Driver speed selection on high-speed two-lane highways: Comparing speed profiles between uniform and differential speed limits

Objective: Although a considerable amount of prior research has investigated the impacts of speed limits on traffic safety and operations, much of this research, and nearly all of the research related to differential speed limits, has been specific to limited access freeways. The unique safety and operational issues on highways without access control create difficulty relating the conclusions from prior freeway-related speed limit research to 2-lane highways, particularly research on differential limits due to passing limitations and subsequent queuing. Therefore, the objective of this study was to assess differences in driver speed selection with respect to the posted speed limit on rural 2-lane highways, with a particular emphasis on the differences between uniform and differential speed limits.

Methods: Data were collected from nearly 59,000 vehicles across 320 sites in Montana and 4 neighboring states. Differences in mean speeds, 85th percentile speeds, and the standard deviation in speeds for free-flowing vehicles were examined across these sites using ordinary least squares regression models.

Results: Ultimately, the results of the analysis show that the mean speed, 85th percentile speed, and variability in travel speeds for free-flowing vehicles on 2-lane highways are generally lower at locations with uniform 65 mph speed limits, compared to locations with differential limits of 70 mph for cars and 60 mph for trucks.

Conclusions: In addition to posted speed limits, several site characteristics were shown to influence speed selection including shoulder widths, frequency of horizontal curves, percentage of the segment that included no passing zones, and hourly volumes. Differences in vehicle speed characteristics were also observed between states, indicating that speed selection may also be influenced by local factors, such as driver population or enforcement.     

Undercounting of large trucks in federal and state crash databases: Extent of problem and how to improve accuracy of truck classifications

Objective: Prior research suggested that single-unit trucks are undercounted when using vehicle body codes in the Fatality Analysis Reporting System (FARS). This study explored the extent of the misclassification and undercounting problem for crashes in FARS and state crash databases.

Methods: Truck misclassifications for fatal crashes were explored by comparing the Trucks Involved in Fatal Accidents (TIFA) database with FARS. TIFA used vehicle identification numbers (VINs) and survey information to classify large trucks. This study used VINs to improve the accuracy of large truck classifications in state crash databases from 5 states (Delaware, Maryland, Minnesota, Nebraska, and Utah).

Results: The vehicle body type codes resulted in a 19% undercount of single-unit trucks in FARS and a 23% undercount of single-unit trucks in state databases. Tractor-trailers were misclassified less often. Misclassifications occurred most frequently among single-unit trucks in the weight classes of 10,001–14,000 pounds.

Conclusions: The amount of misclassification of large trucks is large enough to potentially affect federal and state decisions on traffic safety. Using information from VINs results in more complete and accurate counts of large trucks involved in crashes. The National Transportation Safety Board recommended actions to improve federal and state crash data.     

Features of fatal injuries in older cyclists in vehicle–bicycle accidents in Japan

Objective: The purpose of this study was to identify and better understand the features of fatal injuries in cyclists aged 75 years and over involved in collisions with either hood- or van-type vehicles.

Methods: This study investigated the fatal injuries of cyclists aged 75 years old and over by analyzing accident data. We focused on the body regions to which the fatal injury occurred using vehicle–bicycle accident data from the Institute for Traffic Accident Research and Data Analysis (ITARDA) in Japan. Using data from 2009 to 2013, we examined the frequency of fatally injured body region by gender, age, and actual vehicle travel speed. We investigated any significant differences in distributions of fatal injuries by body region for cyclists aged 75 years and over using chi-square tests to compare with cyclists in other age groups. We also investigated the cause of fatal head injuries, such as impact with a road surface or vehicle.

Results: The results indicated that head injuries were the most common cause of fatalities among the study group. At low vehicle travel speeds for both hood- and van-type vehicles, fatalities were most likely to be the result of head impacts against the road surface.

The percentage of fatalities following hip injuries was significantly higher for cyclists aged 75 years and over than for those aged 65–74 or 13–59 in impacts with hood-type vehicles. It was also higher for women than men in the over-75 age group in impacts with these vehicles.

