水体表面微层中DBP和DEHP的色谱测定

建立了用气相色谱（ＧＣ）和反相高效液相色谱（ＲＰＨＰＬＣ）分析邻苯二甲酸二丁酯（ＤＢＰ）和邻苯二甲酸二异辛酯（ＤＥＨＰ）的方法。首次在ＨＰＬＣ中用异丙醇作为流动相分离上述两种化合物,取得满意的结果。ＧＣ的检测限为ＤＢＰ２ｎｇ,ＤＥＨＰ２ｎｇ。ＨＰＬＣ的检测限为ＤＢＰ５ｎｇ,ＤＥＨＰ１０ｎｇ。两种方法都有良好的精密度、回收率,并用这两种分析方法分析了湖水水体表面微层水样中的ＤＢＰ和ＤＥＨＰ     

半渗透膜采样技术监测城市污水处理流程中的难降解有毒有机污染物

应用新型半透膜采样技术（ＳＰＭＤ）,监测某城市污水处理流程中８个点污水中两类难降解有毒有机污染物多氯联苯（ＰＣＢ）和多环芳烃（ＰＡＨ）,同时同地采集水样,气相色谱质谱联机,选择性离子扫描方式对各ＰＣＢ异构体和ＰＡＨ定性定量。与水样液液萃取相比,ＳＰＭＤ采样技术显著提高了分析的准确度。根据测定的采样器中污染物浓度,推算采样期间该点污水中的平均浓度,与瞬间水样分析结果符合程度较好。半透膜采样方法可用于污水处理工艺流程中多氯联苯和多环芳烃污染物的定性和半定量监测     

大气和废气中邻苯二甲酸酯的监测方法

本文通过气相色谱法建立了大气中邻苯二甲酸酯的监测方法。对大气和废气中的邻苯二甲酸二丁酯（ＤＢＰ）和邻苯二甲酸二辛酯（ＤＯＰ）进行测定,从样品的采集到色谱条件的选择,进行了一系列实验方法探讨。该方法检出限大大低于ＤＢＰ、ＤＯＰ的环境目标值,结果令人满意。     

空气或废气中挥发性醛、酮的气相色谱法测定

本文研究采用了空气或废气中挥发性醛、酮类化合物在常温下经２，４二硝基苯肼（ＤＮＰＨ）的酸性饱和溶液吸收，分别形成各自的腙，用ＣＳ２萃取后，经气相色谱法（ＧＣＦＩＤ）以３％ＳＥ３０／ＣｈｒｏｍｏｓｏｒｂＷＨＰ８０１００目为固定相和载体，分离测定，对空气或废气中的甲醛、乙醛、丙烯醛、丁醛、丙酮、丁酮、甲基异丁基酮等的测定，获得较满意的结果。     

二溴羟基苯基荧光酮-OP胶束荧光熄灭法测定地面水中的微量铁(Ⅲ)

本文基于Ｆｅ（Ⅲ）二溴羟基苯基荧光酮（ＤＢＨ—ＰＦ）ＯＰ体系的荧光熄灭效应,提出一种测定微量铁（Ⅲ）的新荧光方法,在ｐＨ３８４８的缓冲介质范围内和ＯＰ存在下,Ｆｅ（Ⅲ）与ＤＢＨＰＦ形成１∶３的络合物,络合物的最大激发波长和发射波长分别是３６５ｎｍ和５６０ｎｍ。铁（Ⅲ）量在０１６～１８０μｇ／Ｌ范围内与△Ｆ成线性关系,检测限为０１６μｇ／Ｌ,方法用于地面水中微量铁的测定,结果满意。     

