2013—2021年新疆乌鲁木齐市电磁环境水平调查与分析

为了解新疆乌鲁木齐市电磁环境水平及影响,开展了电磁环境水平调查,以具有代表性的区域点位为调查对象,2013—2021年电磁环境监测结果表明,乌鲁木齐市射频综合电场强度整体呈现逐年增加的趋势,年平均值从2013年的0.54 V/m上升到了2021年的1.31 V/m,但所有监测点位测值均远低于《电磁环境控制限值》(GB ...     

北京市中心商区射频电磁环境测试与分析

各类无线技术的发展和应用导致公众曝露于环境中的电磁场辐射的程度越来越高,由此引发的对人体健康风险的担忧促使诸多国家和组织开展了相关研究,并制定了电磁环境控制限值,电磁环境的空间分布也成为至关重要的基础数据。于2019年10—12月对北京市中心3个典型商区的电磁环境进行了测试,测试频段为10 MHz～8 GHz,属于射频范围。通过空间插值方法对测试数据进行处理,从而得到测试区域的射频电磁环境空间分布地图。对测试数据的进一步分析表明,测试区域的射频电磁环境水平主要分布在0.5～2.5 V/m,随空间距离变化较为剧烈,总体上符合《电磁环境控制限值》(GB 8702—2014)的要求。建议在城市发展过程中,对射频电磁环境进行持续、精细的监测。     

雄安新区环境电磁辐射水平初步监测

对雄安新区电磁辐射水平进行监测和分析,结果表明：该地区一般环境电场强度为未检出~1.03 V/m,基站周围电场强度为0.36 V/m~1.08 V/m,广播电视塔周围电场强度为0.65 V/m~3.19 V/m,均低于《电磁环境控制限值》（GB 8702—2014）中对公众暴露控制限值的要求。表明雄安新区电磁辐射水平总体良好,处于正常环境本底水平。     

江西省通信基站电磁环境现状调查分析

通过对江西省2012—2014年监测的4 781个具有代表性的通信基站电磁环境数据统计,从行政区域、城乡环境和发展趋势等角度分析江西省通信基站电磁环境质量与管理现状。结果表明,江西省通信基站电磁环境影响整体控制在较低水平,98.7%的通信基站周边电磁环境功率密度4.0×10-2W/m2,可同时也面临部分通信基站周边公众活动区域电磁环境强度较高、电磁环境整体水平快速增强、中心城区通信基站电磁环境管理困难等问题。     

基于相位差的多系统通信基站的电磁辐射监测

在安徽宣城通信基站中选取103个基站并设置924个监测点位,用电磁辐射分析仪监测,利用相位差确定所属区域后对基站电磁辐射强度作理论预测,与现场监测值对比分析。结果表明,现场监测电场强度值为0. 20 V/m～1. 86 V/m,均值为0. 45 V/m;功率密度为0. 011μW/m~2～0. 918μW/m~2,均值为0. 063μW/m~2,远小于标准限值。说明该区电磁环境状况整体较好,基站周围电磁辐射随着距离的增大而不断减小,功率密度实测值变化趋势与理论预测值基本一致。     

厦门市电磁环境解析

为了掌握厦门市电磁环境状况,于2014—2015年对厦门市进行网格分区季度监测,由监测数据发现厦门市区的电磁辐射强度较低,其整体电磁环境监测值符合《电磁环境控制限值》(GB 8702—2014)标准的要求。不同区域低频磁感应强度呈现工业区商业区文教居住区旅游风景区的特点,其中商业区、文教居住区比总体平均水平(0.181μT)略低;射频电磁辐射呈现工业区商业区旅游风景区文教居住区的特点,商业区、旅游风景区的平均辐射强度比较接近,接近平均水平(0.73 V/m);运用主成分法分析电场和磁场分布的综合特征,分布表现为4个主成分;还发现了4代不同代际移动通信信号的分布规律,一代、二代手机代表通讯频段信号强度更高,强信号覆盖的范围也更大;三代手机代表通讯频段信号在中心城区、商业区和个别旅游风景区较强;四代手机代表通讯频段信号在中心城区和商业区较强。     

南昌市秋季大气PM2.5中金属元素污染及生态风险评价

2013年秋季采集了南昌市6个不同功能区的大气PM_(2.5)样品,分析了PM_(2.5)含量及其中18种金属元素的含量。结果表明:采样期间南昌市大气PM_(2.5)平均质量浓度均在《环境空气质量标准》(GB 3095—2012)日平均浓度限值二级标准规定(75μg/m3)的范围内。PM_(2.5)中多数金属元素的含量水平低于中国内地城市,而与香港和国外城市相比则偏高。分别采用富集因子法和潜在生态风险指数法对重金属污染风险进行了评价。富集因子法表明Zn、Pb、Hg、Cu等元素富集程度较高,Cd富集程度极高,人为源显著;潜在生态风险指数法表明Pb、Hg、Cd潜在生态风险程度为极强,南昌市总体潜在生态风险表现为极强,2种方法的评价结果较为一致。     

