Stabilization of heavy metals in MSWI fly ash using silica fume

The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR (²⁷Al and ²⁹Si) techniques. It was found that silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.     

Comparison of leaching characteristics of heavy metals in APC residue from an MSW incinerator using various extraction methods

This study investigates four extraction methods (water extraction, toxicity characteristics leaching procedure (TCLP), modified TCLP with pH control, and sequential chemical extraction (SCE)), each representing different liquid-to-solid (L/S) ratios, pH controls, and types of leachant, and their effects on the leaching concentration of heavy metals in municipal solid waste (MSW) incinerator air pollution control (APC) residue. The results indicated that for extraction with distilled water, the heavy metal leaching concentration (mg/l) decreased with L/S ratio, but the amount of heavy metal released (AHMR), defined as the leached amount of heavy metals to the weight of the tested sample (mg/kg), increased with an increase in L/S ratio, in the range of 2-100. The results also showed that both the leaching concentration and the amount of released metals were strongly pH-dependent in the TCLP and modified TCLP tests. In the case of pHs lower than 6.5, the leaching concentrations of Cd, Pb, Cu, Zn, and Cr decreased with an increase in pH. As pH increased higher than 6.5, Cr and Zn were almost insoluble. Meanwhile, Cd and Cu also showed a similar trend but at pHs of 8.5 and 7.5, respectively. Due to the nature of amphoteric elements, in the case of pHs higher than 7, the Pb leaching concentration increased with increasing pH. In modified TCLP tests with the pH value controlled at the same level as in the SCE test, the heavy metal speciation approached the extractable carbonate bound fraction by the SCE. Both amounts of targeted metals leached from the SCE and modified TCLP tests were much higher than those for the regular TCLP and water extraction tests.     

Heavy metal content of combustible municipal solid waste in Denmark.

Data on the heavy metal composition of outlets from Danish incinerators was used to estimate the concentration of Zn, Cu, Pb, Cr, Ni, Cd, As and Hg in combustible waste (wet as received) at 14 Danish incinerators, representing about 80% of the waste incinerated in Denmark. Zn (1020 mg kg(-1)), Cu (620 mg kg(-1)) and Pb (370 mg kg(-1)) showed the highest concentration, whereas Hg (0.6 mg kg(-1)) showed the lowest concentration. The variation among the incinerators was in most cases within a factor of two to three, except for Cr that in two cases showed unexplained high concentrations. The fact that the data represent many incinerators and, in several cases, observations from a period of 4 to 5 years provides a good statistical basis for evaluating the content of heavy metals in combustible Danish waste. Such data may be used for identifying incinerators receiving waste with high concentrations of heavy metals suggesting the introduction of source control, or, if repeated in time, the data must also be used for monitoring the impacts of national regulation controlling heavy metals. It is recommended that future investigations consider the use of sample digestion methods that ensure complete digestion in order to use the data for determining the total heavy metal content of waste.     

Evaluation of leaching and extraction procedures for soil and waste

Laboratory leaching tests may be used for source term determination as a basis for risk assessment for soil-groundwater pathways on contaminated sites. In order to evaluate different leaching procedures, batch extraction tests and percolation tests were performed using three reference materials produced from contaminated soil, demolition waste and municipal solid waste incinerator bottom ash. Emphasis was placed on the investigation of the leachability of the heavy metals copper and chromium, polycyclic aromatic hydrocarbons (PAHs) and the anions chloride and sulfate. Significant discrepancies between column experiments and batch/extraction tests were found for the release of PAHs and to a lesser extent for the heavy metals Cu and Cr. Additionally interlaboratory comparisons were conducted based on different leaching tests with the reference materials and evaluated using the criteria of comparability and reproducibility. The best reproducibility was achieved for all investigated substances in column tests. The reproducibility of batch tests was acceptable except for PAHs. The results from the experimental work will help establish standardized and feasible laboratory procedures as fundamental for substance specific risk assessment of contaminated sites.     

