ratio of carbon removed from the material to TC/N(org) of the initial substrates. The increase of aeration was responsible for the increase in ammonia emissions and for the decrease in nitrogen losses through leaching. At high aeration rates, losses of nitrogen in leachates and as ammonia in exhaust gases accounted for 90-99% of the nitrogen removed from the material. At low aeration rates, those accounted for 47-85% of the nitrogen removed from the material. The highest concentrations of total ammoniacal nitrogen in composts occurred at the lowest aeration rate. Due to the correlation of ammonification with biodegradation and to the measurements of losses in leachates and in exhaust gases, the pool NH4+/NH3 in the composting material was calculated as a function of time. The nitrification rate was found to be proportional to the mean content of NH4+/NH3 in the material, i.e., initial NH4+/NH3 plus NH4+/NH3 released by ammonification minus losses in leachates and in exhaust gases. The aeration rate was shown to be a main parameter affecting nitrogen dynamics during composting since it controlled the ammonification, the ammonia emission and the nitrification processes.     

Oxygen demand for the stabilization of the organic fraction of municipal solid waste in passively aerated bioreactors

Conventional aerobic waste treatment technologies require the use of aeration devices that actively transport air through the stabilized waste mass, which greatly increases operating costs. In addition, improperly operated active aeration systems, may have the adverse effect of cooling the stabilized biomass. Because active aeration can be a limiting factor for the stabilization process, passive aeration can be equally effective and less expensive. Unfortunately, there are few reports documenting the use of passive aeration systems in municipal waste stabilization. There have been doubts raised as to whether a passive aeration system provides enough oxygen to the organic matter mineralization processes. In this paper, the effectiveness of aeration during aerobic stabilization of four different organic fractions of municipal waste in a reactor with an integrated passive ventilation system and leachate recirculation was analyzed. For the study, four fractions separated by a rotary screen were chosen. Despite the high temperatures in the reactor, the air flow rate was below 0.016 m³/h. Using Darcy’s equation, theoretical values of the air flow rate were estimated, depending on the intensity of microbial metabolism and the amount of oxygen required for the oxidation of organic compounds. Calculations showed that the volume of supplied air exceeded the microorganisms demand for oxidation and endogenous activity by 1.7–2.88-fold.     

Feasibility study of a passive aeration reactor equipped with vertical pipes for compost stabilization of cow manure.

Pilot-scale composting was carried out with cow manure to evaluate the performances of two passive aeration systems: a conventional passive aeration system equipped with horizontal pipes and an unusual passive aeration method based on air delivery by means of vertical pipes. The effects of both types of passive aeration apparatus were investigated in order to determine the degree of composting rate by continuously monitoring temperature, moisture content, organic matter, electrical conductivity, pH and C/N ratio in the piles. Temperatures in the range of thermophily (55-65 degrees C) were reached in all runs within 1-2 days then lasting for about 1 week, a span long enough for pathogen abatement. Results suggest that passive aeration carried out by vertical pipes is more effective for air delivery into compost piles than conventional passive aeration of air adduction with horizontal pipes. The variation in the number of vertical pipes was revealed to be an important parameter for the control of composting rate and temperature. Composting rates estimated from the heat balance equation were substantially in agreement with those computed through the conversion ratio of total organic matter decrement. The conversion ratios and composting rates obtained in this study using passive aeration with vertical pipes were well aligned with those found using forced air delivery systems.     

A complete mass balance of a complex combined anaerobic/aerobic municipal source-separated waste treatment plant

In this study a combined anaerobic/aerobic full-scale treatment plant designed for the treatment of the source-separated organic fraction of municipal solid waste (OFMSW) was monitored over a period of one year. During this period, full information was collected about the waste input material, the biogas production, the main rejects and the compost characteristics. The plant includes mechanical pre-treatment, dry thermophilic anaerobic digestion, tunnel composting system and a curing phase to produce compost. To perform the monitoring of the entire plant and the individual steps, traditional chemical methods were used but they present important limitations in determining the critical points and the efficiency of the stabilization of the organic matter. Respiration indices (dynamic and cumulative) allowed for the quantitative calculation of the efficiency of each treatment unit. The mass balance was calculated and expressed in terms of Mgy(-1) of wet (total) matter, carbon, nitrogen and phosphorus. Results show that during the pre-treatment step about 32% of the initial wet matter is rejected without any treatment. This also reduces the biodegradability of the organic matter that continues to the treatment process. About 50% of the initial nitrogen and 86.4% of the initial phosphorus are found in the final compost. The final compost also achieves a high level of stabilization with a dynamic respiration index of 0.3±0.1g O(2) per kg of total solids per hour, which implies a reduction of 93% from that of the raw OFMSW, without considering the losses of biodegradable organic matter in the refuse (32% of the total input). The anaerobic digestion process is the main contributor to this stabilization.     

