广东省煤电行业大气铅污染现状分析

采用基于多排放系数的煤电行业大气铅排放量计算方法,计算2011—2013年广东省铅排放量,并分析铅污染的地区分布和排放特征。结果表明:全省煤电行业每年向大气中排放铅污染物80.6 t,占燃煤中含铅总量的3.72%;燃煤铅排放系数呈逐年下降趋势,平均值为6.33 kg/万t;燃煤机组大气铅排放量由高到低分别为珠三角粤东粤西粤北,东莞、广州和江门3市铅排放量最高;铅集中排放强度高的城市大多为沿海城市,大气污染扩散条件较好;山区城市中梅州铅集中排放强度较高,其余城市较低;珠三角出海口主要大气铅排放点源分布密集,易形成区域污染,存在一定风险。     

石家庄市春季大气颗粒物的铅污染特征

为了解石家庄市2016年春季大气颗粒物的铅污染特征及来源,利用单颗粒气溶胶质谱仪(SPAMS),分析了大气中含铅颗粒的化学成分。结果表明: 研究期间大气环境中含铅颗粒数浓度共出现11次跳跃式升高,跳跃时间段内石家庄均处于轻度污染过程。从成分分析来看,含铅颗粒分为纯铅颗粒、Pb与K(Pb-K)、OC(Pb-OC)、Cl(Pb-Cl)、混合颗粒等八大类。观测结果表明:Pb-K颗粒最多,占到含铅颗粒的84.4%；其次为纯铅颗粒,占比为13.0%。与石家庄市污染源谱库比对进行来源解析,得到Pb-K颗粒主要来自生活垃圾焚烧源, 纯铅颗粒主要来自工业源。结合石家庄市大气污染源排放清单和后向气流轨迹分析,推测含铅颗粒可能来自市区西南方向某区县的生活垃圾焚烧企业。     

桂林市细颗粒物部分典型排放源的粒径谱及成分分析

采用在线单颗粒气溶胶质谱技术源解析方法,对桂林市PM2.5典型排放源的粒径和化学成分进行质谱分析,采集燃煤/燃气源、工业工艺源、扬尘源、油烟源4类共计7个典型排放源。结果表明,桂林市4类排放源细颗粒物的粒径分布为0.25~1.25μm,80%以上的细颗粒分布在0.2~1.0μm的小粒径范围,峰值约0.68μm。细颗粒物离子成分含有Na~+、Mg~+、K~+、NH~+4、Fe~+、Pb~+、Cd~+、V~+、Mn~+、Li~+、Al~+、Ca~+、Cu~+、Zn~+、Cr~+、CN~-、PO_3~-、NO_2~-、NO_3~-、Cl~-、SO_4~(2-)、SiO_3~-等成分,桂林市细颗粒物为元素碳、有机碳元素碳、有机碳、富锰颗粒、富铁颗粒、富钾颗粒、矿物质、左旋葡聚糖以及其他金属等9类。     

超低排放下燃煤电厂颗粒物排放特征分析研究

选取6家经过超低排放改造的燃煤电厂,对湿法脱硫(WFGD)和湿式电除尘器(WESP)进出口烟气中TPM、PM_(10)、PM_(2.5)、PM_1进行测试,分析研究超低排放下燃煤电厂颗粒物的排放特征及电除尘器后净化设备对颗粒物的脱除效果。结果表明,6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放浓度分别为0.75~2.36、0.71~2.12、0.65~1.96、0.51~1.57 mg/m~3。分析烟气中颗粒物粒径分布可知,除尘器后,PM10占TPM质量比低于40%,且比例随烟气经过WFGD和WESP而逐渐降低。WFGD对PM2.5有较好的脱除效果,而WESP对PM1脱除效果显著。为满足超低排放标准,6家电厂除尘器后脱除设备综合除尘效率大多在85%以上。计算得到6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放因子,与超低排放改造之前同等级燃煤电厂相比,6家电厂不同粒径颗粒物排放因子均显著降低,也远低于西方发达国家燃煤电厂颗粒物排放因子。     

利用SPAMS初探盘锦市冬季PM2.5污染特征及来源

利用SPAMS 0515于2015年1月在盘锦市兴隆台空气质量自动监测点位采集PM_(2.5)样品,并分析其污染特征和来源。研究结果表明,盘锦市冬季PM_(2.5)的颗粒类型主要以OC颗粒、富钾颗粒、EC颗粒组成。其中,OC颗粒占比最高,为52.5%;PM_(2.5)污染的主要贡献源为燃煤、生物质燃烧、机动车尾气排放,占比分别为33.2%、25.7%、17.5%,特别是在PM_(2.5)质量浓度较高时段,燃煤和机动车尾气排放对污染的贡献较大。     

