EDTA络合滴定法测定硫酸盐化速率

碱片硫酸盐化速率的分析过程是将碱片上的硫酸盐溶解 ,转移到水中 ,然后测定水溶液中硫酸根的含量。 EDTA络合滴定法测定硫酸盐化速率 ,是在转移的水溶液中加入过量的氯化钡溶液 ,使硫酸根与钡离子产生硫酸钡沉淀 ( Ksp=1.1× 10 - 10 ) ,过量的钡离子用 EDTA溶液滴定 ,差量法测硫酸根含量。该方法在我国环境监测中属创新监测分析方法 ,在天津、上海、江苏、四川、广东等地有所应用 ,其中所用试剂比重量法少 ,时间短 ,操作方法简单 ,准确度和精密度较重量法高。1　原理将吸收了二氧化硫的碱片加水浸泡 ,使硫酸根溶出 ,上清液用盐酸酸化 …     

离子色谱法测定碱片上的SO_4~(2-)离子

本文研究离子色谱法测定硫酸盐化速率,用碱片采集大气中含硫化合物(主要是二氧化硫)。碱片上的硫酸盐经淋洗液洗脱、过滤后、直接进入离子色谱仪测定SO_4~(2-)离子浓度。检出下限为0.2ppm,本法适用于颗粒物中可溶性SO_4~(2-)离子的测定。     

EDTA络合滴定法测定硫酸盐化速率

将碱片的硫酸盐溶解到水中，加入过量的氯化物溶液，使产生硫酸钡沉淀，过量钡离子用ＥＤＴＡ溶液滴定，差量法测出硫酸根含量，从而得到硫酸盐化速率量。     

碱片—离子色谱法测定大气中硫酸盐化速率方法探讨

实验证实碱片－离子色谱测定大气中硫酸盐化速率方法操作简便快速，准确可靠，最低检出浓度可达０．１ｍｇ／Ｌ，可替代碱片－重量法测定。     

碱片——离子色谱法测定大气硫酸盐化速率

由于硫酸盐化速率值更能客观地反映大气中含硫污染物的污染状况,因此,它成为环境大气监测的必测项目之一。目前主要采用的测定方法有二氧化铅—重量法,碱片—重量法和碱片—比浊法等。本文通过实验表明,改用碱片—离子色谱法测定大气硫酸盐化速率,不仅方法准确可靠,而且操作简便快速。本方法的检出限为0.05毫克SO_3/100厘米~2碱片·日。     

淋洗液体系对碱片-离子色谱法测定硫酸盐化速率影响研究

分别用碳酸根淋洗液体系和氢氧根淋洗液体系碱片-离子色谱法对硫酸盐化速率样品进行比对试验。结果表明,2种淋洗液体系在0.00~20.0 mg/L质量浓度范围内线性良好,标准曲线相关系数均> 0.999,检出限、精密度、准确度和测定结果都没有显著性差异,说明这2种淋洗液体系方法是等效的。采用氢氧根淋洗液体系分析硫酸盐化速率,可配备淋洗液发生器,背景更低,实验操作步骤更少,工作效率更高,建议作为首选方法。     

陕西省城镇污水处理厂进出水中主要离子与重点元素分布特征

污水处理厂出水中主要离子和重点元素的浓度特征及去除效果会影响受纳水体的盐度、碱度等指标,从而影响河湖的生态服务功能,但是这方面的研究长期以来未得到充分关注。在陕西省全境选择51家城镇污水处理厂,测定进水和出水中的钾、钙、钠、镁、氟、氯和硫酸根离子,以及铁、锰、硼、钼、锶等重点元素的浓度。测定结果显示:陕西省城镇污水处理厂进水和出水中的阳离子以钠离子为主,其次是钙、镁离子,钾离子浓度最低;阴离子中,氯离子浓度最大,其次为硫酸根离子。就总离子浓度而言,陕北和关中地区污水处理厂进水的离子浓度普遍高于陕南地区。相关性分析结果显示:在污水处理厂进水中,钠、氟、氯、镁及硫酸根离子相互之间均呈现显著正相关关系;铁、锰在进水中没有表现出明显的相关关系,而在出水中呈现显著的正相关关系。污水处理厂仅能够处理污水中少量的氟、钾和镁离子。铁元素和锰元素在经过污水处理厂的处理后,浓度有所升高。此研究的研究结果可为河湖水化学组成管理决策提供参考。     

