条形障碍物对瓦斯爆炸特性影响研究

我国煤矿瓦斯爆炸事故不断出现,造成了巨大的人员伤亡和经济损失,在置障条件下研究瓦斯爆炸特性,对预防和减少瓦斯爆炸事故具有重要意义。利用水平管道式爆炸试验装置,研究密闭管道内条形障碍物的数量和阻塞率对管道内瓦斯最大爆炸压力、火焰速度、最大爆炸压力上升速率和爆炸指数的影响以及敞口状态的影响。研究表明:障碍物对瓦斯爆炸具有显著激励作用,管道内瓦斯最大爆炸压力、火焰速度、最大爆炸压力上升速率和爆炸指数均显著增大,随着障碍物数量和阻塞率的增加,激励作用越明显;敞口状态下管道内最大爆炸压力、最大爆炸压力上升速率和爆炸指数均显著减小,火焰持续传播。研究结果对防治煤矿瓦斯爆炸事故提供一定的理论支持。     

瓦斯对煤尘爆炸特性影响的实验研究

瓦斯的存在对煤尘爆炸特性的理论计算和数值仿真的结果与实际数据有一定差距,因此,通过不同浓度瓦斯与煤尘共存条件下爆炸实验研究,得出了矿井瓦斯对煤尘的最低着火温度、最小点火能量、爆炸下限浓度、最大爆炸压力和最大爆炸压力上升速度等爆炸特性影响的规律即瓦斯对煤尘最低着火温度影响不大;瓦斯可使煤尘的最小点火能量减小,尤其是对难于点燃的煤尘;混合物的爆炸下限浓度随瓦斯浓度的增加而降低;混合物的最大爆炸压力上升速度由于瓦斯的存在而增强,而最大爆炸压力几乎没有变化。同时研究了瓦斯对无爆炸性煤尘的影响。实验研究的结论对于现场防止煤尘爆炸的发生具有指导意义。     

泄压点火不同端管道内甲烷爆炸特性数值模拟

结合气体爆炸传播机理,利用FLACS软件对泄压点火不同端两种方式(泄压口通径为25 mm和泄压口完全开放)下甲烷的爆炸过程进行数值模拟,获得了5种体积分数甲烷的爆炸特性参数,分析得出:两种不同泄压方式下,10%,9.5%,11%体积分数的甲烷爆炸特性变化趋势接近,7%,8%的甲烷较前三者有所延迟;5种甲烷在管道中心处的最大爆炸压力、最大爆炸压力上升速率、最大爆炸压力下降速率、温度峰值都随甲烷体积分数的增大而逐渐上升,在10%时达到最大,继续增加甲烷体积分数则出现下降趋势,最大爆炸压力时间变化趋势与其相反;管道中心处的爆炸产物浓度随着甲烷体积分数的增大而增大,与泄压方式无关;增大管道泄压口面积有利于爆炸压力以及爆炸高温高压气体的释放,使得各体积分数甲烷的最大爆炸压力、最大爆炸压力上升速率、最大爆炸压力下降速率、温度峰值均下降,到达最大爆炸压力的时间均增大。     

水平管道内障碍物数量对瓦斯爆炸过程的影响研究

为了研究水平管道内障碍物数量对瓦斯爆炸的影响,利用自制的水平管道式气体爆炸试验装置,选用阻塞率为60%的圆环型障碍物,在常温常压下对管道内障碍物数量分别为1片、3片、5片和7片时瓦斯(试验气体为甲烷与空气的混合物,下同)爆炸过程进行试验研究。结果表明:瓦斯的爆炸压力及其上升速率均随障碍物数量的增加呈先增后减的变化规律,而火焰传播速度则随着障碍物数量的增加单调递增,但递增幅度逐渐减小。在密闭置障管道内瓦斯的爆炸压力及其上升速率随测试位置长径比的增大先减小后增大,而火焰传播速度则随测试位置长径比的增大单调递减。     

