Petrographic and spectroscopic characterization of phosphate-stabilized mine tailings from Leadville,Colorado

The use of soluble PO4(3-) and lime as a heavy metal chemical stabilization agent was evaluated for mine tailings from Leadville, Colorado. The tailings are from piles associated with the Wolftone and Maid of Erin mines; ore material that was originally mined around 1900, reprocessed in the 1940s, and now requires stabilization. The dominant minerals in the tailings are galena (PbS), cerrusite (PbCO3), pyromorphite (Pb5(PO4)3Cl), plumbojarosite (Pb0.5Fe3(SO4)2(OH)6), and chalcophanites ((Pb,Fe,Zn,Mn)Mn2O5 x 2H2O). The tailings were treated with soluble PO4(3-) and lime to convert soluble heavy metals (principally Pb, Zn, Cu, Cd) into insoluble metal phosphate precipitates. The treatment process caused bulk mineralogical transformations as well as the formation of a reaction rind around the particles dominated by Ca and P. Within the mineral grains, Fe-Pb phosphosulfates, Fe-Pb sulfates (plumbojarosite), and galena convert to Fe-Ca-Pb hydroxides. The Mn-Pb hydroxides and Mn-(+/-Fe)-Pb hydroxides (chalcophanites) undergo chemical alteration throughout the grains during treatment. Bulk and surface spectroscopies showed that the insoluble reaction products in the rind are tertiary metal phosphate (e.g. (Cu,Ca2)(PO4)2) and apatite (e.g. Pb5(PO4)3Cl) family minerals. pH-dependent leaching (pH 4,6,8) showed that the treatment was able to reduce equilibrium concentrations by factors of 3 to 150 for many metals; particularly Pb2+, Zn2+, Cd2+, and Cu2+. Geochemical thermodynamic equilibrium modeling showed that apatite family and tertiary metal phosphate phases act as controlling solids for the equilibrium concentrations of Ca2+, PO4(3-) Pb2+, Zn2+, Cd2+, and Cu2+ in the leachates during pH-dependent leaching. Both end members and ideal solid solutions were seen to be controlling solids.     

An investigation on the potential of metal recovery from the municipal waste incinerator in Taiwan

This study aimed to identify distribution of metals and to estimate the amount of these metals that can be potentially recovered from incineration residues. First, the partitioning behavior of Cr, Cu, Fe, Cd, Al, Zn, and Pb in bottom ash and fly ash was investigated in one large municipal waste incinerator in Taiwan. In addition, the material flow analysis (MFA) method was used to estimate the material flux of metals within incinerator plant, and to calculate the amount of metal recovery. According to the findings of this study, six metals (Fe, Al, Cu, Zn, Cr, and Pb) concentrated in bottom ash mostly, while Cd existed primarily in fly ash. The weight percentages of Fe (4.49%), Al (5.24%), Cu (1.29%), Zn (2.21%), and Pb (0.58%) in incinerator ash are high, and even higher than the compositions of natural minerals. Finally, the amount of Cr, Cu, Fe, Cd, Al, Zn and Pb that can be potentially recovered from incineration residues will reach 2.69 x 10(2), 1.46 x 10(4), 4.91 x 10(4), 6.92 x 10(1), 5.10 x 10(4), 1.85 x 10(4) and 4.66 x 10(3) ton/yr, respectively.     

Chemical and mineralogical evaluation of slag products derived from the pyrolysis/melting treatment of MSW

This paper provides the results of studies on the characteristics of novel material derived from pyrolysis/melting treatment of municipal solid waste in Japan. Slag products from pyrolysis/melting plants were sampled for the purpose of detailed phase analysis and characterization of heavy metal-containing phases using optical microscopy, electron probe microanalysis (EPMA), XRF and XRD. The study revealed that the slag material contains glass (over 95%), oxide and silicate minerals (spinel, melilite, pseudowollastonite), as well as individual metallic inclusions as the major constituents. A distinct chemical diversity was discovered in the interstitial glass in terms of silica content defined as low and high silica glass end members. Elevated concentrations of Zn, Cr, Cu, Pb and Ba were recorded in the bulk composition. Cu, Pb and Ba behave as incompatible elements since they have been markedly characterized as part of polymetallic alloys and insignificantly sulfides in the form of spherical metallic inclusions associated with tracer amounts of other elements such as Sb, Sn, Ni, Zn, Al, P and Si. In contrast, an appreciable amount of Zn is retained by zinc-rich end members of spinel and partially by melilite and silica glass. Chromium exhibits similar behavior, and is considerably held by Cr-rich spinel. The intense incorporation of Zn and Cr into spinel indicates the very effective enrichment of these two elements into phases more environmentally resistant than glass. There was no evidence, however, that Cu and Pb enter into the structure of the crystalline silicates or oxides that may lead to their easier leachability upon exposure to the environment.     

