太原市大气颗粒物中重金属的污染特征及来源解析

为了解太原市采暖期大气颗粒物不同粒径中重金属的污染特征及其来源,于2012年10月—2013年2月对环境空气中颗粒物采样,用原子吸收分光光度法测定样品中Fe、Pb、Cu、Ni、Cr、Cd、Mn、Zn等8种元素的含量。结果表明,太原市采暖期重金属浓度从高到低依次为FePbMnZnCrCuNiCd。重金属Pb、Mn、Zn、Ni、Cd主要富集在PM2.5中;Cr主要富集在PM10中;Cu主要富集在PM5中;Fe主要在粒径大于2.5μm的粗粒子中富集。除Zn外,其他7种元素浓度均表现为灰霾期采暖期采暖前。通过主因子分析表明,太原市大气颗粒物中重金属主要来源于冶金、有机合成工业、燃煤、汽车尾气、土壤尘等。     

乌鲁木齐采暖期TSP、PM10、PM5、PM2.5中重金属污染水平评价

采用石墨炉原子吸收分光光度法、双道原子荧光光谱法研究乌鲁木齐市采暖期前期与后期不同粒径大气颗粒物(TSP、PM_(10)、PM_5、PM_(2.5))中Hg、As、Zn、Pb、Ni等5种重金属元素的质量浓度,并对重金属污染水平进行评价。Hg质量浓度为0.3~5.7 ng/m3;As质量浓度为15.3~122.5 ng/m~3;Zn质量浓度为298.0~1 686.5 ng/m~3;Pb质量浓度为0.5~88.8 ng/m~3;Ni质量浓度为10.4~25.5 ng/m~3。Igeo计算得出采暖期后期的TSP、PM_(10)、PM_5、PM_(2.5)中各重金属Igeo值均高于采暖期前期,其中Hg元素为严重污染;富集因子分析得出Hg、Zn元素的EFi值大于10,说明这些元素是人为源贡献。通过研究乌鲁木齐市不同时期、不同粒径大气颗粒物中各种重金属污染状况,为乌鲁木齐大气污染治理提供科学支持。     

Heavy metals in urban ambient PM10 and soil background in eight cities around China

The ambient PM₁₀ and background soil samples were collected and analyzed with ICP-AES in eight cities around China to investigate the levels of ten heavy metals (Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, and Pb). The mean concentrations of ten heavy metals in PM₁₀ of the eight cities of China followed the order of Zn?>?Pb?>?Mn?>?Cu?>?Ni?>?Cr?>?Co?>?V. The metals in the ambient PM₁₀ and soil were compared in each city to evaluate the heavy metal mass fraction from anthropogenic sources in ambient air. The CD values in these cities were all above 0.2, indicating that the ingredients spectrums of PM₁₀ and soil vary markedly. Most heavy metals were enriched in PM₁₀, except Fe and Ti. The results showed that almost all the cities suffer important heavy metal pollution from anthropogenic sources. The eight cities were also grouped according to their similarity in heavy metals of ambient PM₁₀ by cluster analysis to investigate the relationship between the heavy metals and the pollution sources of each city. The conclusion was that the eight cities were divided into three clusters which had similar industrial type and economy scale: the first cluster consisted of Shenzhen, Wuxi, and Guiyang; followed by Jinan and Zhengzhou as the second grouping; and the third group had Taiyuan, Urumqi, and Luoyang.     

PM2.5中重金属形态分布及其在模拟酸雨中的释放

对西安市夏季PM_2.5中6种重金属元素的化学形态进行分析,并研究了模拟酸雨淋溶条件下PM_2.5中6种元素的释放过程。结果表明,近80%的Cr和Fe分布在有机质、氧化物、硫化物结合态和残渣态中,Cd在大气环境中的化学性质很活泼,具有很强的毒害性,Pb、As、和Hg 3种元素主要以碳酸盐态、可氧化态与可还原态存在于环境中;PM_2.5中6种元素均有不同程度的释放,Cd释放率高于其他元素,Fe释放率最低,pH降低有利于颗粒物中重金属元素的释放。     

