Calorimetric behaviors of N2H4 by DSC and superCRC

The objective of this study is to obtain information about the thermal decomposition behaviors of hydrazine (N₂H₄) caused by metals, using differential scanning calorimeter (DSC) and SuperCRC. The DSC measurements revealed that the exothermic reactions of N₂H₄ were caused by the reaction conditions such as the type of cells; the T_DSC with a gold pan is 485.2 K and that with a glass capillary is 620.5 K. Besides, the activation energy of the thermal decomposition of N₂H₄, calculated from the Kissinger and Ozawa methods, were found to be about 38±2 kJ mol⁻¹ in the gold pan and 141±8 kJ mol⁻¹ in the glass capillary. Moreover, a heat flow profile was observed with SuperCRC during the mixing of N₂H₄ and the metal ion solution at 298 K. The maximum heat flow was related to the metal ion oxidative characters. The higher oxidative characters would provide a faster acceleration for the exothermic behavior than the lower oxidative ions. Based on this study, Mn(VII) and Cr(VI) were considered to exhibit strongly oxidative characteristics during mixing with N₂H₄.     

Pretreatment of municipal landfill leachate by a combined process

Biodegradability enhancement of landfill leachate using air stripping followed by coagulation/ultrafiltration (UF) processes was introduced. The air stripping process obtained a removal efficiency of 88.6% for ammonia nitrogen (NH₄–N) at air-to-liquid ratio of 3500 (pH 11) for stripping 18 h. The single coagulation process increased BOD/COD ratio by 0.089 with the FeCl₃ dosage of 570 mg l^?1 at pH 7.0, and the single UF process increased the BOD/COD ratio to 0.311 from 0.049. However, the combined process of coagulation/UF increased the BOD/COD ratio from 0.049 to 0.43, and the final biological oxygen demand (BOD), chemical oxygen demand (COD), NH₄–N and colour of leachate were 1223.6 mg l^?1, 2845.5 mg l^?1, 145.1 mg l^?1 and 2056.8, respectively, when 3 kDa molecular weight cut-off (MWCO) membrane was used at the operating pressure 0.7 MPa. In ultrafiltration process, the average solution flux (J_V), concentration multiple (M_C) and retention rate (R) for COD was 107.3 l m^?2 h^?1, 6.3% and 84.2%, respectively.     

Fate of trace tetracycline with resistant bacteria and resistance genes in an improved AAO wastewater treatment plant

The fate of trace tetracycline, tetracycline resistant bacteria (TRB) and tetracycline resistant genes (TRGs) in an improved anaerobic-anoxic-oxic (AAO) wastewater treatment plant (WWTP) was investigated in this study. Quantitative real-time polymerase chain reaction (qPCR) and conventional heterotrophic plate count method were used to measure eight tet genes (tetA, tetB, tetC, tetE, tetM, tetO, tetS and tetX) and TRB, respectively. The TRB percent of total heterotrophic bacteria (THB) is about 1.31–24.1% in WWTP influent. Tet gene abundance in the WWTP varied greatly among the gene types. The concentrations of TRGs in effluent samples ranged from 7.11 × 10⁻⁹ to 1.53 × 10⁻⁴ copies/copy 16S rRNA gene. TRB and THB, tetM and tetO, tetE and tetX, but not the others, showed a significant correlation with each other (p < 0.01). The relationships between ribosomal protection protein genes, enzymatic modification gene and corresponding concentrations of antibiotics were found to be considerably significant (R² = 0.898, p < 0.01 for ribosomal protection protein genes and R² = 0.872, p < 0.05 for enzymatic modification gene).     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Optimization of Innovative Ethanol Production from Wheat by Response Surface Methodology

