Al-SiO2介孔材料吸附电解锰废水中的锰、铬离子

以不同n (Al )1 n (SiO 2 )的Al -SiO 2 介孔材料为吸附剂处理电解锰废水,并利用中卜组合设计法研究电解锰废水中锰离子与铬离子(包括铬(!和铬(")的相互作用对材料吸附性能的影响.实验结果表明:以n (Al )1 n (SiO 2 )为1:1 的Al -SiO 2 介孔材料为吸附剂,当吸附剂加入量...     

无黏结剂ZSM-5分子筛的制备及其对甲苯的吸附性能

以硅溶胶为黏结剂，将粗孔硅胶、聚乙二醇、拟薄水铝石、ZSM-5晶种导向剂捏条成型，采用干胶转化法制备得到了无黏结剂ZSM-5分子筛。XRD和SEM等表征方法的结果显示，采用干胶转化法制备得到的ZSM-5分子筛的相对结晶度较高，具有200nm左右的小晶粒构成的自支撑结构。采用无黏结剂ZSM-5分子筛吸附剂进行甲苯吸附-脱附实验，该吸附剂表现出良好的吸附性能，对甲苯的脱附性能优于活性炭。     

交联壳聚糖/沸石复合吸附剂的制备及性能

用沸石负载由缩水甘油基三乙基氯化铵交联的壳聚糖，制得了性能良好的交联壳聚糖/沸石复合吸附剂。研究了该吸附剂应用性能的影响因素，探讨了该吸附剂的吸附性、沉降性和重复使用性，利用FTIR仪和高倍透射电子显微镜对该吸附剂的结构进行了表征。实验结果表明:壳聚糖的交联度为0.93、交联壳聚糖与沸石的质量比为0.045时，制得的交联壳聚糖/沸石复合吸附剂对腐殖酸的去除率可达81.4%，吸附量为4.07mg/g;交联壳聚糖/沸石复合吸附剂对腐殖酸的吸附性能较沸石有显著提高，沉降时间较交联壳聚糖明显缩短;经二次洗脱后腐殖酸去除率仍可达80.2%，腐殖酸吸附量为4.01mg/g。     

活性炭对气体中二硫化碳吸附性能的研究

研究了４种不同活性炭的孔结构及对二硫化碳的平衡吸附性能,并对４种活性炭床层的穿透性进行了考察,为选择吸附净化废气中低浓度二硫化碳的吸附剂奠定了基础。     

活化后钾改性正硅酸锂吸附CO2的性能评价及动力学研究

制备了钾改性正硅酸锂(K-Li4SiO4),并对其进行了自活化,考察了活化后K-Li4SiO4吸附剂在不同温度和CO2浓度气氛中吸附CO2的性能及动力学行为。总体而言,吸附剂的CO2吸附能力随着温度的升高、CO2浓度的增加而提升。在700℃、100%体积分数CO2气氛中吸附剂的吸附量最大,可达7.9 mmol/g,吸附剂的利用率为95.2%。利用双指数模型能够很好地描述吸附剂在各个温度以及各个CO2浓度气氛下的CO2吸附过程。吸附活化能随着CO2气氛浓度的升高而降低,CO2体积分数为20%,50%,100%时的吸附活化能分别为26448,14035,6178 J/mol。     

硅胶固载季鏻离子液体对CO_2的吸附

采用嫁接法制备了硅胶固载季鏻双三氟甲烷磺酰亚胺盐离子液体,并将其用于对CO2的吸附,考察了吸附剂的吸附等温线及循环使用性,并运用均相表面扩散模型(HSDM)研究了吸附动力学。采用FTIR和TG等技术对试样进行了表征。表征结果显示:离子液体已成功固载到硅胶上;煅烧活化硅胶对季鏻离子液体(C-Si O2-P4T)的固载量为5.39%(w);固载试样基本保持了硅胶的孔道特征。实验结果表明:C-Si O2-P4T具有较高的CO2平衡吸附量,且能显著提高CO2/N2吸附选择性,循环使用6次仍保持良好的吸附能力;HSDM可较好地拟合CO2在C-Si O2-P4T内的扩散行为,40℃下的扩散系数在10-7 m2/s数量级,与硅胶同级,优于纯季鏻离子液体。     

沸石和糠醛渣对硝酸盐吸附性影响的研究

利用沸石和糠醛渣改性制得硝酸盐吸附剂,研究吸附剂的饱和吸附能力和各种影响因子(温度、pH值、吸附时间、吸附质浓度、吸附剂用量和干扰离子)对硝酸盐吸附性能的影响。结果表明,改性沸石和糠醛渣的硝酸盐吸附能力大大增强;影响因子对吸附剂吸附硝酸盐能力的影响很大,其中升温有利于解吸、在中性pH值附近脱除率较高、干扰离子可降低吸附剂的硝酸盐脱除率;影响因子对改性糠醛渣MF的吸附影响要比对改性沸石的影响大。因此,改性沸石在实际应用中比改性糠醛渣MF的硝酸盐吸附能力强,具有更好的应用前景。     

