固定污染源废气中氟化物监测的探讨

废气固定污染源氟化物监测已有方法标准,但在实际工作中仍会遇到一些现有标准未具体规定但又严重影响监测结果的问题。文章主要针对固定污染源废气中氟化物监测时采样管的选择以及在高湿烟气中的测试进行了一些探讨,对实际工作具有指导作用。     

固定污染源废气监测中有关问题的探讨

针对废气固定污染源监测中存在的一些疑难问题，从工况的确定、断面的选择、间断排放的监测时间、滤筒及过剩系数的影响等方面进行了探讨，提出了一些解决办法。     

地面水评价工作中COD测定的探讨

在环境影响评价中,对地面水COD本底量低,流量大、稀释能力强的河流进行评价时,测定过程较小的误差都将影响到评价报告的质量。 某厂环境影响评价通过污染源分析和掌握的资料,对污染源受纳主体沅江5公里水域进行了三天(其中第二天连续24小时)连续采样。共设置了对照、污染和消减共五个断面,选定了以COD为主的评价方法。建立了污染物沿水流方向的平衡方程式:     

塞曼原子吸收光谱法测定固定污染源废气中的汞

用PMS 30B型汞采样器采集固定污染源废气,再用塞曼原子吸收汞分析仪测定样品中的汞,高、低浓度汞标准样品测定结果均在标准范围内,相对误差分别为0和4.3%。汞吸收管对高、低浓度含汞废气的穿透效率表明,当废气汞质量浓度达到mg/m3级别时,穿透率仅为1.3%。用该方法测定稳定工况固定污染源废气中的汞,6次测定结果的RSD为5.9%,方法检出限为1.04 ng,当采样体积为20 L时,检出限为0.05μg/m3。实际监测表明,钢铁企业、燃煤电厂、垃圾焚烧厂废气中汞为0.07μg/m3~1 031μg/m3。     

便携式振荡天平法现场测定固定污染源废气中颗粒物的研究

将振荡天平技术与国内污染源废气监测方法标准相结合,建立了废气中颗粒物现场测定方法--便携式振荡天平法。新建方法以重量法为原理,检出限为0.2 mg/m 3,全程伴热以消除湿度干扰,测试前后以标准滤膜量值验证的方式对称量结果进行质量保证,实现了固定污染源废气中颗粒物的快速、准确的测量。方法建立后与国标法《固定污染源废气低浓度颗粒物的测定重量法》(HJ 836—2017)进行实际样品测定比对,结果表明,2种方法无显著性差异。新建方法提高了工作效率,减少了过程误差。     

CO对定电位电解法测定SO2的影响及对策探讨

采用定电位电解法测定固定污染源废气中SO2,根据CO标准气体干扰SO2 测定的规律建立数学模型,并在实验室用CO标气对数学模型进行验证.用该数学模型对5家企业固定污染源废气中SO2 监测,将测定结果与碘量法的测定结果比对,绝对误差与相对误差在允许范围内.     

浅析国控废气污染源在线比对监测存在的问题及对策——以镇江市为例

以镇江市国控废气污染源在线比对监测为例,分析了国控废气污染源比对监测存在的典型问题,从监测规范、比对方法、运维管理等角度剖析原因,提出,合理设置手工与在线监测点位,减少比对监测方法干扰因素,加强在线监测仪器维护监督管理等建议,从而提高比对监测合格率,更好地开展国控污染源在线比对监测工作。     

排放源烟道气二噁英空间分布对监测结果的影响

针对生活垃圾焚烧企业烟气排放烟囱6个断面单点采样的试验结果,分析按照《固定污染源排气中颗粒物测定与气态污染物采样方法》(GB/T 16157—1996)多断面点采样与单一固定断面点采样对监测结果的影响。试验表明,烟道气在不同断面点质量浓度分布差异较大,相对于样品实际监测值,各断面点二噁英毒性当量浓度最大正偏差达到+306%,最大负偏差达到-96%,测定的18个断面点样品,只有2个样品与实际样品监测值相近。     