以氢气为主要成分的其他可燃气体对低浓度甲烷爆炸特性的影响

为研究矿井火区中一氧化碳(CO)、氢气(H_2)、乙烯(C_2H_4)和乙烷(C_2H_6)等其他可燃气体对甲烷(CH_4)爆炸特性的影响,利用可视球形气体爆炸系统开展了多元可燃气体爆炸压力特性试验,观察并分析了峰值爆炸压力、最大爆炸压力上升速率及其相应时间。通过高速摄影系统拍摄了视窗范围内爆炸火焰传播图像,基于边缘检测方法确定了火焰前锋位置,继而得到最大火焰传播速度。分析了以氢气为主要成分的其他可燃气体对低浓度CH_4-空气混合物压力特性和火焰传播行为的影响。结果表明,多元可燃气体的存在增加了低浓度CH_4-空气混合物的爆炸危险性。随混合气体体积分数增加,低浓度CH_4-空气混合物的峰值爆炸压力、最大爆炸压力上升速率和最大火焰传播速度非线性增加;此外,到达峰值爆炸压力、最大爆炸压力上升速率的时间显著缩短。     

密闭容器甲烷-空气混合物爆炸的尺寸效应

为探究密闭容器甲烷爆炸的尺寸效应及其变化特征,以及预防和控制密闭容器甲烷爆炸事故,通过改变圆柱形容器体积和管道的长度和直径,研究密闭容器甲烷-空气混合物爆炸压力变化特性;采用多元线性回归模型,分析最大爆炸压力及最大压力上升速率与管径和管长的关系。结果表明:在圆柱形容器中,最大爆炸压力上升速率随容器体积的增大而减小;随着管道内径的增加,管道末端的最大爆炸压力和最大爆炸压力上升速率均下降;管道长度增加,管道末端最大爆炸压力和最大爆炸压力上升速率均增加。试验得到最大爆炸压力及最大压力上升速率的无量纲预测模型。     

瓦斯煤尘爆炸特性及传播规律研究进展

概要介绍国内外的瓦斯爆炸和瓦斯煤尘混合物爆炸特性及传播规律研究进展,瓦斯爆炸研究主要集中在瓦斯爆炸压力、火焰、温度等特征参数、不同障碍物对瓦斯爆炸压力、火焰传播的影响以及分岔、拐弯等不同形状管道内的传播规律,而瓦斯煤尘混合物爆炸研究主要集中在瓦斯对煤尘爆炸的最小点火能、爆炸下限、最大爆炸压力等爆炸特性及传播规律的影响。对不同研究人员采用的主要研究指标、手段、方法和研究结论进行综合评述,同时也对爆炸事故人员伤害模型在国内外的研究状况进行讨论,最后指出目前存在的主要问题和下一步的研究方向。     

高炉喷吹用贫瘦煤爆炸强度的实验研究

在20 L球的密闭容器中,对4种潞安贫瘦煤的爆炸强度进行了系统的实验研究.分析了煤粉质量浓度对爆炸后最大爆炸压力、最大压力上升速率的影响,并计算出相应的爆炸指数.实验数据表明,最大爆炸压力和最大压力上升速率都随煤粉质量浓度的增加先增大后减小,4种煤粉中常村喷吹煤最大爆炸压力最大,为0.7419 MPa;漳村喷吹煤最大压力上升速率最大,为43.54 MPa/s.爆炸指数都在9～12之间,均小于爆炸指数分级中对弱爆炸性定义的指标20.可知4种煤粉都属于弱爆炸性煤,可以比较安全的用于高炉喷吹.     

多孔聚丙烯复合材料的抑爆性能研究

为分析填充多孔材料对管道中瓦斯爆炸压力的抑制效果,采用自主搭建的气体爆炸测试平台,试验研究多孔聚丙烯复合材料的内径、填充位置和填充长度等参数影响瓦斯爆炸压力的机制。结果表明:与空管道爆炸状态比较,填充多孔材料后最大爆炸压力、最大爆炸压力上升速率都明显降低;当填充多孔材料为实心,即内径为0 mm,填充在距离点火源最近处、填充长度为2 m时,管道末端最大爆炸压力值衰减69.64%,最大爆炸压力上升速率降低58.31%,对瓦斯爆炸压力的抑爆效果最佳;改变材料内径、填充位置和填充长度等因素均会对多孔材料的抑爆性能产生显著影响。     

长管中立体障碍物对瓦斯爆炸特性影响的研究

管道内可燃气体火焰传播与障碍物相互作用的过程的研究对爆炸场所预估和防爆工程设计具有重要的意义,在实际生产、生活中,火焰传播方向上的障碍物往往具有立体结构,基本没有平面结构,因此,利用长管密闭容器,在立体障碍物存在的条件下,研究了瓦斯爆炸压力和火焰传播速度。研究结果表明:随着障碍物数量的增加,瓦斯爆炸压力和火焰传播速度随之增大;阻塞率增加,瓦斯爆炸压力和火焰传播速度出现先增大后减小的现象,当阻塞率为50%时,其爆炸压力和火焰传播速度达到最大;障碍物的摆放形式对瓦斯爆炸压力和火焰传播速度也有一定的影响。     

