Transport and biodegradation of perchlorate in soils

Perchlorate (ClO4-) contamination of ground water and surface water is a widespread problem, particularly in the western United States. This study examined the effect of biodegradation on perchlorate fate and transport in soils. Solute transport experiments were conducted on two surface soils. Pulses of solution containing perchlorate and Br- were applied to saturated soil columns at steady state water flow. Perchlorate behaved like a nonreactive tracer in Columbia loam (coarse-loamy, mixed, superactive, nonacid, thermic Oxyaquic Xerofluvent) but was degraded in Yolo loam (fine-silty, mixed, superactive, nonacid, thermic Mollic Xerofluvent). Batch experiments demonstrated that perchlorate removal from solution in Yolo loam was caused by biodegradation. Other batch experiments with Yolo loam surface and subsurface soils, Columbia loam surface soil, and dredge tailings demonstrated that perchlorate biodegradation required anaerobic conditions, an adequate carbon source, and an active perchlorate-degrading microbial population. The sequential reduction of perchlorate and NO3- by an indigenous soil microbial community in Yolo loam batch systems was also studied. Nitrate reduction occurred much sooner than perchlorate reduction in soils that had not been previously exposed to perchlorate, but NO3- and perchlorate were simultaneously reduced in soils previously exposed to perchlorate. The results of this study have implications for in situ remediation schemes and for agricultural soils that have been contaminated by perchlorate-tainted irrigation water.     

Effects of wood bark and fertilizer amendment on trace element mobility in mine soils, Broken Hill, Australia: implications for mined land reclamation

Soil amendments can immobilize metals in soils, reducing the risks of metal exposure and associated impacts to flora, fauna and human health. In this study, soil amendments were compared, based on "closed system" water extracts, for reducing metal mobility in metal-contaminated soil from the Broken Hill mining center, Australia. Phosphatefertilizer (bovine bone meal, superphosphate, triple superphosphate, potassium orthophosphate) and pine bark (Pinus radiata) were applied to two soils (BH1, BH2) contaminated with mining waste. Both soils had near neutral to alkaline pH values, were sulfide- or sulfate-rich, and contained metal and metalloid at concentrations that pose high environmental risks (e.g., Pb = 1.25 wt% and 0.55 wt%, Zn = 0.71 wt% and 0.47 wt% for BH1 and BH2, respectively). The addition of fertilizers and/or pine bark to both soil types increased water extractable metals and metalloids concentrations (As, Cd, Cu, Fe, Mn, Pb, Sb, Zn) compared with nonamended soils. One or more of the elements As, Cd, Cu, Mn, Pb, and Zn increased significantly in extracts of a range of different soil+pine bark and soil+fertilizer+piner+pine bark tests in response to increased pine bark doses. By contrast, Fe and Sb concentrations in extracts did not change significantly with pine bark addition. Solution pH was decreased by phosphate fertilizers (except for bovine bone meal) and pine bark, and pine bark enhanced dissolved organic carbon. At least in the short-term, the application of phosphate fertilizers and pine bark proved to be an ineffective method for controlling metal and metalloid mobility in soils that contain admixtures of polymetallic, polymineralic mine wastes.     

Fractionation and mobility of copper, lead, and zinc in soil profiles in the vicinity of a copper smelter

Four soil profiles located near a copper smelter in Poland were investigated for the distribution and chemical fractions of Cu, Pb, and Zn and their mobility in relation to soil properties. Contamination with heavy metals was primarily restricted to surface horizons and the extent of contamination was 7- to 115-fold for Cu, 30-fold for Pb, and 6-fold for Zn as compared with subsurface horizons. In the less-contaminated fine-textured soil, the metals were distributed in the order: residual > Fe-Mn oxides occluded > organically complexed > exchangeable and specifically adsorbed, while the order for sandy soils was: residual > organically complexed > Fe-Mn oxides occluded > exchangeable and specifically adsorbed. The contaminated surface horizons of these profiles showed no consistent pattern of metal distribution. However, the common features of highly contaminated soils were very low percentage of residual fraction and the dominance of the NH4OAc extractable fraction. The sum of mobile metal fractions was generally < 10% in subsurface horizons, while in the contaminated surface horizons these fractions made up 50% of the total metal contents. Soil properties contributed more to the relative distribution of the metal fractions in the studied profiles than did the distance and direction to the source of pollution. The amounts of metal extracted by 0.01 M CaCl2 accounted for only a small part of the same metals extracted by NH4OAc. The mobility indexes of metals correlated positively and significantly with the total content of metals and negatively with the clay content.     

