Effects of work surface and task difficulty on neck–shoulder posture and trapezius activity during a simulated mouse task

Objectives. The purpose of this study is to evaluate the influence of the work surface and task difficulty on the head, upper back and upper arm postures and activity of the descending trapezius during a simulated mouse task. Methods. Healthy female university students (N?=?15) were evaluated. The work surface was positioned at elbow height (EH) and above elbow height (AEH) and the task difficulty was set at low (LD) and high (HD) levels. The postures were recorded by inclinometers. Trapezius activity was normalized by the maximum voluntary isometric contraction (MVIC). Results. Significantly higher head flexion was found at EH compared to the AEH condition, with an average difference of 2°–5° at the same difficulty level. The HD task significantly increased head (3°–6°) and upper back flexion (6°–7°) at the same table height. For upper arm elevation and trapezius activation, the AEH condition presented higher upper arm elevation (about 6°–8°) and trapezius activity (0.8–1.4% of MVIC), regardless of the difficulty level of the task. Conclusions. Head posture was influenced by the table height and task difficulty; the upper back posture by high difficulty; and upper arm posture and trapezius activity were only influenced by table height.     

Infrared thermography reveals effect of working posture on skin temperature in office workers

Introduction. Musculoskeletal symptoms related to using traditional computer workstations are common. Quantitative methods for measuring muscle stress and strain are needed to improve ergonomics of workstations. We hypothesize that infrared thermography (IRT) is suited for this purpose. Methods. This hypothesis was evaluated by estimating muscle activity in upright and traditional working postures with IRT and surface electromyography (sEMG). IRT and sEMG measurements were conducted in 14 female participants with both working postures. First, measurements with the traditional posture were performed. Later, participants had 1?month to adjust to the upright working posture before repeating the measurements. IRT images were acquired before and after a full working day, with sEMG recordings being conducted throughout the measurement days. Participants evaluated their neck pain severity using neck disability index (NDI) questionnaires before the first and after the second measurement day. Results. Spatial variation in upper back temperature was higher (p?=?0.008) when working in traditional posture and the upright working posture reduced (p?p?=?0.003) after working in the upright posture. Conclusion. IRT was found suitable for evaluating muscle activity and upright working posture to reduce the NDI and muscle activity in the upper back.     

An Ergonomie Study on Posture-Related Discomfort Among Preadolescent Agricultural Workers of West Bengal,India

In India, particularly in West Bengal, preadolescents are primarily associated with agricultural work in rural areas. Owing to poor socio-economic conditions, they are compelled to carry out a considerable number of manual, rigorous tasks in agricultural fields. The main aim of this study was to investigate postures adopted by preadolescent agricultural workers during individual agricultural activities and to analyze the causes of discomfort related to those postures. Fifty male and 50 female preadolescent agricultural workers were randomly selected and a detailed posture analysis was performed with the Ovako Working Posture Analysis System (OWAS). It was observed that those workers worked continuously in awkward postures during certain agricultural activities. Consequently they suffered from discomfort in different parts of their body. Even though they were very young, they were likely to suffer from serious musculoskeletal disorders in the future.     

An ergonomic study on posture-related discomfort among preadolescent agricultural workers of West Bengal, India.

In India, particularly in West Bengal, preadolescents are primarily associated with agricultural work in rural areas. Owing to poor socio-economic conditions, they are compelled to carry out a considerable number of manual, rigorous tasks in agricultural fields. The main aim of this study was to investigate postures adopted by preadolescent agricultural workers during individual agricultural activities and to analyze the causes of discomfort related to those postures. Fifty male and 50 female preadolescent agricultural workers were randomly selected and a detailed posture analysis was performed with the Ovako Working Posture Analysis System (OWAS). It was observed that those workers worked continuously in awkward postures during certain agricultural activities. Consequently they suffered from discomfort in different parts of their body. Even though they were very young, they were likely to suffer from serious musculoskeletal disorders in the future.     

