3—（H—酸偶氮）—4—（羟基）—苯磺酸与铁显色反应研究应用

研究了新试剂３—（Ｈ—酸偶氮）—４—（羟基）—苯磺酸（ＨＡＨＢＳ）与铁的显色反应,在ＮＨ４Ａｃ（ｐＨ＝ ７．０）缓冲介质中,ＨＡＨＢＳ和Ｆｅ（Ⅲ）可生成３∶１ 稳定络合物,λｍａｘ ＝ ５５０ ｎｍ ,ε＝ ４．８９×１０４Ｌ·ｍ ｏｌ－ １·ｃｍ － １,铁含量在０～０．６ ｍ ｇ／Ｌ内符合比耳定律。方法用于环境水样中铁的测定,结果令人满意。     

N─苯甲酰苯基羟胺／吡啶偶氮染料配体交换反应萃取分光光度法测定固体废物浸出液中的微量钒

在强酸性介质中，ＶＯ３与Ｎ－苯甲酰苯基羟胺（ＢＰＨＡ）反应生成紫红色络合物，能定量地被ＣＨＣＬ３萃取．萃取液加入２－（５－溴－２－吡啶偶氮）－５－二乙氨基酚（５—Ｂｒ—ＰＡＤＡＰ）后可发生配体交换反应，并生成橙红色的Ｖ（Ｖ）－５—Ｂｒ—ＰＡＤＡＰ络合物，有机相可直接用于光度测定．Ｖ（Ｖ）－５—Ｂｒ－ＰＡＤＡＰ的最大吸收波长为６００ｎｍ，摩尔吸光系数为５．４Ｘ１０￣４Ｌ·ｍｏｌ－１·ｃｍ－１，线性范围为０～０．７６μｇｖ／ｗｌ。     

5－Cl－PADAB－SDS分光光度法连续测定血清及废水中的铜和铁

在十二烷基硫酸钠，氟化钠和盐酸羟胺存在下，ＰＨ＝５．２～７醋酸－醋酸钠缓冲溶液中，Ｃｕ（Ⅱ），Ｆｅ（Ⅱ）分别与５－ＣＩ－ＰＡＤＡＢ形成紫红色络合物。选择测定波长为５３０ｎｍ，铜和铁的摩尔吸光系数分别为５２×１０４Ｌ·ｍｏｌ－１·ｃｍ－１，６０×１０４Ｌ·ｍｏｌ－１·Ｃｍ－１．铜和铁分别在０～１２ｕｇ／１０ｍｌ和０～１０ｕｇ／１０ｍ１范围内符合比尔定律。选用了硫代硫酸钠－硫脲褪色液和ＥＤＴＡ掩蔽剂，直接用于血清及水中铜和铁的连续测定，结果满意。     

二安替比林─（2，4─二羟基）苯基甲烷光度法测定铬（Ⅵ）

合成了二安替比林基─（２，４─二羟基）苯基甲烷（ＤＡＤＨＭ）．在Ｍｎ（Ⅱ）和吐温─２０存在下．Ｃｒ（Ⅵ）与ＤＡＤＨＭ反应生成有色化合物．λｍａｘ为４６０ｎｍ，ε＝１．１×１０５Ｌ·ｍｏｌ－１·ｃｍ－１，Ｃｒ（Ⅵ１）量在０～１０μｇ／２５ｍｌ范围内符合比耳定律。该体系灵敏度较高，选择性较好．用于水和废水中微量铬（Ⅵ）的测定，结果满意。     

二安替比林苯基甲烷光度法测锰的研究

研究了二安替比林苯基甲烷（ Ｄ Ａ Ｍ Ｍ ）与锰（Ⅳ）的显色反应条件,在磷酸介质中, Ｃｕ（Ⅱ）存在下, Ｄ Ａ Ｍ Ｍ 与 Ｍ ｎ（Ⅳ）反应生成橙色产物,λｍ ａｘ＝ ４８５ ｎｍ ,ε＝ ３．３２×１０４ Ｌ·ｍ ｏｌ－ １·ｃｍ － １,锰含量在００８～１ｍ ｇ／ Ｌ符合比耳定律。用于废水和不经分离直接用于铝合金中锰的测定,结果满意。     