Occurrence of metals in soil and ground water near chromated copper arsenate-treated utility poles

To thoroughly investigate the metal contamination around chromated copper arsenate (CCA)/polyethylene glycol (PEG)-treated utility poles, a total of 189 soil samples obtained from different depths and distances near six treated poles in the Montreal area (Canada) were analyzed for Cu, Cr, and As content. Various soil physicochemical properties were also determined. Ground water samples collected below the poles were analyzed for metals and bioassays with Daphnia magna were conducted. Generally, sandy soils had lower contaminant levels than clayey and organic soils. Copper concentrations in soil were highest followed by As and Cr. The highest Cu (1460 +/- 677 mg kg(-1)), As (410 +/- 150 mg kg(-1)), and Cr (287 +/- 32 mg kg(-1)) concentrations were found at the ground line and immediately adjacent to the pole. Contaminant levels then decreased with distance, approaching background levels within 0.1 m from the pole for Cr and 0.5 m for Cu and As. Chromium and Cu levels generally approached background levels at a depth of 0.5 m. Average As content near the pole on all study sites was three to eight times higher than Quebec's Level C criterion (50 mg kg(-1)), although it dropped to 31 mg kg(-1) at 0.1 m. Results also showed that As persisted up to 1 m in soil depth (17-54 mg kg(-1)). Copper and Cr concentrations in ground water samples were always <1.000 mg L(-1) and <0.05 mg L(-1), respectively and Cr(VI) was <0.02 mg L(-1). One sample contained an As concentration >0.025 mg L(-1) but bioassays showed that, overall, ground water had a low ecotoxic potential.     

Solubilization of manganese and trace metals in soils affected by acid mine runoff

Manganese solubility has become a primary concern in the soils and water supplies in the Alamosa River basin, Colorado due to both crop toxicity problems and concentrations that exceed water quality standards. Some of the land in this region has received inputs of acid and trace metals as a result of irrigation with water affected by acid mine drainage and naturally occurring acid mineral seeps. The release of Mn, Zn, Ni, and Cu following saturation with water was studied in four soils from the Alamosa River basin. Redox potentials decreased to values adequate for dissolution of Mn oxides within 24 h following saturation. Soluble Mn concentrations were increased to levels exceeding water quality standards within 84 h. Soluble concentrations of Zn and Ni correlated positively with Mn following reduction for all four soils studied. The correlation between Cu and Mn was significant for only one of the soils studied. The soluble concentrations of Zn and Ni were greater than predicted based on the content of each of these metals in the Mn oxide fraction only. Increases in total electrolyte concentration during reduction indicate that this may be the result of displacement of exchangeable metals by Mn following reductive dissolution of Mn oxides.     

DISSOLVED HEAVY METALS IN SHALLOW GROUND WATER IN A SOUTHEASTERN MICHIGAN URBAN WATERSHED1

ABSTRACT: The occurrence of dissolved heavy metal concentrations in shallow ground water were measured at 126 sites within an urban watershed in southeastern Michigan. A total of 1,140 samples were collected from the first saturated zone, and the mean concentrations of 11 heavy metals (arsenic, barium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, and zinc) were obtained and compared to their corresponding mean concentrations within surface soil. The results suggest that former and current land use processes have resulted in significant adverse impacts on the study region. Levels of Cr 20 to 30 times the maximum contaminant level (MCL) have been detected in the ground water beneath industrial sites. In addition, Cd and Pb have been found at levels exceeding their MCLs where surface soils are clay‐rich, and in sandy soils at more than 10 times their MCLs. The high levels of Cr in ground water strongly suggest that the chromium is in a hexavalent form, and this likelihood is supported by current studies. Given the hydraulic connection between the watershed's surface waters and the Great Lakes, these findings raise significant ecological and public health concerns.     

