一种新型微生物絮凝剂的制备及对Cu2+去除性能的探究

以城市污水处理厂的脱水污泥为原料,通过超声波细胞破碎制备微生物絮凝剂。采用控制变量法考察污泥浓度、超声波破碎时间对絮凝剂絮凝效果的影响,并探究絮凝液的投加量、pH值、温度、振荡时间、振荡频率、共存金属等因素对5 mg/L Cu^2+模拟废水的去除效果,分析了微生物絮凝剂去除Cu^2+的作用机理。结果表明:当污泥质量浓度为100 g/L,超声波破碎时间15 min时,絮凝剂的絮凝效果最好;当pH值为6.5,温度50℃,絮凝液投加量40 mL,振荡时间1 min,振荡频率200 r/min时去除效果最佳。     

对固体废物中挥发性有机物浸出方法的几点实验探讨

采用零顶空提取器,对陈旧油墨渣和蒽琨渣样品中的挥发性有机物进行了浸出实验和分析测定,浸出液采用静态顶空分流进样、GC/MS法分析。对影响挥发性有机物浸出效率的因素进行了研究,结果表明,浸提剂加入方式、浸出时间和浸出液收集方法等对分析结果准确度有较大影响。     

固体废物中重金属浸出试验方法的研究

在大量试验的基础上，提出了利用翻转式振荡机代替原有水平式振荡机对工业固体废物进行浸出毒性试验，并对翻转式浸取固体废物中重金属铜、锌、铬和镍的最佳浸出方法进行了研究。提出了翻转式浸取的最佳浸出方法。     

浸出毒性试验方法的研究

浸出毒性的法规定义是,一种固体废物的代表性样品,用规定的浸出程序和测试方法,测定浸出液中污染物的浓度等于或超过国家规定的污染控制标准,这种固体废物即具有浸出毒性.固体废物一般指固态、废液和多相废物.浸出毒性的监测项目不断增加,尤以有     

危险废物浸出毒性试验方法的研究

在分析各国危险废物浸出毒性试验方法的基础上,综合考虑我国气候状况(降雨量、酸雨现状)及工业固体废物处理处置现状,提出我国危险废物浸出毒性研究的技术路线为:通过模拟工业固体废物填埋场在不规范填埋处置且受酸雨影响条件下,有毒物质浸出向地下渗滤造成对地下水的污染,确定浸出毒性的浸取方法.浸出毒性保护目标为地下水,同时还介绍了主要技术参数液固比、浸取剂pH值和类型的确定方法.     

含氰废物浸出液监测分析方法探讨

通过对含氰固体废物浸出液分析化验的方法,来探讨取样、浸出液的及时制备、样品的不同振荡时间等几个问题。     

西南某省14种尾矿重金属浸出量及总量分析

研究中国西南某省不同类型尾矿的重金属浸出量及总量,为尾矿的污染防范、环境管理和综合利用提供参考和建议。采集了14种类型共164个有代表性尾矿进行浸出毒性试验,并分析其中79个典型尾矿样品的9种重金属含量,以评估其污染风险和综合利用价值。结果表明,有5种类型共7个样品出现浸出毒性超标,分别为铅锌矿、镍矿、银矿、铁矿、锰矿,总体超标率为4.3%。超标元素分别为砷、镉、锌、铅、铜、镍等6种元素,最大超标倍数分别为砷18.3倍、锌4.8倍、镉3.0倍、铅0.56倍、铜0.32倍、镍0.16倍;尾矿含有较多重金属,其中砷、锌、铅、铜含量较高,最高分别达到11.75%、2.60%、1.01%、0.29%,不同类型尾矿其重金属含量各有不同,铅锌矿尾矿的重金属总量最高。总体上,该省绝大多数尾矿为普通固废,少部分为危险废物,砷、镉、锌、铅、铜、镍等6种元素存在污染风险,其中砷元素是最主要污染物;尾矿由于重金属含量较高而有一定的综合利用价值。     

电镀废水中重金属的回收处理技术

电镀企业产生的漂洗水中含有大量的重金属,处理后生成的电镀重金属污泥属于危废,国家有相关的处置规定,若处置不当,会对环境造成二次污染,并且造成重金属的流失。介绍了利用离子交换法、电解法、膜分离技术、电去离子法等相关方法回收电镀漂洗废水中重金属的国内外的研究进展;从源头抓起,减少了电镀企业重金属元素的排放量,同时对废水的合理回用提供一些可行性方案。     