Optimization of the levels of grip force,stroke rotation,frequency and grip span for a torqueing task

This study was to investigate the effects of grip force, frequency, stroke rotation and grip-span on discomfort and obtain best posture for hand tool users. Fifteen male participants volunteered in this study. Participants performed combined gripping with torqueing exertions for 5 min for two levels of frequency (10 and 20 exertions/min) at two levels of grip force (50 and 70 N), two levels of stroke rotation (30^○ and 60^○) and three levels of grip-span (4.7, 6 and 7.3 cm). Therefore, a 2×2×2×3 full factorial design was used. The analysis of variance (ANOVA) showed that frequency, stroke rotation and grip-span were significant on discomfort score. Minimum discomfort and comfortable posture was found to be 90 N grip force with 10 exertions/min for 60° stroke rotation at 6-cm grip-span. The grip force, frequency and stroke rotation were found significant on EMG activity of forearm muscles using multivariate analysis of variance (MANOVA). The extensor muscles were found more activated than flexor muscles during the given task.     

A new method for calculating saddle seat height with an emphasis on optimal posture based on trigonometric relations

Introduction. Based on the literature, the ergonomic saddle chair provides the most appropriate posture for users. Determination of the seat height is critical to establish the proper posture, carried out using various methods of anthropometry. This study aimed to develop a simple and applied method for determining the saddle seat height with an emphasis on appropriate posture. Methods. In this study, anthropometric dimensions including weight, body height, popliteal height and seat height at 135° knee angle in 150 male and female dentists were measured. In the laboratory, to determine the ‘acetabuloischial number’, 25 male and female natural hip bones were measured. The mean saddle-chair height with knee angle of 135° was then compared by two different methods, field measurement and the new calculation method. Results. The results showed a strong correlation between data gathered from the two different methods, the field measurement and the new calculation method (98%), and Cronbach’s α from the intraclass correlation was equal to 0.994 (p?<?0.05). This indicated that the two methods produced similar results. Conclusion. The new method can be applied to calculate the optimal height of the saddle seat based on body height and popliteal height.     

An ergonomics study on wrist posture when using laparoscopic tools in four techniques in minimally invasive surgery

Purpose. With reference to four minimally invasive surgery (MIS) cholecystectomies, the aims were (a) to recognize the factors influencing dominant wrist postures manifested by the surgeon; (b) to detect risk factors involved in maintaining deviated wrist postures; (c) to compare the wrist postures of surgeons while using laparoscopic tools. Methods. Video films were recorded during live surgeries. The films were synchronized with wrist joint angles obtained from wireless electrogoniometers placed on the surgeon's hand. The analysis was conducted for five laparoscopic tools used during all surgical techniques. Results. The most common wrist posture was extension. In the case of one laparoscopic tool, the mean values defining extended wrist posture were distinct in all four surgical techniques. For one type of surgical technique, considered the most beneficial for patients, more extreme postures were noticed regarding all laparoscopic tools. We recognized a new factor, apart from the tool's handle design, that influences extreme and deviated wrist postures. It involves three areas of task specification including the type of action, type of motion patterns and motion dynamism. Conclusions. The outcomes proved that the surgical technique which is best for the patient imposes the greatest strain on the surgeon's wrist.?     

Variation in posture quality across musical instruments and its impact during performances

Objective. Bad posture increases the risk that a musician may suffer from musculoskeletal disorders. This study compared posture quality required by different instruments or families of instruments. Methods. Using an ad-hoc postural observation instrument embracing 11 postural variables, four experts evaluated the postures of 100 students attending a Spanish higher conservatory of music. Results. The agreement of the experts’ evaluations was statistically confirmed by a Cohen's κ value between 0.855 and 1.000 and a Kendall value between 0.709 and 1.000 (p?χ² tests revealed significant association between instrument families and seated posture with respect to pelvic attitude, dorsal curvature and head alignment in both sagittal and frontal planes. This analysis also showed an association between instrument families and standing posture with respect to the frontal plane of the axis of gravity, pelvic attitude, head alignment in the frontal plane, the sagittal plane of the shoulders and overall posture. Conclusions. While certain postural defects appear to be common to all families of instruments, others are more characteristic of some families than others. The instrument associated with the best posture quality was the bagpipe, followed by percussion and strings.     