Prediction of zinc, cadmium, lead, and copper availability to wheat in contaminated soils using chemical speciation, diffusive gradients in thin films, extraction, and isotopic dilution techniques

To predict the availability of metals to plants, it is important to understand both solution- and solid-phase processes in the soil, including the kinetics of metal release from its binding agent (ligand and/or particle). The present study examined the speciation and availability of Zn, Cd, Pb, and Cu in a range of well-equilibrated metal-contaminated soils from diverse sources using several techniques as a basis for predicting metal uptake by plants. Wheat (Triticum aestivum L.) was grown in 13 metal-contaminated soils and metal tissue concentrations (Zn, Cd, Pb, and Cu) in plant shoots were compared with total soil metal concentrations, total soluble metal, and free metal activities (pM2+) in soil pore waters, 0.01 M CaCl2-extractable metal concentrations, E values measured by isotope dilution, and effective metal concentrations, C(E), measured by diffusive gradients in thin films (DGT). In the DGT technique, ions are dynamically removed by their diffusion through a gel to a binding resin, while E values represent the isotopically exchangeable (labile) metal pools. Free metal activities (Zn2+, Cd2+, and Pb2+) in soil pore waters were determined using a Donnan dialysis technique. Plant Zn and Cd concentrations were highly related to C(E), while relationships for Zn and Cd with respect to the other measures of metals in the soils were generally lower, except for CaCl2-extractable Cd. These results suggest that the kinetically labile solid-phase pool of metal, which is included in the DGT measurement, played an important role in Zn and Cd uptake by wheat along with the labile metal in soil solution. Plant Pb concentrations were highly related to both soil pore water concentrations and C(E), indicating that supply from the solid phase may not be so important for Pb. Predictions of Cu uptake by wheat from these soils by the various measures of Cu were generally poor, except surprisingly for total Cu.     

Dissolution and transport of TNT, RDX, and composition B in saturated soil columns

Low-order detonations and blow-in-place procedures on military training ranges can result in residual solid explosive formulations to serve as distributed point sources for ground water contamination. This study was conducted to determine if distribution coefficients from batch studies and transport parameters of pure compounds in solution adequately describe explosive transport where compounds are present as solid particles in formulations. Saturated column transport experiments were conducted with 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and the explosive formulation, Composition B (Comp B) (59.5 +/- 2.0% RDX, 39.5 +/- 2.3% TNT, and 1% wax) in solid and dissolved forms. The two soils used were Plymouth loamy sand (mesic, coated Typic Quartzipsamments) from Camp Edwards, MA and Adler silt loam (coarse-silty, mixed, superactive, thermic Fluvaquentic Eutrudepts) from Vicksburg, MS. Interrupted flow experiments were used to determine if explosives were at equilibrium distribution between soil and solution phases. The HYDRUS-1D code was used to determine fate and transport parameters. Results indicated that sorption of high explosives was rate limited. The behavior of dissolved Comp B was similar to the behavior of pure TNT and RDX. Behavior of solid Comp B was controlled by dissolution that depended on physical properties of the Comp B sample. Adsorption coefficients determined by HYDRUS-1D were different from those determined in batch tests for the same soils. Use of parameters specific to formulations will improve fate and transport predictions.     

Fate of biosolids trace metals in a dryland wheat agroecosystem

Biosolids land application for beneficial reuse applies varying amounts of trace metals to soils. Measuring plant-available or total soil metals is typically performed to ensure environmental protection, but these techniques do not quantify which soil phases play important roles in terms of metal release or attenuation. This study assessed the distribution of Cd, Cr, Cu, Mo, Ni, Pb, and Zn associated with soluble/exchangeable, specifically adsorbed/carbonate-bound, amorphous Mn hydroxyoxide-bound, amorphous Fe hydroxyoxide-bound, organically complexed, and residual inorganic phases. Biosolids were applied every 2 yr from 1982 to 2002 (except in 1998) at rates of 0, 6.7, 13.4, 26.8, and 40.3 dry Mg biosolids ha(-)(1) to 3.6- by 17.1-m plots. In 2003, 0- to 20-cm and 20- to 60-cm soil depths were collected and subjected to 4 mol L(-1) HNO(3) digestion and sequential extraction. Trace metals were concentrated in the 0- to 20-cm depth, with no significant observable downward movement using 4 mol L(-1) HNO(3) or sequential extraction. The sequential extraction showed nearly all measurable Cd present in relatively mobile forms and Cr, Cu, Mo, Ni, Pb, and Zn present in more resistant phases. Biosolids application did not affect Cd or Cr fractionation but did increase relatively immobile Cu, Mo, and Zn phases and relatively mobile Cu, Ni, and Pb pools. The mobile phases have not contributed to significant downward metal movement. Long-term, repeated biosolids applications at rates considered several times greater than agronomic levels should not significantly contribute to downward metal transport and ground water contamination for soils under similar climatic conditions, agronomic practices, and histories.     