Stabilization of As, Cr, Cu, Pb and Zn in soil using amendments--a review

The spread of contaminants in soil can be hindered by the soil stabilization technique. Contaminant immobilizing amendments decrease trace element leaching and their bioavailability by inducing various sorption processes: adsorption to mineral surfaces, formation of stable complexes with organic ligands, surface precipitation and ion exchange. Precipitation as salts and co-precipitation can also contribute to reducing contaminant mobility. The technique can be used in in situ and ex situ applications to reclaim and re-vegetate industrially devastated areas and mine-spoils, improve soil quality and reduce contaminant mobility by stabilizing agents and a beneficial use of industrial by-products. This study is an overview of data published during the last five years on the immobilization of one metalloid, As, and four heavy metals, Cr, Cu, Pb and Zn, in soils. The most extensively studied amendments for As immobilization are Fe containing materials. The immobilization of As occurs through adsorption on Fe oxides by replacing the surface hydroxyl groups with the As ions, as well as by the formation of amorphous Fe(III) arsenates and/or insoluble secondary oxidation minerals. Cr stabilization mainly deals with Cr reduction from its toxic and mobile hexavalent form Cr(VI) to stable in natural environments Cr(III). The reduction is accelerated in soil by the presence of organic matter and divalent iron. Clays, carbonates, phosphates and Fe oxides were the common amendments tested for Cu immobilization. The suggested mechanisms of Cu retention were precipitation of Cu carbonates and oxy-hydroxides, ion exchange and formation of ternary cation-anion complexes on the surface of Fe and Al oxy-hydroxides. Most of the studies on Pb stabilization were performed using various phosphorus-containing amendments, which reduce the Pb mobility by ionic exchange and precipitation of pyromorphite-type minerals. Zn can be successfully immobilized in soil by phosphorus amendments and clays.     

Thermodynamic analysis on heavy metals partitioning impacted by moisture during the MSW incineration

A thermodynamic calculation was carried out to predict the behavior and speciation of heavy metals (HMs), Pb, Zn, Cu, and Cd, during municipal solid waste (MSW) incineration with the different moisture levels. The calculation was based on the minimization of the total Gibbs free energy of the multi-components and multi-phases closed system reaching chemical equilibrium. The calculation also indicated the reaction directions and tendencies of HMs components. The impacts of chlorine additives (No PVC, 1%PVC, and 5%PVC) and moisture on the behavior of HMs were investigated at different temperature levels in the system (750 °C, 950 °C, and 1150 °C). Furthermore, because the incineration temperature falls down with the increase in moisture in waste, the co-influence of moisture and temperature in combusting MSW on the HMs was also studied with the given chlorine (as 1%PVC + 0.5%NaCl). The results showed that in the non-chlorine system, the impact of the moisture on Pb, Zn, and Cu was not significant, and the ratio of compound transformation was less than 10%, except the Cd compounds at 950 °C and 1150 °C. In the system with low chlorine (as 1%PVC) at constant temperature, the chlorides of HMs (Cd, Pb, Zn, and Cu) transferred to oxides, and when the content of chlorine rose up (as 5%PVC), the ratio of the chlorides of HMs (Cd, Pb, Zn, and Cu) transferring to oxides fell down noticeably. When the moisture varied together with the temperature, the Zn and Cu compounds transferred from chlorides to oxides with increase in moisture as well as decrease in temperature. At the temperature of 700–1000 °C, the impact of temperature on Pb and Cd was little and the moisture was the main factor; while at the temperature of 1000–1200 °C, the impact of increase in moisture and decrease in temperature on Pb and Cd was almost equal and reversed.     