德阳市农用地土壤中镉的分布特征及异常来源分析

通过龙门山区域的德阳市6个县市农用地土壤中镉的采样监测,分析了该区域镉的分布特征及区域分异原因,并对其环境生态风险进行了评价。结果表明,德阳市农用地土壤中镉含量总体水平为0.11~4.68 mg/kg,呈现西北到东南逐渐降低的分布特征;西北部绵竹和什邡市农用地土壤中镉出现超标的范围较广,2个城市约62.5%的监测点土壤中镉出现超标,且绵竹市农用地土壤中镉超标程度和生态风险程度最重,绵竹地区约25%的监测点土壤中镉出现了轻中度超标;监测区域土壤中镉出现较重生态风险点共有4个,均出现在绵竹;但较高含量的镉在该区域并非大范围连片存在;区域农用地土壤中镉异常的来源主要为龙门山中段的地质背景和部分以矿石为原料企业的综合影响。     

黄土高原土壤母质中的稀土元素背景值研究

一、样品采集 采样点分布于黄土高原北纬34°到38°,东径103°到112°的黄土沉积区(图1)。采样点的选取是在黄土及土壤的分布基础上随机布点。63个土壤剖面的分配为黄绵土22个,黑垆土18个,(土娄)土10个,灰钙土7个,灰褐土7个。所有土壤剖面均按其发生层次采样。三个典型黄土地质剖面分设在不同黄土地带,按其黄土沉积时序及古土壤发生层次取样。其中35个古土壤的下伏黄土作为不同地带的典型黄土,用以和现代土壤的黄土母质比较。     

某农药厂周边空气毒死蜱污染状况及健康风险评价

为了研究某农药厂毒死蜱生产对周围人群产生的潜在健康风险,在农药厂周围村庄设置采样点,采用大流量大气采样器采集大气样本,索式提取/气相色谱法分析毒死蜱浓度。结果表明,大气气溶胶中毒死蜱的质量浓度为0.2~189 ng/m3,大气颗粒物中毒死蜱浓度较低,质量浓度为ND~3.50 ng/m3。基于美国环保局推荐的健康风险评价方法计算结果表明,大气毒死蜱暴露对于儿童和成人的非致癌风险控制在EPA推荐的可接受风险水平。     

Monitoring the changes in impervious surface ratio and urban heat island intensity between 1987 and 2011 in Szeged,Hungary

Landsat time series data make it possible to continuously map and examine urban land cover changes and effects on urban environments. The objectives of this study are (1) to map and analyse an impervious surface and its changes within a census district and (2) to monitor the effects of increasing impervious surface ratios on population and environment. We used satellite images from 1987, 2003 and 2011 to map the impervious surface ratio in the census district of Szeged, Hungary through normalized spectral mixture analysis. Significant increases were detected from 1987 to 2011 in industrial areas (5.7–9.1%) and inner residential areas (2.5–4.8%), whereas decreases were observed in the city centre and housing estates due to vegetation growth. Urban heat island (UHI) values were derived from the impervious surface fraction map to analyse the impact of urban land cover changes. In 2011, the average value in the industrial area was 1.76 °C, whereas that in the inner residential area was 1.35–1.69 °C. In the city centre zones and housing estates, values ranging from 1.4 to 1.5 °C and from 1.29 to 1.5 °C, respectively, were observed. Our study reveals that long-term land cover changes can be derived at the district level from Landsat images and that their effects can be identified and analysed, providing important information for city planners and policy makers.     

The spatial statistics formalism applied to mapping electromagnetic radiation in urban areas

Determining the electromagnetic radiation levels in urban areas is a complicated task. Various approaches have been taken, including numerical simulations using different models of propagation, sampling campaigns to measure field values with which to validate theoretical models, and the formalism of spatial statistics. In the work, we present here that this latter technique was used to construct maps of electric field and its associated uncertainty from experimental data. For this purpose, a field meter and a broadband probe sensitive in the 100-kHz–3-GHz frequency range were used to take 1,020 measurements around buildings and along the perimeter of the area. The distance between sampling points was 5 m. The results were stored in a geographic information system to facilitate data handling and analysis, in particular, the application of the formalism of spatial statistical to the analysis of the distribution of the field levels over the study area. The spatial structure was analyzed using the variographic technique, with the field levels at non-sampled points being interpolated by kriging. The results indicated that, in the urban area analyzed in the present work, the linear density of sampling points could be reduced to a distance which coincides with the length of the blocks of buildings without the statistical parameters varying significantly and with the field level maps being reproduced qualitatively and quantitatively.     

