Speciation and ecological risk of heavy metals in intertidal sediments of Quanzhou Bay, China

The chemical speciation of nine heavy metals in intertidal sediments from Quanzhou Bay was determined using a modified sequential extraction procedure, proposed by the Commission of the European Community Bureau of Reference. The results show that Mn presents the highest percentage in the acid-soluble fraction, and Pb and Cu present the highest percentages in the reducible fraction. The highest percentages of Fe, V, Cr, Ni, Zn, and Co were found in the residual fraction. The mobility order of the heavy metals studied on the basis of the nonresidual content of the elements is Mn > Pb > Cu > Co > Zn > Ni > Cr > V > Fe. The assessment on potential ecological risk indices of some heavy metals indicates that Zn, Ni, and Cr show moderate contamination, while Cu and Pb show slighter contamination. On the whole, the comprehensive potential ecological risk index of Cu, Zn, Ni, Cr, and Pb in the sediments presents moderate degree.     

Total concentrations, fractionation and mobility of heavy metals in soils of urban area of Guwahati, India

This work describes the results of assessment of the heavy metals, Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn in urban soil of Guwahati City, India from 31 sites of five different land use types covering residential, commercial, industrial, public utilities, and roadside. Sequential extraction procedure was used to evaluate the relative distribution of the eight metals in exchangeable, carbonate, reducible (Fe?CMn oxide), organic and sulfide, and residual fractions. Of the eight metals, Cd and Co occur in lower concentrations (Cd <?< Co) in all types of land, and concentration variation from one type of land use to another is not much significant for both the metals. Ni presence is more than Co, and the concentrations show some variation depending on land use status. Average Cr and Cu concentrations are ??100?mg/kg, but Cr has a significantly higher presence in industrial land use. The results are similar in case of Pb. The two metals, Mn and Zn have domination over the other metals, and the values are ??300?mg/kg. Industrial and roadside soil contains much more Mn, while commercial soil is most enriched with Zn. Of the metals, Ni has the largest proportion (~42%) bound to the exchangeable fraction and Co, Cr, and Pb also have appreciable proportion bound to the same fraction. A significant amount of Co is associated with carbonates. The reducible fraction has bound considerable quantity of Mn and Zn, while most of Cu is associated with the organic and sulfide fraction. Both Cd and Pb are dominantly associated with the residual fraction. Computation of the mobility factor of the metals indicates Mn to be the most mobile metal present in the soil samples.     

Associations of cadmium, zinc, and lead in soils from a lead and zinc mining area as studied by single and sequential extractions

An exploratory study of the area surrounding a historical Pb?CZn mining and smelting area in Zawar, India, detected significant contamination of the terrestrial environment by heavy metals. Soils (n?=?87) were analyzed for pH, EC, total organic matter (TOM), Pb, Zn, Mn, and Cd levels. The statistical analysis indicated that the frequency distribution of the analyzed parameters for these soils was not normal. The median concentrations of metals in surface soils were: Pb 420.21 ?? g/g, Zn 870.25 ?? g/g, Mn 696.70 ?? g/g, and Cd 2.09 ?? g/g. Zn concentrations were significantly correlated with Cd (r?=?0.867), indicating that levels of Cd are dependent on Zn. However, pH, electrical conductivity and total organic matter were not correlated significantly with Cd, Pb, Zn, and Mn. To assess the potential mobility of Cd, Pb, and Zn in soils, single (EDTA) as well as sequential extraction scheme (modified BCR) were applied to representative (n?=?23) soil samples. The amount of Cd, Pb, and Zn extracted by EDTA and their total concentrations showed linear positive correlation, which are statistically significant (r values for Cd, Pb, and Zn being 0.901, 0.971, and 0.795, respectively, and P values being <0.001). The correlation coefficients indicate a strong relation between EDTA-extractable metal and total metal. These results appear to justify the use of ??total?? metal contents as a useful preliminary indicator of areas where the risks of metal excess or deficiency are high. The EDTA extractability was maximum for Cd followed by Pb and Zn in soils from all the locations. As indicated by single extraction, the apparent mobility and potential bioavailability of metals in soils followed the order: Cd ?? Pb >?> Zn. Soil samples were sequentially extracted (modified BCR) so that solid pools of Cd, Zn, and Pb could be partitioned into four operationally defined fractions viz. acid-soluble, reducible, oxidizable, and residual. Cadmium was present appreciably (39.41%) in the acid-soluble fraction and zinc was predominantly associated (32.42%) with residual fraction. Pb (66.86%) and Zn (30.44%) were present mainly in the reducible fraction. Assuming that the mobility and bioavailability are related to solubility of geochemical forms of metals and decrease in the order of extraction, the apparent mobility and potential metal bioavailability for these contaminated soil samples is Cd > Zn > Pb.     

