浅析被动采样器监测环境空气质量数据的可比性

对被动采样器与空气自动站监测环境空气质量进行了全年的对比实验,并对大量的监测数据进行了规范的处理分析。结果表明,被动采样器在环境条件持续稳定满足采样条件时,被动采样器与自动站监测结果无显著性差异;在环境条件不能持续稳定满足采样条件时,二者监测结果有显著性差异,但仍有较大的相关性。     

负载咪唑型离子液体硅胶吸附材料制备及应用研究

制备了3种取代咪唑键合的硅胶负载型离子液体(甲基咪唑-SIL、氨丙基咪唑-SIL及十二烷基咪唑-SIL),比较了其对水中双酚A(BPA)的吸附能力。在该研究的实验条件下,BPA在十二烷基咪唑-SIL与水溶液之间的分配系数K_d值高达(2.58±0.02)×10³ L/kg,氨丙基咪唑-SIL、甲基咪唑-SIL的K_d值也分别达到(2.26±0.28)×10、(2.71±0.16)×10 L/kg。采用甲醇为洗脱液,可以对十二烷基咪唑-SIL相中的BPA进行有效回收,2次洗脱的合并回收率为106.7%±4.8%。以十二烷基咪唑-SIL作为被动采样装置的接收相,对污水处理厂出水中BPA进行了被动采样监测应用的微宇宙实验研究。结果表明,在实验周期内,十二烷基咪唑-SIL被动采样器对水体中BPA的被动采集呈线性,其采集速率为0.33 L/d,与以HLB为接收相的商品化被动采样器接近,并且同HLB固相萃取填料相比,离子液体接收相对BPA的采集更具选择性,基质效应较小,可作为被动采样监测装置的理想接收相材料。     

博物馆室内微环境中碱性气体的被动采样方法研究

针对博物馆微环境中的碱性污染气体-氨气，采用自行研制的被动采样器，建立了一套适合博物馆馆藏文物保存环境中氨气含量分析的被动采样-离子色谱检测方法，应用于博物馆的实地采样分析，通过与主动法采样对照，获得了被动采样器在博物馆微环境中氨的吸收系数，从而获得采样点空气中氨气的浓度，为博物馆文物保存环境监测提供了可行方法。     

被动采样在水体中有机污染监测的应用:以PAHs为例

半透膜采样技术是一种可原位、连续、动态监测水环境中非极性、弱极性有机污染物的被动采样技术,已在国内外发展20余年,但在环境监测中使用很少。从半透膜被动采样特点、采样器构造入手,着重对应用该技术的环节进行剖析,同时涉及被动采样结果及其评价方法。最后以多环芳烃（PAHs）为例,综述了近年来SPMD技术监控水体中非极性、弱极性有机污染物的常用分析技术及其发展。     

室内空气中的气态多环芳烃的被动采样监测

利用自制被动采样装置,在2011年秋冬季对南京市部分地区室内空气中5种气态多环芳烃(PAHs)(萘、苊烯、苊、芴、菲)进行了为期100d的连续采样检测,被动采样器的采样速率为0.012m3/d,5种PAHs的回收率在63%～105%之间,方法检出限在1.1～2.4ng范围内。结果表明,南京市5处不同室内环境空气中萘的浓度最高,占总量的90%以上。室内环境空气中5种PAHs的总浓度为230～1564ng/m3。住宅内人体对5种PAHs的暴露速率为479～560ng/h。     

利用Triolein半渗透膜采样技术测定洋河水中的优先污染物

应用Ｔｒｉｏｌｅｉｎ半渗透膜采样器采集了河北洋河宣化至官厅水库河段水样,根据测定采样器中多氯联苯污染物（ＰＣＢｓ）及其它优先污染物浓度,可以估算这些污染物在河段水体中的平均浓度。将结果与同时同地采集的水样,经萃取浓缩后分析得到的结果比较,发现对于不同类型污染物,二者符合程度不同。本研究证明半渗透膜被动采样技术可用于水中多氯联苯等难降解污染物的定量监测,有可能在我国的优先污染物监测工作中发挥作用     

一种淡水大型底栖无脊椎动物采样器研究

研制出一种长方体的十字筐采样器,在采样器内分别填装石、砂、底泥和水草4种基质,利用大型底栖无脊椎动物对生境的选择性进行样本被动采集。基质越多,采样器采集的生物种类越多,生物量也更丰富。用新研制的十字筐采样器和传统的篮式采样器对松花江流域7个采样点进行大型底栖无脊椎动物对比采样,结果显示:十字筐采样器是一种优良的采样器,适合在松花江流域乃至全国推广应用。     

