燃煤锅炉湿法脱硫烟气中颗粒物排放特征

选择北京市典型燃煤锅炉进行研究,结果表明:烟气中可凝结颗粒物在总颗粒物中占有较高比例,供热燃煤锅炉总颗粒物排放水平明显高于电厂燃煤锅炉;颗粒物中水溶性离子含量较高,供热燃煤锅炉硫酸根比例尤其显著;烟气总颗粒物中存在大量不稳定的易被氧化的组分;同为燃煤源,不同的烟气净化工艺排放的PM2.5组分特征差异明显;现有标准和技术规范存在不足,无法满足全面、准确监测污染源排放总颗粒物的实际需要。建议建立总颗粒物、可凝结颗粒物的监测技术规范,全面测算燃煤锅炉硫、氮化合物排放情况,科学评估脱硫及脱硝效率。     

超低排放下燃煤电厂颗粒物排放特征分析研究

选取6家经过超低排放改造的燃煤电厂,对湿法脱硫(WFGD)和湿式电除尘器(WESP)进出口烟气中TPM、PM_(10)、PM_(2.5)、PM_1进行测试,分析研究超低排放下燃煤电厂颗粒物的排放特征及电除尘器后净化设备对颗粒物的脱除效果。结果表明,6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放浓度分别为0.75~2.36、0.71~2.12、0.65~1.96、0.51~1.57 mg/m~3。分析烟气中颗粒物粒径分布可知,除尘器后,PM10占TPM质量比低于40%,且比例随烟气经过WFGD和WESP而逐渐降低。WFGD对PM2.5有较好的脱除效果,而WESP对PM1脱除效果显著。为满足超低排放标准,6家电厂除尘器后脱除设备综合除尘效率大多在85%以上。计算得到6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放因子,与超低排放改造之前同等级燃煤电厂相比,6家电厂不同粒径颗粒物排放因子均显著降低,也远低于西方发达国家燃煤电厂颗粒物排放因子。     

全程加热采样管和半程加热采样管对超净排放污染源颗粒物监测结果的影响

根据《煤电节能减排升级与改造行动计划》以及《国家环境保护"十三五"规划纲要》,我国燃煤电厂污染物排放浓度应达到现行燃气锅炉标准,现行颗粒物监测仪器需要进行更新。现在市面上有2种污染源颗粒物采样管可对改造后电厂进行颗粒物采样监测,采用平行实验法对这2种采样管所采集的颗粒物质量结果进行分析,同时使用验证实验分析2种采样管颗粒物采集质量结果产生差异的原因,并对如何提升燃煤电厂颗粒物监测的准确性提出建议。     

因子分析法解析北京市大气颗粒物PM10的来源

2004年10月份在北京市6个采样点采集了大气PM10样品,分析了大气颗粒物的质量浓度、元素组成、离子、有机碳(OC)和元素碳(EC)的浓度,并用因子分析模型对颗粒物的来源进行了研究。结果显示,北京市大气颗粒物的来源主要有6类:建筑水泥尘/机动车尾气尘/燃煤尘、土壤风沙尘、二次粒子尘、工业粉尘、生物质燃烧尘和燃油尘。用模型计算得到的各源对PM10的贡献率分别为建筑水泥尘/机动车尾气尘/燃煤尘占36.57%、土壤风沙尘占16.07%、二次粒子尘占12.33%、工业粉尘占10.29%、生物质燃烧尘占6.07%、燃油尘占3.84%、其它占14.84%。其中建筑水泥/机动车尾气尘/燃煤尘、土壤风沙尘、二次粒子尘、工业粉尘是大气颗粒物PM10的主要来源。实验表明,在缺少源成分谱时可以用因子分析模型来分析大气颗粒物的来源及其相对贡献。     

典型超低排放烟气中颗粒物组分特征研究

为了解超低排放改造后工业源烟气颗粒物排放状况及其组分特征,于2020年1—5月对2家垃圾焚烧企业和2家燃煤电厂外排烟气开展了调查,同步采集外排烟气中的可过滤颗粒物（FPM）和可凝结颗粒物（CPM）,测定质量浓度及其离子组分、元素组分,对各组分浓度范围及平均值进行统计评价。结果表明：4家企业外排烟气中CPM和FPM质量浓度平均值的比值分别为30.5,10.3,3.0,0.94,CPM的排放不可忽视;离子分析结果发现,烟气处理过程中产生的铵离子和硫酸根离子等水溶性离子,在FPM中基本未检出,在CPM中检出且浓度较高;金属元素分析结果发现,检出的铬（Cr）、镍（Ni）、铅（Pb）3种元素主要存在于FPM中,而砷（As）、汞（Hg）元素则更多地存在于CPM中;CPM中水溶性离子为主要成分,以水溶性离子作为CPM排放的控制因子是可行的。     

