Development of a simple extraction cell with bi-directional continuous flow coupled on-line to ICP-MS for assessment of elemental associations in solid samples

A continuous-flow system comprising a novel, custom-built extraction module and hyphenated with inductively coupled plasma-mass spectrometric (ICP-MS) detection is proposed for assessing metal mobilities and geochemical associations in soil compartments as based on using the three step BCR (now the Measurements and Testing Programme of the European Commission) sequential extraction scheme. Employing a peristaltic pump as liquid driver, alternate directional flows of the extractants are used to overcome compression of the solid particles within the extraction unit to ensure a steady partitioning flow rate and thus to maintain constant operationally defined extraction conditions. The proposed flow set-up is proven to allow for trouble-free handling of soil samples up to 1 g and flow rates < or =10 mL min(-1). The miniaturized extraction system was coupled to ICP-MS through a flow injection interface in order to discretely introduce appropriate extract volumes to the detector at a given time and with a given dilution factor. The proposed hyphenated method demonstrates excellent performance for on-line monitoring of major and trace elements (Ca, Mn, Fe, Ni, Pb, Zn and Cd) released when applying the various extracting reagents as addressed in the BCR scheme, that is, 0.11 M CH(3)COOH, 0.1 NH(2)OH.HCl and 30% H(2)O(2), even when a well recognized matrix-sensitive detector, such as ICP-MS, is used. As a result of the enhanced temporal resolution of the ongoing extraction, insights into the breaking down of phases and into the kinetics of the metal release are obtained. With the simultaneous multielement detection capability of ICP-MS, the dynamic fractionation system presents itself as an efficient front-end for evaluation of actual elemental association by interelement comparison of metals leached concurrently during the extraction time. Thus, the intimate elemental association between Cd and Zn in contaminated soils could be assessed.     

Metal Leachability and Anthropogenic Signal in Roadside Soils Estimated from Sequential Extraction and Stable Lead Isotopes

Several roadside soil samples were collected at two field sites in Sweden. They were analysed for total elemental content (using both ICP-MS and XRF) and stable lead isotopes. Extraction with deicing salt solution and sequential extraction were performed in order to elucidate the potential mobility due to the use of deicing agents. The total concentrations of elements, especially lead, have decreased and lead is presently almost at background concentrations (15-51 ppm for surface samples). However, the isotopic signature indicates that old gasoline lead still is left at the site constructed prior to 1975. The field site constructed in 1992 showed, however, no 206Pb/207Pb ratio below 1.14. Only minor amounts were leached using deicing salt solutions; for lead only 0.29%, on average, was extracted indicating that the mobile fraction already was released. Sequential extraction indicated that lead mainly was associated with reducible (34.4%) and oxidisable (35.4%) fractions. Exchangable and acid soluble fractions contained 20.3% while 10.0% was found in the residual fraction. The salt extraction released, however, very low concentrations indicating that most in fraction 1 is acid soluble (e.g. carbonates). Tungsten was also found at high concentrations indicating a possible impact from studded tires. For tungsten the following composition was obtained: residual (48.0%) > oxidisable (47.6%) > reducible (3.3%) > exchangeable/acid soluble (1.1%). From the isotopic studies it was also suggested that the order for incorporating anthropogenic lead into soils is exchangeable/carbonates > (hydr)oxides > organic matter > residual. The multivariate technique principal component analysis (PCA) seems promising for evaluating large sequential extraction datasets.     