PUF大气被动采样技术对POPs的采样计算

随着《斯德哥尔摩公约》的实施,大气中持久性有机污染物(POPs)的大气被动采样(PAS)观测技术得到了快速发展,相比于传统大气主动采样技术,PAS技术具有明显的优势。以应用最为广泛的聚氨酯软性泡沫材料大气被动采样(PUF-PAS)为例,重点阐述和讨论了3种通过大气被动采样技术来计算污染物在空气中的浓度的方法,并对其采样原理和发展趋势进行了简要介绍。     

废水自动采样器存在偏差原因分析及解决方法

简述了废水自动采样器应用现状。根据废水自动采样器性能指标要求,分析了自动采样器在验收和使用过程中应当重视的几个因素。并通过系列的比对、调查,对机器采样和手工采样可能引起监测结果有所偏差的几个方面进行了探讨,提出了解决这些偏差的一些方法和建议。     

多通道PM_(2.5)采样器的设计及与进口采样器比对测试

设计了多通道大气颗粒物采样器,可同时采集4个通道的PM_(2.5)样品,灵活配置采样通道的开启,每个通道单独设置质量流量计,采用闭环反馈技术,通过比例阀、流量传感器及流量控制板共同控制和校正采样流量,保证通道流量的稳定性。与单通道采样器(BGI PQ 200)进行了为期30 d的比对测试,结果表明,多通道采样器斜率、截距和相关系数均符合《环境空气颗粒物(PM10和PM_(2.5))采样器技术要求及检测方法》(HJ 93—2013)的要求,可满足实际应用需求。     

A new sampler for stratified lagoon chemical and microbiological assessments

A sampler was needed for a spatial and temporal study of microbial and chemical stratification in a large swine manure lagoon that was known to contain zoonotic bacteria. Conventional samplers were limited to collections of surface water samples near the bank or required a manned boat. A new sampler was developed to allow simultaneous collection of multiple samples at different depths, up to 2.3 m, without a manned boat. The sampler was tethered for stability, used remote control (RC) for sample collection, and accommodated rapid replacement of sterile tubing modules and sample containers. The sampler comprised a PVC pontoon with acrylic deck and watertight enclosures, for a 12 VDC gearmotor, to operate the collection module, and vacuum system, to draw samples into reusable autoclavable tubing and 250-mL bottles. Although designed primarily for water samples, the sampler was easily modified to collect sludge. The sampler held a stable position during deployment, created minimal disturbance in the water column, and was readily cleaned and sanitized for transport. The sampler was field tested initially in a shallow fresh water lake and subsequently in a swine manure treatment lagoon. Analyses of water samples from the lagoon tests showed that chemical and bacterial levels, pH, and EC did not differ between 0.04, 0.47, and 1.0 m depths, but some chemical and bacterial levels differed between winter and spring collections. These results demonstrated the utility of the sampler and suggested that future manure lagoon studies employ fewer or different depths and more sampling dates.     

Compact semi-automatic incident sampler for personal monitoring of volatile organic compounds in occupational air

Suddenly occurring and time limited chemical exposures caused by unintended incidents might pose a threat to many workers at various work sites. Monitoring of exposure during such occasional incidents is challenging. In this study a compact, low-weight and personal semi-automatic pumped unit for sampling of organic vapor phase compounds from occupational air during sporadic and suddenly occurring incidents has been developed, providing simple activation by the worker potentially subjected to the sudden occurring exposures when a trained occupational hygienist is not available. The sampler encompasses a tube (glass or stainless steel) containing an adsorbent material in combination with a small membrane pump, where the adsorbent is capped at both ends by gas tight solenoid valves. The sampler is operated by a conventional 9 V battery which tolerates long storage time (at least one year), and is activated by pulling a pin followed by automatic operation and subsequent closing of valves, prior to shipping to a laboratory. The adjustable sampling air flow rate and the sampling time are pre-programmed with a standard setting of 200 mL min(-1) and 30 min, respectively. The average airflow in the time interval 25-30 min compared to average airflow in the interval 2-7 min was 92-95% (n = 6), while the flow rate between-assay precisions (RSD) for six different samplers on three days each were in the range 0.5-3.7%. Incident sampler recoveries of VOCs from a generated VOC atmosphere relative to a validated standard method were between 95 and 102% (+/-4-5%). The valves that seal the sampler adsorbent during storage have been shown to prevent an external VOC atmosphere (500 mg m(-3)) to enter the adsorbent tube, in addition to that the sampler adsorbent is storable for at least one month due to absence of ingress of contaminants from internal parts. The sampler was also suitable for trapping of semi-volatile organophosphates.     

