煤巷掘进过程中粉尘浓度影响因素分析

为了掌握煤巷掘进过程中粉尘浓度变化的影响因素,根据气固两相流理论,针对矿井掘进工作面的特点,采用计算流体力学的离散相模型（DPM）考察了掘进巷道风速、风筒直径、风筒出风口到掘进工作面距离以及风筒的悬挂高度对粉尘浓度变化的影响。结果发现：当掘进巷道风速为0.25-4 m/s时,提高巷道内的通风风速,可以降低巷道内的粉尘浓度,缩短呼吸性粉尘浓度达到稳定的时间,减小工作面粉尘的危害;有利于通风除尘的风筒相关参数为风筒直径0.4-0.6 m、风筒出风口到掘进工作面距离6-7 m、风筒悬挂高度2.0-2.2 m。     

金属矿山掘进巷道新型通风除尘系统研究与应用

为了减少掘进巷道的粉尘危害,以某金属矿掘进工作面为研究对象,经过现场调研和理论分析,研究开发了1种适合掘进巷道的新型通风除尘系统。介绍了新型通风除尘系统的结构和工作原理,并将该通风除尘系统应用于掘进巷道的粉尘治理,对该系统在掘进巷道的应用效果进行现场测定。研究结果表明:该通风除尘系统将压风筒布置在巷道中心位置的顶部,抽风筒布置在巷道两侧的呼吸带高度,使得掘进工作面的风流位置控制在1.5 m之下,保障了作业人员的职业健康。系统的湿式除尘风机对掘进巷道粉尘除尘效率达到了91%以上,彻底解决了掘进巷道粉尘污染问题。同时该系统能够实现按需通风除尘,净化后的风流可以循环利用,节能效果显著,在金属矿山掘进巷道生产系统具有较好的应用前景。     

新型矿用湿式除尘器的研制与应用

在分析现有机械化掘进工作面除尘器结构特点和使用中所存在问题的基础上，经大量实验研制了适于井下掘进工作面的高效、实用的矿用湿式除尘器；通过对该种除尘器性能进行详细的实验研究，建立了除尘器性能的经验和半经验公式；确定了在掘进巷道中使用除尘器应采用长压短抽的通风方式。     

局部通风风筒直径的选择

应用局部通风提高掘进工作面空气质量是非常普遍的,局部通风的通风效果和经济性与风筒的选择密切相关.从风筒的购置费用、通过风筒局部通风消耗的电费及风筒日常的安装维护费用等最低经济条件下,定量分析了使用经济风筒直径在局部通风系统中的优点,并且得出了经济风筒直径计算式.通过实例验证了经济风筒直径计算式的正确性,获得了工作面所需风量与经济风筒直径的关系.在独头巷道的断面尺寸允许条件下,尽可能采用经济风筒直径进行局部通风,能降低通风能耗、提高风量,达到较好的通风效果.     

压入式局部通风倾斜巷道掘进工作面瓦斯分布规律

运用Fluent软件对压入式局部通风倾斜巷道掘进工作面瓦斯分布进行了模拟.比较了向上掘进和向下掘进巷道中瓦斯分布的不同;分析了风量对向上、向下倾斜掘进巷道中瓦斯分布的影响;研究了消除瓦斯高浓度区域向上、向下倾斜巷道所需风量的差别.结果表明:当条件相同,即风筒出口平均风速、倾斜角度和迎头瓦斯涌出量相同时,向上倾斜掘进工作面的高浓度瓦斯区域比向下倾斜时的高浓度瓦斯区域大;当回风流中瓦斯平均浓度不变时,随着风量和瓦斯涌出量的增加,由于风量的增加使到达迎头的风速变大,使空气和瓦斯混合得更加均匀,向上倾斜掘进工作面的高浓度瓦斯区域和向下倾斜的高浓度瓦斯区域之间的差距逐渐减小.消除高浓度瓦斯区域所需的风筒出口风量向上倾斜掘进巷道比向下倾斜掘进巷道大.     

