Solid phase extraction of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions with 1-(2-thiazolylazo)-2-naphthol loaded Amberlite XAD-1180

A new method for separation and preconcentration of trace amounts of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions in various matrices was proposed. The method is based on the adsorption and chelation of the metal ions on a column containing Amberlite XAD-1180 resin impregnated with 1-(2-thiazolylazo)-2-naphthol (TAN) reagent prior to their determination by flame atomic absorption spectrometry (FAAS). The effect of pH, type, concentration and volume of eluent, sample volume, flow rates of sample and elution solutions, and interfering ions have been investigated. The optimum pH for simultaneous retention of all the metal ions was 9. Eluent for quantitative elution was 20 ml of 2 mol l(-1) HNO(3). The optimum sample and eluent flow rates were found as 4 ml min(-1), and also sample volume was 500 ml, except for Mn (87% recovery). The sorption capacity of the resin was found to be 0.77, 0.41, 0.57, and 0.30 mg g(-1) for Cu(II), Ni(II), Cd(II), and Mn(II), respectively. The preconcentration factor of the method was 200 for Cu(II), 150 for Pb(II), 100 for Cd(II) and Ni(II), and 50 for Mn(II). The recovery values for all of the metal ions were > or = 95% and relative standard deviations (RSDs) were < or = 5.1%. The detection limit values were in the range of 0.03 and 1.19 microg l(-1). The accuracy of the method was confirmed by analysing the certified reference materials (TMDA 54.4 fortified lake water and GBW 07605 tea samples) and the recovery studies. This procedure was applied to the determination of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) in waste water and lake water samples.     

Impact of wastewater treatment plant discharge of lidocaine, tramadol, venlafaxine and their metabolites on the quality of surface waters and groundwater

The presence of the anesthetic lidocaine (LDC), the analgesic tramadol (TRA), the antidepressant venlafaxine (VEN) and the metabolites O-desmethyltramadol (ODT) and O-desmethylvenlafaxine (ODV) was investigated in wastewater treatment plant (WWTP) effluents, in surface waters and in groundwater. The analytes were detected in all effluent samples and in only 64% of the surface water samples. The mean concentrations of the analytes in effluent samples from WWTPs with wastewater from only households and hospitals were 107 (LDC), 757 (TRA), 122 (ODT), 160 (VEN) and 637 ng L(-1) (ODV), while the mean concentrations in effluents from WWTPs treating additionally wastewater from pharmaceutical industries as indirect dischargers were for some pharmaceuticals clearly higher. WWTP effluents were identified as important sources of the analyzed pharmaceuticals and their metabolites in surface waters. The concentrations of the compounds found in surface waters ranged from 相似文献   

Iodide-assisted total lead measurement and determination of different lead fractions in drinking water samples

Lead and its compounds are toxic and can harm human health, especially the intelligence development in children. Accurate measurement of total lead present in drinking water is crucial in determining the extent of lead contamination and human exposure due to drinking water consumption. The USEPA method for total lead measurement (no. 200.8) is often used to analyze lead levels in drinking water. However, in the presence of high concentration of the tetravalent lead corrosion product PbO(2), the USEPA method was not able to fully recover particulate lead due to incomplete dissolution of PbO(2) particles during strong acid digestion. In this study, a new procedure that integrates membrane separation, iodometric PbO(2) measurement, strong acid digestion and ICP-MS measurement was proposed and evaluated for accurate total lead measurement and quantification of different lead fractions including soluble Pb(2+), particulate Pb(II) carbonate and PbO(2) in drinking water samples. The proposed procedure was evaluated using drinking water reconstituted with spiked Pb(2+), spiked particulate Pb(II) carbonate and in situ formed or spiked PbO(2). Recovery tests showed that the proposed procedure and the USEPA method can achieve 93-112% and 86-103% recoveries respectively for samples containing low PbO(2) concentrations (0.018-0.076 mg Pb per L). For samples containing higher concentrations of PbO(2) (0.089-1.316 mg Pb per L), the USEPA method failed to meet the recovery requirement for total lead (85-115%) while the proposed method can achieve satisfactory recoveries (91-111%) and differentiate the soluble Pb(2+), particulate Pb(II) carbonate and PbO(2).     