Determination of the dialdehyde glyoxal in workroom air-development of personal sampling methodology

The dialdehyde glyoxal (ethanedial) is an increasingly used industrial chemical with potential occupational health risks. This study describes the development of a personal sampling methodology for the determination of glyoxal in workroom air. Among the compounds evaluated as derivatizing agents; N-methyl-4-hydrazino-7-nitrobenzofurazan (MNBDH), 1,2-phenylenediamine (OPDA), 1-dimethylaminonaphthalene-5-sulfonylhydrazine (dansylhydrazine, DNSH) and 2,4-dinitrophenylhydrazine (DNPH), DNPH was the only reagent that was suitable. Several different samplers were evaluated for sampling efficiency of glyoxal in workroom air using DNPH as derivatizing agent; in-house DNPH coated silica particles packed in two different types of glass tubes, impingers containing acidified DNPH solution, filter cassettes containing glass fibre filters coated with DNPH, a commercially available solid phase cartridge sampler originally developed for formaldehyde sampling (Waters Sep-Pak DNPH-silica cartridge), and the commercially available SKC UMEx 100 passive sampler originally developed for formaldehyde sampling. Aldehyde atmospheres for sampler evaluation were generated with an in-house made vapour atmosphere generator coupled to a sampling unit, with the possibility of parallel sampling. The resulting glyoxal-DNPH derivative was determined using both LC-UV and LC-APCI-MS with negative ionization. By far, the highest recovery of glyoxal was obtained employing one of the in-house DNPH coated silica samplers (93%, RSD = 3.6%, n = 12).     

Comparison of PM10 concentrations in high- and medium-volume samplers in a desert environment

The USEPA replaced TSP with PM₁₀ as the National Ambient Air Quality Standard for particulate matter. The commercially available PM₁₀ sampler is a high-volume model using quartz fiber filters. In certain investigations, such as source apportionment studies, chemical analysis of the filter is necessary, however, many analyses cannot be run on quartz filters. An alternate filter such as Teflon is amenable to XRF and ion chemical analyses but is not amenable to analysis for carbon. To overcome these problems DRI constructed a medium-volume PM₁₀ sampler that is capable of collecting particulates on both Teflon and quartz fiber filters simultaneously. This paper describes the design of the DRI medium-volume PM₁₀ sampler, discusses a method for determining equivalence of two samplers, the results of applying the method to test the equivalence of the medium-volume sampler and a commerical high-volume sampler, and examines differences between PM₁₀ and TSP measurements in a southwestern desert.     

Design and validation of a passive deposition sampler

A new, passive particle deposition air sampler, called the Einstein-Lioy Deposition Sampler (ELDS), has been developed to fill a gap in passive sampling for near-field particle emissions. The sampler can be configured in several ways: with a protective hood for outdoor sampling, without a protective hood, and as a dust plate. In addition, there is an XRF-ready option that allows for direct sampling onto a filter-mounted XRF cartridge which can be used in conjunction with all configurations. A wind tunnel was designed and constructed to test the performance of different sampler configurations using a test dust with a known particle size distribution. The sampler configurations were also tested versus each other to evaluate whether or not the protective hood would affect the collected particle size distribution. A field study was conducted to test the sampler under actual environmental conditions and to evaluate its ability to collect samples for chemical analysis. Individual experiments for each configuration demonstrated precision of the sampler. The field experiment demonstrated the ability of the sampler to both collect mass and allow for the measurement of an environmental contaminant i.e. Cr(6+). The ELDS was demonstrated to be statistically not different for Hooded and Non-Hooded models, compared to each other and the test dust; thus, it can be used indoors and outdoors in a variety of configurations to suit the user's needs.     