A soft wheat variety has been tested as the raw material for fuel ethanol production via a novel processing route. The bran stream produced by the break section of a Buhler mill was used as the sole nutrient source in solid-state fermentation for the production of hydrolytic enzymes by two fungal strains, Aspergillus awamori and Aspergillus oryzae. Co-fermentation of the two fungi was largely problematic because of a significant difference between their growth rates. A mixture of the two enzyme solutions produced by separate cultivation of the two strains was effective for simultaneous starch and protein hydrolyses. Response surface methodology was used to design ethanol production trials using the flour hydrolysate as the only nutrient source by Saccharomyces cerevisiae. In a medium containing 150 g l⁻¹ glucose and 310 mg l⁻¹ free amino nitrogen, ethanol yield on glucose reached 50.7%, i.e., 99.2% of the theoretical conversion ratio, in 72 h. The yield of CO₂ from glucose was approximated as slightly higher than its theoretical yield due possibly to the availability of O₂ in the early fermentation stage. The overall production of 2-methyl-1-butanol, 1-propanol, 2-methyl-1-propanol and 3-methyl-butanol in all trials of yeast fermentation remained below 1000 ppm. Mass balance calculation concluded conversion ratios of 29.61% (w/w) ethanol and 23.74% (w/w) CO₂ from the wheat.     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

7 mT static magnetic exposure enhanced synthesis of poly-3-hydroxybutyrate by activated sludge at low temperature and high acetate concentration

The effect of 7 mT (milliTesla) SMF (static magnetic field) on poly-3-hydroxybutyrate (PHB) production was studied at an acetate concentration of 260 Cmmol l^?1 and temperature of 10 °C. The SMF decreased the specific acetate uptake rate by 29%, but increased the maximum PHB content and the yield of PHB on acetate by 32 and 28% respectively. The ratio q_P/(q_S ? q_P), which described specific PHB production rate over the difference between specific acetate uptake rate and specific PHB production rate, was introduced for evaluation of the ratio of carbon flux into PHB synthesis and into the TCA (tricarboxylic acid) cycle. This value reached 2.3 when activated sludge culture was exposed to magnetic field of 7 mT, which was 1.1 times higher than the q_P/(q_S ? q_P) value obtained without magnetic exposure. Therefore, the SMF promoted diversion of more acetyl-CoA towards PHB synthesis and could offset adverse effects of high acetate concentration and low temperature. These results provide evidence that SMF enhances PHB production by activated sludge.     

Removal mechanism of trace oxytetracycline by aerobic sludge

To investigate the mechanism of removal of selected pharmaceuticals in activated sludge systems, laboratory-scale batch experiments were conducted to assess the adsorption and degradation behavior of trace oxytetracycline (OTC). The adsorption equilibrium of OTC was observed in 30 min and the adsorption process could be well described by a pseudo-second-order model with a rate of 0.362 L μg^?1 min^?1. The OTC adsorption rate decreased with increasing temperature and could be fitted by the Freundlich isotherm. The linear partition coefficients (K_d) were 1.19, 0.999, and 0.841 L g^?1 at temperatures of 15, 20, and 25 °C, respectively. Thermodynamic analysis revealed that the adsorption of OTC onto the inactivated sludge was spontaneous (ΔG = ?16.7 to ?17.0 kJ mol^?1), enthalpy-driven (ΔH = ?24.9 kJ mol^?1), entropy-retarded (ΔS = ?27.4 J (mol K)^?1), and predominantly a physical adsorption.     

Partial nitritation of landfill leachate with varying influent composition under intermittent aeration conditions

The start-up and operation of a partial nitritation sequencing batch reactor for the treatment of landfill leachate were carried out on intermittent aeration mode. Partial nitrite accumulation was established in 15 days after the mode was changed from continuous aeration to intermittent aeration. Despite the varying influent composition, partial nitritation could be maintained by adjusting the hydraulic retention time (HRT) and the air flow rate. An increase in the air flow rate together with a decrease in air off duration can improve the partial nitritation capacity and eventually result in the development of granular sludge with fine diameters. A nitrogen loading rate of 0.71 ± 0.14 kg/m³/d and a COD removal rate of 2.21 ± 0.13 kg/m³/d were achieved under the conditions of an air flow rate of 19.36 ± 1.71 m³ air/m³/h and an air on/off duration of 1.5 min/0.7 min. When the ratio of total air flux (TAF) to the influent loading rate (ILR) was controlled at the range of 163–256 m³ air/kg COD, a stable effluent NO₃^?–N/NO_x^?–N (NO₂^?–N plus NO₃^?–N) ratio below 13% was achieved. Interestingly, the effluent pH was found to be a good indicator of the effluent NO₂^?–N/NH₄⁺–N ratio, which is an essential parameter for a subsequent anaerobic ammonium oxidation (Anammox) reactor.     