Total Contents and Sequential Extraction of Heavy Metals in Soils Irrigated with Wastewater,Akaki, Ethiopia

The Akaki River, laden with untreated wastes from domestic, industrial, and commercial sources, serves as a source of water for irrigating vegetable farms. The purpose of this study is to identify the impact of waste-water irrigation on the level of heavy metals and to predict their potential mobility and bioavailability. Zn and V had the highest, whereas Hg the lowest, concentrations observed in the soils. The average contents of As, Co, Cr, Cu, Ni, Zn, V, and Hg of both soils; and Pb and Se from Fluvisol surpassed the mean + 2 SD of the corresponding levels reported for their uncontaminated counterparts. Apparently, irrigation with waste water for the last few decades has contributed to the observed higher concentrations of the above elements in the study soils (Vertisol and Fluvisol) when compared to uncontaminated Vertisol and Fluvisol. On the other hand, Vertisol accommodated comparatively higher average levels of Cr, Cu, Ni, Zn, etc V, and Cd, whereas high contents of Pb and Se were observed in Fluvisol. Alternatively, comparable levels of Co and Hg were found in either soil. Except for Ni, Cr, and Cd in contaminated Vertisol, heavy metals in the soils were not significantly affected by the depth (0–20 and 30–50 cm). When the same element from the two soils was compared, the levels of Cr, Cu, Ni, Pb, Se, Zn, V, Cd at 0–20 cm; and Cr, Ni, Cu, Cd, and Zn at 30–50 cm were significantly different. Organic carbon (in both soils), CEC (Fluvisol), and clay (Vertisol) exhibited significant positive correspondences with the total heavy metal levels. Conversely, Se and Hg contents revealed perceptible associations with carbonate and pH. The exchangeable fraction was dominated by Hg and Cd, whereas the carbonate fraction was abounded with Cd, Pb, and Co. conversely, V and Pb displayed strong affinity to reducible fraction, where as Cr, Cu, Zn, and Ni dominated the oxidizable fraction. Cr, Hg, Se, and Zn (in both soils) showed preference to the residual fraction. Generally, a considerable proportion of the total levels of many of the heavy metals resided in non residual fractions. The enhanced lability is generally expected to follow the order: Cd > Co > Pb > Cu > Ni > Se > V and Pb > Cd > Co > Cu > Ni > Zn in Vertisol and Fluvisol, respectively. For the similar wastewater application, the soil variables influence the status and the distribution of the associated heavy metals among the different soil fractions in the study soils. Among heavy metals that presented relatively elevated levels and with potential mobility, Co, Cu, Ni (either soil), V (Vertisol), Pb, and Zn (Fluvisol) could pose health threat through their introduction into the food chain in the wastewater irrigated soils.     

Fate of pesticides in tropical soils of Brazil under field conditions

The potential of pesticides for nonpoint ground water pollution depends on their dissipation and leaching behavior in soils. We investigated the fate of 10 pesticides in two tropical soils of contrasting texture in the Brazilian Cerrado region near Cuiabá during an 80-d period, employing topsoil dissipation studies, soil core analyses, and lysimeter experiments. Dissipation of pesticides was rapid, with field half-lives ranging from 0.8 to 20 d in Ustox and 0.6 to 11.8 d in Psamments soils. Soil core analyses showed progressive leaching of polar pesticides in Psamments, whereas in Ustox pesticides were rapidly transported to 40 cm soil depth regardless of their sorption properties, suggesting that leaching was caused by preferential flow. In lysimeter experiments (35 cm soil depth), cumulative leaching was generally low, with < or = 0.02% and < or = 0.19% of the applied amounts leached in Ustox and Psamments, respectively. In both soils, all pesticides but the pyrethroids were detected in percolate at 35 cm soil depth within the first 6 d after application. Cumulative efflux and mean concentrations of pesticides in percolate were dosely correlated with their Groundwater Ubiquity Score (GUS). The presence of alachlor (2-chloro-2', 6'-diethyl-N-methoxymethylacetanilide), atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine), metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl)acetamide], simazine [2-chloro-4,6-bis(ethylamino)-1,3,5-triazine], and trifluralin (2,6-dinitro-N,N-dipropyl-4-trifluoromethylaniline) throughout the soil profile and in percolate of wick lysimeters at 95 cm soil depth indicated that a nonpoint pollution of ground water resources in tropical Brazil cannot be ruled out for these substances.     