The effect of sediment redox chemistry on solubility/chemically active forms of selected metals in bottom sediment receiving produced water discharge

The effect of sediment redox conditions on the solubility behavior of Fe, Pb, Ni, Ba, and Cu in bottom sediment collected from a produce water discharge site was investigated using kinetics and chemical fractionation procedures. Sediment collected was composited and subsamples incubated in laboratory microcosms under controlled Eh-pH conditions. Sediment was sequentially extracted for determining metals in five fractions (exchangeable, carbonate, bound to iron and manganese oxide, bound to organic matter and sulfide, mineral matrix or residue). Metal distribution in the fractions indicates that under oxidizing sediment conditions, the behavior of Fe, Pb and Ni were governed by Fe(III) and Mn(IV) oxides; Ba by insoluble complexation with humic compounds; and Cu by carbonates and humic complexation. Under reducing sediment condition, the behaviors of Fe and Cu were controlled by the formation of insoluble sulfides and humic complexes; the behaviors of Ni and Ba by carbonate and Pb behavior by sulfides, carbonates and humic complexes. With increases in sediment redox potential, the affinity between Fe(III), Mn(IV) oxides and Fe, Pb, Ni, Cu increased, the affinity between insoluble large molecular humic and Ba increased, and the affinity between carbonates and Cu increased. With decreasing sediment redox potential, the affinity between carbonates and Fe, Ni, Ba increased; the affinity between sulfides, humic substances and Fe, Pb, Ni, Cu also increased. Upon Fe(III) oxide reduction, it is estimated that 20% of total reducible Fe(III) oxides was reduced by direct bacterial reduction (K = −42.6 ppm/day), 80% of total reducible Fe(III) oxides was associated with chemical fractions attributed to sulfide oxidation (K = −171.5 ppm/day). The rate constants (ppm/day) for dissolved Ni (Eh <0 mV), Pb (Eh < −80 mV) and Cu (−80 mV < Eh <0 mV) are −1.6, −0.047 and −0.16, respectively. In our incubation period, the rate constants (ppm/day) for Ni bound to Fe(III) and Mn(IV) oxides, Ba bound to carbonates and Cu bound to insoluble large molecular humic are −3.2, 0.91 and 4.3, respectively.     

铅冶炼烟尘的物性分析及浸出性研究

采用XRF、XRD、激光粒度分析、DTA-TG、FTIR以及SEM-EDS等技术，对某铅冶炼厂烟尘（简称烟尘）进行了物性分析，并采用稀硫酸对烟尘进行了浸出性研究。分析结果表明：烟尘所含主要元素为Pb，Zn，Cd，Cl，S，As;烟尘是氧化物、硫酸盐、硅酸盐、硫化物和砷化物等物质的混合物，主要物相为ZnO，PbO，PbSO₄，CdO，CdS;烟尘颗粒大小不一，形状各异，多呈相互黏结或包裹状。实验结果表明：在ρ（硫酸）=120 g/L、浸出时间30 min、液固比（稀硫酸体积（mL）与烟尘质量（g）之比）20∶1、浸出温度60 ℃的条件下，Pb，Zn，Cd，As，Cl的浸出率分别达到0.16%，98.95%，49.36%，89.12%，99.31%。     

Investigation of potentially toxic heavy metals in different organic wastes used to fertilize market garden crops

The benefits of using organic waste as fertilizer and soil amendment should be assessed together with the environmental impacts due to the possible presence of heavy metals (HMs). This study involved analysing major element and HM contents in raw and size-fractionated organic wastes (17 sewage sludges and composts) from developed and developing countries. The overall HM concentration pattern showed an asymmetric distribution due to the presence of some wastes with extremely high concentrations. HM concentrations were correlated with the size of cities or farms where the wastes had been produced, and HM were differentiated with respect to their origins (geogenic: Cr–Ni; anthropogenic agricultural and urban: Cu–Zn; anthropogenic urban: Cd–Pb). Size fractionation highlighted Cd, Cu, Zn and Pb accumulation in fine size fractions, while Cr and Ni were accumulated in the coarsest. HM associations with major elements revealed inorganic (Al, Fe, etc.) bearing phases for Cr and Ni, and sulfur or phosphorus species for Cd, Cu Pb and Zn.     