Conclusions: For cyclists aged 75 years and over, wearing a helmet may be helpful to prevent head injuries in vehicle-to-cyclist accidents. It may also be helpful to introduce some safety measures to prevent hip injuries, given the higher level of fatalities following hip injury among all cyclists aged 75 and over, particularly women.     

A virtual test system representing the distribution of pedestrian impact configurations for future vehicle front-end optimization

Objectives: The purpose of this study is to define a computationally efficient virtual test system (VTS) to assess the aggressivity of vehicle front-end designs to pedestrians considering the distribution of pedestrian impact configurations for future vehicle front-end optimization. The VTS should represent real-world impact configurations in terms of the distribution of vehicle impact speeds, pedestrian walking speeds, pedestrian gait, and pedestrian height. The distribution of injuries as a function of body region, vehicle impact speed, and pedestrian size produced using this VTS should match the distribution of injuries observed in the accident data. The VTS should have the predictive ability to distinguish the aggressivity of different vehicle front-end designs to pedestrians.

Methods: The proposed VTS includes 2 parts: a simulation test sample (STS) and an injury weighting system (IWS). The STS was defined based on MADYMO multibody vehicle to pedestrian impact simulations accounting for the range of vehicle impact speeds, pedestrian heights, pedestrian gait, and walking speed to represent real world impact configurations using the Pedestrian Crash Data Study (PCDS) and anthropometric data. In total 1,300 impact configurations were accounted for in the STS. Three vehicle shapes were then tested using the STS. The IWS was developed to weight the predicted injuries in the STS using the estimated proportion of each impact configuration in the PCDS accident data. A weighted injury number (WIN) was defined as the resulting output of the VTS. The WIN is the weighted number of average Abbreviated Injury Scale (AIS) 2+ injuries recorded per impact simulation in the STS. Then the predictive capability of the VTS was evaluated by comparing the distributions of AIS 2+ injuries to different pedestrian body regions and heights, as well as vehicle types and impact speeds, with that from the PCDS database. Further, a parametric analysis was performed with the VTS to assess the sensitivity of the injury predictions to changes in vehicle shape (type) and stiffness to establish the potential for using the VTS for future vehicle front-end optimization.

Results: An STS of 1,300 multibody simulations and an IWS based on the distribution of impact speed, pedestrian height, gait stance, and walking speed is broadly capable of predicting the distribution of pedestrian injuries observed in the PCDS database when the same vehicle type distribution as the accident data is employed. The sensitivity study shows significant variations in the WIN when either vehicle type or stiffness is altered.

Conclusions: Injury predictions derived from the VTS give a good representation of the distribution of injuries observed in the PCDS and distinguishing ability on the aggressivity of vehicle front-end designs to pedestrians. The VTS can be considered as an effective approach for assessing pedestrian safety performance of vehicle front-end designs at the generalized level. However, the absolute injury number is substantially underpredicted by the VTS, and this needs further development.     

Prediction of vehicle crashes by drivers' characteristics and past traffic violations in Korea using a zero-inflated negative binomial model

Aims: Traffic safety is a significant public health challenge, and vehicle crashes account for the majority of injuries. This study aims to identify whether drivers' characteristics and past traffic violations may predict vehicle crashes in Korea.

Methods: A total of 500,000 drivers were randomly selected from the 11.6 million driver records of the Ministry of Land, Transport and Maritime Affairs in Korea. Records of traffic crashes were obtained from the archives of the Korea Insurance Development Institute. After matching the past violation history for the period 2004–2005 with the number of crashes in year 2006, a total of 488,139 observations were used for the analysis. Zero-inflated negative binomial model was used to determine the incident risk ratio (IRR) of vehicle crashes by past violations of individual drivers. The included covariates were driver's age, gender, district of residence, vehicle choice, and driving experience.

Results: Drivers violating (1) a hit-and-run or drunk driving regulation at least once and (2) a signal, central line, or speed regulation more than once had a higher risk of a vehicle crash with respective IRRs of 1.06 and 1.15. Furthermore, female gender, a younger age, fewer years of driving experience, and middle-sized vehicles were all significantly associated with a higher likelihood of vehicle crashes.