Lower back pain and its association with whole-body vibration and manual materials handling among commercial drivers in Sabah

A cross-sectional study was undertaken to determine the prevalence of lower back pain (LBP) and its association with whole-body vibration (WBV) and manual materials handling (MMH). We studied 110 commercial vehicle drivers using a self-administered questionnaire and the VI-400Pro human vibration monitor. Prevalence of LBP was 66.4%. The percentage of drivers who had frequent manual handling of heavy loads was 45.5% and those who handled heavy loads in awkward postures accounted for 86.4%. Daily vibration A(8) averaged on the z axis was 0.25 (0.06) m·s^?2 and at vector sum was 0.29 (0.07) m·s^?2. Daily vibration exposures on the z axis, frequent manual handling of heavy loads and awkward posture during MMH were significantly associated with LBP. Drivers who are exposed to WBV and frequently handle heavy loads manually and with awkward postures probably have more LBP than drivers who are exposed to only one of these risk factors.     

Posture and belt fit in reclined passenger seats

Abstract

Objective: Highly reclined postures may be common among passengers in future automated vehicles. A laboratory study was conducted to address the need for posture and belt fit in these seating configurations.

Methods: In a laboratory vehicle mockup, the postures of 24 men and women with a wide range of body size were measured in a typical front vehicle seat at seat back angles of 23°, 33°, 43°, and 53°. Data were gathered with and without a sitter-adjusted headrest. Posture was characterized by the locations of skeletal joint centers estimated from digitized surface landmarks.

Results: Regression analysis demonstrated that the pelvis rotated rearward and lumbar spine flexion decreased with increasing recline. The lap portion of the 3-point belt was more rearward relative to the pelvis in more-reclined postures, and the torso portion crossed the clavicle closer to the midline of the body. Regression equations were developed to predict posture and belt fit variables as a function of passenger characteristics, seat back angle, and the use of the headrest.

Conclusions: Spine posture changes as the torso reclines in an automotive seat, and belt fit is altered by the change in posture. The results can be used to accurately position crash test dummies and computation human models and to guide the design of belt restraints.     

Effect of posture on forces and moments measured in a Hybrid III ATD lower leg

Objective: Anthropomorphic test devices (ATDs) are used to assess real injury risk to occupants of vehicles during injurious events. In the lower leg, values from load cells are compared to injury criteria developed in cadaveric studies. These criteria are typically developed with the leg in a neutral posture, whereas the ATD may assume a wide range of postures during safety evaluation tests. The degree to which the initial posture of an ATD has an effect on the measured forces and moments in the lower leg is unknown.

Methods: A Hybrid III ATD lower leg was impacted in a range of postures under conditions representing a crash test, and peak axial force and adjusted tibia index injury measures were evaluated. Ankle posture was varied in 5° increments using a custom-made footplate, and dorsi/plantarflexion (20° DF to 20° PF) and in/eversion (20° IV to 5° EV) were evaluated. Tibia angle was also varied (representing knee flexion/extension) by ±10° from neutral.

Results: Peak axial force was not affected by ankle flexion or tibia angulation. Adjusted tibia index was lowest for plantarflexion, as well as for tibia angles representative of knee extension. Both peak axial force and adjusted tibia index were lowest for postures of great inversion and were highest in neutral or near-neutral postures.

Conclusions: The range of postures tested herein spanned published injury criteria and thus would have made the difference between pass and fail in a safety evaluation. In/eversion had the largest influence on injury metrics, likely due to the change in axial stiffness and altered impact durations in these postures. Results suggest increased injury risk at neutral or near-neutral postures, whereas previous cadaveric studies have suggested that in/eversion does not influence injury risk. It is unclear whether the ATD appropriately represents the natural lower leg for impacts in out-of-position testing. Great care must be taken when initially positioning ATDs for safety evaluations, because small perturbations in posture were shown herein to have large effects on the measured injury risk using this tool.     