Effect of nine years of animal waste deposition on profile distribution of heavy metals in Abeokuta,south-western Nigeria and its implication for environmental quality

Uncontrolled deposition of waste from animal farms is a common practice in south-western Nigeria, and the presence of heavy metals in soil constitutes environmental and health hazards by polluting the soil, ground water, adjoining streams and rivers. The study investigated the profile distribution of Mn, Pb, Cd, Zn, Fe, Cu, Ni and Cr in some tropical Alfisols in south-western Nigeria after nine years disposal of animal wastes. The amount of these metals in the soil horizons was high enough to cause health and phytotoxic risks. All the metals except Zn and Cr increased down the profile, while Mn, Pb, Cd, Fe, Cu and Ni accumulated at 80–120 cm depth. The increment of these metals at this depth over the top soil were 26%, 143%, 72%, 47%, 328% for Mn, Pb, Cd, Cu and Ni, respectively. It thus, shows their mobility and the possibility of polluting ground water. The Mn content at the poultry and cattle waste sites increased by 127% and 25%, respectively over the control, while that of cattle and swine dump site for Cd content were 9.82 and 15.63 mg kg^?1, respectively. Lead content also increased by 8.52 and 5.25 mg kg^?1, respectively.There was the accumulation of Zn and Cu at the swine dump site while the cattle dump site had the highest amounts of nickel and chromium. The least amount of Fe was recorded at the swine waste dump site. The reduction in organic matter with depths together with the reduced pH might have favored the mobility of the metals. The ranking of pollution among the sites was poultry > swine > cattle > sheep and could be due to the type of ration fed, the vaccination programmes, sanitation programmes and other management practices.     

Salinity, organic content, micronutrients and heavy metals in pig slurries from South-eastern Spain

The increase in commercial pig production is an opportunity to reuse animal manures in arid and semiarid soils as a source of nutrients and organic matter. However, there are components in pig slurry that are potentially dangerous for the environment. In this study, pig slurries of 36 pig farms in South-eastern Spain were evaluated for salt content (electrical conductivity, chloride and sodium), organic load (BOD5 and COD), micronutrients (Fe, Cu, Mn and Zn), and heavy metals (Cd, Co, Cr, Ni and Pb). Except for electrical conductivity, Cu and Zn, components in pig slurries did not vary considerably between animal production stages, indicating similar management of diverse animal types. Assuming an application rate based on the maximum input of nitrogen from animal manure (210 kg total N/ha/yr), the estimates for soil annual load of Cl and Na, 415 kg/ha, could be a significant salinisation risk. Cu and Zn seemed to be the metals that could be accumulated most in soils where application of pig slurries is common (4 and 15 kg/ha/yr, respectively). The estimated heavy metal (Cd, Co, Cr, Ni and Pb) input to soils would be 260 g/ha/yr, with a relative contribution of Cr>Ni>Pb>Co>Cd.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Variations of metal distribution in sewage sludge composting

In the study, the variations of heavy metal distributions (of Cu, Mn, Pb, and Zn) during the sewage sludge composting process were investigated by sequential extraction procedures. The total content of Cu and Zn in the composted mixture increased after the composting process. Mn and Zn were mainly found in mobile fractions (exchangeable fraction (F1), carbonate fraction (F2), and Fe/Mn oxide fraction (F3)). Cu and Pb were strongly associated with the stable fractions (organic matter/sulfides fraction (F4) and residual fraction (F5)). These five metal fractions were used to calculate the metal mobility (bioavailability) in the sewage sludge and composted mixture. The mobility (bioavailability) of Mn, Pb, and Zn (but not Cu) increased during the composting process. The metal mobility in the composted mixture ranked in the following order: Mn>Zn>Pb>Cu.     