Conclusions: Drivers' demographic characteristics and past traffic violations could predict vehicle crashes in Korea. Greater resources should be assigned to the provision of traffic safety education programs for the high-risk driver groups.     

Exposure factors of Victoria's active motorcycle fleet related to serious injury crash risk

Objective: The purpose of this study was to describe the nature and extent of current powered 2-wheeler (PTW) risk exposures in order to support future efforts to improve safety for this mode of transport.

Methods: A cross-sectional analysis of the control arm of a population-based case-control study was conducted. The control sample was selected from 204 sites on public roads within 150 km of the city of Melbourne that were locations of recent serious injury motorcycle crashes. Traffic observations and measurements at each site were sampled for a mean of 2 h on the same type of day (weekday, Saturday, or Sunday) and within 1 h of the crash time. Photographs of passing riders during this observation period recorded data relating to characteristics of PTWs, age of riders, travel speed of PTWs and all vehicles, time gaps between vehicles, visibility, and protective clothing use.

Results: Motorcycles and scooters represented 0.6% of all traffic (compared with 4% of all vehicle registrations). Riders were significantly more likely to have larger time gaps in front and behind when compared to other vehicles. The average travel speed of motorcycles was not significantly different than the traffic, but a significantly greater proportion were exceeding the speed limit when compared to other vehicles (6 vs. 3%, respectively). The age of registered owners of passing motorcycles was 42 years. Over half of riders were wearing dark clothing with no fluorescent or reflective surfaces. One third of motorcyclists had maximum coverage of motorcycle-specific protective clothing.

Conclusions: A very low prevalence of motorcyclists combined with relatively higher rates of larger time gaps to other vehicles around motorcycles may help explain their overrepresentation in injury crashes where another vehicle fails to give way. An increased risk of injury in the event of a crash exists for a small but greater proportion of motorcyclists (compared to other vehicle types) who were exceeding the speed limit. An apparent shift toward older age of the active rider population may be reducing injury crash risk relative to exposure time. There is significant scope to improve the physical conspicuity of motorcyclists and the frequency of motorcycle specific protective clothing use. These results can be used to inform policy development and monitor progress of current and future road safety initiatives.     

Development of a method to rate the primary safety of vehicles using linked New Zealand crash and vehicle licensing data

Objective: Vehicle safety rating systems aim firstly to inform consumers about safe vehicle choices and, secondly, to encourage vehicle manufacturers to aspire to safer levels of vehicle performance. Primary rating systems (that measure the ability of a vehicle to assist the driver in avoiding crashes) have not been developed for a variety of reasons, mainly associated with the difficult task of disassociating driver behavior and vehicle exposure characteristics from the estimation of crash involvement risk specific to a given vehicle. The aim of the current study was to explore different approaches to primary safety estimation, identifying which approaches (if any) may be most valid and most practical, given typical data that may be available for producing ratings.

Methods: Data analyzed consisted of crash data and motor vehicle registration data for the period 2003 to 2012: 21,643,864 observations (representing vehicle-years) and 135,578 crashed vehicles. Various logistic models were tested as a means to estimate primary safety: Conditional models (conditioning on the vehicle owner over all vehicles owned); full models not conditioned on the owner, with all available owner and vehicle data; reduced models with few variables; induced exposure models; and models that synthesised elements from the latter two models.

Results: It was found that excluding young drivers (aged 25 and under) from all primary safety estimates attenuated some high risks estimated for make/model combinations favored by young people. The conditional model had clear biases that made it unsuitable. Estimates from a reduced model based just on crash rates per year (but including an owner location variable) produced estimates that were generally similar to the full model, although there was more spread in the estimates. The best replication of the full model estimates was generated by a synthesis of the reduced model and an induced exposure model.

Conclusions: This study compared approaches to estimating primary safety that could mimic an analysis based on a very rich data set, using variables that are commonly available when registered fleet data are linked to crash data. This exploratory study has highlighted promising avenues for developing primary safety rating systems for vehicle makes and models.     