Evaluating the urban climate of a typically tropical city of northeastern Brazil

This study attempted to assess a bioclimate index and the occurrence of an urban heat island in the city of Campina Grande, northeastern Brazil, using data taken from mobile measurements and Automatic Weather Stations (AWS). The climate data were obtained during two representative months, one for the dry season (November 2005) and one for the rainy season (June 2006) at seven points in an urban area. Ten-minute air temperatures recorded by an AWS installed in urban areas were compared to those from a similar station located in a suburban area to assess the urban heat island (UHI). The data were collected using a 23X data logger (Campbell Scientific, Inc.) programmed for collecting data every second. The thermal discomfort level was analyzed by Thom’s discomfort index (DI), and an analysis of variance was applied for assessing if there was any statistically significant difference at the 1% and 5% significance level of thermal comfort among points. Mann–Kendall statistical test was used for identifying possibly significant trends in a time series for air temperature, relative humidity, and class A pan evaporation for the city of Campina Grande. The present study found UHI intensities of 1.48°C and ??0.7°C for the months taken as representative of the dry and rainy seasons, respectively. Summer in the city has partially comfortable conditions while the winter is fully comfortable. There are significant changes in DI hourly values between seasons. Only during the rainy season did all points of the city have a comfortable condition until 8:19 h, at which time they become partially comfortable for the rest of the day. Results indicated that there was a 1.5°C increase in air temperature and a 7.2% reduction in relative humidity throughout the analyzed time series. The DI also showed a statistically significant increasing trend (Mann–Kendall test, p?<?0.01) for the dry and rainy seasons and annual period of approximately 1°C in the last 41 years in the city of Campina Grande.     

Deposition fluxes of PCDD/Fs in the area surrounding a steel plant in northwest Italy

The paper aims at investigating the contribution of a steel plant located in a rural area in northwestern Italy (700,000 tons of steel/year) to the deposition fluxes of Polychorinated Dibenzo-p-dioxins and Polychorinated dibenzofurans (PCDD/PCDFs) at local level through the analysis of sampling data, literature data, and air dispersion model (AERMOD)output data. Total measured deposition fluxes of PCDD/PCDFs in three monitoring stations were consistent with other studies carried out in Italy in urban and suburban areas and in rural European areas; while these were lower than those measured in other European urban/suburban areas or in sites influenced by industrial sources. Furthermore, the measured fluxes were also compared with the pattern of PCDD/Fs in ambient air sampled at the same sites in a previous study. This comparison showed a similarity between air concentration and deposition patterns of the samples collected at the three monitoring stations and a clear distinction of these from the source. The study was completed with AERMOD simulations, conducted with a mass mean particle diameter of 0.5 μm, according to the particle size distribution of the samples collected at the source. AERMOD calculated deposition fluxes of two to three orders of magnitude lower than those measured in two monitoring points; while in the most distant monitoring station, the deposition fluxes were too low to be calculated by the model. The simulations confirmed that the most distant monitoring station was not subject to emissions from the steel plant. The analysis highlighted the limited influence of the source in the local PCDD/F deposition fluxes.     

重庆市住宅楼环境电磁辐射的初步测量与分析

初步探测重庆市住宅楼环境电磁辐射的现状及其影响因素,为建立人居环境电磁场特征数据库提供依据。按照国家标准的要求和方法,在重庆市选择4个典型居住小区,分别测量各小区住宅楼不同楼层电梯门口或楼梯间以及各住宅楼楼顶的电磁辐射水平,结果表明,本次横断面调查中,在1MHz～40GHz频段,各栋楼的综合场强为17.13～17.18V/m,已接近GB 8702-88《电磁辐射防护规定》的公众照射导出限值,各楼层间差异无统计学意义(P>0.05)。在5～1000Hz频段,各栋楼楼内综合场强分布差异无统计学意义(P>0.05),而临近高压线的住宅楼楼顶综合场强明显高于其他小区楼顶以及同一栋楼其他楼层的综合场强(P<0.05),并且该楼各楼层的磁场强度明显高于其他住宅楼(P<0.05)。所测住宅楼的环境电磁辐射水平未超出国家相应标准限制,不同楼层电磁辐射水平与极低频辐射源的分布有关。     