Geochemical fractionation of trace elements in sediments of Hugli River (Ganges) and Sundarban wetland (West Bengal, India)

A sequential extraction procedure was carried out to determinate the concentrations of 11 elements (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn) in different geochemical phases of sediments collected along the Hugli (Ganges) River Estuary and in the Sundarban mangrove wetland, eastern coastal part of India. The chemical speciation of elements was determined using the three-step sequential extraction procedure described by the European Community Bureau of Reference. Total metal concentration was determined using a microwave-assisted acid digestion procedure. Metal concentrations were near the background level except for As for which a moderate pollution can be hypothesized. The mobility order of the metals was: Cd?>?Mn?>?Cu?>?Zn?>?As?>?Co?>?Pb?>?Ni?>?Fe?>?Cr?>?Al. The highest percentage of Cd (>60%) was found in the most labile phase. Residual fraction was prevailing for Fe, Cr and Al, while Pb was mainly associated with the reducible fraction. Data were compared with Sediment Quality Guidelines to estimate the relationship between element concentrations and adverse biological effects on benthic community, finding the possibility of some toxic effects due to the presence of As in the entire studied area and Cd, only in Calcutta.     

Levels and speciation of heavy metals in soils of industrial Southern Nigeria

A knowledge of the total content of trace metals is not enoughto fully assess the environmental impact of polluted soils. Forthis reason, the determination of metal species in solution isimportant to evaluate their behaviour in the environment andtheir mobilization capacity. Sequential extraction procedure wasused to speciate five heavy metals (Cd, Pb, Cu, Ni and Zn) fromfour contaminated soils of Southern Nigeria into sixoperationally defined geochemical species: water soluble,enchangeable, carbonates, Fe-Mn oxide, organic and residual.Metal recoveries were within ± 10% of the independentlydetermined total Cd, Pb, Cu, Ni and Zn concentrations. The highest amount of Cd (avg. 30%) in the nonresidual fractionswas found in the exchangeable fraction, while Cu and Zn weresignificantly associated with the organic fraction. Thecarbonate fraction contained on average 14, 18.6, 12.6, 13 and11% and the residual fraction contained on average 47, 18, 33,50 and 25% of Cd, Pb, Cu, Ni and Zn respectively. Assuming thatmobility and bioavailability of these metals are related to thesolubility of the geochemical form of the metals, and that theydecrease in the order of extraction sequence, the apparentmobility and potential bioavailability for these five metals inthe soil were: Pb > Zn > Cu > Ni > Cd. The mobility indexes ofcopper and nickel correlated positively and significantly withthe total content of metals, while mobility indexes of cadmiumand zinc correlated negatively and significantly with the totalcontent of metals.     

Distribution and solid-phase speciation of toxic heavy metals of bed sediments of Bharali tributary of Brahmaputra River

Heavy metal (Fe, Mn, Zn, Cu, Ni, Pb, and Cd) concentrations and their chemical speciations were investigated for the first time in bed sediments of Bharali River, a major tributary of the Brahmaputra River of the Eastern Himalayas. Levels of Fe, Mn, Pb, and Cd in the bed sediments were much below the average Indian rivers; however, Cu and Zn exhibit levels on the higher side. Enrichment factors (EF) of all metals was greater than 1 and a higher trend of EF was seen in the abandoned channel for most metals. Pb showed maximum EF of 32 at site near an urban center. The geoaccumulation indices indicate that Bharali river is moderately polluted. The metals speciations, done by a sequential extraction regime, show that Cd, Cu, and Pb exhibit considerable presence in the exchangeable and carbonate fraction, thereby showing higher mobility and bioavailability. On the other hand, Ni, Mn, and Fe exhibit greater presence in the residual fraction and Zn was dominant in the Fe?CMn oxide phase. Inter-species correlations at three sites did not show similar trends for metal pairs indicating potential variations in the contributing sources.     

Pollution in the urban soils of Lianyungang,China, evaluated using a pollution index,mobility of heavy metals,and enzymatic activities