Suicide by crashing into a heavy vehicle: Focus on professional drivers using in-depth crash data

Objective: Road traffic suicides typically involve a passenger car driver crashing his or her vehicle into a heavy vehicle, because death is almost certain due to the large mass difference between these vehicles. For the same reason, heavy-vehicle drivers typically suffer minor injuries, if any, and have thus received little attention in the research literature. In this study, we focused on heavy-vehicle drivers who were involved as the second party in road suicides in Finland.

Methods: We analyzed 138 road suicides (2011–2016) involving a passenger car crashing into a heavy vehicle. We used in-depth road crash investigation data from the Finnish Crash Data Institute.

Results: The results showed that all but 2 crashes were head-on collisions. Almost 30% of truck drivers were injured, but only a few suffered serious injuries. More than a quarter reported sick leave following their crash. Injury insurance compensation to heavy-vehicle drivers was just above €9,000 on average. Material damage to heavy vehicles was significant, with average insurance compensation paid being €70,500. Three out of 4 truck drivers reported that drivers committing suicide acted abruptly and left them little opportunity for preventive action.

Conclusions: Suicides by crashing into heavy vehicles can have an impact on drivers’ well-being; however, it is difficult to see how heavy-vehicle drivers could avoid a suicide attempt involving their vehicle.     

Repeatability of a dynamic rollover test system

Objective: The goal of this study was to characterize the rollover crash and to evaluate the repeatability of the Dynamic Rollover Test System (DRoTS) in terms of initial roof-to-ground contact conditions, vehicle kinematics, road reaction forces, and vehicle deformation.

Methods: Four rollover crash tests were performed on 2 pairs of replicate vehicles (2 sedan tests and 2 compact multipurpose van [MPV] tests), instrumented with a custom inertial measurement unit to measure vehicle and global kinematics and string potentiometers to measure pillar deformation time histories. The road was instrumented with load cells to measure reaction loads and an optical encoder to measure road velocity. Laser scans of pre- and posttest vehicles were taken to provide detailed deformation maps.

Results: Initial conditions were found to be repeatable, with the largest difference seen in drop height of 20 mm; roll rate, roll angle, pitch angle, road velocity, drop velocity, mass, and moment of inertia were all 7% different or less. Vehicle kinematics (roll rate, road speed, roll and pitch angle, global Z′ acceleration, and global Z′ velocity) were similar throughout the impact; however, differences were seen in the sedan tests because of a vehicle fixation problem and differences were seen in the MPV tests due to an increase in reaction forces during leading side impact likely caused by disparities in roll angle (3° difference) and mass properties (2.2% in moment of inertia [MOI], 53.5 mm difference in center of gravity [CG] location).

Conclusions: Despite those issues, kinetic and deformation measures showed a high degree of repeatability, which is necessary for assessing injury risk in rollover because roof strength positively correlates with injury risk (Brumbelow 2009). Improvements of the test equipment and matching mass properties will ensure highly repeatable initial conditions, vehicle kinematics, kinetics, and deformations.     

High beam headlamp use rates: Effects of rurality,proximity of other traffic,and roadway curvature

Objective: The few observational studies of the prevalence of high beam use indicate the rate of high beam use is about 25% when vehicles are isolated from other vehicles on unlit roads. Recent studies were limited to 2-lane rural roads and used measurement methods that likely overestimated use. The current study examined factors associated with the rate of high beam use of isolated vehicles on a variety of roadways in the Ann Arbor, Michigan area.

Methods: Twenty observation sites were categorized as urban, rural, or on a rural/urban boundary and selected to estimate the effects of street lighting, road curvature, and direction of travel relative to the city on high beam use. Sites were selected in pairs so that a majority of traffic passing one site also passed through the other. Measurement of high beams relied on video data recorded for 2 nights at each site, and the video data also were used to derive a precise measure of the proximity of other traffic. Nearly 3,200 isolated vehicles (10 s or longer from other vehicles) were observed, representing 1,500-plus vehicle pairs.