Aerobic Biodegradation of Polymers in Solid-State Conditions: A Review of Environmental and Physicochemical Parameter Settings in Laboratory Simulations

During the last few years, biodegradable polymers have been developed to replace petrochemical polymers. Until now, research devoted to these polymers essentially focused on their biodegradability. There is now a need to bear out their nontoxicity. To verify this, the biodegradation must be carried out in accelerated laboratory tests which allow the metabolites and residues to be recovered. To reproduce the natural conditions (compost, field) as closely as possible, degradation experiments must be run on solid-state substrates. We review studies of aerobic degradation in solid-state substrates. This article focuses in particular on the environmental, physical, and chemical parameters (such as substrate nature, moisture, temperature, C/N ratio, and pH) that influence biodegradation kinetics. This study also aims at finding the solid substrate most adapted to residues and metabolite recovery. The most significant parameters would appear to be the substrate type, moisture content, and temperature. Inert substrates such as vermiculite are well suited to residue extraction. This review also opens the field to new research aimed at optimizing conditions for aerobic solid-state biodegradation and at recovering the metabolites and residues of this degradation process.     

A kinetic analysis of solid waste composting at optimal conditions

Six municipal solid waste (MSW) and yard waste components (food waste, mixed paper, yard waste, leaves, branches, grass clippings) were aerobically decomposed to measure the extent of decomposition under near optimal conditions. Decomposition was characterized by at least two principal stages, for most components, as was indicated by the carbon dioxide production rates. An aerobic biodegradation conceptual model is presented here based on the principle that solids hydrolysis is the rate-limiting step during solid waste composting. The mineralizable solid carbon of each solid waste component was assumed to comprise the readily, the moderately and the slowly (or refractory) hydrolysable carbons, each hydrolyzing at different rates to aqueous (water soluble) carbon. Aqueous carbon mineralizes to CO2 at rapid rates that are not rate-limiting to the process. Solids hydrolysis rate constants were calculated after fitting the experimentally determined carbon dioxide production rate data to model results. Hydrolysis rates for the readily hydrolysable carbon in all components ranged from approximately 0.06 to 0.1 d(-1); hydrolysis rates for the moderately hydrolysable carbon ranged from 0.005 to 0.06 d(-1). Leaves, branches and grass clippings did not have a readily hydrolysable carbon fraction, whilst the leaves and branches had the largest slowly hydrolysable carbon fractions (70%, 82%, respectively, of the total solid organic carbon). Grass and yard waste did not contain slowly hydrolysable carbon fractions. Food waste had the largest readily hydrolysable carbon fraction and produced the highest amount of CO2 among all substrates. Moderately hydrolysable solid carbon fractions ranged from 16% to 90% of the total solid organic carbon for all substrates used.     

Influence of oxygen flow rate on reaction rate of organic matter in leachate from aerated waste layer containing mainly incineration ash

It is known that aeration reduces rapidly the concentration of organic matter in leachate. However, the oxygen flow rate required to attain a certain reaction rate of organic matter should be carefully estimated. In this study, using the oxygen ratio (the ratio of oxygen flow rate by aeration to oxygen consumption rate of waste layer) as a parameter, the reaction rate of organic matter in leachate from landfilled incineration ash and incombustible waste upon aeration was evaluated. Total organic carbon (TOC) in the leachate was reduced rapidly when the oxygen ratio was high. The decomposition rate exceeded the elution rate of TOC in the leachate from the waste layer for several days when the oxygen ratio was above 10². The results indicate that the oxygen ratio can be used as a parameter for the aeration operation in actual landfill sites, to rapidly stabilize organic matter in leachate.     