新型矿用湿式除尘器的研制与应用

在分析现有机械化掘进工作面除尘器结构特点和使用中所存在问题的基础上，经大量实验研制了适于井下掘进工作面高效、实用的矿用湿式除尘器；对该种除尘器性能进行详细的实验研究，建立了除尘器性能的经验和半经验公式；确定了在掘进巷道中使用除尘器应采用长压短抽的能风方式。     

大断面掘进压入式风筒最佳高度的数值模拟

为了确定大断面掘进工作面压入式风筒的最佳安设高度,采用数值模拟方法分别模拟了风筒中心距底板6 m、4.5 m、3 m、2 m以及风筒安设于洞室顶部时,通风20 min后爆破炮烟(CO)的稀释效果,并求解了各种风筒布置情况下不同断面的通风死区比例。结果表明,通风排烟效果最差的情况为风筒固定于侧帮距底板6 m时,其次为风筒固定于侧帮距底板4.5 m时,再次为风筒固定于顶部中央时,风筒固定于侧帮距底板2 m时CO在巷道内的呼吸带高度沿程浓度分布与风筒距底板3 m时差别不大,但风筒中心距底板2 m时容易造成掘进工作面上隅角炮烟和粉尘的积聚。因此,大断面掘进工作面压入风筒最佳安设高度为3 m。     

风筒位置对掘进巷道流场影响的PIV实验*

为探究风筒位置对掘进巷道风流分布规律的影响,利用Fluent软件确定出实验模型内流体进入“第二自模区”的临界风速,保证实验模型与实际巷道的流动相似,采用粒子图像测速仪（PIV）对压、抽风筒距迎头不同距离下的前压后抽式通风流场进行测量。实验结果表明:抽风筒距巷道迎头距离的改变对迎头处流场影响较小,涡流中心位置也不会发生改变,当抽风筒距迎头距离大于4.5S,回流区的风流充分发展,流动较为平缓。压风筒距巷道迎头距离的改变对迎头处流场和涡流影响较大,当压风筒距迎头距离大于3S,涡流中心位置向远离迎头的方向移动,涡流区域逐渐扩大。基于相似理论的PIV实验结果可为矿井掘进巷道通风工作提供一定参考。     

大断面综掘巷道长压短抽条件下粉尘运移模拟

为改善大断面掘进巷道内通风除尘效果,针对龙王沟煤矿副斜井净断面积24.9 m2、供风量1 500 m3/min的情况,采用计算流体软件Fluent,建立长压短抽混合式通风条件下稳态离散相模型(DPM),研究压、抽风筒口相对位置和压抽风量配比对粉尘-风流耦合运移的影响。结果表明,当压入式风筒口到工作面距离为27.5 m,抽出式风筒口到工作面距离为5.0 m,压抽比为1.2时,龙王沟煤矿副斜井大断面综掘巷道内风流稳定,综合除尘效果最佳,模拟结果与现场实测结果基本一致。     

风筒出口位置对掘进工作面瓦斯分布的影响

根据计算流体动力学(CFD)理论,运用Fluent软件对掘进工作面的风流流场及瓦斯分布进行数值模拟,研究了在断面形状为梯形的掘进巷道中,瓦斯从掘进迎头和巷道两帮均匀涌出时,风筒出口离掘进迎头的距离对掘进巷道中风流流场和瓦斯分布的影响.结果表明: 压入式局部通风掘进巷道工作面风流从风筒出口流出后,沿风流方向瓦斯浓度逐渐增大,在靠近迎头处巷道两帮底部和顶部瓦斯浓度较高;随着瓦斯涌出量的增加,由于高浓度瓦斯密度降低而产生的上浮力的作用,在靠近迎头的上部区域发生瓦斯沿顶板逆风流方向流动的现象;上浮力的作用会改变流场的分布状况,在靠近迎头处产生涡流;风筒出口离掘进迎头越近,风流到达迎头时携带的瓦斯量越少,且迎头处的风速越大,靠近迎头区域中的瓦斯浓度越低.     

