Interlocks for first offenders: effective?

OBJECTIVE: Vehicle interlocks have been shown to effectively reduce the recidivism of multiple driving-while-impaired (DWI) offenders; however, the evidence for their effectiveness with first offenders has been mixed. Two Canadian studies found that the installation of an interlock reduced first DWI recidivism, but U.S. studies in West Virginia and California failed to find a significant reduction in recidivism for first DWI offenders in interlock programs. The objective of this study was to determine the extent to which such devices were effective with first offenders in New Mexico. METHODS: This study compared 1,461 first offenders, who installed interlocks in New Mexico between January 1, 2003, and December 1, 2005, with 17,562 first offenders convicted during the same period who did not install the units. Cox multivariate proportional hazards regression (CMVPHR) was used to compare recidivism rates during three periods: while the interlock was on the vehicles of offenders who installed them, after those offenders removed the units until the end of the study period (approximately 2 years), and for the combined period (both while the interlock was installed and after it was removed). RESULTS: While the device was on the vehicles of the interlock group, their recidivism rate, 2.6% per year of exposure, was significantly less than the 7.1% per year rate of the comparison group (CMVPHR hazard ratio = 0.39, p < 0.0001). After the device was removed, the annualized recidivism rate of the interlock group increased to 4.9% per year of exposure, which was less than the 6.7% rate of the comparison group, but the hazard ratio was not statistically significant (CMVPHR hazard ratio = 0.82, p = 0.16). When the combined periods (interlock on and off) were considered, the interlock group had a recidivism rate of 3.9% per year, which again was significantly lower than the 6.8% rate for the comparison group (CMVPHR hazard ratio = 0.61, p < 0.0001). CONCLUSION: The study provides evidence that interlocks are as effective with first offenders (approximately 60% reduction in recidivism when on the vehicle) as they are for multiple offenders. In addition, the benefits of requiring an interlock for first offenders exceed the costs by a factor of three.     

Testing of dust clouds for the electrostatic-spark ignition hazard in industry. Need for a modified approach?

Current standard test methods for electric-spark minimum ignition energies (MIEs) of dust clouds in air require that a series inductance of at least 1–2 mH be included in the electric-spark discharge circuit. The reason is to prolong the spark discharge duration and thus minimize the spark energy required for ignition. However, when assessing the minimum electrostatic energy ½CU² for dust cloud ignition by accidental electrostatic-spark discharges, current testing standards require that the series inductance of at least 1–2 mH be removed from the spark discharge circuit. No other changes of apparatus and test procedure are required. The present paper questions whether this simple approach is always adequate. The reason is that in practice in industry accidental electrostatic-spark discharge circuits may contain large ohmic resistances due to corrosion, poor electrical grounding connections, poorly electrically conducting construction materials etc. The result is increased spark discharge durations and reduced mechanical disturbance of the dust cloud by the blast wave emitted by the spark. Therefore, testing for minimum ½CU² for ignition by accidental electrostatic spark discharges may not only require removal of the series inductance of 1–2 mH from the standard MIE spark discharge circuit. Additional tests may be needed with one or more quite large series resistances R_s inserted into the spark discharge circuit. The present paper proposes a modified standard test procedure for measurement of the minimum electrostatic-spark ignition energy of dust clouds that accounts for these effects.     

Protective clothing for pesticide operators: part I – selection of a reference test chemical for penetration testing

A systematic approach was taken to develop a database for protective clothing for pesticide operators; results are reported as a two-part series. Part I describes the research studies that led to identification of a pesticide formulation that could serve as a reference test chemical for further testing. Measurement of pesticide penetration was conducted using different types of pesticide formulations. Six fabrics were tested using 10 formulations at different concentrations. Three formulations were subsequently selected for further testing. Analysis of the data indicated that, when compared with other formulations, mean percent penetration of 5% Prowl 3.3 EC [emulsifiable concentrate diluted to 5% active ingredient (pendimethalin)] is either similar to or higher than most test chemicals. Those results led to choosing 5% Prowl 3.3 EC as a reference test liquid. Part II of the study, published as a separate paper, includes data on a wide range of textile materials.     