激波诱导下煤粉的爆炸压力测试

因气体爆炸导致沉积粉尘的二次爆炸的威力远大于单纯的气体或者粉尘爆炸产生的威力,利用自制的装置,诱导煤粉爆炸的激波由甲烷气体爆炸产生,对激波诱导下煤粉的爆炸压力Pmax、爆炸压力上升速率(dp/dt)max进行了实验研究。该实验分别研究煤粉浓度及煤粉粒度对爆炸指数的影响,其结果表明:对于不同的煤粉浓度,存在一个理想煤粉浓度值,在这个浓度下的煤粉爆炸压力值最大;随着煤粉粒度的减小,其爆炸压力不断升高。     

固体惰性介质对煤粉爆炸压力的影响研究

通过对固体惰性介质在减轻煤粉爆炸作用的实验研究,给出影响固体惰化剂作用效果的主要影响因素。实验分别选用来自加拿大和中国的3种煤粉和石灰石,对每种实验样品的成分、粒度都进行分析。用20L球形容器进行实验,测定煤粉中加入不同含量的石灰石后煤粉爆炸的Pmax和(dp/dt)max值。结果表明,石灰石能够起到减轻煤粉爆炸影响的作用,并且随着煤粉粒度的减小,要达到相同的抑爆效果需要的石灰石的用量将加大。     

Experimental study on CO2/CF3I suppression of methane-air explosion and flame propagation

To explore the inhibitory effects of CF₃I and CO₂ gas on the explosion pressure and flame propagation characteristics of 9.5% methane, a spherical 20 L experimental explosion device was used to study the effect of the gas explosion suppressants on the maximum explosion pressure, maximum explosion pressure rise rate and flame propagation speed of methane. The results indicated that with a gradual increase in the volume fraction of the gas explosion suppressant, the maximum explosion pressure of methane and maximum explosion pressure rise rate gradually decreased, and the time taken to reach the maximum explosion pressure and maximum explosion pressure rise rate was gradually delayed. At the same time, the flame propagation speed gradually decreased. Additionally, the time taken for the flame to reach the edge of the window and the time taken for a crack as well as a cellular structure to appear on the flame surface was gradually delayed. The fluid dynamics uncertainty was suppressed. The explosion pressure and flame propagation processes were markedly suppressed, but the flame buoyancy instability was gradually enhanced. By comparing the effects of the two gas explosion suppressants on the pressure and flame propagation characteristics, it was found that at the same volume fraction, trifluoroiodomethane was significantly better than carbon dioxide in suppressing the explosion of methane. By comparing the reduction rates of the characteristic methane explosion parameters at a volume fraction of 9.5%, it was observed that the inhibitory effect of 4% trifluoroiodomethane on the maximum explosion pressure was approximately 4.6 times that of the same amount of carbon dioxide, and the inhibitory effect of 4% trifluoroiodomethane on the maximum explosion pressure rise rate and flame propagation speed was approximately 2.7 times that of the same amount of carbon dioxide. The addition of 0.5%–1.5% trifluoromethane to 4% and 8% carbon dioxide can improve the explosion suppression efficiency of carbon dioxide. This enhancing phenomenon is a comprehensive manifestation of the oxygen-decreasing effect of carbon dioxide and the trifluoroiodomethane-related endothermic effect and reduction in key free radicals.     

Influences of coal dust components on the explosibility of hybrid mixtures of methane and coal dust

In order to study the influences of coal dust components on the explosibility of hybrid mixture of methane and coal dust, four kinds of coal dust with different components were selected in this study. Using the standard 20 L sphere, the maximum explosion pressure, explosion index and lower explosion limits of methane/coal dust mixtures were measured. The results show that the addition of methane to different kinds of coal dust can all clearly increase their maximum explosion pressure and explosion index and decrease their minimum explosion concentration. However, the increase in the maximum explosion pressure and explosion index is more significant for coal dust with lower volatile content, while the decrease in the minimum explosion concentration is more significant for coal dust with higher volatile content. It is concluded that the influence of methane on the explosion severity is more pronounced for coal dust with lower volatile content, but on ignition sensitivity it is more pronounced for coal dust with higher volatile content. Bartknecht model for predicting the lower explosion limits of methane/coal dust mixture has better applicability than Le Chatelier model and Jiang model. Especially, it is more suitable for hybrid mixtures of methane and high volatile coal dust.     