离子色谱法测定水中亚硫酸根的优化

为了提高离子色谱法测定水中亚硫酸根的准确性,通过条件实验,对亚硫酸根稳定性、淋洗液有机改进剂等进行优化。选择Metrosep A Supp 5150色谱柱,以3.2 mmol/L的碳酸钠+1.0 mmol/L的碳酸氢钠+5.0%的丙酮溶液为淋洗液,经离子色谱检测,亚硫酸盐的质量浓度在0~10.0 mg/L范围内与色谱峰面积线性关系良好,检出限为0.034 mg/L。实际样品测定结果的相对标准偏差为2.4%~4.7%,加标回收率为96.8%~103%。该方法可延长亚硫酸盐标准溶液的保存时间,有效分离亚硫酸根和硫酸根,灵敏度高、正确度与精密度良好,适用于水中亚硫酸根的测定。     

碱片法硫酸盐化速率测定的改良

《环境监测分析方法》规定以碱片法测定硫酸盐化速率时,选用了硫酸钡称重法或硫酸钡比浊法。前者操作繁琐,测定周期较长,含量较低时,称量误差偏大。后者则操作要求严格,有较多的因素影响校准曲线的线性和测定的精密度。 我们采取《降水化学成分监测方法(试行)》中硫酸盐的测定方法,免去二苯碳酰二肼显色,由反应生成的黄色铬酸根离子直接进行比色,并对操作步骤作了一些改动,以适合碱片法测定硫酸盐化速率,取得较满意的结果。     

铵离子对COD测定的干扰及干扰的消除方法

水样中只存在铵离子时对COD的测定几乎没有影响,而当铵离子与氯离子同时存在时,除了氯离子带来的干扰外,铵离子也会对COD的测定产生干扰。针对此现象,研究建立了加碱氮吹法,此法可有效去除COD测定中浓度小于1 000 mg/L铵离子的干扰,并确定了最佳除铵离子条件为过量加碱、600 m L/min的氮气流量和3 h的通气时间。通过7次平行测定含铵离子干扰物的水样,该方法的相对标准偏差为3.3%~6.5%,加标回收率为90.2%~97.0%,表明方法具有较好的精密度和准确度,能够较准确测定含有铵离子干扰水样的COD。     

24 h diffusive sampling of toxic VOCs in air onto Carbopack X solid adsorbent followed by thermal desorption/GC/MS analysis-laboratory studies

Diffusive sampling of a mixture of 42 volatile organic compounds (VOCs) in humidified, purified air onto the solid adsorbent Carbopack X was evaluated under controlled laboratory conditions. The evaluation included variations in sample air temperature, relative humidity and ozone concentration. Linearity of samples with loading was examined both for a constant concentration with time varied up to 24 h and for different concentrations over 24 h. Reverse diffusion and its increase with accumulation of sample were determined for all compounds. Tubes were examined for blank levels, change of blanks with storage time, and variability of blanks. Method detection limits were determined based on seven replicate samples. Based on this evaluation, 27 VOCs were selected for quantitative monitoring in the concentration range from approximately 0.1 to 4 ppbv. Comparison results of active and diffusive samples taken over 24 h and under the same simulated ambient conditions at a constant 2 ppbv were interpreted to estimate the effective diffusive sampling rates (ml min(-1)) and their uncertainties and to calculate the corresponding diffusive uptake rates (ng ppmv(-1) min(-1)).     

离子色谱法测定地表水中总氮

采用碱性过硫酸钾消解水样，OnGuardⅡBa柱萃取、过滤，去除消解液中大量硫酸盐，离子色谱法测定地表水中总氮含量。试验表明，方法在0ms／L～20．0mg／L之间线性良好，相关系数r为0．9994，方法检出限为0．007mg／L。该方法与国标法同时测定标准物质，测定值均在定值范围内，6次平行测定结果的RSD分别为2．3％和1．8％，地表水样的加标回收率为95．7％～105％。实际水样的测定结果与国标法比对，无明显差异。     

搅拌棒萃取-热脱附/气质联用法测定水中2-MIB和土臭素

采用搅拌棒萃取-热脱附/气质联用法测定水中2-甲基异莰醇和土臭素，优化了搅拌棒萃取和热脱附进样的条件。试验表明：两种目标化合物在1．00 ng/L～200 ng/L范围内线性良好，2-甲基异莰醇的相关系数为0．9993，土臭素的相关系数为0．9997，方法检出限分别为0．31 ng/L和0．15 ng/L；空白和实际样品的加标回收率为82．4％～116％，测定结果的RSD＜10％。     

COD测定中对低浓度硫酸亚铁铵溶液标定的研究

在COD水样测定过程中,以滴定后的空白样品为介质,加入定量的重铬酸钾标准溶液对低浓度硫酸亚铁铵溶液进行标定,经校正后的标定结果显示,精密度和准确度均良好。采用此方法既省略操作步骤、节约实验试剂,同时又节省工作时间。     

主动采样法采集博物馆空气中微量污染气体

根据博物馆污染气体的种类,对气体主动采样法进行了采样器种类、吸收液种类和浓度、吸收液体积的选择。验证了气体采样流量、采样时间与气体采样浓度的线性关系,确定了酸性和碱性污染气体的主动采样方法,为监测文物保存环境污染气体提供了可行方法。     

Workplace aerosol mass concentration measurement using optical particle counters

Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM? 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO?) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions calculated from the OPC data are closely correlated with the results of the particle size-selective sampling using the CIP 10. Furthermore, the OPC data allow calculation of the thoracic fraction of workplace aerosol (not measured by sampling), which is interesting in the presence of allergenic particles like fungi spores. The results also show that the modified COP inlet adequately samples inhalable aerosol in the range of workplace particle-size distribution.     