上海市浦东新区大气细颗粒物中重金属污染特征及来源解析

于2017年对浦东城区和郊区大气PM2.5中的重金属特征和来源进行了分析。结果表明,K、Fe、Na、Ca、Mg、Al等矿物元素为浦东新区PM2.5中含量最高的金属元素,其中K的年均值为297.3 ng/m^3。浦东城区的不同元素在季节变化上呈现较为不同的变化规律,郊区的金属元素值大部分呈现春季先逐月下降,在夏、秋季有起伏波动,在10月之后逐渐上升;沙尘+道路源+建筑扬尘、煤燃烧、工业排放、金属冶炼、船舶排放、海盐+垃圾焚烧+生物质燃烧为浦东城区PM2.5中重金属元素的6大类主要来源。其中沙尘+道路源+建筑扬尘对Ca的贡献率为82.7%,煤燃烧对As的贡献率为86.6%,工业排放对SO4^2-的贡献率达到65.9%,金属冶炼对Cr的贡献率为75.7%,船舶排放对V的贡献率为97.5%、海盐+垃圾焚烧+生物质燃烧对Cl^-的贡献率为93.0%。煤燃烧和金属冶炼主要来自于西部方向。船舶排放分布在长江口及其延伸带。浦东新区PM2.5中重金属元素的质量浓度与本地源排放强度、外界传输和大气扩散条件均有密切关系。     

Seasonal variation of Sarpa salpa fish toxicity, as related to phytoplankton consumption, accumulation of heavy metals, lipids peroxidation level in fish tissues and toxicity upon mice

The aim of this work was to investigate for Sarpa salpa the seasonal trend in the food sources, heavy metals bioaccumulation and the oxidative stress in the organs. In addition, the toxicity was assessed by mouse bioassay of extract of the fish's organs collected in autumn, the peak of occurrence of hallucinatory syndrome. The toxicity was further studied for compounds present in epiphyte collected from the sea at the end of spring and in summer that are digested by the S. salpa in these seasons. We observed a higher lipid peroxydation in different tissues of S. salpa compared to the control fish Diplodus annularis. Furthermore, heavy metals accumulation in organs of these fish showed a significant variation between the two species (P?<?0.05). The lethal dose (LD50%) determined for crude ciguatoxin (neurotoxins) extracts of viscera, liver, brain and muscle of S. salpa were as follows: 1.217, 2.195, 14.395, 18.645 g/kg mouse, respectively. We noticed a significant correlation (P?<?0.05) between the total amount of toxic dinoflagellates and the level of TBARS in the liver, the brain and the muscle, this for all seasons and all sizes. Moreover, the cytotoxic effect observed for epiphytes extract confirms the transfer of toxins originating from toxic dinoflagellates, which live as epiphytes on P. oceanica leaves, to the fish by grazing. Our work indicates that, toxic phytoplanktons and heavy metals accumulation are responsible for the increase of oxidative stress in the organs of S. salpa. Hence, the edible part of S. salpa, especially the viscera and liver, can cause a threat to human health, and consumption should, for this reason, be dissuaded.     

Heavy metal pollution across sites affecting the intestinal helminth communities of the Egyptian lizard, Chalcides ocellatus (Forskal, 1775)

This study aimed to investigate the possible effects of heavy metal pollution across sites and some biological factors on helminth communities infecting the lizard, Chalcides ocellatus. The possibility of heavy metal accumulation by such helminths was also investigated. A total of 202 C. ocellatus were collected from three different sites (industrial, rural, and urban systems) in Ismailia governorate, Egypt, during summer 2009. The lizards were classified according to their sex and size and were examined for the intestinal helminths. Heavy metal levels were detected in the intestinal tissue of the lizards and the recovered helminths. Species richness was 6, 5, and 3 in rural, urban, and industrial systems, respectively. Significant site variations regarding infection prevalence, intensity, and abundance were encountered at different levels. Some noticeable effects of the host size were found. The significant differences found between the metal levels of the intestinal tissues and the recovered helminths and the other relations found in this study may be indications for a possible metals accumulation capacity by helminths. The cestode Oochoristica tuberculata could be a promising biomonitor for Cu and Pb, while the intestinal nematodes were less sensitive to the pollution. Differences in the accumulation capacity may be attributed to the intensity of infection, parasite species, and metal. The observed patterns of distribution and occurrence of helminths and the metals accumulation capacity reflect the need for more studies since this study proposes the model intestinal helminth/C. ocellatus as another promising bioindication system in the terrestrial habitat, especially in areas where the lizard C. ocellatus are available.     