Thermal characterization of fly ash from one municipal solid waste incinerator (MSWI) in Shanghai

This study aims to develop a methodology for the thermal characterization of MSWI fly ash. We performed TGA–DTA and component variation analysis, microstructure transfer of sintered fly ash, as well as leaching toxicity, volatilization ratio and specification transformation of heavy metals as a function of temperature. It is found that content of crystal phases first increases between room temperature and 800 °C and then decreases between 800 °C and 1200 °C, while that of glass phases registers a reverse trend. Fly ash registers a SiO₂–Al₂O₃–metal oxides system and its content of glass phases is around 57%. Increase of sintering temperature between 600 °C and 1200 °C is conducive to the reduction of soluble As, Cd, Cu, Hg, Pb, Ni and Zn, while content of soluble Cr increases as temperature rises from 800 °C to 1200 °C.     

Effects of applied voltage on hydrogen production rate of a single reactor BML with Clostridium sp.

This study aimed to explore the influences of single-chamber systems with different applied voltage on bio-hydrogen (H₂) production. The reactor used was the bio-electrochemically assisted microbial reactor (BEAMR) membrane-less (BEAMR-membrane-less, BML). The microbial dark fermentative H₂ production method was adopted. After the hot screening process and the DNA sequencing, the domesticated dominant microflora was Clostridium sp. This study discussed the influences of the cases with (continuous and intermittent) and without applied voltage separately. The results showed that, the H₂ production rate of the case with intermittent applied voltage (117 mL/h g VSS) of 0.24 V was increased of 1.7 folds higher than the without applied voltage (69 mL/h g VSS) and 1.3 folds higher than the case with continuous applied voltage (88.2 mL/h g VSS) of 0.24 V. The produced H₂ concentration with intermittent applied voltage was 18.9% (18.6–19.1%) higher than the without applied voltage, while there was no significant difference with continuous applied voltage.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Hydrogen sulphide removal from landfill gas

Control of odours should be considered to be a fundamental issue in order to site, design and manage sanitary landfills. With regard to construction and demolition (C&;D) debris, landfilling was the mainly adopted solution in many European Countries; in particular, gypsum drywalls can produce high concentrations of hydrogen sulphide (H₂S) in landfill gas ranging from 7 ppm to 100 ppm. In some cases also dangerous concentrations until to 12,000 ppm were detected. In this paper H₂S removal efficiency in a lab-scale vertical packed scrubber was investigated. Hydrogen sulphide abatement was evaluated for inlet H₂S concentrations of 1000–100–10 ppm, adjusting scrubbing liquid pH in the range 9–12.5 by means of caustic soda (NaOH 2N solution). Moreover, best operating conditions for the system were defined as well as H₂S abatement along the tower and liquid recirculation effectiveness in case of inlet H₂S concentration of 10 ppm (typical odour concentration). Results showed that pH of 11.5 in scrubbing liquid could be considered the best value for removal of different inlet H₂S concentrations, also taking into account parasitical consumption of NaOH due to CO₂ absorption. Moreover, in case of continuous working of the system at H₂S concentration of 10 ppm, strong removal efficiency was already obtained with a packed bed height of about 70 cm. Significant performances were ensured after 1 h of constant activity, consuming about 3 ml of soda per cubic meter of polluted air. Subsequently liquid blowdown was necessary.     

Comparative response of two organic biofilters treating ethylbenzene and toluene after prolonged exposure

The response of two biofilters filled with an organic waste material for treating ethylbenzene and toluene was studied for 415 and 472 operating days, respectively. The peak elimination capacities (EC_MAX) recorded were 170 g m^?3 h^?1 for ethylbenzene (EC_MAX) and 138 g m^?3 h^?1 for toluene. Regarding the degradation profile through the biofilters, an increase in the inlet concentration displaced the degradation profile into the downstream section. A sudden decrease in the performance of both biofilters occurred when the moisture content (MC) of the packing material exceeded 37% for ethylbenzene and 30% for toluene. Thus, a recommended MC value was established in the 15–30% range. Given the bioreactor was operated at a low MC level, fungi prevailed over bacteria. Nevertheless, synergism was detected between both microorganism types for the mineralization of the aromatic hydrocarbons.     