超声提取-电感耦合等离子体质谱法分析土壤中重金属化学形态

采用超声提取处理土壤样品,用ICP-MS分析样品中Cu、Zn、Pb、Cd、Ni、Cr等6种重金属元素形态,通过试验分析超声提取时土壤样品粒径、超声提取时间对提取效率的影响。方法在0.500μg/L~100μg/L之间线性良好,检出限为0.007μg/L~0.8μg/L,实际样品测定结果的RSD为4.7%~22.7%。土壤中重金属4种形态之和的总量与全量的相对偏差为11.0%~36.4%。将该方法与连续振荡法的试验结果比对,表明两方法对土壤样品的提取效率无显著性差异。     

铬渣制砖的毒性浸出及评价

对铬渣制砖的毒性浸出进行了研究，结果表明铬渣制砖可对六价铬起到封闭作用，但被封闭的六价铬的液体环境中会有浸出，砖样浸出液中六价铬的含量随时间及浸出方法的不同而不同，浸泡20d浸出液中六价铬含量达到稳定，碱性环境有利于六价铬的重新溶出。     

Design of a Leaching Test Framework for Coal Fly Ash Accounting for Environmental Conditions

Fly ash from coal combustion contains trace elements which, on disposal or utilisation, may leach out, and therefore be a potential environmental hazard. Environmental conditions have a great impact on the mobility of fly ash constituents as well as the physical and chemical properties of the fly ash. Existing standard leaching methods have been shown to be inadequate by not representing possible disposal or utilisation scenarios. These tests are often criticised on the grounds that the results estimated are not reliable as they are not able to be extrapolated to the application scenario. In order to simulate leaching behaviour of fly ash in different environmental conditions and to reduce deviation between measurements in the fields and the laboratories, it is vital to study sensitivity of the fly ash constituents of interest to major factors controlling leachability. pH, liquid-to-solid ratio, leaching time, leachant type and redox potential are parameters affecting stability of elements in the fly ash. Sensitivity of trace elements to pH and liquid to solid ratio (as two major overriding factors) has been examined. Elements have been classified on the basis of their leaching behaviour under different conditions. Results from this study have been used to identify leaching mechanisms. Also the fly ash has been examined under different standard batch leaching tests in order to evaluate and to compare these tests. A Leaching Test Framework has been devised for assessing the stability of trace elements from fly ashes in different environments. This Framework assists in designing more realistic batch leaching tests appropriate to field conditions and can support the development of regulations and protocols for the management and disposal of coal combustion by-products or other solid wastes of environmental concern.     

固体废物浸出液中氰化物测定方法的探讨

用金矿废渣样品进行氰化物的浸提试验，对浸提剂的pH值、浸提次数等条件进行优化。经实际样品验证，确定pH值〉12的碱性水溶液为最佳浸提剂，浸出液中易释放氰化物和总氰化物可用硝酸银滴定法或异烟酸一巴比妥酸分光光度法测定，方法检出限分别为0．25mg／L、0．001mg／L，加标回收率为90．0％～92．0％，测定结果的RSD〈8％。     

ICP－AES光谱法同时测定团体废物浸出液中的多种金属元素

采用翻转振荡方式以水为浸提剂浸提钢渣、尾矿渣、铬渣、铅渣、粉煤灰和电镀污泥试样，过滤后的浸提液经ＤＤＴＣ／ＣＣｌ４体系萃取富集后，用ＩＣＰ－ＡＥＳ法同时测定了Ｃｕ、Ｐｂ、Ｚｎ、Ｃｄ、Ｎｉ、Ｆｅ、Ｍｎ、Ｃｏ和Ｖ等多种金属元素．方法具有较好的精密度和准确度，宜于推广应用。     

Accelerated fractionation of heavy metals in contaminated soils and sediments using rotating coiled columns

A new approach to performing an accelerated sequential extraction of trace elements from solid samples has been proposed. It has been shown that rotating coiled columns (RCC) earlier used in counter-current chromatography can be successfully applied to the dynamic leaching of heavy metals from soils and sediments. A solid sample was retained in the rotating column as the stationary phase under the action of centrifugal forces while different eluents (aqueous solutions of complexing reagents, mineral salts and acids) were continuously pumped through. The procedure developed is time saving and requires only 4-5 h instead of the several days needed for traditional sequential extraction (TSE), complete automation being possible. Losses of solid sample are minimal. In most cases the recoveries of readily bioavailable and leachable forms of Pb, Zn, and Cd are higher, if a dynamic extraction in RCC is used. Since naturally occurring processes are always dynamic, continuous extraction in RCC may help to estimate the contents of leachable forms and their potential risk for the environment more correctly than batch TSE. The Kersten-Foerstner and McLaren-Crawford leaching schemes have been compared, the former has been found to be preferable.     