气相色谱-质谱法测定废酸油渣中的16种多环芳烃

建立了废酸油渣中16种多环芳烃超声萃取、Florisil萃取柱净化、气相色谱-质谱测定的方法。笔者对提取方式、提取剂类型和体积、提取时间和次数、净化方式等进行研究,采用无水硫酸钠分散,二氯甲烷作为提取剂超声40 min,提取液经纯水清洗、离心后取适量有机相经过3 g Florisil萃取柱净化,采用气相色谱-质谱选择离子模式(SIM),加入内标进行定量分析。结果表明:二氯甲烷提取效率比正己烷好,丙酮可能引起酸性样品中多环芳烃的降解,丙酮超声萃取时加入无水硫酸钠能在一定程度上防止目标物降解,但萃取效率不可控制,宜采用二氯甲烷作为萃取剂。分散提取能有效减少提取时间,超声清洗仪超声40 min提取效率为86.2%～104%。3g Florisil萃取柱净化比1 g Florisil萃取柱净化和GPC净化效果略好。方法检出限为0.4～1.3 mg/kg,6次空白加标的相对标准偏差为2.3%～15.3%,6个实际样品测定结果的相对标准偏差为1.2%～27.3%,基体加标回收率为51.3%～126%,连续校准稳定。该方法适用于废酸油渣样品中16种多环芳烃的检测,比直接溶解有效,比加速溶剂萃取、索氏提取、微波萃取和超声探头萃取简单、快捷,能有效减少设备污染和腐蚀,净化方法有效,测定结果准确可靠,是实现大批量样品检测的可行方法。     

固相萃取-高效液相色谱法同时测定水中12种磺酰脲类除草剂

采用固相萃取-高效液相色谱法同时测定水中12种磺酰脲类除草剂,样品经磷酸调节pH值为2后,经Watens Oasis HLB SPE柱净化浓缩,乙腈洗脱,选择检测波长为230 nm,以乙腈-水溶液(0.02%磷酸)为流动相梯度洗脱,保留时间在14 min～32 min范围内.12种磺酰脲类除草剂在0.050 mg/L～...     

Investigation of arsenic speciation on drinking water treatment media utilizing automated sequential continuous flow extraction with IC-ICP-MS detection

Three treatment media, used for the removal of arsenic from drinking water, were sequentially extracted using 10 mM MgCl2(pH 8), 10 mM NaH2PO4(pH 7) followed by 10 mM (NH4)2C2O4(pH 3). The media were extracted using an on-line automated continuous extraction system which allowed the arsenic in each of the extraction fluids to be speciated on-line using IC-ICP-MS. The 10 mM MgCl2 preferentially extracted As(III) from each of the media. The percentage of the arsenic extracted by the MgCl2, relative to a HNO3/H2O2 digestion of the media, ranged from 0.1-2.3% for the three solids. The next sequential extraction fluid, 10 mM NaH2PO4, extracted some of the residual As(III) remaining on each of the media but the predominant species extracted was As(V). The 10 mM NaH2PO4 extracted 15.3 to 42.8% of the total arsenic relative to a total digested concentration for each of the media. The As(III) and As(V) stability studies conducted in these two extraction fluids indicated that conversion between As(III) and As(V) was not significant for the short extraction fluid sample contact time associated with the on-line continuous flow extraction cell. Finally, the 10 mM (NH4)2C2O4 extraction fluid was utilized in an off-line analysis mode because the Fe and As concentrations extracted from the media were not compatible with direct ICP-MS detection. The (NH4)2C2O4 extracted 2.9-29% As(III) for all three media and caused an oxidation of As(III) to As(V) during the extraction period for one of the three media. The sum of the arsenic from each of the three extraction fluids represented 92%, 44% and 53% of the available total arsenic for the three media, respectively. The speciation results for each media were obtained by adding all the speciation results from all three extraction fluids together and the resulting distribution of As(III)/As(V) compared well with the speciation results obtained via XANES.     

Guidelines for evaluating selenium data from aquatic monitoring and assessment studies