Assessment of benefits and risks of landfill materials for agriculture in Eritrea

In Eritrea, farmers have applied landfill materials as fertiliser to their fields for several decades. A sampling scheme in the landfill site of Asmara and selected farmers' fields was carried out to investigate the benefits and risks of using landfill materials for agriculture. Soil samples were collected from farmers' fields (7 samples) and from the Asmara landfill site (12 samples). The samples were analysed for major plant nutrients, heavy metals (Cd, Cr, Cu, Pb, Ni, Hg and Zn), and some physical properties. Nearly 65% (by weight) of the total landfill material mined from the landfill site constituted waste fractions of various substances. The remaining 35% was composed of soil-like materials, which are apparently used to fertilize agricultural soils. The average organic matter, total nitrogen, and available phosphorus contents of soils with landfill material measured 2.4%, 0.13%, and 45 mg kg(-1), respectively. However, soils without landfill material consisted of 1.1 % organic matter, 0.04% total N, and <40 mg kg(-1) of available P. Except for Hg, all the other heavy metals in the landfill site showed values above the permissible limits. In particular, the average concentrations of Cu (913 mg kg(-1)) and Pb (598 mg kg(-1)) in the landfill site were nine-fold and four-fold greater than the allowable limits, respectively. It is, therefore, suggested that composting fresh organic wastes should be considered and tested as an alternative material for fertilising agricultural soils and to maintain the quality of the environment.     

Heavy metal speciation in various types of fly ash from municipal solid waste incinerator

Fly ash (FA) from municipal solid waste incinerators has been known as hazardous waste, which is mostly because of the high content of heavy metal and dioxins. Besides the content, the form of the heavy metals in fly ash is also very important, because it is tightly related with the leaching behavior of fly ash in diverse circumstances. To evaluate the environment potential risk of fly ash, the Tessier chemical extraction method was adopted. In this study, four kinds of fly ash were examined, one sample from China (CFA) and the other three from Japan (RFA, CaFA and NaFA). Five metal elements were detected and they were Ni, Cr, Cd, Pb, and Cu. The result of total heavy metals’ concentration showed CFA has the lowest content. As to the Tessier chemical extraction experiments, the results show that Cd, Pb, and Cu have higher leaching risk in the environment than other heavy metals. The result of leaching test experiment showed that the more exchangeable speciation of Cd, Cr and Pb in FA, the more it could leach out in natural environment.     

Percolation and batch leaching tests to assess release of inorganic pollutants from municipal solid waste incinerator residues

In this study, percolation and batch leaching tests were considered in order to characterize the behaviour of air pollution control (APC) residues produced in a municipal solid waste incinerator (MSWI) as a function of the liquid to solid ratio (L/S). This waste is hazardous, and taking into account their physical and chemical properties, leaching of contaminants into the environment is the main concern. In our work the leaching behaviour of toxic heavy metals (Pb, Zn, Cr, Ni and Cu) and inorganics associated with soluble salts (Na, K, Ca and Cl) was addressed. Although pH of the leaching solution is the most important variable, L/S may also play an important role in leaching processes. In our work, results from column and batch tests were compared in terms of concentration (mg/L) and releasing (mg/kg). The APC residues revealed to be hazardous according to both tests, and both Pb and Cl⁻ far exceeded the regulatory thresholds. The material exhibits high solubility, and when the liquid to solid ratio was high, more than 50% can be solubilised. The patterns of release may be in some cases availability or solubility controlled, and the former was easier to identify. When the results from column and batch experiments were compared by representing the cumulative released amounts (in mg/kg) as a function of L/S, both curves match for Zn, Ni, Cu, K, Na, Cl and Ca, but for Cr and Pb a significant difference was observed. In fact, the column experiments revealed that under percolation conditions it should be expected slow releasing of Pb along time. From this study, it can be concluded that the released amounts obtained in batch experiments for a certain L/S should be considered as the worst case for medium term. Some simple models proposed on the literature and based on local equilibrium assumption showed good fitting to experimental data for soluble species (non-reactive solutes).     

膜分离—变压吸附耦合工艺处理催化剂载体生产废气

采用膜分离—变压吸附耦合工艺处理DQ催化剂载体生产过程产生的高浓度挥发性有机物（VOCs）废气。实验结果表明：在进气正己烷和非甲烷总烃的质量浓度分别为95 000~212 000 mg/m³和100 000 ~220 000 mg/m³、渗余侧压力0.25 MPa、渗透侧真空度0.09 MPa、进气流量15 Nm³/h的条件下,膜分离单元对废气中正己烷及非甲烷总烃的平均去除率分别为97.88%和97.29%;变压吸附单元对正己烷及非甲烷总烃的平均去除率分别为99.35%和99.33%;整套装置对正己烷及非甲烷总烃的平均总去除率分别为99.99%和99.98%。平均正己烷回收率达95.56%。处理后废气中非甲烷总烃质量浓度小于70 mg/ m³,达到北京市DB 11/ 447—2007 《炼油与石油化学工业大气污染物排放标准》的一级指标。     