Results: Across the sample, 18% of the vehicles used high beams. Seventy-three percent of the 1,500-plus vehicle pairs used low beams at each paired site, whereas 9% used high beams at both sites. Vehicles at rural sites and sites at the boundaries of Ann Arbor were more likely to use high beams than vehicles at urban sites, but use in rural areas compared with rural/urban boundary areas did not vary significantly. Rates at all sites were much lower than expected, ranging from 0.9 to 52.9%. High beam use generally increased with greater time between subject vehicles and leading vehicles and vehicles in the opposing lane. There were mixed findings associated with street lighting, road curvature, and direction of travel relative to the city.

Conclusion: Maximizing visibility available to drivers from headlights includes addressing the substantial underuse of high beam headlamps. Advanced technologies such as high beam assist, which switches automatically between high and low beam headlamps depending on the presence of other traffic, can help to address this problem.     

Analyzing pedestrian crash injury severity under different weather conditions

Objective: Pedestrians are the most vulnerable road users due to the lack of mass, speed, and protection compared to other types of road users. Adverse weather conditions may reduce road friction and visibility and thus increase crash risk. There is limited evidence and considerable discrepancy with regard to impacts of weather conditions on injury severity in the literature. This article investigated factors affecting pedestrian injury severity level under different weather conditions based on a publicly available accident database in Great Britain.

Method: Accident data from Great Britain that are publicly available through the STATS19 database were analyzed. Factors associated with pedestrian, driver, and environment were investigated using a novel approach that combines a classification and regression tree with random forest approach.

Results: Significant severity predictors under fine weather conditions from the models included speed limits, pedestrian age, light conditions, and vehicle maneuver. Under adverse weather conditions, the significant predictors were pedestrian age, vehicle maneuver, and speed limit.

Conclusions: Elderly pedestrians are associated with higher pedestrian injury severities. Higher speed limits increase pedestrian injury severity. Based on the research findings, recommendations are provided to improve pedestrian safety.     

Identifying factors affecting the safety of mid-block bicycle lanes considering mixed 2-wheeled traffic flow

Objective: Electric bikes (e-bikes) have been one of the fastest growing trip modes in Southeast Asia over the past 2 decades. The increasing popularity of e-bikes raised some safety concerns regarding urban transport systems. The primary objective of this study was to identify whether and how the generalized linear regression model (GLM) could be used to relate cyclists' safety with various contributing factors when riding in a mid-block bike lane. The types of 2-wheeled vehicles in the study included bicycle-style electric bicycles (BSEBs), scooter-style electric bicycles (SSEBs), and regular bicycles (RBs).

Methods: Traffic conflict technology was applied as a surrogate measure to evaluate the safety of 2-wheeled vehicles. The safety performance model was developed by adopting a generalized linear regression model for relating the frequency of rear-end conflicts between e-bikes and regular bikes to the operating speeds of BSEBs, SSEBs, and RBs in mid-block bike lanes.

Results: The frequency of rear-end conflicts between e-bikes and bikes increased with an increase in the operating speeds of e-bikes and the volume of e-bikes and bikes and decreased with an increase in the width of bike lanes. The large speed difference between e-bikes and bikes increased the frequency of rear-end conflicts between e-bikes and bikes in mid-block bike lanes. A 1% increase in the average operating speed of e-bikes would increase the expected number of rear-end conflicts between e-bikes and bikes by 1.48%. A 1% increase in the speed difference between e-bikes and bikes would increase the expected number of rear-end conflicts between e-bikes/bikes by 0.16%.

Conclusions: The conflict frequency in mid-block bike lanes can be modeled using generalized linear regression models. The factors that significantly affected the frequency of rear-end conflicts included the operating speeds of e-bikes, the speed difference between e-bikes and regular bikes, the volume of e-bikes, the volume of bikes, and the width of bike lanes. The safety performance model can help better understand the causes of crash occurrences in mid-block bike lanes.     

Impact of improving vehicle front design on the burden of pedestrian injuries in Germany,the United States,and India

Objective: European car design regulations and New Car Assessment Program (NCAP) ratings have led to reductions in pedestrian injuries. The aim of this study was to evaluate the impact of improving vehicle front design on mortality and morbidity due to pedestrian injuries in a European country (Germany) and 2 countries (the United States and India) that do not have pedestrian-focused NCAP testing or design regulations.