Low-dose irradiation by electron beam for the treatment of high-SOx flue gas on a semi-pilot scale—Consideration of by-product quality and approach to clean technology

Attention has been focused on the treatment of lignite-fired flue gas in order to use lignite in an environmentally friendly way – (i) low-CO₂ emission, (ii) production of a valuable by-product, (iii) no discharge of wastewater, (iv) direct removal of SO₃ (strong toxicity), and (v) treatment of high SO₂ concentration. Based on these criteria, electron beam irradiation with ammonia injection was tested on a semi-pilot scale: 800 Nm³ h^?1 flow rate, 5500 ppm SO₂, 70 ppm NO_x, 22% flue gas moisture, and 75–80 °C at the reactor outlet.As an energy-saving measure, a low dose (5 kGy) of irradiation was applied: the problem lay in the by-product quality. It is considered that (NH₄)₂SO₃ and NH₄HSO₃ produced by thermal reactions are oxidized to form (NH₄)₂SO₄ (fertilizer) by an electron beam. However, not all reactions were complete because the by-product contained small amounts of H₂SO₄ and NH₂SO₃NH₄ (herbicide), so a vegetable pot test was performed to study the by-product quality: no adverse effect was observed. It is inferred from the pot test that slightly acidic soil may protect vegetables from disease and a small amount of NH₂SO₃NH₄ probably affects woody species and not herbaceous species.It is concluded that the electron beam system is noted as a multi-component pollution control process (removal of NO_x, SO₃, SO₂ and dioxins) and this system will contribute to environmentally friendly use of lignite as well as agricultural productivity via fertilizer supply.     

Achieving stable partial nitritation using endpoint pH control in an SBR treating landfill leachate

The feasibility of using endpoint pH control to achieve stable partial nitritation (PN) in an SBR for landfill leachate treatment was investigated. By imposing a fixed-time anoxia followed by variable-time aeration in an SBR cycle, successful partial nitritation was maintained for 182 days at a nitrogen loading rate of 0.30–0.89 kg/m³/day. The effluent NO₂⁻-N/NH₄⁺-N ratio and the effluent NO₃⁻-N concentration were 1.30 ± 0.22 and 16 ± 9 mg/L, respectively. High free ammonia (FA) and low dissolved oxygen (DO) concentrations were inhibition factors of nitrate formation. The termination of aeration at a suitable endpoint pH was the key to achieve an effluent NO₂⁻-N/NH₄⁺-N ratio close to the stoichiometric value. This endpoint pH control strategy represents practical potentials in the engineered application of combined PN–ANAMMOX processes.     

Optimizing the preparation parameters of mesoporous nanocrystalline titania and its photocatalytic activity in water: Physical properties and growth mechanisms

Titania nanomaterial with an anatase structure and 5.6 nm crystallite size and 280.7 m² g⁻¹ specific surface areas had been successfully prepared by sol–gel/hydrothermal route. The effect of pH as a type of autoclave and calcination was studied. Crystallite size and phase composition of the prepared samples were identified. X-ray diffraction analyses showed the presence of anatase with little or no rutile phases. The crystallite size of the prepared TiO₂ with acidic catalyst was both smaller than that prepared with basic catalyst, and was increasing after acidic calcinations by a factor 4–5. Basic calcinations produced a specific increase of 1.5. Rutile ratio and the particle size were increased after calcination at 500 °C. However, TiO₂ powder synthesized using a basic catalyst persisted the anatase phase and a loosely aggregation of particles. Anatase TiO₂ as prepared with acidic catalyst in Teflon lined stainless steel autoclave demonstrated the highest photocatalytic activity for degradation of 2,6-dichlorophenol-indophenol under ultraviolet irradiation with t_½ 0.8 min.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Young drivers' perceptions of culpability of sleep-deprived versus drinking drivers

Introduction: Sleep-deprived driving can be as dangerous as alcohol-impaired driving, however, little is known about attitudes toward sleep-deprived drivers. This study examined the extent to which young drivers regard sleep-deprived compared to drinking drivers as culpable for a crash, and how their perceptions of driving while in these conditions differ. Method: University student participants (N = 295; M = 20.4 years, SD = 1.3; 81% women) were randomly assigned to read one of five fatal motor-vehicle crash scenarios, which differed by aspects of the driver's condition. Culpability ratings for the drinking driver were higher than those for the sleep-deprived driver. Results: Qualitative findings revealed that driving while sleep-deprived was viewed as understandable, and driving after drinking was viewed as definitely wrong. The dangers of sleep-deprived driving remain under-recognized.