Analysis of acidic components, heavy metals and PAHS of particulate in the Changwon–Masan area of Korea

This study is an analysis of the concentrations and components of heavy metals in PM_2.5 and the total suspended particulate (TSP) collected at a mechanical industrial complex (IC) site in Changwon and at a residential site in Masan, Korea. Particulate was collected during two sampling periods, from the late summer to the early fall and from the middle to late fall, at the IC site and one sampling period, from the middle fall to the early winter, at the residential site. PM_2.5 and TSP samples were taken by an annular denuder system and a hi-volume air sampler, respectively. The authors also identified the concentrations and components of heavy metals extracted from the PM_2.5 and TSP filters, the acidic components extracted from the PM_2.5 filters, and the polycyclic aromatic hydrocarbons (PAHs) extracted from polyurethane foam (PUF) plug. The average concentrations of the PM_2.5 collected at the IC and residential sites were very similar. Major sources of PM_2.5 at the study sites, however, were air emissions from vehicles and industry as well as emissions from residential heating and soil origins, respectively. The higher concentrations of the TSP at the IC site, as compared to those at the residential site, were due to either increased suspended dust from vehicle emissions or re-suspended road dust because of increased vehicle speeds near the IC site. Heavy metal concentrations in the TSPs were higher than those in the PM_2.5. The heavy metal concentrations in the PM_2.5 and TSP at the IC site with heavy traffic were substantially greater than those at the residential site. The concentrations of TSP and heavy metals and PAHs in PM during the period of the middle to late fall was much higher than those during the period of the late summer to early fall at the IC site. This is because of the difference in meteorological characteristics and energy uses between two periods. The residential site also showed higher concentrations of acidic anions while the IC site showed higher concentrations of acidic cation. Secondary aerosols or particulates, such as ammonium nitrate or ammonium nitrite, might have been important constituents of the PM_2.5 at the residential site. The PAHs in the TSP collected at the IC site was greatly affected by traffic and industry emissions consisting mostly of high molecular weight PAHs with two to four rings. PAHs in the TSP at the site, however, were affected by residential heating and air emissions from small chemical plants having higher concentrations of low molecular weight PAHs with five to six rings.     

Characterization and Identification of the Sources of Chromium, Zinc, Lead, Cadmium, Nickel, Manganese and Iron in Pm10 Particulates at the Two Sites of Kolkata, India

Monitoring of ambient PM₁₀ (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 μm aerodynamic diameter) has been done at residential (Kasba) and industrial (Cossipore) sites of an urban region of Kolkata during November 2003 to November 2004. These sites were selected depending on the dominant anthropogenic activities. Metal constituents of atmospheric PM₁₀ deposited on glass fibre filter paper were estimated using Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). Chromium (Cr), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), manganese (Mn) and iron (Fe) are the seven toxic trace metals quantified from the measured PM₁₀ concentrations. The 24 h average concentrations of Cr, Zn, Pb, Cd, Ni, Mn and Fe from ninety PM₁₀ particulate samples of Kolkata were found to be 6.9, 506.1, 79.1, 3.3, 7.4, 2.4 and 103.6 ng/m³, respectively. The 24 h average PM₁₀ concentration exceeded national ambient air quality standard (NAAQS) as specified by central pollution control board, India at both residential (Kasba) and industrial (Cossipore) areas with mean concentration of 140.1 and 196.6 μg/m³, respectively. A simultaneous meteorology study was performed to assess the influence of air masses by wind speed, wind direction, rainfall, relative humidity and temperature. The measured toxic trace metals generally showed inverse relationship with wind speed, relative humidity and temperature. Factor analysis, a receptor modeling technique has been used for identification of the possible sources contributing to the PM₁₀. Varimax rotated factor analysis identified four possible sources of measured trace metals comprising solid waste dumping, vehicular traffic with the influence of road dust, road dust and soil dust at residential site (Kasba), while vehicular traffic with the influence of soil dust, road dust, galvanizing and electroplating industry, and tanning industry at industrial site (Cossipore).     