新试剂4－（2－喹啉偶氮）－1，3－二羟萘分光光度法测定水中镉

研究了镉（Ⅱ）与４－（２－喹啉偶氮）－１，３－二羟萘（２－ＱＡＤＶＭ）的显色反应。结果表明：在０．３ｍｎｏｌ／Ｌ氢氧化钠溶液中，当有十二烷基（２－羟乙基）二甲基氯化铵（ＤＥＭＡＣ）存在时，镉（Ⅱ）与２－喹啉偶氮形成１：２橙红色络合物，λ_ｍａｘ为５１０_ｎｍ，摩尔吸光系数ε＝１．２×１０５Ｌ·ｍｏｌ－１·ｃｍ－１，镉的浓度的在０～２０μｇ／（２５ｍＬ）范围内符合比尔定律，用２－喹啉偶氮作显色剂，可直接测定废水中的镉。试样用标准加入法测得回收率为９６％～１０４％，相对标准偏差小于３％，用此法与双硫腙分光光度法对模拟镀镉废水进行了对比试验，其相对误差小于４％。     

巯基棉富集分离铜试剂─吐温─80—OP水相光度法测定水中微量铜

研究了在非离子表面活性剂吐温－８０和乳化剂ＯＰ存在下，于ｐＨ８．５缓冲介质中，铜（Ⅱ）与铜试剂显色反应条件。结果表明：配合物的最大吸收波长为４５３ｎｍ，表观摩尔吸光系数为１．５４×１０４Ｌ·ｍｏｌ－１．ｃｍ－１，铜（Ⅱ）含量在０～７０μｇ／２５ｍｌ范围内符合比耳定律。该法与巯基棉富集分离相结合，应用于天然水及废水中微量铜的测定，结果满意。     

DDTC—TX—100胶束增溶直接光度法测定水中低含量铜

ＴｒｉｔｏｎＸ１００对ＤＤＴＣ（二乙基二硫代氨基甲酸钠）与铜反应生成的络合物Ｃｕ（ＤＤＴＣ）２有增溶增敏作用,建立了低含量铜直接光度测定法。操作简便快速,选择性、精密度和回收率均较好,相对标准偏差为０８％～４３％,回收率为９６％～１０６％,摩尔吸光系数ε＝６４×１０３Ｌ／（ｍｏｌ·ｃｍ     

异相平衡流动注射分光光度法测定水中痕量SO^2—4

根据异相平衡的原理,确立了用流动注射分光光度法测定水样中痕量ＳＯ＾２－４的新方法。利用Ｂａ（Ⅱ）与偶氮氯磷Ⅲ的二元络合显色反应及ＢａＳＯ４＝Ｂａ＾２＋＋ＳＯ＾２－４进入微溶化合物ＢａＳＯ４反应柱前后吸光值的改变,从而求得ＳＯ＾２－浓度。表观摩尔吸光系数ε＝２．３＊１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１,ＳＯ＾２－４检的线性范围为０－４０ｍｇ／Ｌ,检测限为０．８０ｍｇ／Ｌ,相对标准偏差为１．２％,试     

高效液膜分离富集测定微量铜

应用高效乳状液膜技术分离、富集水和土壤样品中微量铜（Ⅱ）．研究了流动载体（Ｐ２０４）、表面活性剂（ＳＰａｎ８０）、膜的增强剂（液体石蜡）、膜溶剂（煤油）和内相解吸剂（２．５ｍｏｌ／ＬＨ２ＳＯ４）等液膜体系，对分离富集微量铜（Ⅱ）的影响．确定了Ｓｐａｎ８０—Ｐ２０４─液体石蜡─煤油─Ｈ２ＳＯ４高效液膜体系的最佳组成和最适宜的实验条件．富集后的溶液用１－（２－吡啶偶氮）－２－萘酚（ＰＡＮ）分光光度法测定铜（Ⅱ）．用本法富集水和土壤中微铜（Ⅱ）．回收率在９９％以上。应用于测定水和土壤中的微量铜．相对标准偏差为１．２％～４．５％。     