It is now possible to formulate diagnostic selenium concentrations in four distinct ecosystem-level components; water, food-chain, predatory fish (consuming fish or invertebrate prey), and aquatic birds. Waterborne selenium concentrations of 2 µg/l or greater (parts per billion; total recoverable basis in 0.45 filtered samples) should be considered hazardous to the health and long-term survival of fish and wildlife populations due to the high potential for food-chain bioaccumulation, dietary toxicity, and reproductive effects. In some cases, ultra-trace amounts of dissolved and particulate organic selenium may lead to bioaccumulation and toxicity even when total waterborne concentrations are less than 1 µg/l.Food-chain organisms such as zooplankton, benthic invertebrates, and certain forage fishes can accumulate up to 30 µg/g dry weight selenium (some taxa up to 370 µg/g) with no apparent effect on survival or reproduction. However, the dietary toxicity threshold for fish and wildlife is only 3 µg/g; these food organisms would supply a toxic dose of selenium while being unaffected themselves. Because of this, food-chain organisms containing 3 µg/g (parts per million) dry weight or more should be viewed as potentially lethal to fish and aquatic birds that consume them.Biological effects thresholds (dry weight) for the health and reproductive success of freshwater and anadromous fish are: whole body=4 µg/g; skeletal muscle=8 µg/g; liver=12 µg/g; ovaries and eggs=10 µg/g. Effects thresholds for aquatic birds are: liver=10 µg/g; eggs=3 µg/g. The most precise way to evaluate potential reproductive impacts to adult fish and aquatic bird populations is to measure selenium concentrations in gravid ovaries and eggs. This single measure integrates waterborne and dietary exposure, and allows an evaluation based on the most sensitive biological endpoint. Resource managers and aquatic biologists should obtain measurements of selenium concentrations present in water, food-chain organisms, and fish and wildlife tissues in order to formulate a comprehensive and conclusive assessment of the overall selenium status and health of aquatic ecosystems.     

Evaluation of performance of time-saving extraction devices in the BCR three-step sequential extraction procedure

Two alternative extraction methods--a routine ultrasonic bath and a microwave oven--were developed and optimized for their eventual exploitation in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (S, M & T) Programme, formerly Bureau Communitaire de Reference (BCR), for the operationally defined speciation of Cd, Cr, Cu, Ni and Zn. The conventional BCR three-stage sequential extraction procedure was modified at each stage, applying ultrasonic or microwave devices in order to shorten the required 16 h of shaking in all three steps. The experimental tests and the optimization of the operating parameters were carried out on a highly homogenized estuarine sediment reference material (RM S7) prepared by the Joint Research Centre (JRC) of ISPRA. Extractable metal contents were measured by inductively coupled plasma-mass spectrometry (ICP-MS) and the results obtained in each fraction by all three methods were statistically compared for all the studied elements. The conventional and newly developed alternative extraction methods were finally compared by the analysis of BCR 601, which is certified for the three-step BCR sequential extraction procedure. According to the statistical evaluation of the results, the proposed accelerated sequential extraction methods are valid alternatives to conventional shaking, with much shorter extraction times.     

异丙醇增感电感耦合等离子体质谱法直接测定土壤和沉积物中硒

提出了沸水浴混合酸法消解,以异丙醇为增感剂,电感耦合等离子体质谱直接测定土壤和沉积物中硒的方法。实验表明2mol/L硝酸-4mol/L盐酸混酸能有效溶出土壤和沉积物中各种形态的硒。相对于1%硝酸基体,4%(V/V)异丙醇基体中硒的ICP-MS响应值提高了12.1倍;而且4%(V/V)异丙醇基体可有效抑制硒的质谱干扰。ICP发射功率和雾化气流速是影响异丙醇在ICP-MS测定过程增敏效应的主要因素。以78硒为测定同位素,方法检出限为0.005mg/kg,实际样品测定精密度均小于5%。用于测定土壤和沉积物国家标准样品并对其消解液进行加标回收实验,结果令人满意。     

Occurrence of naproxen,ibuprofen, and diclofenac residues in wastewater and river water of KwaZulu-Natal Province in South Africa