Soil samples from 16 urban sites in Lianyungang, China were collected and analyzed. A pollution index was used to assess the potential ecological risk of heavy metals and a sequential extraction procedure was used to evaluate the relative distribution of Cu, Zn, Pb, Cd, Cr, and As in exchangeable, carbonate, Fe/Mn oxide, organic/sulfide, and residual fractions. The mobility of heavy metals and urease (URE) activity, alkaline phosphatase (ALP) activity, and invertase (INV) activity of soils was determined. The results showed that the average concentrations of Cu, Zn, Pb, Cd, Cr, and As in Lianyungang soils were much higher than those in the coastal city soil background values of Jiangsu and China. Among the five studied regions (utilities, commercial, industrial, tourism, and roadside), the industrial region had the highest metal concentrations demonstrating that land use had a significant impact on the accumulation of heavy metals in Lianyungang soils. Compared to the other metals, Cd showed the highest ecological risk. According to chemical partitioning, Cu was associated with the organic/sulfides and Pb and Zn were mainly in the carbonate and the Fe/Mn oxide phase. The greatest amounts of Cd were found in exchangeable and carbonate fractions, while Cr and As were mainly in the residual fraction. Cd had the highest mobility of all metals, and the order of mobility (highest to lowest) of heavy metals in Lianyungang soils was Cd > Zn > Pb > Cu > As > Cr. Soil urease activity, alkaline phosphatase activity, and invertase activity varied considerably in different pollution degree sites. Soil enzyme activities had the lowest levels in roadside and industrial regions. Across all the soil data in the five regions, the total Cu, Zn, Pb, Cd, Cr, and As level was negatively correlated with urease activity, alkaline phosphatase activity, and invertase activity, but the relationship was not significant. In the industrial region, alkaline phosphatase activity had significant negative correlations with total Cu, Pb, Cr, Zn, Cd, and heavy metal fractions. This showed that alkaline phosphatase activity was sensitive to heavy metals in heavily contaminated regions, whereas urease and invertase were less affected. The combination of the various methods may offer a powerful analytical technique in the study of heavy metal pollution in street soil.     

Assessment of background levels of trace metals in water and soil from a remote region of Himalaya

Selected trace metals were estimated by atomic absorption spectrometry in the water and soil samples collected from the remote region of Himalaya. The soil samples were analysed for soluble and acid extractable fraction of trace metals. In water samples, Ca, Na, Mg and K emerged as dominant contributors, whereas, Ca, Na, K, Mg, Fe and Pb were estimated at comparatively higher levels in the water extract of the soil. In case of acid extract of the soil samples, Ca, K, Fe, Mg, Mn and Na were found at elevated concentrations. Based on mean levels of the metals, following decreasing concentration order was observed in water samples: Ca > Na > Mg > K > Pb > Co > Cu > Zn > Mn > Cr > Fe > Cd > Li, however, in the acid extract of the soil, following order was noted: Ca > K > Fe > Mg > Mn > Na > Pb > Zn > Cr > Li > Cu > Co > Cd. The correlation study revealed appreciably diverse mutual relationships of trace metals in the water and soil samples. The multivariate cluster analyses exhibited divergent apportionment of trace metals in water and soil samples. Among the trace metals, Cd, Pb, Li, Zn, Cr, Cu, Mn and Co exhibited extreme to significant anthropogenic enrichment in the soil samples, while the rest of the metals were mostly contributed by the natural processes.     

Dissolved and particulate metals in water from Sonora Coast: a pristine zone of Gulf of California

The purpose of this study was to investigate the distribution of metals (Cd, Pb, Hg, Cu, Fe, Mn, and Zn) in dissolved and particulate fractions in seawater from Bacochibampo Bay, Northern part of Mexico. Water samples were collected from November 2004 to October 2005. Metal analysis was done by graphite furnace atomic absorption spectroscopy. Results indicated highest concentrations of dissolved Cd and Zn in the sites localized at the mouth and center of the bay. During summer and spring, the highest levels of Cd, Mn, and Fe were detected, Zn in fall, and Pb and Cu in winter and spring. Mercury was the only metal that was not found in this fraction. In particulate fraction, Fe, Hg, and Mn were the most abundant elements in all the sampling sites, followed by Zn, Cu, Pb, and Cd. The highest levels of the majority of the metals were observed in the coastline, suggesting a continental and/or urban source for these chemicals. The highest level of Cd was detected during the summer and the rest of the metals in the fall. Statistically significant correlations were observed between dissolved and particulate forms of Pb:Mn, Cu:Fe, and Cu:Mn. The mean partition coefficient values were as follows: Fe>Mn>Cu>Pb>Cd>Zn. All dissolved metal concentrations found, except Pb, were lower than EPA-recommended water quality values. The levels of dissolved metals in this study reveal low bioavailability and toxic potential. However, further toxicological and sediment chemistry studies in this area are needed for a full risk assessment.     

Heavy metal contamination in water, soil, and vegetables of the industrial areas in Dhaka, Bangladesh

Concentrations of Cu, Zn, Pb, Cr, Cd, Fe, and Ni have been estimated in soils and vegetables grown in and around an industrial area of Bangladesh. The order of metal contents was found to be Fe > Cu > Zn > Cr > Pb > Ni > Cd in contaminated irrigation water, and a similar pattern Fe > Zn > Ni > Cr > Pb > Cu > Cd was also observed in arable soils. Metal levels observed in different sources were compared with WHO, SEPA, and established permissible levels reported by different authors. Mean concentration of Cu, Fe, and Cd in irrigation water and Cd content in soil were much above the recommended level. Accumulation of the heavy metals in vegetables studied was lower than the recommended maximum tolerable levels proposed by the Joint FAO/WHO Expert Committee on Food Additives (1999), with the exception of Cd which exhibited elevated content. Uptake and translocation pattern of metal from soil to edible parts of vegetables were quite distinguished for almost all the elements examined.