大尺寸通风管网中障碍物对瓦斯爆炸冲击波传播特性影响的数值模拟

为了研究大尺寸通风管网中的瓦斯爆炸传播规律,采用数值模拟方法,针对具有不同障碍物数量的大尺寸通风管网模型,利用Fluent分析管网中各个监测点的超压变化曲线以及障碍物附近的速度矢量图,分析爆炸冲击波传播规律。研究结果表明:初期瓦斯爆炸后,障碍物的存在改变了通风管网内未燃瓦斯的积聚区域;高温和高压发生耦合作用,在氧气相对充足的进气管道中形成二次爆炸;障碍物与火焰波以及管网自身结构变化等多种因素形成复合作用,改变了通风管网内瓦斯爆炸冲击波的传播路径和叠加区域的位置;无障碍物时高压区域出现在进气管道中,有障碍物时高压区域出现在中部直管与斜管的交汇处附近,且数值相对较大。     

表面处理对芳纶无纬布防弹性能的影响

本文对芳纶无纬布的表面处理进行了研究,对比了处理前后的面密度、表面光滑柔软性能、厚度、防水性能以及防弹性能。通过比较可知,经过表面处理后,芳纶无纬布不仅实现了防水功能,且其防弹性能没有下降。这说明,此处理方法可行,适合推广。     

U型工作面上隅角埋管瓦斯抽采数值模拟研究

传统的U型通风工作面上隅角瓦斯积聚现象经常出现，严重制约着矿井正常生产能力的有效发挥，对矿井安全生产造成重大威胁。基于前人对采空区非均质多孔介质气体运移理论的研究，采用Fluent软件数值模拟研究了U型和上隅角埋管条件下U型通风系统的静压力场和瓦斯浓度场。研究结果表明：在相同的模型参数条件下，U型通风容易造成上隅角瓦斯积聚，上隅角瓦斯超限问题十分严重；采空区5m处埋管，治理上隅角瓦斯积聚的效果欠佳，达不到安全开采的条件；15m处埋管可以较好的解决上隅角瓦斯超限问题，工作面没有出现瓦斯积聚现象，工作面和回风巷的瓦斯浓度始终处于1％以下；25m处埋管的效果与15m基本相同，没有表现出更好的瓦斯治理效果。综合数值模拟的结果，确定了上隅角埋管抽放采空区瓦斯的理想抽放位置为距离地板垂高1．2m、沿走向深入采空区15m处。     

Road characteristics and driver fatigue: a simulator study

Two experiments examined the influence of road characteristics on driver fatigue in a prolonged simulator drive. In experiment one, ten military truck drivers drove a mixed route, with straight, winding, and straight highway segments. In experiment two, 16 additional drivers drove either a straight, a winding, or a mixed route. Fatigue symptoms were assessed using performance, subjective, and psychophysiological measures (HRV). We hypothesized that drivers adopt different fatigue-coping strategies relative to the demands of the drive. Thus, on straight roads drivers are more likely to loosen their driving demands by either increasing their driving speed and/or not maintaining the lane position, as the road is tolerant to both strategies, whereas on winding roads, drivers are more likely to increase their speed but not their lane positioning. Our results confirm that decremental changes in driving performance varied among road types. In the straight road components, we found decrements in the quality of lane maintaining (experiment one) and steering quality (experiments one and two) and longitudinal speed (experiment two). In the winding road, we found that drivers increased their driving speed over time (experiments one and two).     