Solution chemistry influence on metal mobility in biosolids-amended soils

Many studies have implicated dissolved organic carbon (DOC) as an important contributor to the elevated mobility of trace metals in soils amended with biosolids. Few of these studies, however, have quantified both DOC and metal concentrations. We completed laboratory leaching column studies on a dryland Platner loam (fine, smectitic, mesic Aridic Paleustoll) and an irrigated Osgood sand (loamy, mixed, mesic Arenic Ustollic Haplargid), both with a history of biosolids application. The soils were neutral to slightly alkaline in pH prior to amendment. We performed an additional application of biosolids to one set of columns in the laboratory at a rate of 28 Mg ha(-1) to investigate the effect of time following application on metal mobility. The effect of electrolyte concentration was studied by using both distilled water and simulated irrigation water. Biosolids application increased both DOC and Cu in the column effluents resulting in a positive correlation between Cu and DOC across application treatments for both soils. Both Cu and Pb were mobilized under conditions of low electrical conductivity (EC). This may be the result of the release of a strong metal-binding component of DOC under these conditions. Conversely, Zn mobility was positively correlated with EC, suggesting that either cation exchange or the formation of inorganic complexes influences Zn mobility. Anodic stripping voltammetry measurements indicated that only a small percentage of the total dissolved metals existed as free ions or inorganic complexes; the remainder appears to be complexed to DOC.     

Assessment of the use of industrial by-products to remediate a copper- and arsenic-contaminated soil

Two water treatment sludges (WTS-A, WTS-B), two red muds (RM), and red gypsum (RG), all rich in iron oxy-hydroxides, were added to a soil highly polluted with As and Cu at 2% (w/w) to reduce metal bioavailability. Because the amendments increased soil pH to approximately 6, a lime treatment to the same pH and an unamended treatment were included for comparison. All the amendments had significant positive effects on the soil microbial biomass and growth of ryegrass (Lolium multiflorum Lam. cv. Avance), but only WTS-A improved lettuce (Lactuca sativa L. cv. Tom Thumb) growth. The mineralization of added ammonium nitrogen was not significantly affected by the treatments, while a physiologically based extraction test (PBET) showed that bioaccessibility of As was low (< 5%) and decreased only in the WTS-A treatment. Concentrations of As in soil pore water and extractable As only decreased in the WTS and RG treatments. In contrast, Cu concentrations in soil pore water and extractable Cu decreased in all treatments, by more than 84% in the WTS, RM, and RG treatments. Non-isotopically exchangeable As and Cu were present in colloids in the soil pore water. Untreated soil had < 4% isotopically exchangeable As and this decreased by approximately 50%, with WTS, RM, and RG. The labile Cu pool represented a large proportion (34%) of the total Cu pool, and the isotopically exchangeable and soluble Cu were strongly correlated with soil pH. Acidification of the treated soils showed that the labile As and Cu both increased in the treated soils compared with untreated soils. The significance of the treatment effects on soil fertility and potential off-site transport of As and Cu to ground water are discussed.     

Assessment of contamination from arsenical pesticide use on orchards in the Great Valley region, Virginia and West Virginia, USA

Lead arsenate pesticides were widely used in apple orchards from 1925 to 1955. Soils from historic orchards in four counties in Virginia and West Virginia contained elevated concentrations of As and Pb, consistent with an arsenical pesticide source. Arsenic concentrations in approximately 50% of the orchard site soils and approximately 1% of reference site soils exceed the USEPA Preliminary Remediation Goal (PRG) screening guideline of 22 mg kg(-1) for As in residential soil, defined on the basis of combined chronic exposure risk. Approximately 5% of orchard site soils exceed the USEPA PRG for Pb of 400 mg kg(-1) in residential soil; no reference site soils sampled exceed this value. A variety of statistical methods were used to characterize the occurrence, distribution, and dispersion of arsenical pesticide residues in soils, stream sediments, and ground waters relative to landscape features and likely background conditions. Concentrations of Zn, Pb, and Cu were most strongly associated with high developed land density and population density, whereas elevated concentrations of As were weakly correlated with high orchard density, consistent with a pesticide residue source. Arsenic concentrations in ground water wells in the region are generally <0.005 mg L(-1). There was no spatial association between As concentrations in ground water and proximity to orchards. Arsenic had limited mobility into ground water from surface soils contaminated with arsenical pesticide residues at concentrations typically found in orchards.     