Heavy metal pollution of ambient air in Nagpur City

Heavy metals released from different sources in urban environment get adsorbed on respirable particulate matter less than 10 μm in size (PM₁₀) and are important from public health point of view causing morbidity and mortality. Therefore, the ambient air quality monitoring was carried out to study the temporal and special pattern in the distribution of PM₁₀ and associated heavy metal content in the atmosphere of Nagpur, Maharashtra State, India during 2001 as well as in 2006. PM₁₀ fraction was observed to exceed the stipulated standards in both years. It was also observed that minimum range of PM₁₀ was observed to be increased in 2006 indicating increase in human activity during nighttime also. Six heavy metals were analyzed and were observed to occur in the order Zn > Fe > Pb > Ni > Cd > Cr in 2006, similar to the trend in other metro cities in India. Lead and Nickel were observed to be within the stipulated standards. Poor correlation coefficient (R ²) between lead and PM₁₀ indicated that automobile exhaust is not the source of metals to air pollution. Commercial and industrial activity as well as geological composition may be the potential sources of heavy metal pollution. Total load of heavy metals was found to be increased in 2006 with prominent increase in zinc, lead, and nickel in the environment. Public health impacts of heavy metals as well as certain preventive measures to mitigate the impact of heavy metals on public health are also summarized.     

Assessment of heavy metals in aquatic sediments

The concentration of heavy metals in the bottom sediment and interstitial water collected from two reservoirs in Singapore was found to be enriched. A distribution coefficient,K _d , was used to assess the chemical stability of heavy metals in the sediments. Numerical models were used to assess (1) the redistribution of heavy metals in a changing environment, and (2) long-term self clean-up capabilities of a reservoir.     

The occurrence of heavy metals in irrigated and non-irrigated arable soils,NW Albania

The study analysed the content of heavy metals in surface soil and sediment samples from the Bregu i Matit Plain in NW Albania in relation to irrigation in order to evaluate the soil pollution and the potential risk to human health. Evaluation of soil pollution was performed using the enrichment factor and geo-accumulation index. Contents of cadmium, chromium and nickel of irrigated soils were significantly higher than those of non-irrigated soil, while contents of lead (in three of the irrigated locations), zinc and arsenic (in one of the irrigated locations) were significantly lower. Correlation analysis (CA) and principal component analysis (PCA) indicated that the primary source of the first three metals was irrigation, and the last three metals were originated from other anthropic sources, like the use of chemicals, etc. Enrichment factor (E _f) calculation showed that irrigated soils were most enriched in cadmium, chromium, copper and nickel. Index of geo-accumulation (I _geo) revealed that arable soils of Bregu i Matit are unpolluted to moderately polluted with cadmium, chromium, copper and zinc and moderately to strongly polluted with nickel and arsenic. The presence of heavy metals in the studied soils indicates a potential risk of transfer of these elements in the food chain. Therefore, further studies on the speciation of heavy metals in the studied soils in order to evaluate their mobility are needed.     

Assessment of trace metals using lichen transplant from automobile mechanic workshop in Ile-Ife metropolis,Nigeria

The level of air pollution around the automobile mechanic workshops has been generally overlooked. This study, examined the level of trace metals in automobile mechanic workshops and the suitability of using transplanted lichen thalli of Lepraria incana for measuring air pollution in such areas. Samples of the lichen thalli were transplanted into seven different sites and were attached to the bark of trees at each site. The samples were harvested from the sites after 3-month exposure. Concentrations of Pb, Cu, Cd, Fe, Zn, and S content were determined using an atomic absorption spectrophotometer. Results showed that there was a significant difference in the trace metals concentrations across the sites (p?<?0.05). The analyzed lichen samples showed a range of 91.26–119.35 ppm for Fe, 30.23–61.32 ppm for Zn, 1.25–2.45 ppm for Cu, 0.017–0.043 ppm for Cd, 0.018–0.051 ppm, and 0.37–0.42 ppm for S. From the study, sites 6 and 7 presented higher concentrations of Cd, Pb, and Zn than other sites. The enrichment factor calculated showed that Zn, Cd, and Pb were greatly enriched from the workshops. The trend in the concentration of these heavy metals suggests that activities in these workshops might become a major source of certain heavy metals in the environment and if the pollution activities persist, it might become worrisome over time.     