基于20L球形爆炸装置的甲烷煤尘混合爆炸实验

利用实验室自行设计的20L球形爆炸装置,对煤尘及甲烷煤尘混合物的爆炸特性进行了研究。结果表明:无论有无甲烷,煤尘的最大爆炸压力随煤尘浓度增加呈现先升高后降低的变化趋势,并且均在在煤尘浓度为600g/m3时均达到最大值。同时,甲烷的加入明显提高了煤尘最大爆炸压力值,而且随着甲烷浓度的增加,最大爆炸压力增幅先增加后降低,在甲烷5%时增幅最大。煤尘的爆炸持续时间随煤尘浓度增加呈现先降低后升高的特点,甲烷存在时有同样规律,但是有甲烷时爆炸持续时间明显降低,而且随着甲烷含量的增加,煤尘的爆炸持续时间降低幅度不断增加,在甲烷5%以后趋于稳定。实验结果对生产实践有一定的指导作用。     

湍流状态下甲烷爆炸特性的实验研究

利用20L近球形气体爆炸反应装置,测试甲烷在宏观静止和湍流两种不同状态下的爆炸特性。实验结果表明:甲烷的爆炸极限受其流动状态的影响不明显;湍流状态下甲烷爆炸压力Pm和爆炸压力上升速率(dp/dt)m较宏观静止状态明显增大,爆炸压力峰值时间tm明显缩短,其中爆炸压力上升速率受湍流影响较为显著;甲烷浓度不同,其爆炸受湍流影响的程度也不同,较高浓度(11%～16%)时的Pm受湍流的影响程度较大,越靠近最佳浓度(dp/dt)m和tm受湍流的影响程度越大;同一浓度下Pm和(dp/dt)m随着湍流的加强而增大,tm则缩短。该研究表明,避免和减少湍流对矿井瓦斯爆炸过程的抑制具有重要作用。     

Effects of obstacles and deposited coal dust on characteristics of premixed methane–air explosions in a long closed pipe

An experimental system including pressure transducer, electric spark ignition device, data acquisition and control unit was set up to investigate methane–air explosions in a horizontal pipe closed at both ends with or without the presence of obstacles and deposited coal dust. The experimental results show that explosion characteristics depended on the methane content, on the layout of obstacles, and on the deposited coal dust. Pressure fluctuation with a frequency of 150 Hz appeared in its crest when the methane content was close to the stoichiometric ratio (9.5% methane percentage by volume). The pressure rise rate increased locally when a single obstacle was mounted in the pipe, but it had little effect on the pressure peak. Repeated obstacles mounted in the pipe caused the pressure to rise sharply, and the mean maximum explosion overpressure increased with the increase of the obstacle’s number. The amplitude of pressure fluctuation was reduced when deposited coal dust was paved in the bottom of the pipe. However, when repeated obstacles were arranged inside, the maximum overpressures were higher with coal dust deposited than pure gas explosions.     

Comparison of explosion parameters for Methane–Air mixture in different cylindrical flameproof enclosures

Flameproof enclosures having internal electrical components are generally used in classified hazardous areas such as underground coalmines, refineries and places where explosive gas atmosphere may be formed. Flameproof enclosure can withstand the pressure developed during an internal explosion of an explosive mixture due to electrical arc, spark or hot surface of internal electrical components. The internal electrical component of a flameproof enclosure can form ignition source and also work as an obstacle in the explosion wave propagation. The ignition source position and obstacle in a flameproof enclosure have significant effect on explosion pressure development and rate of explosion pressure rise. To study this effect three cylindrical flameproof enclosures with different diameters and heights are chosen to perform the experiment. The explosive mixture used for the experiment is stoichiometric composition of methane in air at normal atmospheric pressure and temperature.It is observed that the development of maximum explosion pressure (P_max) and maximum rate of explosion pressure rise (dp/dt)_ex in a cylindrical flameproof enclosure are influenced by the position of ignition source, presence of internal metal or non-metal obstacles (component). The severity index, K_G is also calculated for the cylindrical enclosures and found that it is influenced by position of ignition source as well as blockage ratios (BR) of the obstacles in the enclosures.