瓦斯爆炸在角联通风管网中的传播特性研究*

为研究真实通风工况下瓦斯爆炸冲击波在复杂管网内的超压演化规律及高温传播规律,采用数值模拟方法,研究角联通风管网模型中各个监测点在不同通风条件下对瓦斯爆炸冲击波超压及高温的影响规律,研究结果表明:瓦斯爆炸冲击波在角联管网传播过程中产生3个局部高压区域,高温气体主要在左、右通路内传播,斜角联分支内只受到微弱影响;管网入口风流的存在,使得爆炸初期冲击波超压经相同距离传播用时更短,峰值更大,破坏力更强;风流的存在使得管网内高温气体传播状态发生改变,斜角联分支与左通路尾部热量发生积聚,温度峰值更大。     

Adaptive response criteria in road hazard detection among older drivers

Objectives: The majority of existing investigations on attention, aging, and driving have focused on the negative impacts of age-related declines in attention on hazard detection and driver performance. However, driving skills and behavioral compensation may accommodate for the negative effects that age-related attentional decline places on driving performance. In this study, we examined an important question that had been largely neglected in the literature linking attention, aging, and driving: can top-down factors such as behavioral compensation, specifically adaptive response criteria, accommodate the negative impacts from age-related attention declines on hazard detection during driving?

Methods: In the experiment, we used the Drive Aware Task, a task combining the driving context with well-controlled laboratory procedures measuring attention. We compared younger (n = 16, age 21–30) and older (n = 21, age 65–79) drivers on their attentional processing of hazards in driving scenes, indexed by percentage of correct responses and reaction time of hazard detection, as well as sensitivity and response criteria using signal detection analysis.

Results: Older drivers, in general, were less accurate and slower on the task than younger drivers. However, results from this experiment revealed that older, but not younger, drivers adapted their response criteria when the traffic condition changed in the driving scenes. When there was more traffic in the driving scene, older drivers became more liberal in their responses, meaning that they were more likely to report that a driving hazard was detected.

Conclusions: Older drivers adopt compensatory strategies for hazard detection during driving. Our findings showed that, in the driving context, even at an older age our attentional functions are still adaptive according to environmental conditions. This leads to considerations on potential training methods to promote adaptive strategies that may help older drivers maintain performance in road hazard detection.     

抽出式通风煤巷掘进过程中粉尘浓度分布规律的数值模拟

根据气固两相流理论，针对矿井掘进工作面的特点，采用计算流体力学的离散相模型（DPM）对掘进工作面通风过程中粉尘浓度进行数值模拟，总结抽出式通风掘进巷道中粉尘浓度的沿程分布及变化规律。     

纳米混杂Kevlar／Surlyn复合材料的制备与防刺性能研究

本文介绍采用热压成型工艺制备纳米SiO2混杂Kevlar／Surlyn复合材料,研究了纳米粒子混杂工艺、纳米粒子含量对复合材料动态防刺性能的影响。结果表明,采用喷涂工艺制备的纳米SiO2混杂Kevlar／Surlyn复合材料可改善复合材料的防刺性能,其中纳米SiO2的含量为5wt．％时,复合材料的防刺效果最佳。     

Fatigued driver’s driving behavior and cognitive task performance: Effects of road environments and road environment changes

This study aims to explore the effects of different road environments and their changes on driving behaviors and cognitive task performance of fatigued drivers. Twenty-four participants volunteered in a 2 (road environment) × 3 (fatigue level) within-subjects factorial design simulated driving experiment. Participants were asked to perform basic numerical calculation and distance estimation of traffic signs when driving normally, and provide answers to a questionnaire on fatigue rating. Results show that fatigued drivers faced greater attention demand, were less alert, and tended to overestimate the distance to roadside traffic signs. Fatigue caused by driving in complex road environment had the greatest negative impact on driving behavior and visual distance estimation, and the fatigue transfer effect worsened significantly but differently on both driving behavior and performance of fatigued drivers when switching from a complex to a monotonous road environment and vice versa. Notably, this study shows that fatigued drivers performed relatively better in arithmetic tasks than non-fatigued ones. In addition, when switching from a monotonous to a complex road environment, drivers’ performance in visual distance estimation and arithmetic tasks improved though their driving behavior deteriorated, revealing that the fatigue effect upon drivers might be explained to some extent by their alertness and arousal levels.