The effect of the presence of trace metals on the oxidation of Sb(III) by hydrogen peroxide in aqueous solution

Despite its importance for understanding the behaviour of antimony in the environment, the oxidation kinetics of Sb(III) with natural oxidants is still not well understood. We have studied the oxidation of Sb(III) by hydrogen peroxide on a time scale of hours in the presence of some trace metals, Cu(II), Mn(II), Zn(II) and Pb(II), under pH and concentration conditions close to natural ones. The effects that these trace metals have on Sb(iii) oxidation by hydrogen peroxide vary. Zn(II) had no catalytic effect at all, but Cu(II), Mn(II) and Pb(II) did, though their effects were not uniform. Cu(II) significantly accelerated the reaction, which remained first-order with respect to Sb(III) at any Cu(II) concentration tested. Pb(II) and Mn(II) also enhanced the reaction rates, but the apparent order of the reaction with respect to Sb(III) changed to two. The trace metal effect observed was concentration dependent for Pb(II). The addition of the hydroxyl radical scavenger 2-propanol suggests that the trace metal catalytic effect observed involves the action of hydroxyl radicals, but that they are not responsible for the oxidation of Sb(III) by H2O2 in the absence of trace metals. The fact that Sb(III) can be oxidized by hydroxyl radicals present in water, even if it is not capable of producing them, has important environmental implications because hydroxyl radicals are known to be abundant in many natural waters such as seawater, humic-rich surface waters or rainwater.     

Techniques and methods for the determination of haloacetic acids in potable water

Haloethanoic (haloacetic) acids (HAAs) are formed as disinfection byproducts (DBPs) during the chlorination of natural water to make it fit for consumption. Sundry analytical techniques have been applied in order to determine the concentrations of the HAAs in potable water supplies: gas chromatography (GC-MS, GC-ECD); capillary electrophoresis (CE); liquid chromatography (LC), including ion chromatography (IC); and electrospray ionization mass spectrometry (ESI-MS). Detection limits required to analyze potable water samples can be regularly achieved only by GC-ECD and ESI-MS. Without improvements in preconcentration or detector sensitivity, CE and LC will not find application to potable water supplies. The predominant GC-ECD methods use either diazomethane or acidified methanol to esterify (methylate) the carboxylic acid moiety. For HAA5 analytes, regulated under the EPA's Stage 1 DBP Rule, diazomethane is satisfactory. For HAA9 data gathered under the Information Collection Rule, acidified methanol outperforms diazomethane, which suffers from photo-promoted side reactions, especially for the brominated trihaloacetic acids. Although ESI-MS can meet sensitivity and selectivity requirements, limited instrumentation availability means this technique will not be widely used for the time being. However, ESI-MS can provide valuable confirmatory information when coupled with GC-ECD in a research setting.     

Simplification and validation of a large volume polyurethane foam sampler for the analysis of persistent hydrophobic compounds in drinking water

The use of a large volume polyurethane foam (PUF) sampler was validated for rapid extraction of persistent organic pollutants (POPs), such as polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), in raw water and treated water from drinking water plants. To validate the recovery of target compounds in the sampling process, a (37)Cl-labeled standard was spiked into the 1st PUF plug prior to filtration. An accelerated solvent extraction method, as a pressurized liquid extractor (PLE), was optimized to extract the PUF plug. For sample preparation, tandem column chromatography (TCC) clean-up was used for rapid analysis. The recoveries of labeled compounds in the analytical method were 80-110% (n = 9). The optimized PUF-PLE-TCC method was applied in the analysis of raw water and treated potable water from seven drinking water plants in South Korea. The sample volume used was between 18 and 102 L for raw water at a flow rate of 0.4-2 L min(-1), 95 and 107 L for treated water at a flow rate of 1.5-2.2 L min(-1). Limit of quantitation (LOQ) was a function of sample volume and it decreased with increasing sample volume. The LOQ of PCDD/Fs in raw waters analyzed by this method was 3-11 times lower than that described using large-size disk-type solid phase extraction (SPE) method. The LOQ of PCDD/F congeners in raw water and treated water were 0.022-3.9 ng L(-1) and 0.018-0.74 ng L(-1), respectively. Octachlorinated dibenzo-p-dioxin (OCDD) was found in some raw water samples, while their concentrations were well below the tentative criterion set by the Japanese Environmental Ministry for drinking water. OCDD was below the LOQ in the treated drinking water.     