IC色谱仪电位法测定S^2—的运用与研究

介绍了应用ＹＩＣ－８型离子色谱仪电化学检测器测定标准样品及废水样中Ｓ＾２－的含量，同时与化学法进行比较，肯定了电位法的准确性、可靠性。     

Determination of copper in biological samples by flame atomic absorption spectrometry after precipitation with Me-BTAP

A simple and sensitive method was developed for determination of trace copper by direct precipitation preconcentration and detection with Flame Atomic Absorption Spectrometry (FAAS). The reagent 2-[2'-(6-methyl-benzothiazolylazo)]-4-aminophenol (Me-BTAP) was used as precipitating agent. The experimental conditions for the quantitative precipitation of copper, such as pH, amount of reagents, temperature and the effect of diverse ions on the precipitation have been investigated. It was found that copper is quantitatively extracted (> or =95%) and the method provides a sensitivity enhancement of 40-fold for a 10 ml sample volume with a detection limit of 0.5 microg l(-1). The proposed method was successfully applied for the determination of trace copper in water, urine and biological samples.     

Study on determination of iron,cobalt, nickel,copper, zinc and manganese in drinking water by solid-phase extraction and RP-HPLC with 2-(2-quinolinylazo)-5-diethylaminophenol as precolumn derivatizing reagent

A new method for the determination of iron, cobalt, nickel, copper, zinc and manganese in drinking water by the reversed-phase high-performance liquid chromatography (RP-HPLC) with 2-(2-quinolinylazo)-5-diethylaminophenol (QADEAP) as precolumn derivatizing reagent was studied in this paper. The iron, cobalt, nickel, copper, zinc, and manganese ions react with QADEAP to form color chelates in the presence of cetyl trimethylammonium bromide (CTMAB) and acetic acid-sodium acetic buffer solution medium of pH 4.0. These chelates were enriched by solid-phase extraction with a Waters Nova-Pak C18 cartridge and eluted the retained chelates from the cartridge with tetrahydrofuran (THF). The enrichment factor of 100 was achieved. Then the chelates were separated on a Waters Nova-Pak C18 column (3.9 x 150 mm, 5 microm) by gradient elution with methanol (containing 0.2% of acetic acid and 0.1% of CTMAB) and 0.05 mol L(-1) acetic acid-sodium acetic buffer solution (containing 0.1% of CTMAB) (pH 4.0) as mobile phase at a flow rate of 0.5 ml min(-1), and monitored with a photodiode array detector from 450 approximately 700 nm. The detection limits (S/N = 3) of iron, cobalt, nickel, copper, zinc and manganese are 0.8, 1.1, 0.9, 1.1, 1.5 and 2.0 ng L(-1), respectively, in the original sample. This method can be applied to determination at the microg L(-1) level of iron, cobalt, nickel, copper, zinc and manganese in drinking water with good results.     

伊犁河水质中CODCr和CODMn的相关性探讨

对伊犁河水质中CODCr与CODMn的相关性进行了讨论。     

库仑滴定法测定化学需氧量的可靠性研究

通过对库仑滴定法测定废水中化学需氧量存在的问题分析,提出相应解决办法,加强空白值式剂,器皿使用过程中的纯净;注重废水稀释倍数的影响。这些措施为快速ＣＯＤｃｒ值的可靠性提供了保证。     

CODCr测定方法探讨

对经典测定水样ＣＯＤＣｒ的方法进行了改进,以硫酸银－硫酸铜作催化剂代替单独作用硫酸银,用适量硝酸银、硝酸铋代替硫酸汞消除氯离子的干扰,适当提高了消解用硫酸浓度,缩短回流时间。     

Catalytic hydrodechlorination of 1,2-dichloroethane using copper nanoparticles under reduction conditions of sodium borohydride