Waste rechargeable electric lamps: characterisation and recovery of lead from their lead-acid batteries

Electrical electronics constitute a significant quantity of municipal solid wastes which are discarded after use in open dumpsites especially in the developing countries. The aim of this study was to characterise the material and chemical components, evaluate current management practices and investigate recovery of lead from battery electrodes (BEs) of waste rechargeable electric lamps (RLs). Twenty-six waste RLs of different models were sampled in Nigeria and characterised. Their BEs were analysed for Pb, Cr, Mn, Cu, Zn, Ni and Fe after acid digestion. Questionnaires were distributed to unselected respondents to assess usage and disposal of the lamps. Reaction of citric acid solutions with Pb in the presence of H₂O₂ was used for the recovery of Pb. 69 % of the respondents disposed their waste RLs in open dumpsites. The mean ± SD concentrations of Pb, Cr, Mn, Cu, Zn, Ni and Fe in the BEs were 600 ± 0.2 g/kg, 65.4 ± 40 mg/kg, 5.05 ± 4.0 mg/kg, 6.81 ± 5.0 mg/kg, 5.98 ± 3.0 mg/kg, 50.0 ± 30 mg/kg and 40.2 ± 35 mg/kg, respectively. The results show that the batteries are lead-acid batteries which require management. At the optimal conditions of S/L = 0.14, temperature = 20 °C and leaching time = 5 h, about 95 % Pb was recovered in form of lead citrate from the battery. High recovery of Pb is possible with simple and environment-friendly reactions.     

Effects of Acid Rain on Competitive Releases of Cd, Cu, and Zn from Two Natural Soils and Two Contaminated Soils in Hunan, China

Leaching experiments of rebuilt soil columns with two simulated acid rain solutions (pH 4.6–3.8) were conducted for two natural soils and two artificial contaminated soils from Hunan, south-central China, to study effects of acid rain on competitive releases of soil Cd, Cu, and Zn. Distilled water was used in comparison. The results showed that the total releases were Zn>Cu>Cd for the natural soils and Cd>Zn≫Cu for the contaminated soils, which reflected sensitivity of these metals to acid rain. Leached with different acid rain, about 26–76% of external Cd and 11–68% external Zn were released, but more than 99% of external Cu was adsorbed by the soils, and therefore Cu had a different sorption and desorption pattern from Cd and Zn. Metal releases were obviously correlated with releases of TOC in the leachates, which could be described as an exponential equation. Compared with the natural soils, acid rain not only led to changes in total metal contents, but also in metal fraction distributions in the contaminated soils. More acidified soils had a lower sorption capacity to metals, mostly related to soil properties such as pH, organic matter, soil particles, adsorbed SO₄ ²⁻, exchangeable Al³⁺ and H⁺, and contents of Fe₂O₃ and Al₂O₃.     

Thermodynamic assessment in heavy metal migration at El-Akader landfill site,North Jordan

Thermodynamic analysis of subsoil pore water indicates that Fe, Cu, Zn, and Pb exist as a metal hydroxy complex of the forms [Me OH] + and [Me(OH2)]o, although a complex of [PbCl]+ is also significant, but not predominant. The analysis also demonstrates that the dissolved transition metal concentration of the subsoil pore waters are controlled at carbonate minerals saturation levels, whereas Fe concentration in leachate solutions associated with waters are controlled at FeS2 saturation levels. Thermodynamic calculations and Eh-pH diagrams suggest that Fe(OH)2, Zn(OH)2 and Pb(OH)2 are not stable phases in the solids of the subsoil.     

Metal distribution in incineration residues of municipal solid waste (MSW) in Japan

This study aimed to identify distribution of metals and the influential factors on metal concentrations in incineration residues. Bottom ash and fly ash were sampled from 19 stoker and seven fluidized bed incinerators, which were selected to have a variety of furnace capacity, furnace temperature, and input waste. In the results, shredded bulky waste in input waste increased the concentration of some metals, such as Cd and Pb, and the effect was confirmed by analysis of shredded bulky waste. During MSW incineration, lithophilic metals such as Fe, Cu, Cr, and Al remained mainly in the bottom ash while Cd volatilized from the furnace and condensed to the fly ash. About two thirds of Pb and Zn was found in the bottom ash despite their high volatility. Finally, based on the results obtained in this study, the amount of metal in incineration residues of MSW was calculated and the loss of metal was estimated in terms of mass and money. A considerable amount of metal was found to be lost as waste material by landfilling of incineration residues.     