Characterization of humic-rich hydrocolloids and their metal species by means of competing ligand and metal exchange--an on-site approach

An improved on-site characterization of humic-rich hydrocolloids and their metal species in aquatic environments was the goal of the present approach. Both ligand exchange with extreme chelators (diethylenetetraaminepentaacetic acid (DTPA), ethylendiaminetetraacetic acid (EDTA)) and metal exchange with strongly competitive cations (Cu(II) were used on-site to characterize the conditional stability and availability of colloidal metal species in a humic-rich German bogwater lake (Venner Moor, Münsterland). A mobile time-controlled tangential-flow ultrafiltration technique (cut-off: 1 kDa) was applied to differentiate operationally between colloidal metal species and free metal ions, respectively. DOC (dissolved organic carbon) and metal determinations were carried out off-site using a home-built carbon analyzer and conventional ICP-OES (inductively-coupled plasma-optical emission spectrometry), respectively. From the metal exchange equilibria obtained on-site the kinetic and thermodynamic stability of the original metal species (Fe, Mn, Zn) could be characterized. Conditional exchange constants Kex obtained from aquatic metal species and competitive Cu(II) ions follow the order Mn > Zn > > Fe. Obviously, Mn and Zn bound to humic-rich hydrocolloids are very strongly competed by Cu(II) ions, in contrast to Fe which is scarcely exchangeable. The exchange of aquatic metal species (e.g. Fe) by DTPA/EDTA exhibited relatively slow kinetics but rather high metal availabilities, in contrast to their Cu(II) exchange.     

Chthamalus montagui as biomonitor of metal contamination in the northwest coast of Portugal

The concentrations of seven metals (Cd, Cr, Cu, Fe, Mn, Ni and Zn) were determined in coastal seawaters and soft and hard tissues of the barnacle Chthamalus montagui from the northwest coast of Portugal to assess the potential use of C. montagui as biomonitor of metal contamination. The results of this study showed that C. montagui soft tissues can be used for monitoring metal bioavailabilities in these coastal seawaters: (1) there were significant correlations (p?相似文献   

Groundwater quality assessment in the urban-west region of Zanzibar Island

This paper highlights the levels of anions (nitrate, nitrite, sulfate, bromide, chloride, and fluoride) and cations (potassium, sodium, magnesium, and calcium) in selected springs and groundwater sources in the urban-west region of Zanzibar Island. The levels of total dissolved solids (TDS) and sodium adsorption ratio (SAR) were also studied. Thirty water samples were collected in December 2012 from various types of water sources, which included closed hand-dug wells (CHDW), open hand-dug wells (OHDW), springwater (SW), public bore wells (PBW), and bore wells owned by private individuals (BWP), and analyzed after filtration and sometimes dilution. The cations were analyzed using inductively coupled plasma-optical emission spectrometry (ICP-OES). The anions were analyzed by chemically suppressed ion chromatography (IC). The ranges of the levels of the investigated parameters were as follows: Na 13.68–3,656 mg L^?1, K 2.66–583 mg L^?1, Mg 0.63–131.10 mg L^?1, Ca 16.79–189.9 mg L^?1, Cl^? 8.61–4,340.97 mg L^?1, F^? 0–1.02 mg L^?1, Br^? 0–10.88 mg L^?1, NO₃ ^? 0.18–342.4 mg L^?1, NO₂ ^? 0–1.39, SO₄ ^2? 4.43–534.02 mg L^?1, TDS 7–6,380 mg L^?1, and SAR 0.63–50. Except fluoride, most of the studied parameters in the water samples had concentrations beyond the permissible limits of the World Health Organization (WHO). The elevated concentrations are a result of seepage of contaminated water from on-site septic tanks, pit latrines, landfill leachates, fertilizer applications, and domestic effluents. These results should alert domestic water stakeholders in Zanzibar to the urgent task of initiating a quick mitigation response to control these alarming water risks.     