内蒙古典型煤炭基地工业园大气TSP化学特征探究

监测2015年夏季内蒙古乌达-乌斯太工业园大气颗粒物TSP样品中多种无机元素和碳质组分，结果表明：工业园的TSP日均浓度明显高于国家环境空气质量标准，相关监测无机元素浓度均显著高于背景区乌海湖小岛。工业园碳质（OC/EC）测定值显著高于背景区，总碳气溶胶占比26.8%，其中以乌斯太工业园和乌达工业园采样点TCA占比较高。采用因子分析法对颗粒物元素组分分析发现主要有4类来源：园内复合地表污染扬尘、上风向地下煤火衍生污染物、交通源、园内燃煤电厂排放，贡献率分别为67%、27%、5%、1%。     

燃煤电厂石膏雨污染排放实测

对上海市8台燃煤机组开展了石膏雨和相关污染物排放监测,考察部分燃煤电厂石膏雨排放对周边居民生活和电厂生产造成的影响。结果表明,采用GGH并加热到一定温度,同时对除雾器进行优化的机组烟尘和可凝结颗粒物浓度均较低,石膏雨沉降和液滴均未检出,无冷凝回流液;虽然装有湿式电除尘器和GGH的机组石膏雨沉降未检出,但液滴浓度较高;仅装有湿式电除尘器的2台机组中1台检出石膏雨沉降;对照机组石膏雨沉降和液滴浓度均较高。建议电厂提升排烟温度,同时采取措施消除烟气中石膏夹带,彻底消除石膏雨,在标准制定时应充分考虑目前燃煤电厂多种污染物排放情况及其对环境的影响,尤其是石膏雨和可凝结颗粒物,制定相应的监测方法和评价体系,将其纳入火电厂排放标准中。     

石家庄市大气颗粒物元素组分特征分析

为研究石家庄市大气颗粒物的污染特征及其来源,于2013年4—5月在主城6区分别采集TSP、PM10和PM2.5颗粒物样品,利用ICP-MS分析其中的22种元素浓度。结果表明,石家庄市城区Ca、Fe元素在各粒径颗粒物中含量都较高,PM2.5中的S、K含量较高,PM10和TSP中Mg、Al的浓度相对较高。颗粒物的主要来源为燃煤尘、道路尘和建筑尘,TSP、PM10和PM2.5具有较好的统计相关性和同源性。     

对应分析在大气颗粒物源解析中的应用研究

采用对应分析方法定性研究龙岩市大气颗粒物来源问题。结果表明:龙岩市4个监测点位中龙岩市环境监测站的主要污染源为高岭土矿和土壤风沙尘;龙岩学院与闽西职业技术学院的主要污染源为机动车尾气尘、燃煤尘和土壤风沙尘;龙岩师专的主要污染源为燃煤尘、小煤炉尘、水泥成品、水泥厂除尘器集尘和钢铁厂除尘器集尘。该方法能将R型因子分析和Q型因子分析结合起来,综合体现样品和元素之间的关系,为大气颗粒物源解析提供了一种新的途径。     

燃油和燃煤电厂排放可吸入颗粒物的物理化学特性

分别对燃烧重油与烟煤两个电厂排放可吸入颗粒物的显微结构、颗粒类型及重金属在可吸入颗粒物中分布特征进行研究.研究表明,燃煤电厂排放可吸入颗粒物的形态都以球形颗粒为主,而燃油电厂排放可吸入颗粒物由一些絮状物和类似于燃煤飞灰中球形颗粒组成.根据可吸入颗粒物的化学组成,发现燃油电厂排放可吸入颗粒物的颗粒类型有硅铝质和钙-硅铝质...     