Pollution and Genetic Structure of North American Populations of the Common Dandelion (Taraxacum Officinale)

Assessing the genetic structure of natural populations differentially impacted by anthropogenic contaminants can be a useful tool for evaluating the population genetic consequences of exposure to pollution. In this study, measures of genetic diversity at variable-number-tandem-repeat loci in six dandelion populations (3 urban and 3 rural) showed patterns that may have been influenced by exposure to environmental contaminants. Mean genetic similarity among individuals within a population was significantly and positively correlated with increasing levels of airborne particulate matter ( 10 m, PM₁₀) and soil concentrations of four metals (Cd, Fe, Ni and Pb). In addition, mean genetic similarity was always significantly higher at the urban sites compared to rural sites. There was a significant negative correlation between the number of genotypes at a site and increasing amounts of PM₁₀, concentrations of five soil metals (Cd, Cu, Fe, Ni and Pb), leaf tissue levels of Fe and a significant positive correlation between the extent of clonality at a site and levels of PM₁₀ and soil concentrations of five metals (Cd, Cu, Fe, Ni and Pb). Although, this study does not directly establish a causal link between the specific contaminants detected at the study sites and differences in genetic diversity, our data are consistent with the hypothesis that pollution-induced selection has contributed in some fashion to the lower genetic diversity found at the urban sites.     

A Comparison Between Two Moss Species Used as Transplants for Airborne Trace Element Biomonitoring in NE Italy

Transplants of the mosses Hypnum cupressiforme and Pseudoscleropodium purum used as active biomonitors of airborne trace elements were compared in a survey carried out at Trieste (NE Italy). Twelve elements were considered: Al, As, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Ti, V, Zn. Water-washed materials of H. cupressiforme and P. purum, collected in a remote area to prepare transplants, showed comparable content of all elements, excluding Pb. Transplants of P. purum showed a significantly higher accumulation of Al, Fe, Pb and Ti; higher levels of Cu and V were accumulated in H. cupressiforme. Losses of some elements occurred in some samples of both species; the most consistent losses regarded Cr and Mn. Accumulation data of Al, As, Cd, Hg, Zn found in the two transplanted sets were not correlated. Differences in element uptake in the two mosses are likely to depend mainly on morphology, and probably on the different forms of emission and deposition types of the elements. The two mosses showed an overall accordance in discriminating sites highly and scarcely affected by trace element depositions, although they accumulated some elements, in particular Hg and Zn, in different ways. P. purum proved to be a better accumulator than H. cupressiforme, showing similar or higher accumulation and lower loss of almost all elements, especially those related to particulate, dry depositions; H. cupressiforme could be effective in detecting large-scale patterns, related to wet depositions. These results indicate that these mosses cannot be used interchangeably for monitoring particular elements, and are able to provide complementary information on different, local and long-range deposition patterns.     

Distribution and chemical partitioning of heavy metals in marine near-shore sediment cores: a case study from the Xugou, Lianyungang, China

The concentrations and chemical partitioning of heavy metals (Co, Cr, Ni, Zn, Cu, and Pb) in the marine near-shore sediment cores were investigated. Typically, the mean concentrations from Core B sediment samples were 98.6, 21.1, 47.0, 46.4, 107.6, and 31.9 mg kg^???1 for Cr, Co, Ni, Cu, Zn, and Pb, respectively. The heavy metal concentrations were normalized to commonly used reference elements Al, Li, Sc, and total organic carbon. Based on Pearson coefficients, Li was found to be a good normalizer for Co (r?= 0.974), Cr (r?= 0.967), Ni (r?= 0.898), and Zn (r?= 0.929) in 80 sediment samples from three sampling sites. However, the correlation coefficients between Li and Cu, and Li and Pb were relatively low. Multivariate statistic approaches (Principal Component Analysis and Cluster Analysis) were adopted for data treatment, allowing the identification of two main factors controlling the heavy metal variability in the sediments. Heavy metals in the enrichment sections were evaluated by a sequential extraction method for possible chemical forms in sediments. The results showed that the residual, Fe/Mn oxides and Organic/sulfide fractions were dominant geochemical phases in the enriched sections, indicating low bioavailability of heavy metals in sediments.     