单颗粒本地排放源谱在上海新冠感染防控期间的监测应用

采用单颗粒飞行时间质谱分析上海市2022年3月—5月新冠感染防控期间大气颗粒物来源，重点关注移动排放源的时空分布规律，并对防控期间、春节期间和防控前正常生产生活期间的监测结果做比对分析。结果表明，防控期间细颗粒物质量浓度较春节期间和正常生产生活时段下降了23.3%；受防控减排措施影响明显的移动源、扬尘、燃煤和工业工艺源排放的细颗粒物质量浓度相较另外两个时段都有不同程度的降低。     

保山市大气细颗粒物排放特征与理化特征分析

于2016年11月9日—14日,用单颗粒气溶胶在线源解析技术分析保山市体育馆监测点大气中PM_(2.5)的化学组成、粒径分布、来源及典型排放源质谱特征。结果表明:采集的颗粒可分为7类,主要以有机碳、元素碳和混合碳颗粒为主,占电离颗粒数的60%以上;不同类型颗粒粒径分布差异较为明显;机动车尾气为首要污染贡献源,且呈周期性变化,每日有两个上升时段,分别为凌晨1:00—10:00和12:00—20:00;其次为燃煤源,贡献率为10%～40%;工艺过程源与生物质燃烧源贡献率相一致,总体上夜间贡献率高于白天;扬尘源、二次无机源贡献率变化幅度不大。     

宁波和温州地区夏季大气中不同粒径颗粒物特征分析

对宁波地区北仑和奉化站、温州地区乐清站3个监测点夏季TSP、PM10、PM2.5和PM1.0进行监测,测试分析各种粒径颗粒物浓度水平和粒径分布特征,并通过化学质量平衡(CMB)受体模型对颗粒物进行源解析。监测结果显示,夏季宁波、温州地区TSP和PM10日均浓度为0.049～0.134mg/m3和0.025～0.084mg/m3,均未超过我国环境空气质量二级标准;PM2.5日均浓度为0.007～0.069mg/m3,按美国2006年EPA最新标准限值0.035mg/m3衡量,奉化、乐清、北仑站的超标天数占总监测天数的比例分别为75%、40%和37.5%。粒径分布统计结果显示,3个监测站点PM10占TSP的比例为48.78%～86.96%;PM2.5占TSP的比例为33.33%～72.46%;奉化和乐清监测点PM10中PM2.5和PM1.0的比例平均值在50%以上。源解析结果显示,夏季TSP主要来源于土壤尘,其次是建筑尘和煤烟尘,其贡献率分别为40.70%～55.49%、9.62%～13.64%和5.85%～17.28%。     

2019—2021年徐州市大气细颗粒物化学组成特征及来源解析

徐州市地处四省交界，大气污染物来源复杂，颗粒物污染在气象条件不利时较为显著。通过地面观测数据、颗粒物组分连续观测、源解析及轨迹溯源等方法，对徐州市2019—2021年颗粒物变化特征进行了全面分析，以定量解析各类污染源的贡献，识别对颗粒物贡献显著的化学成分。结果表明：PM_2.5各组分质量占比中二次无机盐和有机碳相对较高，其中二次无机盐SNA(SO■、NO^-₃、NH⁺₄)占比达到59.1%～62.7%;水溶性离子总浓度逐年降低，但Mg²⁺和Ca²⁺浓度2021年分别同比增加2%和12.5%,说明扬尘污染存在反弹。秋冬季水溶性离子明显较高，Cl^-浓度明显高于其他季节，表明徐州市秋冬季受移动源、燃煤源和二次有机气溶胶共同影响。PM_2.5中OC与EC质量浓度比为4.88～8.40,说明徐州市颗粒物受多源影响，柴油、汽油机动车尾气排放以及燃煤排放对颗粒物贡献较大。后向轨迹分析表明，污染严重的1月污染物主...     