Study of Trace Elements and Soot in Aerosols from a Coal-Fired Power Plant in Northern Vietnam

Two measurement campaigns were conducted in two sampling sites, An Thinh and Duy Minh, in northern Vietnam during the months of November–December 2000 and November 2001–February 2002 in order to investigate the extend of the particulate air pollution from the Pha Lai coal fired power plant. Fine particle samples were analyzed by Energy Dispersive X-Ray Fluorescence spectrometry and soot samples were analyzed by reflectometer. The result showed that high concentration of soot and elements mostly coincided with the air masses originating from the power plant. Sea spray aerosol was found to be the major source of chlorine at both sites. Ratios of specific elements and principal component analysis (PCA) revealed that coal combustion was the main contributor to the air pollution at both sites. PCA also indicated that there were other sources responsible for the elements emission, probably the influence of long distance transport and Asian Brown Cloud.     

Radiological study of exposure levels in El Maghara underground coal mine

Coal is largely composed of organic matter, but it is the inorganic matter in coal minerals and trace elements that have been cited as possible causes of health, environmental and technological problems associated with the use of coal. Some trace elements in coal are naturally radioactive. These radioactive elements include uranium (U), thorium (Th) and their numerous decay products, including radium (Ra) and radon (Rn). Although these elements are less chemically toxic than other coal constituents, such as arsenic, selenium or mercury, questions have been raised concerning the possible risk from radiation. In order to accurately address these questions and to predict the mobility of radioactive elements during the coal fuel cycle, it is important to determine the specific activity, distribution and form of radioactive elements in coal. The assessment of the radiation exposure from coal burning is critically dependent on the specific activity of radioactive elements in coal and in the fly ash that remains after combustion. The El-Maghara coal mine is the only producing coal mine in Egypt. It is located in the middle of the Sinai desert about 250 km north-east of Cairo, where a coal-fired power plant is intended to be built. In this study, a pre-operational radiological baseline of the site and the occupational radiation exposures due to radon progeny in the mine were determined. The specific activities of 226Ra, 232Th and 40K in soil and coal dust samples collected along the main gallery ranges were found to be 6-22.9, 9.6-47.3 and 77-489 Bq kg-1, respectively. Soil samples collected around the mine showed concentrations of 226Ra, 232Th and 40K in the ranges 2.7-20.2, 3.2-12.6 and 14.6-201 Bq kg-1, respectively. All of the mean values of radon progeny were lower than the action levels for working places recommended in the International Commission on Radiological Protection (ICRP) 65.     

Comparative on Causes and Accumulation of Selenium in the Tree-rings Ambient High-selenium Coal Combustion Area from Yutangba, Hubei, China

Toxic trace elements emitted during coal combustion are the main sources of air pollution. They are released into the atmosphere mainly in the forms of fine ash, smoke and flue, and thus adversely affect plant, animal and human health. Selenium is one of toxic and the most volatile in coal. Large amount of atmospheric emission of selenium, as well as selenium present and scrubber stockpiles in ash may create serious environmental problems. In the paper, on the basis of investigating the abundance and distribution of selenium in plant-rings during recent 20 years, the bioaccumulation of selenium is explained that selenium in plant, which were collected from the village of selenium-rich coal combustion, is much higher than that in plants collected away from the village of selenium-rich coal combustion. The main origins of selenium are selenium-rich coal combustion and high-selenium rock weathered. The selenium recycle by food chain and selenium will accumulate and redistribute in environments.     

Leaching Characteristics of Fly Ash from Thermal Power Plants of Soma and Tunçbilek, Turkey

Use of lignite in power generation has led to increasing environmental problems associated not only with gaseous emissions but also with the disposal of ash residues. In particular, use of low quality coal with high ash content results in huge quantities of fly ash to be disposed of. The main problem related to fly ash disposal is the heavy metal content of the residue. In this regard, experimental results of numerous studies indicate that toxic trace metals may leach when fly ash contacts water. In this study, fly ash samples obtained from thermal power plants, namely Soma and Tunçbilek, located at the west part of Turkey, were subjected to toxicity tests such as European Committee for standardization (CEN) and toxicity characteristic leaching (TCLP) procedures of the U.S. Environmental Protection Agency (U.S. EPA). The geochemical composition of the tested ash samples from the power plant show variations depending on the coal burned in the plants. Furthermore, the CEN and TCLP extraction results showed variations such that the ash samples were classified as `toxic waste' based on TCLP result whereas they were classified as `non-toxic' wastes based on CEN results, indicating test results are pH dependent.     