VOCs在线监测进样方式对非甲烷总烃测定的影响

采用正压、负压、大气平衡3种进样方式，研究了VOCs在线监测系统对非甲烷总烃测定的影响。探讨在大气平衡进样方式下定量环内压力、平衡时间、进样流量对非甲烷总烃测定的影响，研究结果表明：采用正压进样方式，定量环内正压增大，非甲烷总烃质量浓度偏高；采用负压进样方式，定量环内负压增大，非甲烷总烃质量浓度降低；采用大气平衡进样方式，定量环内压力、平衡时间、进样流量的增大或减小对非甲烷总烃测定没有明显影响。比较3种进样方式，大气平衡进样方式的VOCs在线监测系统能够提高非甲烷总烃在线监测结果的准确性和可靠性，更适用于污染源废气在线监测。     

高通量固定污染源废气颗粒物中总汞的测定

用玻璃纤维滤筒采集固定污染源废气颗粒物,借助硝酸和氢氟酸的作用,使滤筒和废气颗粒物在160℃下消解,再用原子荧光法测定消解液中总汞。用50%热硝酸溶液处理玻璃纤维滤筒,消除滤筒本底值不一对测定结果的干扰,并优化消解过程,使该方法在0.050μg/L~1.00μg/L范围内线性良好。当采样体积为10 L时,方法检出限为4.5×10~(-5)mg/m~3,空白加标样6次测定结果的RSD为7.2%,加标回收率为87.0%~113%。将该方法用于测定某固定污染源废气颗粒物中总汞,测定值在标准排放限值内。     

环境空气监测点位的管理办法

阐述了加强环境空气监测点位管理的重要性，指出了目前环境空气监测点位管理中存在的问题，提出设置监测点位时，既要考虑监测点的位置和数量，又要考虑监测点周围的人为活动、流动污染源、固定污染源和面源的影响。     

鳌江水污染特征及防治对策

平阳县环境监测站于1998年2002年对鳌江埭头、江屿、方岩渡、江口渡4个断面的水质进行了监测。结果表明，埭头断面目前属尚清洁．江屿断面属严重污染(以氨氮、挥发酚为主)，方岩渡、江口渡断面为中污染段(以氨氮为主)。造成鳌江污染的污染源主要是平阳县的制革废水和鳌江沿岸乡镇的生活污水。提出。环保及各级政府部门应加大对鳌江治理投资，尽快建设排污管网及生活污水处理厂；对无能力进行废水处理的小企业，应予以关闭；提倡使用清洁生产工艺，从源头减少制革废水的污染。     

氯苯类化合物在大气中分布特征探究

建立环境空气和有组织废气排放模拟污染源,以玻璃纤维滤膜+玻璃棉和活性炭为吸附材料采集大气中氯苯类化合物,使用气相色谱法测定各组分,考察氯苯类化合物在大气气相和颗粒物中的分布特征。结果显示,环境空气和固定污染源有组织排放废气中一氯代至四氯代苯类各组分主要分布在大气气相中,颗粒物中少有分布,说明现行环境监测方法以固体吸附剂采集测定大气中的氯苯类化合物可行。     

兰州市汽车尾气污染状况调查

通过对兰州市汽车尾气污染状况的调查与分析，认为兰州市街道空气污染较重，ＣＯ、ＮＯｘ、ＳＯ２、ＴＳＰ、Ｐｂ各项污染均超标，其污染程度与车流强度、时间、季节、路面宽度、风速及不同形式的交通路口相关。汽车尾气排放已成为兰州市空气污染的重要来源。     

The design of long-term air quality monitoring networks in urban areas using a spatiotemporal approach

The implementation and maintenance of an air pollution monitoring program can be expensive and time consuming, especially when the aim is for long-term monitoring over a significant area. Consequently, it is essential that sites are optimized to provide the best representative cover while minimizing costs. In the past, there has been a tendency to locate sampling stations at pollution hot-spots. While this is acceptable for determining a maximum potential exposure or identifying the extent of a risk, there are limitations to this approach when assessing the potential impact of any future abatement strategies or determining the level of exposure outside the vicinity. This paper presents an approach in which representative air quality assessments can be undertaken for an urban area using the minimum number of measurement sites. A novel methodology is described that involves site selection to capture the maximum variance in measured pollutants, while minimizing spatiotemporal autocorrelation between the selected sites. A case study is presented for Yazd, Iran. Overall, the results show that the proposed methodology can be effective and enable the long-term monitoring of air pollution to be undertaken on a cost-effective basis in urban areas. In addition, there is the potential for the methodology to be utilized for other forms of pollution (e.g., water, soil, and noise).     