Study on the law of heavy metal leaching in municipal solid waste landfill

Comparative leaching experiments were carried out using leaching medium with different pH to municipal solid waste in the landfill columns in order to investigate the mobility of heavy metals. The leachate pH and oxidation–reduction potential were measured by oxidation–reduction potential analyzer; the contents of heavy metals were measured by inductively coupled plasma mass spectrometry. It is very different in leaching concentrations of heavy metals; the dynamic leaching of heavy metals decreased with the rise of the leaching amount on the whole. Acid leaching medium had definite influence on the leaching of heavy metals in the early landfill, but it had the obvious inhibition effect on the leaching in the middle and late period of landfill; the neutral and alkaline leaching medium are more beneficial to the leaching of heavy metals. Due to the influence of the environment of landfill, the differences of the results in cumulative leaching amount, leaching rate, and leaching intensity of heavy metals are very big. The calculation results of the release rates of heavy metals prove that the orders of the release rates are not identical under different leaching conditions. Acid rain made heavy metals migrate from municipal solid waste to soil and detain in soil more easily; approached neutral and alkaline leaching mediums are more beneficial to leaching of heavy metals in the municipal solid waste and soil with leachate. The field verification of experimental data showed that the law of heavy metal leaching in municipal solid waste revealed by the experiment has a good consistency with the data obtained by municipal solid waste landfill.     

我国固体废物监测中存在的问题及解决办法

本文针对我国废弃物监测中在采样、制样、浸出毒性实验、分析方法及标准制定方面存在的主要问题，进行了深入的探讨与研究，并提出了相应的解决办法和建议。     

Serial batch leaching procedure for characterization of coal fly ash

Although many leaching methods have been used for various purposes by research groups, industries, and regulators, there is still a need for a simple but comprehensive approach to leaching coal utilization by-products and other granular materials in order to estimate potential release of heavy metals when these materials are exposed to natural fluids. A serial batch characterization method has been developed at the National Energy Technology Laboratory that can be completed in 2–3 days to serve as a screening tool. The procedure provides an estimate of cumulative metals release under varying pH conditions, and leaching the sample at increasing liquid/solid ratios can indicate the rate at which this process will occur. This method was applied to eight fly ashes, adapted to the acidic or alkaline nature of the ash. The leachates were analyzed for 30 elements. The test was run in quadruplicate, and the relative standard deviation (RSD) was used as a measure of method reproducibility. RSD values are between 0.02 and 0.70, with the majority of the RSD values less than 0.3. The serial batch leaching procedure was developed as a simple, relatively quick, yet comprehensive method of estimating the risk of heavy metal release from fly ash when it is exposed to natural fluids, such as acid rain or groundwater. Tests on a random selection of coal fly ashes have shown it to be a reasonably precise method for estimating the availability and long-term release of cations from fly ash.     

Copper leaching from brake wear debris in standard extraction solutions

Quantification of the copper content of and copper leaching from a disc brake wear debris sample was performed using microwave-assisted acid digestion, the Federal Toxicity Characteristic Leaching Procedure (TCLP), and the State of California Waste Extraction Test (WET). The brake wear debris tested was a composite sample obtained from a brake dynamometer test of one brake pad source material. Comparative digestion studies demonstrated that a modified aqua regia matrix (HNO3:HCl:H2O2 = 1:3:0.5) optimized the digestion effectiveness for determining the total copper content in the brake wear debris. No significant sample heterogeneity within the brake wear debris was observed, based on statistically indistinguishable total copper content results for subsamples with a wide range of sample masses. Upon pooling all subsample results, an overall total copper content for the composite brake wear debris sample was determined to be 10.8% (g/g), with a 95% confidence limit of +/- 0.5% (g/g). Copper leaching increased with decreasing solid-to-liquid ratios in TCLP tests, but was unaffected by the solid-to-liquid ratio in the WET. For a 1:10(4) (g/g) solid-to-liquid ratio, 85% and 99% of the total mass of copper present in the composite brake wear debris sample was leached into solution during the TCLP and WET, respectively. Rate studies also demonstrated that the WET resulted in a faster rate and higher extent of copper leaching relative to the TCLP. Compared to reference copper-containing materials, the composite brake wear debris sample exhibited relatively higher TCLP and WET copper leaching characteristics. The higher copper leaching exhibited by the brake wear debris sample may have resulted from its higher specific surface area and/or from changes in the chemical form of copper that occurred during the braking process.     

饮用水源中痕量联苯胺的检测方法

建立了固相萃取高效液相色谱水中联苯胺的检测方法。选择Waters HLB固相萃取小柱富集水样,二氯甲烷/丙酮洗脱,以甲醇-水(pH=8,0.02 mol/L磷酸盐缓冲体系)作为流动相,保留时间为3.850 min,检测波长285 nm,0.1～10.0 mg/L范围内线性关系好,相关系数为0.999,检出限达到8×10-6mg/L,相对标准偏差为4.0%～9.5%,不同浓度样品加标回收率为80.5%～102.5%。