The present paper reports a detailed study that is based on the monitoring of naproxen, ibuprofen, and diclofenac in Mbokodweni River and wastewater treatment plants (WWTPs) located around the city of Durban in KwaZulu-Natal Province of South Africa. Target compounds were extracted from water samples using a multi-template molecularly imprinted solid-phase extraction prior to separation and quantification on a high-performance liquid chromatography equipped with photo diode array detector. The analytical method yielded the detection limits of 0.15, 1.00, and 0.63 μg/L for naproxen, ibuprofen, and diclofenac, respectively. Solid-phase extraction method was evaluated for its performance using deionized water samples that were spiked with 5 and 50 μg/L of target compounds. Recoveries were greater than 80% for all target compounds with RSD values in the range of 4.1 to 10%. Target compounds were detected in most wastewater and river water samples with ibuprofen being the most frequently detected pharmaceutical. Maximum concentrations detected in river water for naproxen, ibuprofen, and diclofenac were 6.84, 19.2, and 9.69 μg/L, respectively. The concentrations of target compounds found in effluent and river water samples compared well with some studies. The analytical method employed in this work is fast, selective, sensitive, and affordable; therefore, it can be used routinely to evaluate the occurrence of acidic pharmaceuticals in South African water resources.     

NPD与FPD气相色谱法测定水中的黄磷

实验采用优化条件,对甲苯萃取水和废水中黄磷进行测定。萃取液经气相色谱仪毛细色谱柱分离后,氮磷检测器（NPD）或火焰光度检测器（FPD,带磷滤光片）检测,根据色谱峰的保留时间定性,外标法定量。使用NPD检测器分析时,本方法检出限为0.04μg/L;使用FPD检测器分析时,本方法检出限为0.1μg/L。     

超声波提取-GC/MS法测定生物体内硝基苯类化合物

以洪泽湖中6种代表性生物为研究对象，采用超声波法提取样品中硝基苯类化合物，用凝胶色谱净化、浓缩，气相色谱／质谱联用法测定。该法与索氏提取法在同等试验条件下进行加标回收试验，前者回收率高且稳定，简便可行。方法检出限为0．008μg／g～0．030μg／g，平均加标回收率为76．5％～109％，重复测定3次的RSD为1．5％～13．0％。     

Optimizing the removal of carbon phases in soils and sediments for sequential chemical extractions by coulometry

We have developed a coulometric technique to optimize the removal of the carbonate and organic fractions for sequential chemical extractions of soils and sediments. The coulometric system facilitates optimizing these two fractions by direct real-time measurement of carbon dioxide (CO2) evolved during the removal of these two fractions. Further analyses by ICP-MS and alpha-spectrometry aided in interpreting the results of coulometry experiments. The effects of time, temperature, ionic strength and pH were investigated. The sensitivity of the coulometric reaction vessel/detection system was sufficient even at very low total carbon content (< 0.1 mol kg-1). The efficiency of the system is estimated to be 96% with a standard deviation of 8%. Experiments were carried out using NIST Standard Reference Materials 4357 Ocean Sediment (OS), 2704 Buffalo River Sediment (BRS), and pure calcium carbonate. Carbonate minerals were dissolved selectively using an ammonium acetate-acetic acid buffer. Organic matter was then oxidized to CO2 using hydrogen peroxide (H2O2) in nitric acid. The carbonate fraction was completely dissolved within 120 min under all conditions examined (literature suggests up to 8 h). For the OS standard, the oxidation of organic matter self-perpetuates between 45 and 50 degrees C, a factor of two less than commonly suggested, while organic carbon in the BRS standard required 80 degrees C for the reaction to proceed to completion. For complete oxidation of organic matter, we find that at least three additions of H2O2 are required (popular methods suggest one or two).     

全自动Ｃ１８膜萃取－气相色谱法测定水中卤代醚

使用全自动固相萃取仪、C18膜-毛细管气相色谱-电子捕获检测器的分析方法检测水中具有致癌性的卤代醚，回收率范围71．8％～126％，检出限0．5～1．5μg／L，与EPA611相比，更加快速、准确，能够满足我国饮用水和废水的分析要求。     

Leaching Characteristics of Heavy Metals and As from Two Urban Roadside Soils

The leaching tests, including the Toxicity Characteristic Leaching Procedure (TCLP), EDTA extraction and BCR sequential extractions before and after EDTA treatments, were performed on two specific soils to elucidate heavy metal-associated mineral fractions and general leachability. The TCLP illustrated the low leachability of heavy metals in soils from two sites. EDTA is a strong chelator and therefore had higher extraction efficiency compared to that of TCLP. The lower extraction percentages by EDTA for As and Sb were found compared to the other heavy metals derived from anthropogenic sources. Sequential extractions showed that the importance of acid-extractable, organically-bound and Fe–Mn oxide fractions was identified for anthropogenic heavy metals with the exception of As and Ni while the importance of residual fraction was identified for endogenous metals. Changes in sequential fractions of heavy metals after leaching with EDTA are very complex and it is difficult to generalize on which fraction was more mobile than the others. These combined results are helpful in elucidating the association of heavy metals to soil fractions and the mobility characteristics of heavy metals under certain environmental conditions.     