Demonstrating PM<Subscript>2.5</Subscript> and road-side dust pollution by heavy metals along Thika superhighway in Kenya,sub-Saharan Africa

This study assessed the level of heavy metal in roadside dust and PM_2.5 mass concentrations along Thika superhighway in Kenya. Thika superhighway is one of the busiest roads in Kenya, linking Thika town with Nairobi. Triplicate road dust samples collected from 12 locations were analysed for lead (Pb), chromium (Cr), cadmium (Cd), nickel (Ni), zinc (Zn), and copper (Cu) using atomic absorption spectrophotometry (AAS). PM_2.5 samples were collected on pre-weighed Teflon filters using a BGI personal sampler and the filters were then reweighed. The ranges of metal concentrations were 39–101 μg/g for Cu, 95–262 μg/g for Zn, 9–28 μg/g for Cd, 14–24 μg/g for Ni, 13–30 μg/g for Cr, and 20–80 μg/g for Pb. The concentrations of heavy metals were generally highly correlated, indicating a common anthropogenic source of the pollutants. The results showed that the majority of the measured heavy metals were above the background concentration, and in particular, Cd, Pb, and Zn levels indicated moderate to high contamination. Though not directly comparable due to different sampling timeframes (8 h in this study and 24 h for guideline values), PM_2.5 for all sites exceeds the daily WHO PM_2.5 guidelines of 25 μg/m³. This poses a health risk to people using and working close to Thika superhighway, for example, local residents, traffic police, street vendors, and people operating small businesses. PM_2.5 levels were higher for sites closer to Nairobi which could be attributed to increased vehicular traffic towards Nairobi from Thika. This study provides some evidence of the air pollution problem arising from vehicular traffic in developing parts of the world and gives an indication of the potential health impacts. It also highlights the need for source apportionment studies to determine contributions of anthropogenic emissions to air pollution, as well as long-term sampling studies that can be used to fully understand spatiotemporal patterns in air pollution within developing regions.     

External Contribution to Urban Air Pollution

Elevated particulate matter concentrations in urbanlocations have normally been associated with local trafficemissions. Recently it has been suggested that suchepisodes are influenced to a high degree by PM₁₀sources external to urban areas. To further corroboratethis hypothesis, linear regression was sought betweenPM₁₀ concentrations measured at eight urban sites inthe U.K., with particulate sulphate concentration measuredat two rural sites, for the years 1993–1997. Analysis ofthe slopes, intercepts and correlation coefficientsindicate a possible relationship between urban PM₁₀and rural sulphate concentrations. The influences of winddirection and of the distance of the urban from the ruralsites on the values of the three statistical parametersare also explored. The value of linear regression as ananalysis tool in such cases is discussed and it is shownthat an analysis of the sign of the rate of change of theurban PM₁₀ and rural sulphate concentrations providesa more realistic method of correlation. The resultsindicate a major influence on urban PM₁₀ concentrations from the eastern side of the UnitedKingdom. Linear correlation was also sought using PM₁₀ data from nine urban sites in London and nearby ruralRochester. Analysis of the magnitude of the gradients andintercepts together with episode correlation analysisbetween the two sites showed the effect of transportedPM₁₀ on the local London concentrations. This articlealso presents methods to estimate the influence of ruraland urban PM₁₀ sources on urban PM₁₀ concentrations and to obtain a rough estimate of thetransboundary contribution to urban air pollution from thePM₁₀ concentration data of the urban site.     

Ionic and heavy metal composition of respirable particulate in Madurai, India

Airborne particulate matter (PM₁₀) was collected for a period of 1 year at six locations in Madurai city, India. The chemical analyses on PM₁₀ samples were carried out for the estimation of heavy metals and ions using atomic absorption spectroscopy and ion chromatography respectively. The average PM₁₀ concentrations varied from 97.2 to 152.5 μg/m³, which were found to be below the Indian air quality standards. While industrial areas had the highest concentrations of heavy metals such as Fe, Zn and Cr and also the $\text{SO}_{4}^{2-}$ ions, traffic areas with relatively higher traffic densities in the city endured highest concentrations of Cd and the $\text{NO}_{3}^{-}$ ion. As gaseous pollutants serve as precursors of ionic particles in the atmospheric environment, gaseous pollution control is necessitated along with particulate with special reference to heavy metal and ion pollution abatement for the sustainable development of Madurai city.     

基于X射线荧光分析原理的大气重金属在线分析仪的维护与质控

近年来大气细颗粒物中重金属元素成分的监测是细颗粒物化学成分监测的热点之一,这一类物质的在线监测在国内应用越来越多,笔者研究和探讨了影响X射线荧光法大气重金属在线分析仪器运行质量的主要运维工作和质量控制方法,提出了该仪器在线监测中的运维及质控要求,为环境监测工作者提供参考,以获得更加准确的监测数据。