1,2-Dichloroethane (1,2-DCA) is a raw material used for the manufacture of vinyl chloride monomer (VCM) and therefore has very often been detected in the groundwater nearby the VCM manufacturing plant. Zero-valent iron (ZVI) is capable of degrading a wide array of highly chlorinated contaminants; however, the reactivity of ZVI towards 1,2-DCA is very low. In this study, zero-valent copper nanoparticles have been synthesized for effective dechlorination of 1,2-DCA under reduction conditions of sodium borohydride. Copper nanoparticles consisted of mainly metallic copper (Cu(0)) with small amounts of cuprous oxide (Cu(2)O). They have surface areas of about 19.0 m(2) g(-1) and an average diameter of 15 nm. Batch experiments were conducted to test the effectiveness of copper nanoparticles for 1,2-DCA degradation using sodium borohydride as electron donors where the ORP was measured as -1100 mV. More than 80% of 1,2-DCA (30 mg L(-1)) was rapidly degraded within 2 h in the presence of both copper nanoparticles (2.5 g L(-1)) and borohydride (25 mM). No reduction of 1,2-DCA was observed when the system contained either copper nanoparticles alone or borohydride alone. The degradation intermediates included ethane and ethylene accounting for 79% and ～1.5% of the 1,2-DCA lost, respectively. Potential environmental applications can be achieved by immobilizing copper nanoparticles onto the surface of reducing metals to form a reactive bimetallic structure.     

Copper leaching from brake wear debris in standard extraction solutions

Quantification of the copper content of and copper leaching from a disc brake wear debris sample was performed using microwave-assisted acid digestion, the Federal Toxicity Characteristic Leaching Procedure (TCLP), and the State of California Waste Extraction Test (WET). The brake wear debris tested was a composite sample obtained from a brake dynamometer test of one brake pad source material. Comparative digestion studies demonstrated that a modified aqua regia matrix (HNO3:HCl:H2O2 = 1:3:0.5) optimized the digestion effectiveness for determining the total copper content in the brake wear debris. No significant sample heterogeneity within the brake wear debris was observed, based on statistically indistinguishable total copper content results for subsamples with a wide range of sample masses. Upon pooling all subsample results, an overall total copper content for the composite brake wear debris sample was determined to be 10.8% (g/g), with a 95% confidence limit of +/- 0.5% (g/g). Copper leaching increased with decreasing solid-to-liquid ratios in TCLP tests, but was unaffected by the solid-to-liquid ratio in the WET. For a 1:10(4) (g/g) solid-to-liquid ratio, 85% and 99% of the total mass of copper present in the composite brake wear debris sample was leached into solution during the TCLP and WET, respectively. Rate studies also demonstrated that the WET resulted in a faster rate and higher extent of copper leaching relative to the TCLP. Compared to reference copper-containing materials, the composite brake wear debris sample exhibited relatively higher TCLP and WET copper leaching characteristics. The higher copper leaching exhibited by the brake wear debris sample may have resulted from its higher specific surface area and/or from changes in the chemical form of copper that occurred during the braking process.     

投菌水解（酸化）—生物接触氧化—混凝法处理酵母生产废水

研究了采用投菌水解（酸化）－生物接触氧化－浊凝化处理酵母生产废水。试验结果表明，进水浓度控制在ＣＯＤＣｒ值５０００ｍｇ／Ｌ左右，生化系统可取得较高的处理效率；生经处理出水再以碱式 化铝为混凝剂，聚丙烯酰胺为助凝剂进行混凝处理，其出水ＣＯＤＣｒ值可控制在２００ｍｇ／Ｌ以下，并且可部分回流使用。     

浅谈TOC与CODCr的关系

介绍了TOC和CODCr的含义，比较了TOC与CODCr测定方法、使用仪器的不同和各自的优缺点，并从理论上和实际水样测定中论述了TOC和CODCr的相关性。对于不同的废水，TOC 与CODCr的相关性不一样，必须先实验求出二者之间的关系。