巯基棉富集-毛细柱气相色谱法测定环境水中的甲基汞

用巯基棉富集-毛细柱气相色谱法对水中甲基汞进行测定,具有选择性强,回收率高,灵敏度高等优点。实际样品加标回收率达到85%以上,最低可检出0.6ng/L的浓度。研究结果表明,与填充柱法相比,毛细柱法对目标物的分离效果好,且不会发生柱中毒反应,避免了用氯化汞对色谱柱进行处理的步骤。论证了用甲苯代替苯做为萃取剂的可行性,证明用甲苯代替苯对测试结果没有显著影响,使用甲苯可以避免实验人员暴露于毒性较大的苯中的风险。     

地表水超痕量苯并(a)芘的检测及空白干扰消除

采用液液萃取-超高效液相色谱仪接荧光检测器测定地表水中超痕量的苯并(a)芘,并对方法空白的干扰因素进行探讨。研究发现,该法的空白干扰主要来自于溶剂二氯甲烷,溶剂经蒸馏提纯后可消除干扰。以重新蒸馏提纯的二氯甲烷为提取剂,方法的检测限为0.05 ng/L,加标回收率为87.4%~132%,且空白测定值低于方法检出限,可满足地表水中超痕量苯并(a)芘检测的需求。     

小体积液液萃取气相色谱法测定地表水中硝基苯类

建立了一种小体积液液萃取气相色谱法快速测定地表水中硝基苯类化合物的分析方法。方法具有适用性广、溶剂用量少和操作简便等特点。当萃取剂甲苯用量为1.5 ml时,萃取富集效率可达191~332倍,回收率为90.7%~102%,相对标准偏差为2.9%~5.1%,检出限为0.000 3~0.005 mg/L。     

固相微萃取一气相色谱火焰离子化测定挥发性有机物BTEX

固相微萃取方法是一种有效的无溶剂样品前处理方法,对这种方法用于苯,甲苯,乙苯,二甲苯(BTEX)等挥发性有机污染物的样品采集,通过毛细管气相色谱火焰离子化检测器测定,对萃取纤维涂层厚度的影响进行了研究,对萃取时间和解吸时间等影响因素进行了讨论.     

水中有机磷农药分析前处理方法探讨

分别采用液-液萃取、固相萃取前处理方法,提取水中10种常见的有机磷农药,对比了这两种提取方法的测定结果、经济成本、花费时间及对环境的影响,建议逐步用固相萃取法取代液？液萃取法提取水中有机磷农药。     

分散液液微萃取-气相色谱法测定地表水中松节油

采用分散液液微萃取-气相色谱法测定地表水中松节油,通过试验优化萃取剂、分散剂的种类和用量、盐度等影响萃取效率的条件,使该方法在10.0μg/L~500μg/L范围内线性良好,方法检出限为1.6μg/L。用该方法测定实际水样,结果未检出。实际水样的3个质量浓度水平加标回收率为83.6%~104%,RSD为2.1%~8.3%。     

超声辅助离子液体-分散液液微萃取-高效液相色谱法测定水中苯胺类化合物

本研究建立了超声辅助离子液体-分散液液微萃取-高效液相色谱测定环境水样中苯胺(AN)、对氟苯胺(4-FA)、对硝基苯胺(4-NA)、对氯苯胺(4-CA)四种苯胺化合物的方法。以最常用的烷基咪唑六氟磷酸盐类离子液体为萃取剂,通过超声加速萃取剂的分散程度,提高了萃取效率。该方法的检测限达到0.1~73 ng/ml,对黄河水和自来水中的加标回收率均在90.5%~113%之间,回收效果良好。与传统的液液萃取相比,该萃取方法具有绿色、快速、富集效果好、有机溶剂消耗小的优点,可以满足环境水体中苯胺类化合物的测定。     

液液萃取-气质联用法测定水中20种农药类有机物

采用液液萃取-气质联用法同时测定水中20种农药类有机物。对前处理过程中萃取剂的选择、用量，萃取时间，盐析剂用量，有机改进剂的加入等条件进行了优化，使得各组分在0．500μg/L～50．0μg/L范围内线性良好。方法检出限为0．02μg/L～0．19μg/L；平行测定7次混合标准溶液，RSD为0．3％～9．1％；对20种农药类有机物混合标准溶液进行加标回收试验，回收率为90．5％～110％。该方法优化了《生活饮用水标准检验方法》（ GB 5750-2006）中农药类有机污染物的检测方法，满足常规测定的要求。     

硝基苯等四神化合物 气相色谱法

硝基苯等四神化合物　气相色谱法概述１．方法原理：水中硝基苯等四种化合物经甲苯一次革取，将革取液注人色谱仪，通过毛细柱将混合物分离成单个化合物，用电子捕获检测器进行测定，采用外标峰高法定量。２．干扰及消除：水中存在苯、二甲苯、氯化苯、二氯苯、氯仿、四氯...     