Copper lability in soils subjected to intermittent submergence

Reducing conditions in soils can have significant influences on the availability of nutrient and toxic metals, through their remobilization, their release through reductive dissolution of oxide phases, and from the formation of precipitates. In the literature, contrasting results are reported on the effects of temporary waterlogging conditions on the availability of metals. In the present study, changes in the "labile" or "potentially available" pool of copper (Cu) in soils as a consequence of up to three intermittent soil submergence cycles was investigated using isotopic dilution. The soils (an Oxisol and an Inceprisol) selected were amended in the field with both biosolids-Cu and salt-Cu. Intermittent soil submergence was found to have a significant effect on the lability of Cu in soils, with E(total) values generally increasing in all the treatments with the different submergence cycles, the highest lability of Cu observed in the Cu-salt treatment. The presence of nonexchangeable colloidal forms of Cu, influenced by treatments and submergence cycles, was also reported.     

Solubility of phosphorus and heavy metals in potting media amended with yard waste-biosolids compost

The potential risk of surface and ground water contamination by phosphorus (P) and heavy metals leached from compost-based containerized media has become an environmental concern. Solubility and fractionation of P and heavy metals were evaluated in media containing 0, 25, 50, 75, or 100% compost derived from biosolids and yard trimmings for potential impacts on the environment. As compost proportion in peat-based media increased from 0 to 100%, concentrations of total P, Cd, Cu, Ni, Pb, Zn, and Mn in the media increased whereas concentrations of total Co and Cr decreased. Except for Cu, all heavy metals in the water-soluble fraction decreased with increasing compost proportion in the media, because of higher Fe, Al, and Ca concentrations and pH values of the composts than the peat. When the media pH is controlled and maintained at normal range of plant growth (5.5-6.5), leaching of the heavy metals is minimal. Incorporation of compost to the peat-based media also decreased the proportion of total P that was water-soluble. However, concentrations of bioavailable inorganic phosphorus (NaHCO3-IP), readily mineralizable organic phosphorus (NaHCO3-OP), potentially bioavailable inorganic phosphorus (NaOH-IP), and potentially bioavailable organic phosphorus (NaOH-OP) were still higher in the media amended with compost because of higher total P concentration in the compost. Further study is needed to verify if less or no topdressing of chemical P fertilizer should be applied to the compost-amended media to minimize P effect on the environment when compost-amended potting media are used for nursery or greenhouse crop production systems.     

Potential risks of copper, zinc, and cadmium pollution due to pig manure application in a soil-rice system under intensive farming: a case study of Nanhu, China

Heavy metal (copper [Cu], zinc [Zn], and cadmium [Cd]) pollution of soils from pig manures in soil-rice ( L.) systems under intensive farming was investigated, taking Nanhu, China, as the case study area. Two hundred pig manures and 154 rice straws, brown rice samples, and corresponding surface soil (0-15 cm) samples were collected in paddy fields from 150 farms in 16 major villages within the study area. The mean Cu and Zn concentrations in pig manures consistently exceeded the related standard. About 44 and 60% of soil samples exceed the Chinese Soil Cu and Cd Environmental Quality Standards, respectively. The concentration of Cu, Zn, and Cd in brown rice did not exceed the Chinese Food Hygiene Standard. There was a significant positive correlation between total Cu and Zn contents in soil and application rate of pig manures. Strong correlation was observed between the extractable Cu, Zn, and Cd in soil and the Cu, Zn, and Cd contents in the brown rice. The spatial distribution maps of Cu and Zn concentrations in brown rice, straw, and extractable soil Cu and Zn concentration also showed similar geographical trends. Further analyses on heavy metals loading flux and accumulation rates from pig manure applied suggested that Cu and Cd contents in soil currently have already exceeded the maximum permissible limit, and Zn, if still at current manure application rates, will reach the ceiling concentration limits in 9 yr. This study assists in understanding the risk of heavy metals accumulating from pig manure applications to agricultural soils.     