Dry deposition study by using dry deposition plate and water surface sampler in Shalu, central Taiwan

This study presents the chemical composition of dry deposition by using dry deposition plate and water surfaces sampler during daytime and nighttime sampling periods at a near highway traffic sampling site. In addition, the characterization for mass and water soluble species of total suspended particulate (TSP), PM2.5 and PM10 were also studied at this sampling site during August 22 to October 31 of 2006 around central Taiwan. The samples collected were analyzed by using Ion Chromatography (DIONEX 100) for the ionic species analysis. Results of the particulate dry deposition fluxes are higher in the water surfaces sampler than that of the dry deposition plate. In other words, the results also indicated that water surface can absorb more ambient dry deposition inorganic pollutants than that of dry deposition plate in this study. The results obtained in this study indicated that the ionic species of Cl(-), NO3(-) and SO4(2-) occupied about average 60-70% downward flux out of total ionic species for either dry deposition plate or water surfaces sampler during August to October of 2006 at this near highway traffic sampling site.     

基于标准雨量计的降水采样方法比较

对太原市2013年7—11月的大气降水使用标准雨量计、国产A型和进口B型自动降水采样设备进行同步记录,分析国产A型和进口B型设备采集降水样品的p H、电导率和无机阴阳离子。结果表明,进口B型设备采集降水样品的降雨量(155.35 mm)比标准雨量计记录值(117.50 mm)高32.21%,而国产A型设备采集降水样品的降雨量(107.12mm)比标准雨量计记录值低8.83%。7—9月的15场降水,国产A型设备采集大多数降水样品的电导率和离子加权浓度均值基本上低于进口B型设备,差异程度分别达65.51%和62.52%;而p H则基本上高于进口B型,酸雨比例差异程度为61.53%。     

Portable XRF analysis of occupational air filter samples from different workplaces using different samplers: final results, summary and conclusions

This paper concludes a five-year program on research into the use of a portable X-ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively-coupled plasma optical-emission spectroscopy (ICP-OES). The filter samples were collected using different filter-holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between-sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP-OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall-deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X-ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.     

Solvent-free sampling with di-n-butylamine for monitoring of isocyanates in air

The solvent-free sampler for airborne isocyanates consisted of a polypropylene tube with an inner wall coated with a glass fibre filter, coupled in series with a 13 mm glass fibre filter. The filters were impregnated with reagent solution containing equimolar amounts of di-n-butylamine (DBA) and acetic acid. Air sampling was performed with an air flow of 0.2 l min(-1). The formed isocyanate-DBA derivatives were determined using liquid chromatography and tandem mass spectrometry. The sampler was investigated in regard to collection principle and extraction of the formed derivatives with good results. The possibility to store the sampler before sampling and to perform long-term sampling was demonstrated. Field extraction of the sampler was not necessary, as there was no difference between immediately extracted samples and stored ones (2 days). In comparative studies, the sampler was evaluated against a reference method, impinger-filter sampling with DBA as reagent. The ratios between the results obtained with the sampler and the reference in a test chamber at a relative humidity (RH) of 45% was in the range of 83-109% for isocyanates formed during thermal decomposition of PUR. At RH 95%, the range was 72-101% with the exception of isocyanic acid. In two field evaluations, the ratios for fast curing 2,4'- and 4,4'-methylene bisphenyl diisocyanate (MDI) was in the range 81-113% and for the 3-ring MDI the range was 54-70%. For the slower curing 1,6-hexamethylene diisocyanate (HDI) and HDI isocyanurate, the ratios were in the range 78-145%. In conclusion, the solvent-free sampler is a convenient alternative in most applications to the more cumbersome impinger-filter sampler.     

大气颗粒物采样器的设计与应用

自行开发设计大气颗粒物双通道采样器,通过更换粒径切割器实现对大气总悬浮颗粒物(TSP)、可吸入颗粒物(PM10)或细颗粒物(PM2.5)样品的采集。该仪器通过流量传感器、比例阀和流量控制板精确控制每个通道的采样流量,控制系统还可实时采集大气环境温度、压力、湿度、风速和风向5个气象参数,并根据环境温度、压力的变化对采样的体积流量进行补偿计算,以确保进样口体积流量恒定,保证粒径切割准确。在2011年深圳大学生运动会期间(8月12—23日)和后期(8月24日至9月4日),利用该仪器进行了大气环境野外观测实验,并对该仪器和Thermo2300采样器的结果进行了平行性分析和对比分析,其平行结果和对比结果相关系数均大于0.99。