4-APP萃取蒸馏法测定地表水中挥发酚的改进

改进了4-APP萃取蒸馏法测定水中酚的方法,以100 mL馏出液代替250 mL馏出液,改变了原方法实验过程时间长、费时费力的缺点,特别适合地表水大批量样品的分析。经两种方法测定结果比对,吸光值变化不大,标准曲线相似,回收率符合规范要求;经t检验,测定结果无显著性差异。测定时间由原来的45 min缩短至25 min左右,大大提高了工作效率。     

吹扫捕集气相色谱法测定水中苯系物

对吹扫捕集气相色谱法分析水中苯系物(苯、甲苯、乙苯、对、间-二甲苯、邻-二甲苯、异丙苯)的方法进行了研究,并讨论了吹扫捕集测定的优化条件,探讨了影响测定的各因素应注意的问题,并对实际水样进行了方法对比实验.结果表明,该方法操作简单、灵敏度高、重复性好,适用于饮用水、地表水、污水的测定.     

顶空-气相色谱/质谱联用法测定水和废水中8种苯系物

采用顶空进样-气相色谱/质谱联用法(HS-GC/MS)测定水和废水中苯、甲苯、乙苯、对二甲苯、间二甲苯、邻二甲苯、异丙苯、苯乙烯等8种苯系物,优化了分析条件,讨论了色谱柱极性、加热温度、平衡时间和进样次数对测定结果的影响。8种苯系物在1.00μg/L～1 000μg/L范围内线性良好,方法检出限为0.22μg/L～0.38μg/L,实际样品平行测定的相对标准偏差5.0%,加标回收率在86.0%～115%之间。     

差分光谱法连续监测空气中SO2、NO2、苯、甲苯方法探讨

差分光谱法(简称DOAS)已广泛用于空气中SO2、NO2、苯、甲苯监测.通过对差分光谱法监测结果与其他传统仪器进行时比,发现用DOAS监测SO2、NO2与点式仪器有较好的一致性,但用DOAS系统监测苯、甲苯与气相色谱法有机物连续监测结果差异较大,相关性较差,运行有一定的局限性.另外,本文对DOAS的最佳运行条件进行了探讨,发现影响光强的氙灯老化和气候条件对DOAS系统运行有较大影响.     

Determination of volatile organic compounds pollution sources in malaysian drinking water using multivariate analysis

A field investigation was conducted at all water treatment plants throughout 11 states and Federal Territory in Peninsular Malaysia. The sampling points in this study include treatment plant operation, service reservoir outlet and auxiliary outlet point at the water pipelines. Analysis was performed by solid phase micro-extraction technique with a 100 μm polydimethylsiloxane fibre using gas chromatography with mass spectrometry detection to analyse 54 volatile organic compounds (VOCs) of different chemical families in drinking water. The concentration of VOCs ranged from undetectable to 230.2 μg/l. Among all of the VOCs species, chloroform has the highest concentration and was detected in all drinking water samples. Average concentrations of total trihalomethanes (THMs) were almost similar among all states which were in the range of 28.4--33.0 μg/l. Apart from THMs, other abundant compounds detected were cis and trans-1,2-dichloroethylene, trichloroethylene, 1,2-dibromoethane, benzene, toluene, ethylbenzene, chlorobenzene, 1,4-dichlorobenzene and 1,2-dichloro - benzene. Principal component analysis (PCA) with the aid of varimax rotation, and parallel factor analysis (PARAFAC) method were used to statistically verify the correlation between VOCs and the source of pollution. The multivariate analysis pointed out that the maintenance of auxiliary pipelines in the distribution systems is vital as it can become significant point source pollution to Malaysian drinking water.     

Assessment of dermal exposure to benzene and toluene in shoe manufacturing by activated carbon cloth patches

OBJECTIVES: The aim of this investigation was to use activated carbon cloth (ACC) patches to study the probability and extent of dermal exposure to benzene and toluene in a shoe factory. METHODS: Inhalation and dermal exposure loading were measured simultaneously in 70 subjects on multiple days resulting in 113 observations. Dermal exposure loading was assessed by ACC patches attached to likely exposed skin areas (e.g. the palm of the hand and abdomen). A control patch at the chest and an organic vapor monitor (OVM) were used to adjust the hand and abdomen patches for the contribution from the air through passive absorption of benzene and toluene on the ACC patches. Systemic exposure was assessed by quantification of unmetabolized benzene (UBz) and toluene (UTol) in urine. RESULTS: Mean air concentrations for the study population were 1.5 and 7.5 ppm for benzene and toluene, respectively. Iterative regression analyses between the control patch, OVM and the dermal patches showed that only a small proportion of the ACC patches at the hand had likely benzene (n = 4; mean 133 microg cm(-2) h(-1)) or toluene (n = 5; mean 256 microg cm(-2) h(-1)) contamination. Positive patches were exclusively observed among subjects performing the task of gluing. Significant dermal exposure loading to the abdomen was detected only for toluene (n = 2; mean 235 microg cm(-2) h(-1)). No relation was found between having a positive hand or abdomen ACC patch and UBz or UTol levels. In contrast a strong association was found between air levels of benzene (p = 0.0016) and toluene (p < 0.0001) and their respective urinary levels. CONCLUSIONS: ACC patches are shown to be a useful technique for quantifying the probability of dermal exposure to organic solvents and to provide estimates of the potential contribution of the dermal pathway to systemic exposure. Using ACC patches we show that dermal exposure to benzene and toluene in a shoe manufacturing factory is probably rare, and when it occurred exposures were relatively low and did not significantly contribute to systemic exposure.     