Rotating biological contactors for wastewater treatment – A review

Rotating biological contactors (RBCs) for wastewater treatment began in the 1970s. Removal of organic matter has been targeted within organic loading rates of up to 120 g m⁻² d⁻¹ with an optimum at around 15 g m⁻² d⁻¹ for combined BOD and ammonia removal. Full nitrification is achievable under appropriate process conditions with oxidation rates of up to 6 g m⁻² d⁻¹ reported for municipal wastewater. The RBC process has been adapted for denitrification with reported removal rates of up to 14 g m⁻² d⁻¹ with nitrogen rich wastewaters. Different media types can be used to improve organic/nitrogen loading rates through selecting for different bacterial groups. The RBC has been applied with only limited success for enhanced biological phosphorus removal and attained up to 70% total phosphorus removal. Compared to other biofilm processes, RBCs had 35% lower energy costs than trickling filters but higher demand than wetland systems. However, the land footprint for the same treatment is lower than these alternatives. The RBC process has been used for removal of priority pollutants such as pharmaceuticals and personal care products. The RBC system has been shown to eliminate 99% of faecal coliforms and the majority of other wastewater pathogens. Novel RBC reactors include systems for energy generation such as algae, methane production and microbial fuel cells for direct current generation. Issues such as scale up remain challenging for the future application of RBC technology and topics such as phosphorus removal and denitrification still require further research. High volumetric removal rate, solids retention, low footprint, hydraulic residence times are characteristics of RBCs. The RBC is therefore an ideal candidate for hybrid processes for upgrading works maximising efficiency of existing infrastructure and minimising energy consumption for nutrient removal. This review will provide a link between disciplines and discuss recent developments in RBC research and comparison of recent process designs are provided (Section 2). The microbial features of the RBC biofilm are highlighted (Section 3) and topics such as biological nitrogen removal and priority pollutant remediation are discussed (Sections 4 Biological nutrient removal in RBCs, 5 Priority pollutant remediation in RBCs). Developments in kinetics and modelling are highlighted (Section 6) and future research themes are mentioned.     

Modeling thermal analysis for predicting thermal hazards relevant to transportation safety and runaway reaction for 2,2′-azobis(isobutyronitrile)

The pure decomposition behavior of 2,2′-azobis (isobutyronitrile) (AIBN) and its physical phase transformation were examined and discussed. The thermal decomposition of this self-reactive azo compound was explored using differential scanning calorimetry (DSC) to elucidate the stages in the progress of this chemical reaction. DSC was used to predict the kinetic and process safety parameters, such as self-accelerating decomposition temperature (SADT), time to maximum reaction rate under adiabatic conditions (TMR_ad), and apparent activation energy (E_a), under isothermal and adiabatic conditions with thermal analysis models. Moreover, vent sizing package 2 (VSP2) was applied to examine the runaway reaction combined with simulation and experiments for thermal hazard assessment of AIBN. A thorough understanding of this reaction process can identify AIBN as a hazardous and vulnerable chemical during upset situations. The sublimation and melting of AIBN near its apparent onset decomposition temperature contributed to the initial steps of the reaction and explained the exothermic attributes of the peaks observed in the calorimetric investigation.     

Shopping online for children: Is safety a consideration?

Introduction: There has been a significant increase in online purchasing and product safety problems have been identified in e-commerce. This study examines consumer behavior and safety perceptions among parents purchasing child products online. Method: A mixed methods approach, including focus groups and a survey with parents, identified key characteristics and behaviors. Cluster analysis was used to determine different population segments (including “Informed,” “Uninformed,” and “Infrequent” consumer groups) based on their frequency of online shopping and search for product information. “Safe” and “Unsafe” behavior groups were identified related to their search for safety information on child products. Logistic regression analysis was used to study the effects of consumer type groups and demographic variables on the chances of being a safer consumer. Results: Findings indicate that child product safety considerations are not a priority for parents when shopping online. Only 62% of the survey respondents indicated that they search for information prior to buying a child product online, of which only 13% of the respondents noted that they search for information on product safety. Risky consumer behaviors were identified including the purchase of imitation products (counterfeit or knockoff products) and autonomous checks for product safety in lieu of safety standards. The logistic regression analysis found that being an “Uninformed Consumer” increases the odds of an individual being an “Unsafe Consumer” by 8.4 times (χ²(11) = 97.33, p < .001). Practical Applications: Design of a social marketing campaign that targets these different population segments to change perceptions and promote safe online purchasing is recommended.     

Predicting vehicle belt fit for children ages 6–12

Objective: To predict shoulder belt fit and lap belt fit as a function of child age, vehicle seat characteristics, and belt geometry.

Methods: In a previous study, the lap belt and shoulder belt fit of 44 children aged 5–12 were measured in a simulated vehicle seat while varying cushion length, cushion angle, seatback angle, and belt anchorage geometry. A regression model was developed to predict lap belt fit and shoulder belt fit as a function of vehicle parameters and child stature. These regression models were applied to the stature distribution of 6- to 12-year-olds using a range of vehicle geometry data to predict the proportion of children expected to achieve good belt fit in the second-row, outboard seating positions of 46 vehicles when not using belt-positioning boosters.