Conventional, microwave, and ultrasound sequential extractions for the fractionation of metals in sediments within the Petrochemical Industry, Serbia

In this paper, the main objective was fractionation of Cd, Cu, Ni, Pb, Zn, Ca, Fe, and K in certificate material and sediment samples gathered from and around the Petrochemical Industry using the conventional, microwave and ultrasonic sequential extraction. Microwave oven and ultrasound bath were used as an energy source for achieving faster extraction. Additional heating and boiling of samples were avoided by using lower power and shorter time for microwave and ultrasound extraction. Precision and accuracy of procedure were evaluated by using certificate material (BCR701). Acceptable accuracy of metals (87.0–111.3 %) was achieved for all three-step sequential of conventional extraction protocol. An accuracy of the fourth step has been verified with two certificate materials: BCR143R and 146R. The range of total extracted metal concentrations from sediments was similar for all three extraction techniques. A significant high percentage of Cd, Cu, and Zn were obtained after extraction of the exchangeable and acid soluble sediment fraction. Principal component analysis of values obtained after determination of risk assessment code using conventional and ultrasound sequential extraction show similarity of these values. Accuracy, recovery, and risk assessment code values imply that ultrasound sequential extraction is a more suitable, accelerated sequential extraction procedure (30 min per extraction step) than microwave extraction in applied conditions.     

Investigation on chemical species of arsenic, selenium and antimony in fly ash from coal fuel thermal power stations

Investigations of the existing chemical forms and the concentrations of arsenic (As), selenium (Se) and antimony (Sb) in samples of fly ash obtained from six coal-fired power stations in various countries were carried out. The concentration of As was found to vary from 5.4 to 22.3 mg kg(-1), and the most common mode of occurrence of As in the fly ashes is in association with carbonates or Fe-Mn oxides. The concentrations of Se and Sb ranged from 2.3-5.2 and 1.0-3.9 mg kg(-1), respectively. The dominant chemical forms of Se and Sb in the fly ashes were as extractable species. Also, water-soluble As, Se and Sb in the fly ashes were extracted, and the chemical species of As, Se and Sb in the extract determined using HPLC-ICP-MS. This was done as the potential release of soluble As, Se and Sb through leaching of fly ash is of environmental concern. The most abundant form of As in the extract was the low toxicity As(V). The main species of Se was Se(IV), although it was found that the ratio of Se(VI) to Se(IV) in acidic fly ashes is higher than in alkaline fly ash samples. Antimony was mostly present as Sb(III).     

Determination of arsenic species in fish, crustacean and sediment samples from Thailand using high performance liquid chromatography (HPLC) coupled with inductively coupled plasma mass spectrometry (ICP-MS)