气相色谱法测定废水中N，N─二甲基甲酰胺

用气相色谱仪氢焰检测器，ＰＥＧ２０Ｍ毛细管柱测定废水中的Ｎ，Ｎ二甲基甲酰胺（ＤＭＦ），结果表明与分光光度法基本一致     

CL-5209微色谱柱分离富集光度法测定环境样品中微量铀

研究了ＣＬ５２０９萃淋树酯微色谱柱柱性能以及对铀和主要伴生元素的分离富集情况。结果表明,在１ｍｏｌ／Ｌ硝酸介质中,除铀（Ⅵ）、钍（Ⅳ）、金（Ⅲ）和少量稀土元素能被ＣＬ５２０９萃淋树酯吸附外,其它常见共存元素不被吸附。用５ｍｌ１ｍｏｌ／Ｌ的ＨＮＯ３可以安全淋洗除去钍和少量稀土,再用１４ｍｌ混合掩蔽剂可以完全解析铀,结合以在溴代十六烷基吡啶存在下５Ｂｒ－ＰＡＤＡＰ显色,能快速准确地测定环境样品中ｐｐｂ级铀     

钻井污水化学需氧量的研究

针对石油工业钻井污水高化学需氧量（ＣＯＤ）严重超标的状况,对钻井污水的化学需氧量进行研究。分折测定了８种钻井液添加剂（ＰＡＮ、ＰＡＭＩ、ＨＰＡＮ、柴油、磺化沥青、ＸＹ２７、ＣＭＣ、ＦＡ３６７）的ＣＯＤ;重点探讨了钻井液添加剂对钻井污水ＣＯＤ的影响,同时对钻井污水ＣＯＤ处理效果的影响进行了研究。实验结果表明,不同钻井液添加剂对钻井污水的ＣＯＤ的影响程度各不相同;钻井污水中ＣＯＤ值严重超标的主要因素是钻井液添加剂;并且钻井液添加剂浓度与其对应的ＣＯＤ之间存在良好的一元线性关系。根据一元线性回归方程可较好地预测油田现场各钻井液添加剂对ＣＯＤ的影响,为解决钻井污水处理这一难题提供科学依据。     

无平衡室条件下测定TSP质量控制问题的探讨

无平衡室条件下测定ＴＳＰ质量控制问题的探讨ＤｉｓｃｕｓｓｉｏｎｏｎＱｕａｌｉｔｙＣｏｎｔｒｏｌＰｒｏｂｌｅｍｓｏｆＴＳＰＤｅｔｅｒｍｉｎａｔｉｏｎＵｎｄｅｒｎｏＥｑｕｉｌｉｂｒｉｕｍＣｏｎｄｉｔｉｏｎ庄云霞（江苏省江都市环境监测站江都２２５２００）Ｔ...     

YSI-58型DO测量仪静态测DO的可行性

ＹＳＩ５８型ＤＯ测量仪静态测ＤＯ的可行性刘兴安（广东省佛山市环境监测站，佛山５２８０００）实验表明，静态测得的ＤＯ值与动态（搅拌）ＤＯ值误差达２１０～２３３ｍｇ／Ｌ，动态的ＤＯ值误差变化不稳定。结果证明，静态值代入（Ｘ÷Ｋ）＋Ｘ公式求ＤＯ值是可...     

螯合树脂在线富集——火焰原子吸收光度法测定水中微量Cu,Pb,Zn,Cd

对螯合树脂在线富集，火焰原子吸收光度法进行了条件试验。试验证实方法对Ｃｕ、Ｐｂ、Ｚｎ、Ｃｄ４个元素检出浓度可达μｇ／Ｌ级，校准曲线性、样品重现性及准确度可满足测定要求。     

Preservation of sulfidic waters containing dissolved As(III)

Solutions containing variable concentrations of sulfide (0 to 31 ppm) and arsenite (0.35 to 10 ppm) were subjected to several different preservation treatments. As predicted by equilibrium thermodynamics, at near-neutral pH the experimental solutions were undersaturated with respect to orpiment (As2S3). However, upon acidification to pH 2 with HCl or HNO3, instantaneous precipitation of poorly crystalline As2S3 occurred in sulfidic solutions which resulted in the loss of dissolved arsenite. These results have implications concerning the practice of acidifying water samples containing hydrogen sulfide with HCl or HNO3 for the purpose of preserving total arsenic values. If a near-neutral water sample contains 1 ppm arsenite and as little as 0.4 ppm sulfide, loss of dissolved arsenic will occur upon acidification. An alternative three-step preservation method involving base addition, oxidation, and acidification is proposed and investigated as an appropriate technique for preserving sulfide-bearing aqueous samples for total arsenic.     