Determination of 226Ra at ultratrace level in mineral water samples by sector field inductively coupled plasma mass spectrometry

An analytical procedure has been proposed for the determination of (226)Ra at the low femtogram per ml concentration level in mineral water samples using double focusing sector field ICP-MS (ICP-SFMS). For the pre-concentration and separation of radium from the matrix elements in water a tandem of a laboratory-prepared filter, based on MnO(2), and Eichrom "Sr-specific" resin was used. The recovery of the method was determined to be 70.5%. The limit of detection for (226)Ra determination was 0.02 fg ml(-1), including a pre-concentration factor of 10. In addition, uranium concentration and uranium isotope ratios were measured by ICP-SFMS. In several mineral water samples with a relatively high uranium content, (226)Ra concentrations were found between 0.7-15 fg ml(-1). The effective dose of the contribution was calculated using the radionuclide concentration and dose conversion factors from the World Health Organization, WHO (1993). Assuming a mineral water consumption of 2 l d(-1), a slightly higher calculated dose than the suggested limit for drinking water (0.1 mSv y(-1)) was found in some samples.     

Characterisation of mineralogical forms of barium and trace heavy metal impurities in commercial barytes by EPMA, XRD and ICP-MS

This study was carried out to characterise the mineralogical forms of barium and the trace heavy metal impurities in commercial barytes of different origins using electron probe microanalysis (EPMA), X-ray diffraction (XRD) and inductively coupled plasma mass spectrometry (ICP-MS). Qualitative EPMA results show the presence of typically eight different minerals in commercial barytes including barite (BaSO4), barium feldspar, galena (PbS), pyrite (FeS2), sphalerite (ZnS), quartz (SiO2), and silicates, etc. Quantitative EPMA confirms that the barite crystals in the barytes contain some strontium and a little calcium, whereas trace heavy metals occur in the associated minerals. Analysis of aqua regia extracts of barytes samples by ICP-MS has shown the presence of a large number of elements in the associated minerals. Arsenic, copper and zinc concentrations correlate closely in all 10 samples. The findings suggest that barytes is not, as traditionally thought, an inert mineral, but is a potentially toxic substance due to its associated heavy metal impurities, which can be determined by an aqua regia digest without the need for complete dissolution of the barite itself. X-ray powder diffraction was not informative as the complex barite pattern masks the very weak lines from the small amounts of associated minerals.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Studies on heavy metals in the ground waters of the city of Aligarh U.P. (India)

A study was conducted to determine the levels of heavy metals Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn along with physico-chemical parameters in ground waters of Aligarh city, U.P. (India). Twenty seven samples of hand pump water and twenty three samples of municipal water supply were collected from different localities of the Aligarh city, five times during the period of two months at intervals of 12 days. The samples were analysed for physico-chemical characteristics (pH, electrical conductivity, chlorides, sulphates, total hardness, total alkalinity, nitrate-nitrogen, fluoride, calcium and magnesium) and heavy metal contents. The concentrations of heavy metals in the hand pump water samples were found in the ranges of Cd (ND-5.00); Cr (ND-30.00); Cu (ND-82.50); Fe (16.80–460.00); Mn (ND-425.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (28.60–775.00) g l^–1. The heavy metal concentrations in the municipal water supply samples were found to be Cd (ND-5.00); Cr (ND-25.00); Cu (ND-37.50); Fe (8.00–37.50); Mn (ND-320.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (2.00–271.87) g l^–1.It appears from the results of these studies the concentrations of Cd, Cr, Cu, Ni, Pb, and Zn in the ground waters of the Aligarh City were found to be lower than the prescribed limits of World Health Organisation (1984), whereas the values of Fe and Mn were found above the prescribed limits in some localities. The chloride total hardness and nitrate-nitrogen were comparatively higher in the hand pump water than the municipal supply water. The reason of higher values of these parameters may be ascribed to the surface disposal of sewage wastes, wastes from metal processing industries and other house hold refuses.     