Suitable techniques have been developed for the extraction of arsenic species in a variety of biological and environmental samples from the Pak Pa-Nang Estuary and catchment, located in Southern Thailand, and for their determination using HPLC directly coupled with ICP-MS. The estuary catchment comprises a tin mining area and inhabitants of the region can suffer from various stages of arsenic poisoning. The important arsenic species, AsB, DMA, MMA, and inorganic arsenic (As III and V) have been determined in fish and crustacean samples to provide toxicological information on those fauna which contribute to the local diet. A Hamilton PRP-X100 anion-exchange HPLC system employing a step elution has been used successfully to achieve separation of the arsenic species. A nitric acid microwave digestion procedure, followed by carrier gas nitrogen addition- (N2)-ICP-MS analysis was used to measure total arsenic in sample digests and extracts. The arsenic speciation of the biological samples was preserved using a Trypsin enzymatic extraction procedure. Extraction efficiencies were high, with values of 82-102%(As) for fish and crustacean samples. Validation for these procedures was carried out using certified reference materials. Fish and crustacean samples from the Pak Pa-Nang Estuary showed a range for total arsenic concentration, up to 17 microg g(-1) dry mass. The major species of arsenic in all fauna samples taken was AsB, together with smaller quantities of DMA and, more importantly, inorganic As. For sediment samples, arsenic species were determined following phosphoric acid (1 M H3PO4) extraction in an open focused microwave system. A phosphate-based eluant, pH 6-7.5, with anion exchange HPLC coupled with ICP-MS was used for separation and detection of AsIII, AsV, MMA and DMA. The optimum conditions, identified using an estuarine sediment reference material (LGC), were achieved using 45 W power and a 20 minute heating period for extraction of 0.5 g sediment. The stability and recovery of arsenic species under the extraction conditions were also determined by a spiking procedure which included the estuarine sediment reference material. The results show good stability for all species after extraction with a variability of less than 10%. Total concentrations of arsenic in the sediments from the Pak Pa-Nang river catchment and the estuary covered the ranges 7-269 microg g(-1)and 4-20 [micro sign]g g(-1)(dry weight), respectively. AsV was the major species found in all the sediment samples with smaller quantities of AsIII. The presence of the more toxic inorganic forms of arsenic in both sediments and biota samples has implications for human health, particularly as they are readily 'available'.     

固相萃取-GC/MS法测定水中16种有机氯农药

采用HLB固相萃取柱富集水样,乙酸乙酯溶剂洗脱,加入氘代菲作为内标,利用气相色谱/质谱联用法选择离子模式测定水中16种有机氯农药,优化了固相萃取条件。16种有机氯农药在5.00μg/L~250μg/L范围内线性良好,按1 L水样计算,方法最低检出限为1.4 ng/L~19.4 ng/L,相对标准偏差为3.5%~20.0%,平均加标回收率为44.7%~119%。     

Determination of rotenoids and piperonyl butoxide in water, sediments and piscicide formulations

Rotenone is a naturally occurring insecticide and piscicide (fish poison) found in many leguminous plants. This paper describes high-performance liquid chromatography (HPLC) methods for the quantitative analysis of rotenone's principal biologically active components (rotenone, tephrosin, rotenolone, deguelin) and the synergist piperonyl butoxide (PBO) in various media. Compounds were separated on a C18 reversed phase column with an acetonitrile-0.025 M phosphoric acid mobile phase and detected by UV absorbance or fluorescence (PBO only). Solid phase extraction (SPE) was used in either coupled (on-line) mode with a C18 concentrator column or automated off-line mode using Empore C18 disks. The on-line extraction efficiency was improved significantly by adding small amounts of methanol to water. Method detection limits (MDLs) for rotenoids and PBO in reagent water were 0.3 and 2 micrograms L-1, respectively, with optimal recoveries ranging from 90% to 99%. Aquatic sediments were extracted with methanol and the extracts were diluted in water prior to analysis by coupled SPE-HPLC. In wet sediments, detection limits were approximately 20-100 micrograms kg-1 with recoveries of 71% to 87%. Sonication in dimethyl sulfoxide (DMSO) followed by dilution in acetonitrile and filtration allowed determination of the active ingredients in powdered rotenone formulations. Details of sample preparation, cartridge column cleanup and analyte confirmation are provided.     

快速溶剂萃取—气相色谱法分析土壤中的20种有机氯

采用加速溶剂萃取—气相色谱法对土壤中20种有机氯农药进行了提取测定.通过改变加速溶剂萃取条件,选取了最佳条件参数,减少了组份的损失;通过改变气相色谱条件,使得20种有机氯农药快速分离.该方法具有操作简便、灵敏度高、检出限低、快速、溶剂消耗少等优点,方法检出限为1.23～ 3.11 μg/kg,实际样品的加标回收率为62.3％～119.7％.