Perceptions of postural stability after transitioning to standing among construction workers

Falls are a leading cause of fatal and nonfatal injuries in the construction trades. This study explored construction workers’ self-reports of postural stability upon standing after working in different postures. One hundred and eighty-nine workers in 10 construction trades provided stability ratings by completing a written questionnaire. Additional data collected included age, gender, years of experience, and rating of overall balance. Construction workers rated their overall balance as high, furthermore, no difference was found between trades or age groups. Significant differences in stability ratings were provided for the various postures. The most commonly used non-erect postures (bent over at waist, squatting, and forward kneeling) resulted in the largest self-reports of instability. Sitting on elevated surface and sitting on level surface resulted in the highest levels of self-reported stability and are recommended when maintaining balance is a concern. Differences associated with construction trade and age were also found, but were thought to be attributed to differences in tasks performed since no differences were found when each posture was analyzed separately. The results suggest that the working posture used to complete a task affects the postural stability upon standing regardless of construction trade and age of worker. Findings may lead to recommendations for redesign of tasks or tools to reduce the use of certain working postures, particularly in high-risk environments such as construction.     

Assessment of cervical range of motion,cervical core strength and scapular dyskinesia in violin players

Background. Playing the violin can lead to asymmetric postures which can affect the cervical range of motion, cervical core strength and scapular stability. Objective. The objective of the study was to assess the cervical range of motion, cervical core strength and scapular dyskinesia in violin players and non-players of the same age group. Methods. An inclinometer was used to assess the cervical range of motion, pressure biofeedback was used to assess cervical core strength and scapular dyskinesia was also assessed in 30 professional violin players (18–40 years) compared with 30 age-matched non-players. Analysis was done using an unpaired t test. Results. Significant change was seen with respect to extension (p?=?0.051), cervical core strength (p?=?0.005), right (Rt) superior angle 0° (p?=?0.004), Rt superior angle 45° (p?=?0.015) and Rt inferior angle 90° (p?=?0.013). Conclusion. This study shows a significant difference in extension range of motion and cervical core strength of violin players. Also, there was scapular dyskinesia seen at 0° and 45° right-side superior angle of the scapula and 90° right-side inferior angle of the scapula.     

Comparisons of ergonomic evaluation tools (ALLA,RULA, REBA and OWAS) for farm work

Introduction. The purpose of this study was to validate the agricultural lower limb assessment (ALLA) ergonomic checklist, which was developed for various agricultural tasks in Korea. Methods. One hundred and ninety-six working postures were selected from the real agricultural tasks to verify ALLA, a lower limb body posture assessment tool, and then evaluated by 16 ergonomic experts. Hit rate, quadratic weighted κ, one-way analysis of variance and t-test analyses were applied to compare ALLA with other assessment tools. Results. ALLA analysis had a superior hit rate with ergonomic expert assessment compared with other assessment tools. Quadratic weighted κ analysis also showed that ALLA provided superior estimates of risk levels for farm working postures. Discussion. ALLA would be an appropriate assessment tool to estimate risk factors for various lower limb body postures which frequently occur in agricultural tasks in Korea. ALLA is a simple and accurate risk assessment tool that could be usefully applied to identify and mitigate risk factors and work-related musculoskeletal disorders in agricultural tasks, and also to evaluate the effects of control and intervention for working conditions.     

CAERvest® – a novel endothermic hypothermic device for core temperature cooling: safety and efficacy testing

Introduction. Cooling of the body is used to treat hyperthermic individuals with heatstroke or to depress core temperature below normal for neuroprotection. A novel, chemically activated, unpowered cooling device, CAERvest®, was investigated for safety and efficacy. Methods. Eight healthy male participants (body mass 79.9?±?1.9?kg and body fat percentage 16.1?±?3.8%) visited the laboratory (20 °C, 40% relative humidity) on four occasions. Following 30-min rest, physiological and perceptual measures were recorded. Participants were then fitted with the CAERvest® proof of concept (PoC) or prototype 1 (P1), 2 (P2) or 3 (P3) for 60 min. Temperature, cardiovascular and perceptual measures were recorded every 5 min. After cooling, the CAERvest® was removed and the torso checked for cold-related injuries. Results. Temperature measures significantly (p?Conclusion. This study demonstrates that the CAERvest® is an effective device for reducing body temperature in healthy normothermic individuals without presence of cold injury. Further research in healthy and clinical populations is warranted.     