The efficiency of Amberlite XAD-4 resin loaded with 1-(2-pyridylazo)-2-naphthol in preconcentration and separation of some toxic metal ions by flame atomic absorption spectrometry

A selective method has been developed for the determination of trace amount of metal ions after preconcentration on 1-(2-pyridylazo)-2-naphthol loaded Amberlite XAD-4 resin. The chelating resin was characterized on the basis of infra red spectra, thermal and chemical stability, and hydrogen ion capacity. High preconcentration factor of 160?C400 up to a low preconcentration limit of 10 ??g L^???1 has been achieved for almost all the metals. The chelating resin was highly selective even in the presence of large concentrations of alkali and alkaline earth metals and various matrix components. Chromatographic separation of metal ions in binary mixtures has been accomplished. The analytical utility of the resin for metal ions was explored by analyzing natural water and standard reference materials.     

Reduced Metals Concentrations of Water, Sediment and Hyalella Azteca from Lakes in the Vicinity of the Sudbury Metal Smelters, Ontario, Canada

Hyalella azteca (Crustacea: Amphipoda), water and sediments from 12 circum-neutral lakes between Sudbury and North Bay in Ontario, Canada were sampled in August 1998 and analyzed for 10 metals including Cu, Zn, Cd, Ni, Pb, Co, Mo, V, Ba and Ti. Statistical analyses showed that concentrations of the metals in H. azteca, water and sediment differed significantly (ANOVA, P<0.05) among lakes (except for Zn and Pb in H. azteca and Mo in water). There was a trend of declining metal concentration, especially for Cu, Ni and Co (in water, Hyalella and sediment), with distance from the smelters indicating the reduced impact of atmospheric pollution. Metal concentrations of lakes (water) in the Sudbury area were found to be lower compared to data from the 1970s and 1980s indicating an improvement in water quality. Metal concentrations in field-collected amphipods compared favorably with those measured in the laboratory in animals exposed to deep-water sediments, provided metal concentrations were not extremely low (e.g., Pb) and that water chemistry differences (e.g., pH) were taken into account for some metals (especially Cd). In general bioaccumulation of metals in H. azteca was predicted better from surface water than from sediment total metal.     

Water-soluble species and heavy metal contamination of the petroleum refinary area,Jordan

The levels of lead, cadmium, copper, zinc, aluminum, chromium, and iron in street dust, soil, and plants in the Jordanian petroleum refinery were determined using flame and graphite-furnace atomic absorption spectrophotometry. Major cations (Li+, Na+, NH4+, K+, Mg2+, and Ca2+) and anions (F-, Cl-, NO3-, SO4(2-), and Br-) were also determined using suppression mode ion chromatography. Generally, higher levels of the heavy metals studied were found in street dust samples than in soil samples. On the other hand, except Cl-, and Li+ ions, other anions and cations showed higher concentrations in soil than in street dust samples. For plant samples, unwashed samples showed higher levels of heavy metals than their washed counterparts, indicating that dust fall is a source of heavy metal contamination.     

Impacts of Debris-Flow Deposits on Hydrogeochemical Processes and the Development of Dryland Salinity in the Cross-River Catchment, SE, Nigeria

This research focuses on the effect of debris-flow on thevarious hydrogeochemical processes occurring at Cross-River as aresult of disposal of industrial and household wastes as well as sewage into the river. It also focuses on development anddetermination of the saline nature of the rivers dry land.The study is carried out by a survey at different depths of theriver for water and soil samples analysis.The results show that concentrations of cations and anionsreasonably high and uniform except for nitrates which is quitehigh due to agricultural activities occurring in the study areas.Also Mg and SO₄ ions are high due to reactions within thecolluvium include ion exchange of calcium for sodium in basalclays; dissolution of sodium chloride from dust – derived saltparticles in the clay-rich colluvium reactions.The Electrical conductive shows that Cross-River containsdissolved solids. Soil analysis indicates the presence of K, Ca,Mg, and Cl. pH values were also deducted from soil samples (6.30–6.45).     