Change of the chemical composition and biodegradability of the Van Soest soluble fraction during composting: A study using a novel extraction method

Van Soest fractionation is widely employed to characterize exogenous organic matter. The soluble fraction of Van Soest fractionation (SOL, extracted using hot water and then neutral detergent) often increases in line with compost maturity, although it is generally considered as labile. We have developed an alternative extraction method that comprises four successive steps (extraction using hot water, sodium tetraborate, dichloromethane/methanol and chelating resin) in order to clarify the chemical nature of the SOL fraction and explain its biodegradability. This method was tested on municipal solid waste compost sampled during the thermophilic phase (MSWi) and after 8 months of composting (MSWm). Both methods extracted similar proportions of organic matter. The composition of the residues was similar in MSWm although differences were noted for the extraction of polysaccharides and lipids in the case of MSWi. The hot water extractable fraction decreased during composting. Its high biodegradability in MSWi was linked to the high polysaccharide content revealed by pyrolysis–GC/MS and FTIR spectroscopy. The increase in the sodium tetraborate extractable fraction mainly explained the increase in the SOL fraction during composting. This was made up of N-containing compounds, polysaccharides and lipids in the immature compost, and a majority of N-containing compounds in the mature compost. During composting, the stabilization of organic matter in the SOL fraction extractable by sodium tetraborate and EDTA might principally involve N-containing structures through the formation of complexes of organic matter with metal ions, especially Ca²⁺, which may be broken down during extraction of the Van Soest soluble fraction. These mechanisms still need to be investigated.     

Modelling of organic matter dynamics during the composting process

Composting urban organic wastes enables the recycling of their organic fraction in agriculture. The objective of this new composting model was to gain a clearer understanding of the dynamics of organic fractions during composting and to predict the final quality of composts. Organic matter was split into different compartments according to its degradability. The nature and size of these compartments were studied using a biochemical fractionation method. The evolution of each compartment and the microbial biomass were simulated, as was the total organic carbon loss corresponding to organic carbon mineralisation into CO₂. Twelve composting experiments from different feedstocks were used to calibrate and validate our model. We obtained a unique set of estimated parameters. Good agreement was achieved between the simulated and experimental results that described the evolution of different organic fractions, with the exception of some compost because of a poor simulation of the cellulosic and soluble pools. The degradation rate of the cellulosic fraction appeared to be highly variable and dependent on the origin of the feedstocks. The initial soluble fraction could contain some degradable and recalcitrant elements that are not easily accessible experimentally.     

Critical Review of Norms and Standards for Biodegradable Agricultural Plastics Part II: Composting

The critical review of norms and standards and corresponding tests to determine the compostability of biodegradable plastics, possibly applicable also to biodegradable agricultural plastics, shows that many norms concerning testing and labelling of compostable plastics have been established at the international level. Some of them are about plastic materials, some others are about products like packaging. The media and conditions of testing cover mainly the conditions designed for industrial composting facilities, and only a few concern home composting conditions. Considering that the end of life management of biodegradable agricultural plastic products will be done at the farm to reduce the management of the waste and also its cost, only a few of these norms are considered to be suitable for adaptation to cover also biodegradable agricultural plastic products. The biodegradability validation criteria under composting conditions, such as the threshold percentage of biodegradation and disintegration, the time and temperature, and the ecotoxicity, are presented for the main norms and standard testing methods. Based on these different norms and their content, a list of specs and technical requirements that could be adapted to meet farm composting conditions for agricultural compostable plastics is proposed. These requirements may be used as criteria for the establishment of a new integrative norm for agricultural compostable plastics.     

Combining chemical sequential extractions with 3D fluorescence spectroscopy to characterize sludge organic matter

The design and management of anaerobic digestion of sewage sludge (SS) require a relevant characterisation of the sludge organic matter (OM). Methods currently used are time-consuming and often insufficiently informative. A new method combining chemical sequential extractions (CSE) with 3D fluorescence spectroscopy was developed to provide a relevant SS characterisation to assess both OM bioaccessibility and complexity which govern SS biodegradability. CSE fractionates the sludge OM into 5 compartments of decreasing accessibility. First applied on three SS samples with different OM stability, fractionation profiles obtained were in accordance with the latter. 3D fluorescence spectroscopy revealed that the bioaccessible compartments were mainly constituted of simple and easily biodegradable OM while the unaccessible ones were largely made of complex and refractory OM. Then, primary, secondary and anaerobically digested sludge with different biodegradabilities were tested. Complexity revealed by 3D fluorescence spectroscopy was linked with biodegradability and chemical accessibility was correlated with sludge bioaccessibility.