杭州湾上虞工业园区环境空气中苯系物的调查及其特征

用活性炭吸附空气中有机物苯、甲苯、乙苯、对二甲苯、间二甲苯、邻二甲苯、苯乙烯,二硫化碳解吸后用毛细管气相色谱法同时测定,各组分线性响应良好,曲线相关系数均大于0.995;灵敏度高,检出限在0.01～0.03μg/ml之间;回收率在82.4%～105.8%之间。苯、甲苯、二甲苯均未超过GB 16297—1996中规定的0.5、0.3、1.5mg/m3,也未超过新污染源大气污染物排放限值中规定的0.4、2.4、1.2mg/m3,苯乙烯浓度也远小于恶臭污染物排放标准GB 14554—93中规定的一级标准3.0mg/m3,虽然工业园区及其周边大气环境均能检测出苯系物,但都在国家相关标准范围内。     

Diffusive Sampling of VOCs as an Aid to Monitoring Urban Air Quality

Diffusive sampling of Volatile Organic Compounds (VOCs) onto thermal desorption tubes, followed by gas chromatography, is an established technique for area or personal monitoring of typical workplace concentrations and there has been increasing interest in extending the application to environmental levels, particularly for benzene, toluene and xylene (BTX). Diffusive sampling rates for BTX on Chromosorb 106 and Carbograph-1 (a graphitised carbon) were measured over periods of 1-4 weeks in field validation experiments using ambient air and parallel pumped sampling (the reference method) at the HSL site in central Sheffield. The reference method was also used to investigate the possible bias of an open-path spectrophotometer (OPSIS) used by Sheffield City Council. A bias for BTX was suspected from results of a two-week initial exercise in which several diffusive samplers were placed close to the light path. In the full field validation of the diffusive samplers carried out subsequently, the significant bias of BTX concentrations reported by OPSIS were confirmed when compared with concurrent results from the reference method. OPSIS gave benzene and toluene values up to eight times higher than expected from the GC measurements. Xylene discrepancies were smaller, but in one 3-day peak episode, OPSIS demonstrated a negative correlation with GC.     

Environmental Monitoring of Benzene and Alkylated Benzene from Vehicular Emissions

The volatile organic pollutants from direct vehicular exhaust were trapped with activated charcoal, desorbed with carbon disulphide and analysed by GC/MS with tert-butyl benzene as an internal standard. A comparative study was made from the exhaust of 1000 cc, 1300 cc, 1600 cc cars, pickup, lorry(diesel), 125 cc and 70 cc motorbikes. The level of pollutants emitted were in the following order, motorbike(petrol) car(petrol) pickup(petrol) lorry(diesel). The range of highest emission (125 cc motorbike) to the lowest emission (lorry(diesel)) was of the order of 102 for benzene, 6×102 for ethyl benzene, 5×102 for toluene and 3×102 for xylenes. Among cars, those fitted with catalytic convertors emitted a lower level of benzene (2 to 3 times) when compared with those without catalytic convertors. Similar studies on the air in air-conditioned buses, non air-conditioned buses and three metres from the edge of the road shows that they have the same pollutant level. The level of these pollutant as compared to those from direct car exhaust are of the order of 102 times less for benzene, xylene and toluene and 103 times less for ethylbenzene. The levels of benzene, toluene, ethylbenzene and xylenes by the road side and in the buses were found to be lower than the exposure limits of ACGIH, OSHA and EH40.     

BTX measurements with diffusive samplers in the vicinity of a cokery: comparison between ORSA-type samplers and pumped sampling

In the framework of new European directives in the field of ambient air quality assessment specific requirements for measurement methods for benzene will be defined and have to be met in the future. In a residential area in the vicinity of a cokery a comprehensive monitoring programme for BTX compounds (benzene, toluene, xylenes) was carried out with diffusive samplers. Measurement results from 20 sites show a distinct spatial distribution of benzene concentrations which is caused by the emissions of the plant. Comparisons with two pumped measurement methods reveal excellent agreement in the case of benzene. An assessment of measurement uncertainty for the diffusive method is presented in terms of standard deviations from parallel measurements (precision) and by comparison with a reference method according to national and international standards. Data quality objectives required by an upcoming European directive for benzene can be met by diffusive sampling.