燃煤锅炉湿法脱硫烟气中颗粒物排放特征

选择北京市典型燃煤锅炉进行研究,结果表明:烟气中可凝结颗粒物在总颗粒物中占有较高比例,供热燃煤锅炉总颗粒物排放水平明显高于电厂燃煤锅炉;颗粒物中水溶性离子含量较高,供热燃煤锅炉硫酸根比例尤其显著;烟气总颗粒物中存在大量不稳定的易被氧化的组分;同为燃煤源,不同的烟气净化工艺排放的PM2.5组分特征差异明显;现有标准和技术规范存在不足,无法满足全面、准确监测污染源排放总颗粒物的实际需要。建议建立总颗粒物、可凝结颗粒物的监测技术规范,全面测算燃煤锅炉硫、氮化合物排放情况,科学评估脱硫及脱硝效率。     

Aerosol size distributions in urban Jinan: Seasonal characteristics and variations between weekdays and weekends in a heavily polluted atmosphere

Aerosol size distributions, trace gas, and PM(2.5) concentrations have been measured in urban Jinan, China, over 6 months in 2007 and 2008, covering spring, summer, fall, and winter time periods. Number concentrations of particles (10-2,500 nm) were 16,200, 13,900, 11,200, and 21,600 cm(?-3) in spring, summer, fall, and winter, respectively. Compared with other urban studies, Jinan has higher number concentrations of accumulation-mode particles (100-500 nm) and particles (10-2,500 nm), but lower concentrations of ultrafine particles (10-100 nm). The number, surface and volume concentrations, and size distributions of particles showed obvious seasonal variation and are also influenced by traffic emissions. Through correlation analysis, traffic emissions are proposed to be a more important contributor to Atkien-mode and accumulation-mode particles than coal firing. Around midday, the presence of nanoparticles and new particle formation is limited to pre-existing particles from traffic emissions and the mass transport of particles from suburban and rural areas. Compared with other studies in urban areas of Europe and the USA, the variation of particle number concentration and related gas concentration in Jinan between weekdays and weekends is smaller and the reasons has been deduced.     

Characterization of airborne trace metal and trace organic species from coal gasification

Fugitive emissions from a slagging fixed-bed coal-gasification pilot plant were analyzed by flameless atomic absorption spectrophotometry, gas chromatography, and mass spectrometry for trace metal and trace organic species. Analysis of the size distributions of airborne particulate matter inside the plant showed an abundance of large metal-containing particles; outdoor distributions in the vicinity of the plant resembled the indoor distributions, suggesting the importance of the gasifier in influencing ambient air quality. This conclusion was further supported by identification of similar organic compounds inside and outside the plant. Trace element enrichment factors based on the earth's crustal composition were greater than those based on the composition of the lignite used in the gasifier, showing the importance of characterizing the proper source material when inverstigating chemical fraction during aerosol formation. Enrichments in the present study were much greater than those found in previous sampling during aborted start-up and cleaning procedures, where normal operating temperatures had not yet been reached. Both studies showed evidence of enrichment factors which decreased with increasing particle size. Although much of the airborne mass was associated with large particles having low respirability, the high concentrations of some metals indoors suggests that further assessment of potential occupational exposures is warranted.     

燃煤电厂周边大气重金属污染特征及来源解析

为探究燃煤电厂周边大气环境中重金属的污染特征与来源,对广东某山区燃煤电厂周边地区环境和污染源的重金属进行测定,分析其污染特征,采用因子分析法和Pb同位素示踪法对环境中的重金属进行来源解析。结果表明,研究区域室内积尘中重金属浓度水平明显高于土壤重金属,污染空间分布与当地气象条件相关。环境空气TSP中重金属主要来自2个污染源,Cd、Pb、As主要来自电厂燃煤,Ca、Mn、Al、Mg主要来自土壤扬尘。TSP、降尘、积尘样品所含的Pb均与电厂采集的煤、炉渣、粉煤灰样品所含的Pb具有同源性,与其他污染源同源性不明显,说明研究区域大气中Pb污染主要来自电厂燃烧所排放的烟尘,其他污染源影响不大。     

Fossil-fueled power plants as a source of atmospheric carbon monoxide

Elevated carbon monoxide (CO) mixing ratios in excess of those derived from emissions inventories have been observed in plumes from one gas- and coal-fired power plant and three of four lignite coal-fired electric utility power plants observed in east and central Texas. Observations of elevated CO on days characterized by differing wind directions show that CO emissions from the lignite plants were relatively constant over time and cannot be ascribed to separate sources adjacent to the power plants. These three plants were found to be emitting CO at rates 22 to 34 times those tabulated in State and Federal emissions inventories. Elevated CO emissions from the gas- and coal-fired plant were highly variable on time scales of hours to days, in one case changing by a factor of 8 within an hour. Three other fossil-fueled power plants, including one lignite-fired plant observed during this study, did not emit substantial amounts of CO, suggesting that a combination of plant operating conditions and the use of lignite coal may contribute to the enhanced emissions. Observed elevated CO emissions from the three lignite plants, if representative of average operating conditions, represent an additional 30% of the annual total CO emissions from point sources for the state of Texas.     