Results: Across the ranges observed in vehicles, lap belt angle had the strongest effect on lap belt fit, although vehicle cushion length also contributed. Shoulder belt fit was most strongly affected by D-ring location. Vehicles with the geometric conditions most suitable for children are estimated to provide good lap belt fit for 25% of children aged 6 to 12. In 20% of vehicles, the shoulder belt is too far inboard for the target child population; 20% of vehicles are estimated to have shoulder belt fit too far outboard for children ages 6 to 12.

Conclusions: Based on this geometric analysis, the rear seats of most vehicles are unlikely to provide good lap belt fit for up to 75% of children ages 6–12. Shoulder belt fit is outside the target range for 40% of children. Consequently, children under 12 years of age are likely to experience markedly poorer belt fit when transitioning out of a booster seat.     

Amalgam in Dentistry A Health Hazard for Dental Personnel?

In a cross sectional study done in 1993 among dental personnel in Norrbotten, self-reported prevalence of muscular pain, headache, tremor, insomnia, irritation, impaired memory and depression, as well as information regarding different mercury exposures were collected Mercury exposures were determined as “number of amalgam fillings in teeth,” “years in practice,” “insufficient ventilation at work,” “total number of amalgam removed, produced and polished per day,” and “working in dental clinics.” As controls, physicians and nurses from the same geographical area were selected. The correlation between symptoms and different mercury exposures was calculated using logistic regression. The results suggested a higher prevalence of muscular fatigue and tremor for female dental personnel compared to controls Controls reported a lower prevalence of symptoms with increasing number of amalgam fillings in teeth. There was no correlation between the number of amalgam fillings handled per day and symptoms for dental personnel. Male dental personnel associated muscular fatigue headache, impaired memory, and depression with increased handling of amalgam in the clinic’ whereas the female dental personnel associated the same symptoms with the number of amalgam fillings in teeth. The strongest correlation was found between symptoms and insufficient ventilation at dental clinics for dental personnel.     

Preferred Handrail Height for Spiral Stairs—A Fitting Trial Study

Stairways are, in general, a thoroughly studied subject, but there is almost no scientific data available about spiral stairs. They are, however, widely used in homes, industrial sites and public buildings. The purpose of this study was to determine preferred handrail heights for a spiral stairway. The most preferred handrail height for descent was 105 cm. On the other hand, 95% of the participants regarded handrail heights between 95 and 100 cm satisfactory for descending. Participants’ anthropometric data was combined with the handrail height preference to develop a draft of a model to predict preferred handrail height for other user populations.     

Are cellular phone blocking applications effective for novice teen drivers?

ProblemDistracted driving is a significant concern for novice teen drivers. Although cellular phone bans are applied in many jurisdictions to restrict cellular phone use, teen drivers often report making calls and texts while driving.MethodThe Minnesota Teen Driver Study incorporated cellular phone blocking functions via a software application for 182 novice teen drivers in two treatment conditions. The first condition included 92 teens who ran a driver support application on a smartphone that also blocked phone usage. The second condition included 90 teens who ran the same application with phone blocking but which also reported back to parents about monitored risky behaviors (e.g., speeding). A third control group consisting of 92 novice teen drivers had the application and phone-based software installed on the phones to record cellular phone (but not block it) use while driving.ResultsThe two treatment groups made significantly fewer calls and texts per mile driven compared to the control group. The control group data also demonstrated a higher propensity to text while driving rather than making calls.DiscussionSoftware that blocks cellular phone use (except 911) while driving can be effective at mitigating calling and texting for novice teen drivers. However, subjective data indicates that some teens were motivated to find ways around the software, as well as to use another teen's phone while driving when they were unable to use theirs.Practical applicationsCellular phone bans for calling and texting are the first step to changing behaviors associated with texting and driving, particularly among novice teen drivers. Blocking software has the additional potential to reduce impulsive calling and texting while driving among novice teen drivers who might logically know the risks, but for whom it is difficult to ignore calling or texting while driving.     

Determination of explosion limits – Criterion for ignition under non-atmospheric conditions

Many industrial processes are run at non-atmospheric conditions (elevated temperatures and pressures, other oxidizers than air). To judge whether and if yes to what extent explosive gas(vapor)/air mixtures will occur or may be generated during malfunction it is necessary to know the safety characteristic data at the respective conditions. Safety characteristic data like explosion limits, are depending on pressure, temperature and the oxidizer. Most of the determination methods are standardized for ambient conditions. In order to obtain determination methods for non-atmospheric conditions, particularly for higher initial pressures, reliable ignition criteria were investigated. Ignition tests at the explosion limits were carried out for mixtures of methane, propane, n-butane, n-hexane, hydrogen, ammonia and acetone in air at initial pressures up to 20 bar. The tests have been evaluated according to different ignition criteria: visual flame propagation, temperature and pressure rising. It could be shown that flame propagation and occasionally self-sustained combustion for several seconds occurred together with remarkable temperature rise, although the pressure rise was below 3%. The results showed that the combination of a pressure rise criterion of 2% and a temperature rise criterion of 100 K seems to be a suitable ignition criterion for the determination of explosion limits and limiting oxidizer concentration at higher initial pressures and elevated temperatures. The tests were carried out within the framework of a R&D project founded by the German Ministry of Economics and Technology.     