Analysis of volatile organic compounds (VOCs) in sediments using in situ SPME sampling

A new method of determining the composition of sediment/soil gases and their volatile organic compound (VOC) content is described. VOCs were collected in situ from intertidal sediments in the Menai Strait and surrounding areas. The sampling was performed using a portable sampler comprising a funnel coupled to a SPME fibre. Gases were extracted from the sediments using a small vacuum pump pulling 100 mL min(-1) at atmospheric pressure. Sixty one different compounds were detected in the samples, and their fluxes and concentrations were determined. The compounds were classified into groups: halogenated, sulfur containing compounds, aldehydes, BTEXs (benzene, toluene, ethyl benzene and xylene) and aliphatic hydrocarbons. Results of principal component analysis (PCA) showed that the chemical composition of extracted gas was influenced primarily by sediment type. Muddy anoxic sediments were dominated by halogenated and sulfur containing compounds and sandy sediments had more aldehydes and BTEXs.     

Water treatment control using the joint estimation outlier detection method

The loss of contaminated wastewater into the environment by leakage or other means is a serious problem. This problem is essentially the same as true of the loss of chemical reagents from a chemical production or purification process. The present article shows how the joint estimation method, an outlier detection method for time series analysis, can be used by a facility manager to deal with these problems.     

关于区域环境质量的复合模糊距离评价方法及应用探讨

从分析环境质量结构和模糊理论对环境质量构成特征表达的客观性入手，通过用主要因子单要素对模糊距离的复合修订，建立了符合环境质量特征和环境质量评价本质要求的复合模糊距离的评价方法和模型，使评价结果突破以往的定性描述而达到准确定量判定。应用实例表明，该方法具有合理性和适用性，实用价值较高     

激光散射法和便携式氢火焰离子化检测器法直读监测油烟排放

餐饮业油烟排放具有排放浓度不稳定、波动较大、排放时间短等特性，存在瞬时排放高值现象，油烟"看得见"和"闻得着"的问题依然存在，因此对油烟实现快速、及时、直读监测尤为必要。基于一种浓度可控且稳定的油烟产生技术，对直读激光散射法与经典手工称重法测定油烟颗粒物浓度值的数据线性关系进行了分析，发现2种方法数值的相关系数达0.99，通过直读修正激光散射法可以有效地测定油烟颗粒物浓度，并测定了不同水汽含量下油烟颗粒物排放情况，发现当相对湿度超过70%时，油烟颗粒物浓度测定值会发生突变。使用便携式氢火焰离子化检测器法（FID）和光离子化检测器法（PID）测定了不同油温下油烟中非甲烷总烃（NMHC）浓度，发现FID对油烟中NMHC的变化反应及时，能够较好地测定油烟中挥发性有机物的排放量。     

室内人造板材制品释放挥发性有机化合物研究

通过对浸渍纸层压木质地板、实木地板、实木复合地板、竹地板、胶合板、细木工板6种共39个人造板材中的挥发性有机物进行定性研究,确定了家用人造板材制品释放的主要挥发性有机物种类,以及人造板材制品中芳香族化合物的主要来源.通过对5间购入新家具的室内环境空气中甲醛、苯、甲苯和总挥发性有机化合物(TVOC)的定量分析,确定了人造板材制品释放挥发性有机化合物的污染水平.研究表明,人造板材释放的挥发性有机化合物以烯烃、芳香族、酯类化合物为主,其中芳香族化合物主要来源于胶合板和细木工板,室内人造板材制品的使用可以使室内环境空气中挥发性有机化合物的质量浓度显著提高.     