Methods: We used data from the International Road Traffic and Accident Database and the Global Burden of Disease project to estimate baseline pedestrian deaths and nonfatal injuries in each country in 2013. The effect of improved passenger car star ratings on probability of pedestrian injury was based on recent evaluations of pedestrian crash data from Germany. The effect of improved heavy motor vehicle (HMV) front end design on pedestrian injuries was based on estimates reported by simulation studies. We used burden of disease methods to estimate population health loss by combining the burden of morbidity and mortality in disability-adjusted life years (DALYs) lost.

Results: Extrapolating from evaluations in Germany suggests that improving front end design of cars can potentially reduce the burden of pedestrian injuries due to cars by up to 24% in the United States and 41% in India. In Germany, where cars comply with the United Nations regulation on pedestrian safety, additional improvements would have led to a 1% reduction. Similarly, improved HMV design would reduce DALYs lost by pedestrian victims hit by HMVs by 20% in each country. Overall, improved vehicle design would reduce DALYs lost to road traffic injuries (RTIs) by 0.8% in Germany, 4.1% in the United States, and 6.7% in India.

Conclusions: Recent evaluations show a strong correlation between Euro NCAP pedestrian scores and real-life pedestrian injuries, suggesting that improved car front end design in Europe has led to substantial reductions in pedestrian injuries. Although the United States has fewer pedestrian crashes, it would nevertheless benefit substantially by adopting similar regulations and instituting pedestrian NCAP testing. The maximum benefit would be realized in low- and middle-income countries like India that have a high proportion of pedestrian crashes. Though crash avoidance technologies are being developed to protect pedestrians, supplemental protection through design regulations may significantly improve injury countermeasures for vulnerable road users.     

Repeatability study of replicate crash tests: A signal analysis approach

Objective: To provide an objective basis on which to evaluate the repeatability of vehicle crash test methods, a recently developed signal analysis method was used to evaluate correlation of sensor time history data between replicate vehicle crash tests. The goal of this study was to evaluate the repeatability of rollover crash tests performed with the Dynamic Rollover Test System (DRoTS) relative to other vehicle crash test methods.

Methods: Test data from DRoTS tests, deceleration rollover sled (DRS) tests, frontal crash tests, frontal offset crash tests, small overlap crash tests, small overlap impact (SOI) crash tests, and oblique crash tests were obtained from the literature and publicly available databases (the NHTSA vehicle database and the Insurance Institute for Highway Safety TechData) to examine crash test repeatability.

Results: Signal analysis of the DRoTS tests showed that force and deformation time histories had good to excellent repeatability, whereas vehicle kinematics showed only fair repeatability due to the vehicle mounting method for one pair of tests and slightly dissimilar mass properties (2.2%) in a second pair of tests. Relative to the DRS, the DRoTS tests showed very similar or higher levels of repeatability in nearly all vehicle kinematic data signals with the exception of global X′ (road direction of travel) velocity and displacement due to the functionality of the DRoTS fixture. Based on the average overall scoring metric of the dominant acceleration, DRoTS was found to be as repeatable as all other crash tests analyzed. Vertical force measures showed good repeatability and were on par with frontal crash barrier forces. Dynamic deformation measures showed good to excellent repeatability as opposed to poor repeatability seen in SOI and oblique deformation measures.

Conclusions: Using the signal analysis method as outlined in this article, the DRoTS was shown to have the same or better repeatability of crash test methods used in government regulatory and consumer evaluation test protocols.     

Modeling the probability of freeway lane-changing collision occurrence considering intervehicle interaction

Objective: To better capture the relationships between lane-changing collisions and explanatory variables, a microscopic model is developed for freeway lane-changing collisions based on the interactions between lane-changing vehicles.

Methods: The model applies an intervehicle interaction structure to account for the occurrence mechanism of lane-changing collisions. The occurrence mechanism can be described as the failure of a vehicle driver of an adjacent lane in avoiding the lane-changing vehicle, which disturbs the smooth movement of the adjacent lane vehicle and requires the driver's brake action to avoid an angle collision. This model is examined using data collected from freeways in Washington State during 2010 to 2011 and validated using lane-changing collision data for the SR 520 freeway.