碱熔融—微波晶化法合成粉煤灰沸石及其对Cd2+的吸附

以粉煤灰为主要原料，采用碱熔融—微波晶化法合成粉煤灰沸石。采用XRD，SEM，TEM等技术表征了粉煤灰沸石的微观结构，并对其吸附Cd²⁺的性能进行了研究。表征结果显示，粉煤灰沸石主要由X型沸石、P型沸石和铝组成，粉煤灰沸石中有排列规则、呈蜂窝状的孔穴和孔道存在，其孔穴和孔道大小分布均匀，致密。粉煤灰沸石的比表面积为108.49 m²/g，平均孔径为3.779 nm，孔体积为0.221 mL/g。实验结果表明，在溶液pH为7、吸附时间30 min的最佳吸附条件下，Cd²⁺去除率均大于94%。粉煤灰沸石对Cd²⁺的吸附可很好地用二级动力学方程进行拟合，相关系数为0.999 99。可用Langmuir等温吸附模型描述该吸附过程，该吸附过程是单分子层吸附，主要是化学吸附，粉煤灰沸石对Cd²⁺的饱和吸附量为49.261 mg/g。     

氯化锌活化法制备甘蔗渣活性炭吸附剂

采用氯化锌活化法制备了甘蔗渣活性炭吸附剂，并考察了活化剂氯化锌溶液浓度、活化温度和活化时间对吸附剂吸附性能的影响。实验结果表明，氯化锌活化法制备甘蔗渣活性炭吸附剂的最佳工艺条件为：活化温度800℃、氯化锌溶液质量浓度190g／L、活化时间60min。所得甘蔗渣活性炭吸附剂的得率为30．3％，碘吸附值为1070mg／g，亚甲基蓝吸附值（以0．1g吸附剂吸附的亚甲基蓝体积计）为15．0mL，达到了GB／T13803．2—1999《木质净水用活性炭》一级品标准（碘吸附值1000mg／g，亚甲基蓝吸附值9mL）。     

金属有机骨架材料Cu2(BTC)3对CO2的吸附

采用溶剂热法,以均苯三甲酸(H3BTC)为有机配体与硝酸铜进行反应合成了Cu2(BTC).通过XRD和SEM等方法对Cu2(BTC)3进行了表征.实验结果表明,Cu2(BTC)3是一种典型的金属有机骨架(MOFs)材料,呈现规整的八面体晶状结构,晶粒大小为2～20 μm.相同条件下Cu2(BTC)3对CO2的吸附量高于活性炭和活性碳纤维,且随着吸附压力的升高吸附量明显增大,随着吸附温度的降低吸附量也增大.在0.4 MPa、25℃的条件下,用Cu2(BTC)3作吸附剂可以很好地分离CO2体积分数为5％和20％的CO2-甲烷混合气体,且对CO2含量低的混合气体分离效果更好.     

Activation of waste MDF sawdust charcoal and its reactive dye adsorption characteristics

This paper reports an experimental investigation of converting waste medium density fibreboard (MDF) sawdust into chars and activated carbon using chemical activation and thermal carbonisation processes. The MDF sawdust generated during the production of architectural mouldings was characterised and found to have unique properties in terms of fine particle size and high particle density. It also has a high content of urea formaldehyde resin used as a binder in the manufacturing of MDF board. Direct thermal carbonisation and chemical activation of the sawdust by metal impregnation and acid (phosphoric acid) treatment prior to pyrolysis treatment were carried out. The surface morphology of the raw dust, its chars and activated carbon were examined using scanning electron microscopy (SEM). Adsorptive properties and total pore volume of the materials were also analysed using the BET nitrogen adsorption method. Liquid adsorption of a reactive dye (Levafix Brilliant red E-4BA) by the derived sawdust carbon was investigated in batch isothermal adsorption process and the results compared to adsorption on to a commercial activated carbon (Filtrasorb F400). The MDF sawdust carbon exhibited in general a very low adsorption capacity towards the reactive dye, and physical characterisation of the carbon revealed that the conventional chemical activation and thermal carbonisation process were ineffective in developing a microporous structure in the dust particles. The small size of the powdery dust, the high particle density, and the presence of the urea formaldehyde resin all contributed to the difficulty of developing a proper porous structure during the thermal and chemical activation process. Finally, activation of the dust material in a consolidated form (cylindrical pellet) only achieved very limited improvement in the dye adsorption capacity. This original study, reporting some unexpected outcomes, may serve as a stepping-stone for future investigations of recycle and reuse of the waste MDF sawdust which is becoming an increasing environmental and cost liability.     