Speciation and sources of atmospheric aerosols in a highly industrialised emerging mega-city in central China

Monitoring air quality in large urban agglomerations is the key to the prevention of air pollution-related problems in emerging mega-cities. The city of Wuhan is a highly industrialised city with >9 million inhabitants in Central China. Simultaneous PM10 sampling was performed during 1 year at one urban and one industrial site. Mean PM10 daily levels (156 microg m(-3) at the urban site and 197 microg m(-3) at the industrial hotspot) exceed the US-EPA or EU annual limit values by 3-4 times. A detailed study of daily speciation showed that the mean chemical composition of PM10 presents minimal differences between peak and low PM episodes. This implies that PM10 aerosols in the study area result from local emissions, and air quality management and abatement strategies in Wuhan should thus focus on local anthropogenic sources. The levels of some elements of environmental concern are relatively high (409-615 ngPb m(-3), 66-70 ngAs m(-3), 116-227 ngMn m(-3), 10-12 ngCd m(-3)) due to industrial, but also urban emissions. Principal component analysis identified a mineral source (probably cement and steel manufacture) and smelting as the main contributors to PM10 levels at the industrial site (34%), followed by a coal fired power plant (20%) and the anthropogenic regional background (16%). At the urban site the major PM10 source is a mixed coal combustion source (31%), followed by the anthropogenic regional background (28%) and traffic (16%).     

Behavior study of trace elements in pulverized lignite, bottom ash, and fly ash of Amyntaio power station, Greece

The Kozani–Ptolemais–Amyntaio basin constitutes the principal coal field of Greece. Approximately 50 % of the total power production of Greece is generated by five power stations operating in the area. Lignite samples, together with the corresponding fly ash and bottom ash were collected, over a period of 3 months, from the power plant of Amyntaio and analyzed for their content in 16 trace elements. The results indicate that Y, Nb, U, Rb, Zr, Ni, Pb, Ba, Zn, Sr, Cu, and Th demonstrate an organic affinity during the combustion of lignite, while V has an inorganic affinity. Three elements (Co, Cr, and Sc) show an intermediate affinity.     

Morphology,microstructure and chemical composition of single inhalable particles in Shanghai,China

The morphology, microstructure, and chemical composition of a variety of particles emitted from coal-fired power plants, steel plants, and vehicle exhausts, which are possible sources of particulate matter (PM) in the atmosphere, were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and compared with particle samples collected from urban atmosphere to identify the best footprint or the suitable indicator relating the existence of studied particles and their possible emitters by the morphology, microstructure, and chemical composition of the particles. The investigation indicated that the particles from these three sources are different in morphology, microstructure, and chemical composition. Sphere aggregates were generally the most abundant components, with silicon and aluminum as major elements. The urban air particulate contained particles similar to those observed in the power plant, steel plant, and vehicle exhaust samples suggesting that all three sources are contributing to the pollution in the city.     

Four trace elements contents of water environment of mining subsidence in the Huainan diggings, China

Mining subsidence pool is the special waters formed by coal mining, located near the mine. We understand the impact on these waters of the surrounding coal production activities and the electricity plant through research the content and characteristics of harmful trace elements in coal contained in these waters. Pb, Hg, Se and Cr these four trace elements increase 0.52, 0.78, 0.70 and 0.28% respectively in Datong mining subsidence pool from November 2004 to November 2006; the four elements increase 1.52, 1.23, 1.08 and 1.08% respectively in Xie'er mining subsidence pool; the four elements increase 1.01, 1.06, 1.02 and 0.83% respectively in Pansan mining subsidence pool. The absolute value of Pb, Hg, Se and Cr in mining subsidence pool is related with their background value, while the increase in their concentration and their environment of mine and electricity plant surrounded are closely linked.     

基于实测的燃煤电厂烟气中汞排放水平浅析

简述汞污染和控制问题成为环境问题的新热点和前沿研究领域,介绍中国燃煤电厂烟气汞监测试点的基本情况。分析江苏省7家燃煤电厂煤中汞及烟气中汞排放水平,提出利用现有的除尘、脱硫、脱硝设施,能满足《火电厂大气污染物排放标准》中汞的排放限值要求。     

南京燃煤电厂烟气中汞的排放调查

对南京市8家国控污染源13台（套）燃煤锅炉进行监测，结果表明，燃煤电厂烟气中汞主要以气相部分汞形态存在，其排放值均达标，为0．16～15．9μg／m3，均远低于标准限值；煤质中汞含量与电厂烟气中汞浓度变化曲线的趋势是大致相似，相关系数为0．91；燃煤电厂机组容量、发电负荷越大，汞平均排放因子呈变小趋势；静电除尘器、湿法脱硫和选择性催化还原法的净化配置对汞的脱除效率最高，达到95．4％。