The Impact of Mobile Data Terminal Use on Posture and Low-Back Discomfort When Combined With Simulated Prolonged Driving in Police Cruisers

The introduction of mobile computing within a constrained vehicle environment has led to changes in the task demands of occupational groups such as professional drivers and law enforcement officers. The purpose of this study was to examine how mobile data terminal (MDT) use interacts with prolonged driving to induce postural changes or low-back discomfort. Eighteen participants (9 male, 9 female) completed two 120-min simulated driving sessions. Time-varying lumbar spine and pelvis postures, seat pan interface pressures and ratings of perceived discomfort were recorded at 15-min intervals. The introduction of a computer interface decreased pelvic posterior rotation by an average of 15° with respect to upright standing and increased peak average discomfort in the neck (5.9 mm), left shoulder (6.8 mm), midback (10.9 mm), low back (10.6 mm) and pelvis (11.5 mm) compared to driving alone. The incorporation of mobile computing warrants consideration in the design of vehicle work environments.     

Epidemiological and biomechanical evaluation of airline baggage handling

Objectives. Musculoskeletal disorders (MSDs) are prevalent among airline baggage handlers due to manual materials handling. In this study, the Nordic musculoskeletal questionnaire (NMQ), the revised National Institute for Occupational Safety and Health (NIOSH) lifting equation, and the University of Michigan 3D Static Strength Prediction Program? (3DSSPP) were used to analyze MSDs among baggage handlers. Methods. The NMQ was filled out by 209 baggage handlers and 46 arbitrarily selected baggage handlers were evaluated using the NIOSH method and 3DSSPP. Results. The obtained results showed that the most common MSDs occurred in the lower back region. The next risky regions included knees, neck, and upper back, respectively. The NIOSH results confirmed that the subjects lifted loads heavier than the permitted limit and their lifting postures were inappropriate. The results of the 3DSSPP also indicated that compression forces exceeded the NIOSH limit in these awkward postures. Conclusions. Relying on this study, holding compulsory ergonomic lifting training courses could be proposed for workers and regulations adjusting an upper limit for maximum baggage weight must be also enacted in order to improve occupational health and prevent the prevalence of increasing MSDs.     

Anthropometric hand dimensions in a population of Iranian male workers in 2012

Background. The mismatch between the hand size of workers and the size of industrial instruments is a growing concern; it can lead to various musculoskeletal complications. Currently, there are few reliable studies available to address this concern in Iran. This study was conducted to measure 30 upper-extremity parameters in a group of Iranian industrial workers. Methods. This study is a cross-sectional study on 529 workers. The study population was randomly selected from male Iranian industrial workers who were referred to the Yazd hospital occupational medicine clinic for surveillance evaluations. Results. The M (SD) age of the participants was 30.13 (8.29) years. Statistical analysis was performed using the mean, standard deviation and 5th, 50th and 90th percentiles for each measured hand dimension. A considerable number of dimensions were significantly different between the measurements of right and left hands in each examinee. The results showed significant differences between Iranian hand size and that of other populations. Conclusion. This study provided a valuable databank of hand dimensions in a population of Iranian male workers. These data can be used by manufacturers in designing high-quality hand-tools and industrial gloves, taking into consideration Iranian worker characteristics.     

Occupational noise exposure and hearing defects among sawmill workers in the south of Thailand

The aim of this study was to investigate occupational noise exposure and hearing defects among sawmill workers in the south of Thailand. Seven hundred sawmill workers participated, of which 335 (47.9%) were male. The mean age of the sawmill workers was 33.5 years (SD 10.2), and more than 60% were <35 years old; 75.1% of the workers had less than 5 years of work experience. Only about one in four workers (25%) had been trained in use of personal protective equipment (PPE), and half of the participants never or rarely wore PPE while working. The prevalence rate of noise-induced hearing loss (NIHL) was 22.8% (N?=?42). Male workers had significantly higher risk than female workers (odds ratio [OR]?=?2.21). Workers aged older than 25 years had significantly higher risks for NIHL (OR?=?3.51–12.42) than workers younger than 25 years. Sawing workers had higher risk for NIHL than office workers (OR?=?3.07).