传感器技术在环境空气监测与污染治理中的应用现状、问题与展望

大气环境污染物监测是建立污染源与环境污染关系的重要技术途径,也是大气综合治理决策所需数据的主要来源。近年来,空气质量精细化管理和污染源精准控制的需求逐渐增长,对监测技术提出了更高的要求。传感器技术作为空气质量监测标准方法的补充,是实现城市空气质量高时空分辨率测量的新手段。研究从传感器的原理及分类入手,通过综述其在环境空气质量监测、污染源监控管理、个人暴露风险评估等领域的应用,总结了传感器技术的研发进展、应用现状和存在问题,并提出其发展方向和前景。     

A Method for Locating Influential Pollution Sources and Estimating Their Contributions

This work develops a source-oriented approach to locate the influential pollution sources and estimate their contributions to pollutant concentrations observed at a receptor site. The domain containing possible influential pollution sources is divided into systematic grid cells, and the influential grid sources are determined based on the locations of the segment endpoints of air trajectories arriving at the receptors. The contribution of each grid source is initially calculated using a formula derived from a Lagrangian box model and including the effects of source emissions, atmospheric dilution, and chemical transformation and deposition. The formula is described in detail in this study. Finally, the average contribution of each grid source is determined based on numerous analyzed events. The proposed approach was used to locate influential pollution sources and determine their contributions to a rural monitoring station during periods of high SO₂ pollution in southern Taiwan. The contributions of sources in various 2 km by 2 km grid cells, five districts, three source categories, 8 industrial areas, and a power plant were evaluated. The results show that the major influential sources were in the northwestern region of south Taiwan, and belonged to three district and point sources. Furthermore, two industrial areas close to the evaluated stations were also very significant, and contributed about 30% of the total pollution.     

典型街道环境空气质量分析

根据对深南东路环境空气的监测及车流量、气象条件的调查,分析机动车及气象因素对深圳市环境空气质量的影响。根据分析可知,机动车尾气是深圳市环境空气中污染物的主要来源,但污染程度不断变化的主要原因是风速,深圳市环境空气中污染物浓度与风速有着非常显著的负相关。     

Combining a road pollution dispersion model with GIS to determine carbon monoxide concentration in Tennessee

The purpose of this paper is to develop an air pollution model that is independent from pollution monitoring sites and highly accurate through space and time. Total carbon monoxide concentration is computed with the use of traffic flow data, vehicle speed and dimensions, emission rates, wind speed, and temperature. The data are interpolated using a geographic information system universal kriging technique, and the end results produce state level air pollution maps with high local accuracy. The model is validated against Environment Protection Agency (EPA) pollution data. Overall, the model has 71 % agreement with EPA, overestimating values of carbon monoxide for less than 1 ppm. The model has three advantages over already assessed air pollution models. First, it is completely independent of any air pollution monitoring stations; thus, possible temporary or permanent unreliability or lack of the data is avoided. Second, being based on a 5,710 traffic count network, the problem of remote places coverage is avoided. Third, it is based on a straightforward equation, where minimal preprocessing of traffic and climatic data is required.     

上海市工业区大气污染预警监测信息平台研究与设计

根据上海市工业区大气污染排放特征,在构建大气特征污染监控网络的基础上,搭建了工业区大气污染预警监测信息平台,并研究了适用于大气特征污染自动站的通信传输规范,确保数据联网和应用。平台设置了大气质量监控、大气数据管理、污染源一厂一档、大气质量分析评价、污染源溯源分析、应急监测数据管理、智能移动终端查询等7个子系统,可为上海市工业区大气污染预警和管控提供实时监测数据。