Simulation of mixing depths incorporating the urban heat island effect

The main objective of this paper was to establish the effect of anthropogenic heat flux on the formation of mixing depth specially in urban areas. In this study an energy balance mixing depth model was developed for the simulation of mixing depth incorporating the heat island effect. To demonstrate the effect of heat island, mixing depths were simulated under two conditions. Under the first condition, hourly gridded anthropogenic heat flux and variant surface characteristics were considered, while under the second condition anthropogenic heat flux term was ignored and constant surface characteristics were considered throughout the modelling domain. The release of anthropogenic heat flux in the urban environment was found to be responsible for the growth of the unstable layer in the lower atmosphere even during the night. This resulted in higher mixing depth values in urban areas compared to the surrounding countryside. The maximum differential surfaces sensible heat flux between urban and rural areas was estimated as 130 W/m². From the simulation of mixing depth, it was revealed that the maximum increment in mixing depth in urban areas was 300 m due to the heat island effect. This increment in mixing depth in urban areas can provide an extra space for dilution and mixing of pollutants.     

工程数学数理统计中的抽样理论在城市环境噪声监测优化布点中的应用探讨

用工程数学数理统计中的抽样论研究城市环境噪声监测优化布点,探讨以较少的监测点的测试数据反映整个城区的噪声水平,从而推动环境噪声监测技术的发展     

Monitoring of glyphosate and AMPA in soil samples from two olive cultivation areas in Greece: aspects related to spray operators activities

The persistence of glyphosate and its primary metabolite AMPA (aminomethylphosphonic acid) was monitored in two areas in Southern Greece (Peza, Crete and Chora Trifilias, Peloponnese) with a known history of glyphosate use, and the levels of residues were linked to spray operators’ activities in the respective areas. A total of 170 samples were collected and analysed from both areas during a 3-year monitoring study. A new method (Impact Assessment Procedure - IAP) designed to assess potential impacts to the environment caused by growers’ activities, was utilised in the explanation of the results. The level of residues was compared to the predicted environmental concentrations in soil. The ratio of the measured concentrations to the predicted environmental concentrations (MCs/PECs) was >?1 in Chora the first 2 years of sampling and <?1 in the third year, whilst the MCs/PECs ratio was <?1 in Peza, throughout the whole monitoring period. The compliance to the instructions for best handling practices, which operators received during the monitoring period, was reflected in the amount of residues and the MCs/PECs ratio in the second and especially the third sampling year. Differences in the level of residues between areas as well as sampling sites of the same area were identified. AMPA persisted longer than the parent compound glyphosate in both areas.     

Monitoring of bioaerosol inhalation risks in different environments using a six-stage Andersen sampler and the PCR-DGGE method

Increasing evidences show that inhalation of indoor bioaerosols has caused numerous adverse health effects and diseases. However, the bioaerosol size distribution, composition, and concentration level, representing different inhalation risks, could vary with different living environments. The six-stage Andersen sampler is designed to simulate the sampling of different human lung regions. Here, the sampler was used in investigating the bioaerosol exposure in six different environments (student dorm, hospital, laboratory, hotel room, dining hall, and outdoor environment) in Beijing. During the sampling, the Andersen sampler was operated for 30 min for each sample, and three independent experiments were performed for each of the environments. The air samples collected onto each of the six stages of the sampler were incubated on agar plates directly at 26 °C, and the colony forming units (CFU) were manually counted and statistically corrected. In addition, the developed CFUs were washed off the agar plates and subjected to polymerase chain reaction (PCR)-denaturing gradient gel electrophoresis (DGGE) for diversity analysis. Results revealed that for most environments investigated, the culturable bacterial aerosol concentrations were higher than those of culturable fungal aerosols. The culturable bacterial and fungal aerosol fractions, concentration, size distribution, and diversity were shown to vary significantly with the sampling environments. PCR-DGGE analysis indicated that different environments had different culturable bacterial aerosol compositions as revealed by distinct gel band patterns. For most environments tested, larger (>3 μm) culturable bacterial aerosols with a skewed size distribution were shown to prevail, accounting for more than 60 %, while for culturable fungal aerosols with a normal size distribution, those 2.1–4.7 μm dominated, accounting for 20–40 %. Alternaria, Cladosporium, Chaetomium, and Aspergillus were found abundant in most environments studied here. Viable microbial load per unit of particulate matter was also shown to vary significantly with the sampling environments. The results from this study suggested that different environments even with similar levels of total microbial cuturable aerosol concentrations could present different inhalation risks due to different bioaerosol particle size distribution and composition. This work fills literature gaps regarding bioaerosol size and composition-based exposure risks in different human dwellings in contrast to a vast body of total bioaerosol levels.