The characterization of total and leachable metals in foundry molding sands

Waste molding sands from the foundry industry have been successfully used as a component in manufactured soils, but concern over metal contamination must be addressed before many states will consider this beneficial use. Since there is little data available on this topic, the purpose of this study was to characterize total and leachable metals from waste molding sands. A total elemental analysis for Ag, Al, As, B, Ba, Be, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Sb, V, and Zn was conducted on 36 clay-bonded and seven chemically bonded molding sands. Total metal concentrations in the molding sands were similar to those found in agricultural soils. The leaching of metals (i.e. Ag, As, Ba, Be, Cd, Cr, Cu, Ni, Pb, Sb, and Zn) was assessed via the toxicity characteristic leaching procedure (TCLP), synthetic precipitation leaching procedure (SPLP), and ASTM water leach test. Based on the TCLP data, none of the 43 molding sands would meet the Resource Conservation and Recovery Act (RCRA) characteristic for toxicity due to high Ag, As, Ba, Cd, Cr, and Pb. Compared to the TCLP results, the metal concentrations were generally lower in the SPLP and ASTM extracts, which is likely related to the buffering capacity of the extraction fluids.     

Accelerated weathering of biosolid-amended copper mine tailings

Application of municipal biosolids to mine tailings can enhance revegetation success, but may cause adverse environmental impacts, such as increased leaching of NO3- and metals to ground water. Kinetic weathering cells were used to simulate geochemical weathering to determine the effects of biosolid amendment on (i) pH of leachate and tailings, (ii) leaching of NO3- and SO4(2-), (iii) leaching and bioavailability (DTPA-extractable) of selected metals, and (iv) changes in tailing mineralogy. Four Cu mine tailings from southern Arizona differing in initial pH (3.3-7.3) and degree of weathering were packed into triplicate weathering cells and were unamended and amended with two rates (equivalent to 134 and 200 Mg dry matter ha(-1)) of biosolids. Biosolid application to acid (pH 3.3) tailings resulted in pH values as high as 6.3 and leachate pH as high as 5.7, and biosolids applied to circumneutral tailings resulted in no change in tailing or leachate pH. Concentrations of NO3--N of up to 23 mg L(-1) occurred in leachates from circumneutral tailings. The low pH of the acidic tailing apparently inhibited nitrification, resulting in leachate NO3--N of <5 mg L(-1). Less SO4(2-)-S was leached in biosolid-amended versus unamended acid tailings (final rate of 0.04 compared with 0.11 g SO4(2-)-S wk(-1)). Copper concentrations in leachates from acidic tailings were reduced from 53 to 27 mg L(-1) with biosolid amendment. Copper and As concentrations increased slightly in leachates from biosolid-amended circumneutral tailings. Small increases in DTPA-extractable Cu, Ni, and Zn occurred in all tailings with increased biosolid rate. Overall, there was little evidence of potential for adverse environmental impacts resulting from biosolid application to these Cu mine tailings.     

RDX loss in a surface soil under saturated and well drained conditions

On military training ranges, low-order, incomplete detonations deposit RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine) into surface soils. In this study, we evaluated RDX biodegradation in surface soils obtained from a military training range in Alaska. Two factors were compared: (i) soil water potential during the incubations; and (ii) the use of acetonitrile (ACN) as an RDX carrier to spike samples. Organic solvents have been used in laboratory studies to dissolve slightly water-soluble contaminants before addition to soil. We added ACN to obtain final soil ACN concentrations of 0 mg kg(-1) (0%), 1000 mg kg(-1) (0.1%) and 10 000 mg kg(-1) (1%). We then compared RDX attenuation in the soil under saturated and unsaturated conditions. RDX fell below the limit of detection within 3 wk of study initiation under the saturated condition. A maximum degradation rate of 0.15 mg RDX L(-1) d(-1) was measured. Under the unsaturated condition, 42% of the original RDX was still present at study termination (5 wk). The addition of acetonitrile at 0.1 or 1.0% had no affect on RDX loss in the saturated soil. In the unsaturated soil, however, ACN at 1.0% inhibited RDX loss by as much as 25%. These findings indicate that soil water potential and carrier solvent concentrations can impact the rate and extent to which RDX is attenuated in a surface soil.