Recovery of metals from waste printed circuit boards by supercritical water pre-treatment combined with acid leaching process

Waste printed circuit boards (PCBs) contain a large number of metals such as Cu, Sn, Pb, Cd, Cr, Zn, and Mn. In this work, an efficient and environmentally friendly process for metals recovery from waste PCBs by supercritical water (SCW) pre-treatment combined with acid leaching was developed. In the proposed process, waste PCBs were pre-treated by SCW, then the separated solid phase product with concentrated metals was subjected to an acid leaching process for metals recovery. The effect of SCW pre-treatment on the recovery of different metals from waste PCBs was investigated. Two methods of SCW pre-treatment were studied: supercritical water oxidation (SCWO) and supercritical water depolymerization (SCWD). Experimental results indicated that SCWO and SCWD pre-treatment had significant effect on the recovery of different metals. SCWO pre-treatment was highly efficient for enhancing the recovery of Cu and Pb, and the recovery efficiency increased significantly with increasing pre-treatment temperature. The recovery efficiency of Cu and Pb for SCWO pre-treatment at 420 °C was 99.8% and 80%, respectively, whereas most of the Sn and Cr were immobilized in the residue. The recovery of all studied metals was enhanced by SCWD pre-treatment and increased along with pre-treatment temperature. Up to 90% of Sn, Zn, Cr, Cd, and Mn could be recovered for SCWD pre-treatment at 440 °C.     

Field investigation of the quality of fresh and aged leachates from selected landfills receiving e-waste in an arid climate

The management of electronic waste (e-waste) is a serious problem worldwide and much of it is landfilled. A survey of four selected landfills in an arid region of South Australia was conducted to determine the proportion of e-waste in municipal waste and the properties of each landfill site. Leachate and groundwater samples were collected upgradient and downgradient of the landfills for analysis of polybrominated diphenyl ethers (PBDEs) and 14 metals and metalloids, including Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Ni, Pb, Sb, V and Zn. Our data demonstrate that the selected landfills in South Australia continue to receive municipal waste containing in excess of 6%, or 25,000 tonnes per year, of e-waste. The leachates and groundwater collected from the landfills contained significantly elevated concentrations of Pb with the highest concentration in groundwater of 38 μg/l, almost four times higher than the Australian drinking water guideline of 10 μg/l. The presence of PBDEs was detected in both leachate and groundwater samples. Total PBDEs values of 2.13–59.75 ng/l in leachate samples were 10 times higher than in groundwater samples, which recorded a range of 0.41–6.53 ng/l at all sites. Moreover, the concentrations of metals and metalloids in sampled groundwater contained elevated levels of Al, As, Fe, Ni and Pb that exceeded Australian drinking water guideline values. For these reasons potential leaching of these contaminants is of concern and while difficult to attribute elevated contaminant levels to e-waste, we do not recommend continued disposal of e-waste in old landfills that were not originally designed to contain leachates. The survey also revealed temporal variation in the electrical conductivity and concentrations of As, Cd and Pb present in leachates of landfills in arid Mediterranean climates. These results are consistent with the marked variations in rainfall patterns observed for such climates. The solute concentration (EC and other ions including As, Cd and Pb) declines in the leachates during wet winter months (June to September), in contrast to tropical countries where such changes are observed during wet summer months.     

Metals in Sediments from the Stockholm Region: Geographical Pollution Patterns and Time Trends

The city of Stockholm is intersected and surrounded by water.Freshwater flows eastward and mixes with slightly brackish water in central Stockholm to finally reach the Baltic Sea. Inorder to estimate the magnitude and geographical impact of Stockholm as a source of metals to the aquatic environments, sediments from 117 stations in the Stockholm region have beenanalysed for metals (As, Cd, Co, Cr, Cu, Hg, Ni, Pb and Zn).This paper reports on the geographical pollution pattern and onthe time trends in metal pollution in Stockholm during the 20th century. Stockholm is a strong source of Cd, Cu, Hg,Pb and Zn whereas the Cr concentrations are moderately perturbed.In contrast, the concentrations of As, Co, and Ni are in generalclose to preindustrial levels. The concentrations of Cd, Cu, Hg,Pb and Zn are highest in central Stockholm and eastwards (i.e., in the water flow direction). Sediments upstream of Stockholm andin lakes that are not hydrologically connected to central Stockholm show a significantly lower impact. This may be indicative of metals emitted in Stockholm mainly being transported by the water route. Of Cd, Hg, Pb, and Zn, Cd showsthe most pronounced decline in accumulation rates over the lasttwo decades.