Sorbents for CO2 capture from high carbon fly ashes

Fly ashes with high-unburned-carbon content, referred to as fly ash carbons, are an increasing problem for the utility industry, since they cannot be marketed as a cement extender and, therefore, have to be disposed. Previous work has explored the potential development of amine-enriched fly ash carbons for CO(2) capture. However, their performance was lower than that of commercially available sorbents, probably because the samples investigated were not activated prior to impregnation and, therefore, had a very low surface area. Accordingly, the work described here focuses on the development of activated fly ash derived sorbents for CO(2) capture. The samples were steam activated at 850 degrees C, resulting in a significant increase of the surface area (1075m(2)/g). The activated samples were impregnated with different amine compounds, and the resultant samples were tested for CO(2) capture at different temperatures. The CO(2) adsorption of the parent and activated samples is typical of a physical adsorption process. The impregnation process results in a decrease of the surface areas, indicating a blocking of the porosity. The highest adsorption capacity at 30 and 70 degrees C for the amine impregnated activated carbons was probably due to a combination of physical adsorption inherent from the parent sample and chemical adsorption of the loaded amine groups. The CO(2) adsorption capacities for the activated amine impregnated samples are higher than those previously published for fly ash carbons without activation (68.6 vs. 45mg CO(2)/g sorbent).     

分子筛孔结构对CO_2吸附性能的影响

采用巨正则蒙特卡罗方法模拟了CO_2在FAU分子筛上的吸附情况,比较了不同CO_2逸度下,CO_2在分子筛模型上的吸附位、吸附量的变化,拟合了其吸附等温线。结果表明:在吸附饱和状态下,分子筛的孔结构越大,对CO_2的吸附量越大,对于比CO_2分子更小的微孔结构,吸附几乎不发生;在低逸度下,CO_2的吸附主要发生在小孔内,随着逸度的提高,CO_2的吸附量迅速上升;在高逸度下,吸附量的提高主要发生在大孔内;FAU分子筛吸附CO_2的过程符合Ⅰ型Langmuir吸附等温线,在高压下对CO_2的吸附能力远大于低压下的吸附能力。     

L-精氨酸溶剂化合成金属有机骨架化合物及其吸附CO2的性能

采用L-精氨酸对传统均苯三甲酸（BTC）溶剂热法合成的Cu基金属有机骨架化合物（Cu-BTC）进行改性，得到新型化合物（Cu-BTC-Arg），并通过固定床动态吸附实验考察了Cu-BTC-Arg和Cu-BTC吸附CO2的性能。表征结果显示：L-精氨酸只是辅助化溶剂，并未配位至Cu2+上；Cu-BTC-Arg比Cu-BTC具有更小的晶粒尺寸、更大的比表面积和微孔体积。实验结果表明，两种不同L-精氨酸加入量合成的Cu-BTC-Arg均在室温、烟气中无水蒸气、烟气流量80 mL/min的条件下CO2吸附量最大，吸附接近饱和时的CO2吸附量均为4.9 mmol/g，远高于Cu-BTC的CO2吸附量。Cu-BTC-Arg对CO2的吸附以物理吸附为主。     

响应面法优化阴阳极同时作用电化学法处理染料废水

在自制电化学反应器中,以甲基橙模拟染料废水为处理对象,采用Box-Behnken Design响应面法研究了影响阴阳极同时作用电化学法处理染料废水的因素及其交互作用。实验得出各因素对废水脱色率影响的大小顺序为：电流密度> Fe³⁺浓度>Cl^-浓度。各因素之间的交互作用对废水脱色率影响的大小顺序为：电流密度和Fe³⁺浓度>电流密度和Cl^-浓度>Fe³⁺浓度和Cl^-浓度。优化结果表明：Fe³⁺浓度为1.02 mmol/L、Cl^-浓度为10.96 mmol/L、电流密度为11.52 mA/cm²时,最佳脱色率为94.67%。阴阳极同时作用电化学法对甲基橙去除效果显著。     

粉煤灰两步水热法制备人工沸石

以粉煤灰为原料，采用两步水热法制备人工沸石。SEM、XRD、X射线荧光光谱分析结果表明:制得的人工沸石纯度较高，主要为Na-A型沸石和少量13X型沸石，主要化学成分为SiO2和Al2O3。说明采用两步法制备人工沸石克服了传统水热法杂质含量高的缺陷。采用人工沸石处理初始Mn2+质量浓度为50.00mg/L的模拟含锰废水，吸附125min后，Mn2+去除率达98.19%，模拟废水中剩余Mn2+质量浓度为0.90mg/L。     

粉煤灰及其制备沸石对高浓度氨氮的去除比较

以粉煤灰为原料,采用改进的水热合成法制备了粉煤灰沸石,并将粉煤灰和粉煤灰沸石用于高浓度氨氮的吸附去除。实验结果表明:在粉煤灰和粉煤灰沸石的投加量分别为0.10 g/m L和0.04 g/m L、反应体系p H为5~7、初始氨氮质量浓度为500 mg/L的条件下,分别吸附660 min和60 min,粉煤灰和粉煤灰沸石对氨氮的去除率分别约为20.1%和50.7%左右,粉煤灰沸石对高浓度氨氮的去除效果明显优于粉煤灰;粉煤灰和粉煤灰沸石对氨氮的吸附动力学行为符合准二级动力学方程;Langmuir和Freundlich等温吸附模型能较好地描述粉煤灰对氨氮的等温吸附过程,而粉煤灰沸石对氨氮的等温吸附过程则更适宜用线性模型和Freundlich模型描述。