Novel solid-phase extractor based on functionalization of multi-walled carbon nano tubes with 5-aminosalicylic acid for preconcentration of Pb(II) in water samples prior to determination by ICP-OES

New solid-phase extractor (MWCNTs-5-ASA) was synthesized via covalent immobilization of 5-aminsalicylic acid onto multi-walled carbon nanotubes (MWCNs). The success of the functionalization process was confirmed using Fourier transform infrared spectroscopy, scanning electron microscope, and surface coverage determination. Batch experiments were conducted as a function of pH to explore MWCNTs-5-ASA efficiency to extract several metal ions viz., Cr(III), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Pb(II). It was found that Pb(II) exhibits the highest extraction percentage with maximum adsorption capacity 32.75 mg g^?1. Its binding performance was well fitted with Langmuir sorption isotherm. On the other hand, the selective separation and preconcentration of trace Pb(II) under dynamic conditions prior to determination by inductively coupled plasma-optical emission spectrometry was investigated under different parameters. These included the rate of flow and volume of sample solution, in addition to the type of the eluate, its volume and concentration. The effect of a variety of foreign ions on the recovery percentage was also evaluated. Trace Pb(II) ions present in 500 mL aqueous solution adjusted to pH 4.0 were retained on 50 mg of MWCNTs-5-ASA and completely eluted using 4.0 mL of 2 M HNO₃. The limit of detection and the precision of the method were 0.25 ng mL^?1 and 2.8 %, respectively (N?=?5). This methodology has been applied for the determination of Pb(II) in water samples with good results.     

Heavy metal pattern and solute concentration in soils along the oldest highway of the world – the AVUS Autobahn

Highways and main roads are a potential source of contamination for the surrounding environment. High traffic rates result in elevated heavy metal concentrations in road runoff, soil and water seepage, which has attracted much attention in the recent past. Nonetheless, investigations of pollutants in roadside soils are still a subject of major interest due to the rapid development of traffic systems and increasing traffic all over the world. The accumulation of the heavy metals Pb, Cd, Cu and Zn in soils along the oldest federal highway of the world has been studied by sampling a roadside transect of 125 by 10?m. In addition, heavy metal concentrations of Pb, Cd, Zn, Cu, Ni and Cr in soil solutions from different distances (2.5, 5 and 10?m) from the hard shoulder of the highway and from three soil depths (10, 30, and 50?cm) were investigated. The results show that heavy metal concentrations are up to 20 times increased compared to the geochemical background levels and a reference site of 800-m distance from the roadside. Soil matrix concentrations in the topsoil (0-10?cm) mostly exceeded the precautionary values of the German Federal Soil Protection and Contamination Ordinance (BBodSchV). The concentrations of Cd, Pb and Zn in the soil matrix tended to decrease with distance from the roadside edge, whereas the concentrations in the soil solution increased at a distance of 10?m onwards due to a lower soil pH. Because of both high pH values and a high sorption capacity of the soils, soil solution concentrations seldom exceeded the trigger values of the German Federal Soil Protection and Contamination Ordinance (BBodSchV) for transferring soil solution to groundwater.     

Bioaccumulation of Metals in Fish of Salmonidae Family and the Impact on Fish Meat Quality

The study was aimed at determining the levels of metals in water samples and muscles of the fish caught in the Una River basin, located in the northwestern part of Bosnia and Herzegovina. For that purpose, three fish species: Brown Trout (Salmo trutta m. fario), Grayling (Thymallus thymallus) and Californian Trout (Salmo gairdneri), together with stem water samples, were analyzed for metal concentrations (Pb, Hg, Cd, As, Mn, Ni, Cu, Cr, Se, Co, Sn, Zn, Fe, Ca, P) during a 2-year period. The fish was captured using electric fishing, nets or fishing equipment. The capture was undertaken on three sites (the river source, the middle flow and the river mouth) of each of the five biggest rivers belonging to the Una River basin (Unac, Krušnica, Sana, Klokot, and Una). The concentrations of metals in each sample were determined via atomic absorption spectrophotometry. In the tested waters, the presence of Mn in concentrations higher than permitted (0.07 mg/l) had been detected. In the tested meat, the following average concentrations of metals (mg/kg) had been found: Pb (0.67), Cd (0.06), Mn (0.65), Ni (0.15), Cu (0.79), Cr (1.05), Se (0.03), Zn (8.92), Fe (5.40), Ca (14.68), and P (10.85). The correlation between Mn concentrations identified in the tested waters and those identified in the meat of Brown Trout was revealed to be statistically significant, which confirms that, over time, bioaccumulation of metals took place. Even though the results were not indicative of contamination, they strongly suggest that constant monitoring of the ecosystems in reference should be implemented.