Results: The findings of this study show that generalized truck percentage has a significant decreasing effect on lane-changing collision risk, whereas average spacing and several roadway characteristics have significant increasing effects. The frequency of slight collisions during peak hours is higher than that during off-peak hours. Young female drivers are more likely to be involved in collisions during lane-changing than young male drivers, but the result for senior drivers is opposite, with older male drivers having a higher probability of lane-changing collisions than female drivers in the same age group.

Conclusion: The process of lane-changing collisions is a complicated maneuver. Truck percentage, average spacing, and good roadway characteristics, such as straight and level segment, in the target lane have a significant effect on the occurrence of lane-changing collisions. Age and gender are also 2 important factors contributing to the relationship between lane-changing collisions and explanatory variables.     

Underutilization of occupant restraint systems in motor vehicle injury crashes: A quantitative analysis from Qatar

Introduction: Restraint systems (seat belts and airbags) are important tools that improve vehicle occupant safety during motor vehicle crashes (MVCs). We aimed to identify the pattern and impact of the utilization of passenger restraint systems on the outcomes of MVC victims in Qatar.

Methods: A retrospective study was conducted for all admitted patients who sustained MVC-related injuries between March 2011 and March 2014 inclusive.

Results: Out of 2,730 road traffic injury cases, 1,830 (67%) sustained MVC-related injuries, of whom 88% were young males, 70% were expatriates, and 53% were drivers. The use of seat belts and airbags was documented in 26 and 2.5% of cases, respectively. Unrestrained passengers had greater injury severity scores, longer hospital stays, and higher rates of pneumonia and mortality compared to restrained passengers (P = .001 for all). There were 311 (17%) ejected cases. Seat belt use was significantly lower and the mortality rate was 3-fold higher in the ejected group compared to the nonejected group (P = .001). The overall mortality was 8.3%. On multivariate regression analysis, predictors of not using a seat belt were being a front seat passenger, driver, or Qatari national and young age. Unrestrained males had a 3-fold increase in mortality in comparison to unrestrained females. The risk of severe injury (relative risk [RR] = 1.82, 95% confidence interval [CI], 1.49–2.26, P = .001) and death (RR = 4.13, 95% CI, 2.31–7.38, P = .001) was significantly greater among unrestrained passengers.

Conclusion: The nonuse of seat belts is associated with worse outcomes during MVCs in Qatar. Our study highlights the lower rate of seat belt compliance in young car occupants that results in more severe injuries, longer hospital stays, and higher mortality rates. Therefore, we recommend more effective seat belt awareness and education campaigns, the enforcement of current seat belt laws, their extension to all vehicle occupants, and the adoption of proven interventions that will assure sustained behavioral changes toward improvements in seat belt use in Qatar.     

Relationship of traffic fatality rates to maximum state speed limits

Objectives: The objective of this study was to examine the safety effects of increases in U.S. state maximum speed limits during the period 1993–2013.

Methods: Poisson regression was used to model state-by-state annual traffic fatality rates per mile of travel as a function of time, the unemployment rate, the percentage of the driving age population that was younger than 25, per capita alcohol consumption, and the maximum posted speed limit on any road in the state. Separate analyses were conducted for all roads, interstates and freeways, and all other roads.

Results: A 5 mph increase in the maximum state speed limit was associated with an 8% increase in fatality rates on interstates and freeways and a 4% increase on other roads. In total, there were an estimated 33,000 more traffic fatalities during the years 1995–2013 than would have been expected if maximum speed limits had not increased. In 2013 alone, there were approximately 1,900 additional deaths—500 on interstates/freeways and 1,400 on other roads.

Conclusions: There is a definite trend of increased fatality risk when speed limits are raised. As roadway sections with higher speed limits have become more ubiquitous, the increase in fatality risk has extended beyond these roadways. The increase in risk has been so great that it has now largely offset the beneficial effects of some other traffic safety strategies. State policy makers should keep this trade-off in mind when considering proposals to raise speed limits.