A pilot study on the determination of perfluorooctanesulfonate and other perfluorinated compounds in blood of Canadians

A pilot study was conducted to provide preliminary data on the concentrations of perfluorooctanesulfonate (PFOS), perfluorooctanoic acid (PFOA) and perfluorooctanesulfonamide (PFOSA) in the blood of Canadians. A set of 56 human serum samples was collected from non-occupationally exposed Canadians and analyzed by microbore HPLC-negative ion electrospray tandem mass spectrometry. PFOS was the main component of perfluorinated organic compounds (PFCs) and was detected in all 56 blood specimens at an average concentration of 28.8 ng mL(-1) and a range from 3.7 to 65.1 ng mL(-1). The concentration of PFOA was an order of magnitude lower than that of PFOS and was found only in 16 samples (29%) at concentrations above the limit of quantification (LOQ). PFOSA was not detected at levels above the method detection limit (MDL) in any of the samples. The levels of PFCs observed in the sample group of non-occupationally exposed humans in Canada were similar to the levels reported in a previous US study with a similar sample pool size. Two distinct PFOS isomers in human serum were identified by accurate mass determination.     

Evaluation of a standardized method for determining soluble silver in workplace air samples

Several occupational exposure limits and guidelines exist for silver, but the values for each depend on the chemical form of the silver compound in question. In the past, it generally was not possible, without prior knowledge of the work process, to distinguish soluble silver from insoluble silver compounds collected in workplace air samples. Therefore, analytical results were historically reported as total silver. In this study, work was conducted to evaluate a method to differentiate between the quantities of water-soluble silver compounds and total silver collected on filters. The investigation entailed an evaluation of an International Organization for Standardization method to determine soluble silver in airborne particulate matter. The study design incorporated laboratory experiments to evaluate analytical figures of merit, such as selection of appropriate filter media and extraction solution, analytical recovery, and sample stability during storage. Polytetrafluoroethylene (PTFE) filters (2 microm, 37 mm) in opaque cassettes were either spiked with known amounts of silver nitrate or contained a known mass of solid silver nitrate. Results showed that over 90% of the silver was recovered from PTFE filters. Also, field studies were conducted in which workplace air samples were collected in two silver refineries. Some of these samples were analyzed only for soluble silver while others were sequentially extracted and analyzed, first, for soluble silver, then for total silver. The mass fractions of soluble silver, as compared to total silver, were approximately 2% or less. This investigation served to validate an international standard procedure for the determination of soluble silver in workplace air samples.     

Screening organic chemicals in commerce for emissions in the context of environmental and human exposure

Quantitative knowledge of organic chemical release into the environment is essential to understand and predict human exposure as well as to develop rational control strategies for any substances of concern. While significant efforts have been invested to characterize and screen organic chemicals for hazardous properties, relatively less effort has been directed toward estimating emissions and hence also risks. Here, a rapid throughput method to estimate emissions of discrete organic chemicals in commerce has been developed, applied and evaluated to support screening studies aimed at ranking and identifying chemicals of potential concern. The method builds upon information in the European Union Technical Guidance Document and utilizes information on quantities in commerce (production and/or import rates), chemical function (use patterns) and physical-chemical properties to estimate emissions to air, soil and water within the OECD for five stages of the chemical life-cycle. The method is applied to 16,029 discrete substances (identified by CAS numbers) from five national and international high production volume lists. As access to consistent input data remains fragmented or even impossible, particular attention is given to estimating, evaluating and discussing uncertainties in the resulting emission scenarios. The uncertainty for individual substances typically spans 3 to 4 orders of magnitude for this initial tier screening method. Information on uncertainties in emissions is useful as any screening or categorization methods which solely rely on threshold values are at risk of leading to a significant number of either false positives or false negatives. A limited evaluation of the screening method's estimates for a sub-set of about 100 substances, compared against independent and more detailed emission scenarios presented in various European Risk Assessment Reports, highlights that up-to-date and accurate information on quantities in commerce as well as a detailed breakdown on chemical function are critically needed for developing more realistic emission scenarios.