Concentration gradient patterns of aerosol particles near interstate highways in the Greater Cincinnati airshed

The objective of this study was to determine if there is an exposure gradient in particulate matter concentrations for people living near interstate highways, and to determine how far from the highway the gradient extends. Air samples were collected in a residential area of Greater Cincinnati in the vicinity of two major highways. The measurements were conducted at different distances from the highways by using ultrafine particle counters (measurement range: 0.02-1 microm), optical particle counters (0.3-20 microm), and PM2.5 Harvard Impactors (0.02-2.5 microm). The collected PM2.5 samples were analyzed for mass concentration, for elemental and organic carbon, and for elemental concentrations. The results show that the aerosol concentration gradient was most clearly seen in the particle number concentration measured by the ultrafine particle counters. The concentration of ultrafine particles decreased to half between the sampling points located at 50 m and 150 m downwind from the highway. Additionally, elemental analysis revealed a gradient in sulfur concentrations up to 400 m from the highway in a residential area that does not have major nearby industrial sources. This gradient was qualitatively attributed to the sulfate particle emissions from diesel engine exhausts, and was supported by the concentration data on several key elements indicative of traffic sources (road dust and diesel exhaust). As different particulate components gave different profiles of the diesel exposure gradient, these results indicate that no single element or component of diesel exhaust can be used as a surrogate for diesel exposure, but more comprehensive signature analysis is needed. This characterization is crucial especially when the exposure data are to be used in epidemiological studies.     

Microsoft Word for Windows在环境质量报告书中的应用

叙述了ＭｉｃｒｏｓｏｆｔＷｏｒｄｆｏｒＷｉｎｄｏｗｓ软件在编写环境质量报告书中的应用内容。     

Simultaneous extraction of bromide, chloride, fluoride and sulfate from soils, waste- and building materials

The simultaneous extraction of bromide, chloride, fluoride and sulfate was studied in soils, waste- and building materials. Acid, neutral and alkaline extractants were used; 0.01 mol l(-1) H(3)PO(4), milliQ-water and 0.01 mol l(-1) NaOH, respectively. The extracts were analysed by ion chromatography and ion selective electrode. Extracted concentrations were compared with the amount obtained by an alkaline smelt, as an approximation of the total extractable content. The results indicate that there is a significant difference in extraction behaviour between waste- and building materials and soils. Bromide and chloride were in general completely extracted from the former solid materials, but less than 10% and 50%, respectively, from soils. Fluoride is strongly bound in all investigated samples; less than 10% of the total content was extracted with any of the three extractants. The fraction of extracted sulfate varied between 4 and 87% of the total content, and was in general larger in waste- and building materials than in soils. Differences in extracted concentration between the 3 extractants occurred mainly for fluoride and sulfate. Extracted bromide was similar with all three extractants and extracted chloride showed differences for the various soil samples only. Increasing the NaOH concentration up to 1 mol l(-1) resulted mainly in an increase of extracted amount of fluoride and for soils also in extracted amounts of bromide and sulfate. Although, the results show that the composition of the solid material strongly influences the final pH of the extract and the extracted amount of investigated anions, application of Milli-Q water as an extractant might be a very fruitful option within the development of the Dutch Building Materials Decree.     

Pesticide vapours in confined atmospheres. Determination of dichlorvos by SPME-GC-MS at the microg m(-3) level

A method based on SPME is described for assessing the gaseous dichlorvos concentration in confined atmospheres like a greenhouse after a pesticide application. Sampling was made by using SPME with PDMS fibres immersed into a 250 mL sampling flask into which air samples were dynamically pumped from the analysed atmosphere. Sampling duration was 40 min and samples were then analysed by GC-MS. Calibration was performed from a vapour saturated air sample and gas phase diluted samples, and this procedure afforded a curve with a regression coefficient (R2) higher than 0.98. The repeatability of these measurements was observed with an RSD of 2.5%. This analysis procedure was then applied for the determination of gaseous dichlorvos concentrations versus time, in the atmosphere of an experimental 8 m2 and 20 m3 greenhouse. The pesticide was sprayed according to real cultivation conditions and measurements were made from 2 up to 74 h after application affording observed concentrations in the range of decades and hundreds of microg m(-3) (corresponding limits of detection and quantification were found at the level of a few microg m(-3)).