A new catalytic-spectrophotometric method for quantification of trace amounts of nitrite in fruit juice samples

A new kinetic method has been developed for the determination of nitrite in fruit juice samples. The method is based on the catalytic effect of nitrite with the oxidation of Nile Blue A (NBA) by KBrO₃ in the sulfuric acid medium. The optimum conditions obtained are 1.2 mM sulfuric acid, 0.034 mM of NBA, 2.8?×?10^?3 M KBrO₃, reaction temperature of 20 °C, and reaction time of 100 s at 595.5 nm. Under the optimized conditions, the method allowed the quantification of nitrite in a range of 0.2–800 μg/mL with a detection limit of 0.02 μg/mL. The method was applied to the determination of nitrite in 15 brands of fruit juice samples.     

A very sensitive flow-injection spectrophotometric determination method for iron (II) and total iron using 2′, 3, 4′, 5, 7-pentahydroxyflavone

In this study, an ultra-sensitive and highly selective, rapid flow-injection spectrophotometric method for the determination of iron (II) and total iron has been proposed. The method was based on the reaction between iron (II) and 2′, 3, 4′, 5, 7-pentahydroxyflavone in slightly acidic solution with a strong absorption at 415 nm. The carrier solution used was 1?×?10^?5 M 2′, 3, 4′, 5, 7-pentahydroxyflavone in 0.1 M HAc/Ac^? buffer solution at pH 4.5. Parameters that affect simultaneously the determination of iron (II) and interfering ions were tested. The relative standard deviation for the determination of 50 μg L^?1 iron (II) was 0.85 % (n?=?10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 3 μg L^?1, both based on injection volumes of 20 μL. The method has been successfully applied to the determination of iron (II) and total iron in water samples and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F.     

A nanosilver-based spectrophotometric method for determination of malachite green in surface water samples

A new spectrophotometric method is reported for the determination of nanomolar level of malachite green in surface water samples. The method is based on the catalytic effect of silver nanoparticles on the oxidation of malachite green by hexacyanoferrate (III) in acetate–acetic acid medium. The absorbance is measured at 610 nm with the fixed-time method. Under the optimum conditions, the linear range was 8.0?×?10^?9–2.0?×?10^?7?mol?L^?1 malachite green with a correlation coefficient of 0.996. The limit of detection (S/N?=?3) was 2.0?×?10^?9?mol?L^?1. Relative standard deviation for ten replicate determinations of 1.0?×?10^?8?mol?L^?1 malachite green was 1.86 %. The method is featured with good accuracy and reproducibility for malachite green determination in surface water samples without any pre-concentration and separation step.     

Validation of spectrophotometric method for Se(IV) determination: analytical applications

As selenium is an important part of the antioxidant enzymes and also because there are several studies suggesting a possible link between cancer and selenium deficiency, this paper presents a spectrophotometric method for the assay of Se(IV), using N,N-diethyl-p-phenylenediamine monohydrochloride as reagent. The proposed method is based on the reaction between the selenium and potassium iodide in low acidic medium, when iodine is released. This last product will further oxidise the new reagent. The final obtained product is strongly coloured in red and has an absorption maximum at 552 nm and molar extinction coefficient (ε) of 6.1?×?10⁴ L mol^?1 cm^?1. The optimum working conditions were established, and the developed method was validated, being characterised by a good linearity (in the range of 0.5–3.0 μg/mL), a limit of detection (0.0573 μg/mL) and a limit of quantification (0.1737 μg/mL). At the same time, the repeatability, the precision of the method and the accuracy were established. The proposed and validated method was applied with good results for the determination of Se(IV) in spring and bottled water from Iasi and also in pharmaceutical and cosmetic products.     

Utility of cefixime as a complexing reagent for the determination of Ni(II) in synthetic mixture and water samples

A simple, sensitive, and accurate UV spectrophotometric method has been developed for the determination of nickel in synthetic mixture and water samples. The method is based on the complexation reaction of nickel ion with cefixime, thus leading to the formation of Ni–cefixime complex in ethanol-distilled water medium at room temperature. The complex showed the maximum absorption wavelength at 332 nm. Beer’s law is obeyed in the working concentration range of 0.447–4.019 μg?mL^?1 with apparent molar absorptivity of 7.314?×?10³?L?mol^?1?cm^?1 and Sandell’s sensitivity of 0.008 μg/cm²/0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.016 and 0.054 μg?mL^?1, respectively. The factors such as cefixime concentration and solvent affecting the complexation reaction were carefully studied and optimized. The method is validated as per the International Conference on Harmonisation guideline. The method is successfully applied to the determination of Ni(II) in synthetic mixture and wadi water samples collected from Al Rustaq. The same water samples are also analyzed by atomic absorption spectrophotometry. Both methods determined the amount of Ni(II) in water sample and found to be approximately the same.     