Ambient Aerosol and its Carbon Content in Gainesville, a Mid-Scale City in Florida

Ambient aerosols were collected during 2000–2001 in Gainesville, Florida, using a micro-orifice uniform deposit impactor (MOUDI) to study mass size distribution and carbon composition. A bimodal mass distribution was found in every sample with major peaks for aerosols ranging from 0.32 to 0.56 μm, and 3.2 to 5.6 μm in diameter. The two distributions represent the fine mode (<2.5 μm) and the coarse mode (>2.5 μm) of particle size. Averaged over all sites and seasons, coarse particles consisted of 15% carbon while fine particles consisted of 22% carbon. Considerable variation was noted between winter and summer seasons. Smoke from fireplaces in winter appeared to be an important factor for the carbon, especially the elemental carbon contribution. In summer, organic carbon was more abundant. The maximum secondary organic carbon was also found in this season (7.0 μg m⁻³), and the concentration is between those observed in urban areas (15–20 μg m⁻³) and in rural areas (4–5 μg m⁻³). However, unlike in large cities where photochemical activity of anthropogenic emissions are determinants of carbon composition, biogenic sources were likely the key factor in Gainesville. Other critical factors that affect the distribution, shape and concentration were precipitation, brushfire and wind.     

Comparison of wood-dust aerosol size-distributions collected by air samplers

A method has been described previously for determining particle size distributions in the inhalable size range collected by personal samplers for wood dust. In this method, the particles collected by a sampler are removed, suspended, and re-deposited on a mixed cellulose-ester filter, and examined by optical microscopy to determine particle aerodynamic diameters. This method is particularly appropriate to wood-dust particles which are generally large and close to rectangular prisms in shape. The method was used to investigate the differences in total mass found previously in studies of side-by-side sample collection with different sampler types. Over 200 wood-dust samples were collected in three different wood-products industries, using the traditional 37 mm closed-face polystyrene/acrylonitrile cassette (CFC), the Institute of Occupational Medicine (IOM) inhalable sampler, and the Button sampler developed by the University of Cincinnati. Total mass concentration results from the samplers were found to be in approximately the same ratio as those from traditional long-term gravimetric samples, but about an order of magnitude higher. Investigation of the size distributions revealed several differences between the samplers. The wood dust particulate mass appears to be concentrated in the range 10-70 aerodynamic equivalent diameter (AED), but with a substantial mass contribution from particles larger than 100 microm AED in a significant number of samples. These ultra-large particles were found in 65% of the IOM samples, 42% of the CFC samples and 32% of the Button samples. Where present, particles of this size range dominated the total mass collected, contributing an average 53% (range 10-95%). However, significant differences were still found after removal of the ultra-large particles. In general, the IOM and CFC samplers appeared to operate in accordance with previous laboratory studies, such that they both collected similar quantities of particles at the smaller diameters, up to about 30-40 [micro sign]m AED, after which the CFC collection efficiency was reduced dramatically compared to the IOM. The Button sampler collected significantly less than the IOM at particle sizes between 10.1 and 50 microm AED. The collection efficiency of the Button sampler was significantly different from that of the CFC for particle sizes between 10.1 and 40 microm AED, and the total mass concentration given by the Button sampler was significantly less than that given by the CFC, even in the absence of ultra-large particles. The results are consistent with some relevant laboratory studies.     

不同气团来源对广州细颗粒物理化特性的影响

利用2006年7月广州细颗粒物质量浓度、数谱分布与化学组成的观测数据与气团后向轨迹聚类分析结果,系统分析了不同气团来源对广州细颗粒物理化特性的影响。观测期间,广州气团来源可分成来自远海、近海、西面陆地和北面陆地4种类型。细颗粒物总数浓度水平在4种类型中基本相当。当气团来自远海时,二次转化影响较小,PM2.5质量浓度较低,颗粒物数浓度从大到小依次为老化爱根核模态新鲜爱根核模态度积聚模态;受到海洋气团的影响,Cl-在PM2.5中比例为4种类型中最大。气团来自近海时,颗粒物二次生成与老化现象突出,数谱峰值出现在积聚模态,而其他类型出现在爱根核模态;SO2-4、OC与NO-3之和在PM2.5中的比例大于50%,为4种类型中最高。气团来自西面陆地和北面陆地时,细颗粒物受陆地传输老化气团和本地来源影响均较明显。来自北面陆地时,250 nm以上颗粒物数浓度明显升高,是PM2.5平均浓度远高于其他类型的直接原因之一。