A Parallel Graded-Mesh FDTD Algorithm for Human–Antenna Interaction Problems

The finite difference time domain method (FDTD) is frequently used for the numerical solution of a wide variety of electromagnetic (EM) problems and, among them, those concerning human exposure to EM fields. In many practical cases related to the assessment of occupational EM exposure, large simulation domains are modeled and high space resolution adopted, so that strong memory and central processing unit power requirements have to be satisfied. To better afford the computational effort, the use of parallel computing is a winning approach; alternatively, subgridding techniques are often implemented. However, the simultaneous use of subgridding schemes and parallel algorithms is very new. In this paper, an easy-to-implement and highly-efficient parallel graded-mesh (GM) FDTD scheme is proposed and applied to human–antenna interaction problems, demonstrating its appropriateness in dealing with complex occupational tasks and showing its capability to guarantee the advantages of a traditional subgridding technique without affecting the parallel FDTD performance.     

Safety assessment of potential supercritical solvents for Fischer–Tropsch Synthesis

Fischer–Tropsch Synthesis (FTS) is a primary pathway for gas-to-liquid (GTL) technology. In order to overcome commercial problems associated with reaction and transport phenomena, the use of supercritical solvents has been proposed to enhance conversion, catalyst stability and improve temperature control in fixed-bed reactors. One of the major challenges in designing the supercritical FTS reactor unit is selecting appropriate solvents of critical properties within the required reaction operating conditions. Numerous alternatives exist and should be screened based on relevant criteria. The main aim of this paper is to develop a screening methodology to identify an optimum supercritical solvent or a mixture of solvents that meet the aforementioned criteria while minimizing the cost and more importantly satisfying the safety constraints. A safety metric system was developed in order to compare the risk issues associated with using different solvents. In addition, an economic analysis of using the different solvents was performed. Finally, a case study was solved to illustrate the use of the proposed metrics and the selection of solvents based on safety and techno-economic criteria.     

Availability organisational analysis: Is it a hazard for safety?

This main issue of this article analyses the possible way to use for availability improvement, the organisational analysis methodology initially developed for accident safety investigations. As the last decade examples in the industrial world prove that some organisational weaknesses could either impact safety or availability, we have for purpose to make some important clarifications, with the help of the organisational paradigm, and grounded on our knowledge of safety accidents or local inquiries in hazardous technical complex systems.We will first give our definition of an availability event, by comparison with a safety event and recall what is for us an organisational analysis. Then we will consider the safety organisational paradigm pathogenic factors in wondering if these factors could also be seen as pathogenic factors for availability; or if specific availability pathogenic factors can be inferred from these safety pathogenic factors.In the end we will try to assess the common points and the differences between an availability oriented organisational analysis and a safety oriented one, with a particular attention to possible negative follows-up on safety issues and to the methodology issue.     

Algorithms for Increasing the Efficiency of Precision Production Operator’s Activities

To assess and plan future risk-analysis research projects, 275 documents describing methods and tools for assessing the risks associated with industrial machines or with other sectors such as the military, and the nuclear and aeronautics industries, etc., were collected. These documents were in the format of published books or papers, standards, technical guides and company procedures collected throughout industry. From the collected documents, 112 documents were selected for analysis; 108 methods applied or potentially applicable for assessing the risks associated with industrial machines were analyzed and classified. This paper presents the main quantitative results of the analysis of the methods and tools.     

Reuse of nickel recovered from spent Ni–Cd batteries for the preparation of C/Ni and C/Ni/Pd layered electrodes for energy sources

Nickel recovered in the recycling process of Ni–Cd batteries was used as a main component of bath for electrodeposition of nickel onto carbon fabric in order to obtain C/Ni composite. A part of the obtained composite was additionally coated with a thin layer of palladium (C/Ni/Pd composite). All the materials were investigated to assess the possibility of their use in the processes of electrochemical storage (sorption/desorption) of hydrogen and electrochemical oxidation of methanol. The obtained results showed the composites to be active electrode materials in these processes. The electrodes exhibited high activity and cyclability, especially in the process of methanol oxidation due to electrocatalytic activity of both nickel deposited onto carbon fabric and the outer layer of porous palladium coating nickel substrate.