Application of zirconium–iridium permanent modifier for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry

A novel and robust method for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry was developed, using zirconium–iridium coating as permanent modifier (140 μg Zr and 4 μg Ir). After 300 atomization cycles, it was necessary to add 2 μg of Ir. Due to the varying concentrations of Pb in atmospheric particulate matter, lead was monitored at two wavelengths, at the less sensitive line of 261.4 nm for high concentration samples (>20 μg?L^?1) or at 283.3 nm for the low concentration samples. Matrix-matched calibration had to be performed for quantitative recoveries (96–102 %). Following this approach, the four elements were determined in atmospheric particulate matter samples from an industrial area near the city of Athens in two different time periods (cold–warm) with limits of detection of 5.5 ng?m^?3 for Pb at 261.4 nm and 0.29 ng?m^?3 at 283.3 nm, 0.019 ng?m^?3 for Cd, 0.14 ng?m^?3 for As, and 0.22 ng?m^?3 for Ni. Lead, Cd, and As levels were very low, whereas Ni content was at comparable levels with other areas worldwide.     

Environmental assessment of 2-mercaptobenzimidazole based on the surface plasmon resonance band of gold nanoparticles

A colorimetric assay method is described for the environmental detection of 2-mercaptobenzimidazole (MBI) using surface plasmon resonance of gold nanoparticles (AuNPs). Stable and dispersed AuNPs with intensified plasmon resonance were prepared in situ using a simple, rapid, and eco-friendly procedure by applying ascorbic acid as a reducer and cetyltrimethylammonium bromide as a stabilizer. The presence of MBI has a strong effect on the plasmon absorbance of AuNPs, which was employed for the detection of MBI. The calibration curve was linear in the range of 1.0?×?10^?6–5.5?×?10^?5 mol/L of MBI; the detection limit was 8.4?×?10^?7 mol/L. The relative standard deviations for eight replicate measurements of 3.0?×?10^?6 and 5?×?10^?5 mol/L MBI were 3.9 and 1.4 %, respectively. The method was successfully applied to the determination of MBI in tap, river, sea, and heat exchanger cooling water samples.     

Ionic liquid-based dispersive liquid–liquid microextraction for the determination of formaldehyde in wastewaters and detergents

Spectrophotometry in combination with ionic liquid-based dispersive liquid–liquid microextraction (DLLME) was applied for the extraction and determination of formaldehyde in real samples. The method is based on the reaction of formaldehyde with methyl acetoacetate in the presence of ammonia. The variation in the absorbance of the reaction product was measured at 375?nm. An appropriate mixture of ethanol (disperser solvent) and ionic liquid, 1-hexyl-3-methylimidazoliumhexafluoro-phosphate [C₆MIM][PF₆] (extraction solvent) was rapidly injected into a water sample containing formaldehyde. After extraction, sedimented phase was analyzed by spectrophotometry. Under the optimum conditions, the calibration graph was linear in the range of 0.1–20?ng?mL^?1 with the detection limit of 0.02?ng?mL^?1 and limit of quantification of 0.08?ng?mL^?1 for formaldehyde. The relative standard deviation (RSD%, n?=?5) for the extraction and determination of 0.8?ng?mL^?1 of formaldehyde in the aqueous samples was 2.5%. The results showed that DLLME is a very simple, rapid, sensitive, and efficient analytical method for the determination of trace amounts of formaldehyde in wastewaters and detergents, and suitable results were obtained.     

The use of silica gel modified with allyl 6-methyl-4-phenyl-2-thioxo-1,2,3,4-tetrahydropyrimidine-5-carboxylate for selective separation and preconcentration of lead in environmental samples

The aim of the present work is the assessment of a new sorbent, prepared using silica gel coated with a pyrimidine derivative (allyl 6-methyl-4-phenyl-2-thioxo-1,2,3,4-tetrahydropyrimidine-5-carboxylate), for extraction and preconcentration trace amount of lead from different samples prior to determination by flame atomic absorption spectrometry. Common coexisting ions did not interfere with the separation and determination of lead at pH?6, so that lead ion completely adsorbed on the column. The limit of detection based on three times the standard deviation of the blank was found to be 0.53 ng?mL^?1 in original solution. Obtained sorption capacity for 1 g sorbent was 5.0 mg Pb. The linearity was maintained in the concentration range of 0.1–30.0 ng?mL^?1 for the concentrated solution. Eight replicate determinations of 2.0 μg?mL^?1 of lead in the final solution gave relative standard deviation of ±2.6 %. The proposed method was successfully applied to the determination trace amounts of lead in the environmental samples such as carrot, rice, zardchoobe, and real water samples.     

Flow injection spectrophotometric determination of methamidophos using online hydrolysis

A new protocol for the online spectrophotometric determination of methamidophos has been developed. The method is based on online hydrolysis of methamidophos, and the resulting hydrolyzed product is reacted with sodium nitroproside to form a colored complex. The calibration curve is linear over the concentration range of 0.5–20 μgml^?–?1, with a molar absorptivity of 2.5×10⁴ L mol^?1 cm^?1. The method is fast and reproducible with a sample throughput of 90 samples/h. The method is successfully applied to formulations and real samples.