Leaching of heavy metals from solidified waste using Portland cement and zeolite as a binder

This study investigated the properties of solidified waste using ordinary Portland cement (OPC) containing synthesized zeolite (SZ) and natural zeolite (NZ) as a binder. Natural and synthesized zeolites were used to partially replace the OPC at rates of 0%, 20%, and 40% by weight of the binder. Plating sludge was used as contaminated waste to replace the binder at rates of 40%, 50% and 60% by weight. A water to binder (w/b) ratio of 0.40 was used for all of the mixtures. The setting time and compressive strength of the solidified waste were investigated, while the leachability of the heavy metals was determined by TCLP. Additionally, XRD, XRF, and SEM were performed to investigate the fracture surface, while the pore size distribution was analyzed with MIP. The results indicated that the setting time of the binders marginally increased as the amount of SZ and NZ increased in the mix. The compressive strengths of the pastes containing 20 and 40wt.% of NZ were higher than those containing SZ. The compressive strengths at 28 days of the SZ solidified waste mixes were 1.2-31.1MPa and those of NZ solidified waste mixes were 26.0-62.4MPa as compared to 72.9MPa of the control mix at the same age. The quality of the solidified waste containing zeolites was better than that with OPC alone in terms of the effectiveness in reducing the leachability. The concentrations of heavy metals in the leachates were within the limits specified by the US EPA. SEM and MIP revealed that the replacement of Portland cement by zeolites increased the total porosity but decreased the average pore size and resulted in the better containment of heavy ions from the solidified waste.     

Enhancement of Sedimentation Velocity of Heavy Metals Loaded Hydroxyapatite Using Chitosan Extracted from Shrimp Waste

In this study, synthesize hydroxyapatite (HA) suspensions sedimentation was used after usual terms as support for adsorption of heavy metals ions. Thus, the effectiveness of chitosan, produced from shrimp waste, in the flocculation of turbid suspensions resulting from the treatment of water contaminated with heavy metals was studied by adsorption on HA. Different particles sizes of HA were mainly controlled in this work (an average of granule size ranging from 1.6 to 63 μm). The results of Cu²⁺ and Zn²⁺ adsorption on HA showed relatively fast kinetics, with removal extent of 88–95 % by varying the initial total metal concentration. High removal rates were obtained for Cu²⁺. Chitosan was found to be able to eliminate by flocculation more than 98 % of turbid suspensions generated by metals adsorption on HA after only 30 min of sedimentation. Effects of pH and dose of chitosan on the coagulation–flocculation process were also studied. The optimal dose of chitosan was found between 0.2 and 2 mg/L which corresponds to an optimal pH ranging from 6 to 7.     

What is left behind when the lights go off? Comparing the abundance and composition of litter in urban areas with different intensity of nightlife use in Mar del Plata,Argentina

Nightlife activities represents an important source of urban litter; the latter often being left behind or abandoned in public places and streets. Mar del Plata is a very important city on the Atlantic coast of Argentina and is the main tourism destination in the South Atlantic region of South America. However, few studies on urban litter related to nightlife activities have been conducted in the area. Here we assessed (i) the abundance and composition of litter, and (ii) the spatial and temporal variations of its abundance, diversity, richness and evenness in urbanized areas with different intensity of nightlife activities from April 2008 to March 2009. An overall of 13,503 items were counted. Around 92% of the total litter was comprised by cigarette butts, papers and plastics. We found significant spatial differences in the abundance of litter between sampling sites, with the greatest amounts of litter at the Alem site followed by the Hipólito site (both with an intensive nightlife activity) compared with the Chauvin site (a quiet high-income neighborhood). The composition of litter of the Alem and the Hipólito sites was relatively similar and both sites differ with respect to the Chauvin site. Cigarette butts, papers, and plastics were the items that contributed most to the dissimilarity between sampling sites. The diversity of litter was the single community parameter that significantly differed from the other seasons. We discussed the potential effect of nightlife activities on the amounts and quality of urban litter in the city of Mar del Plata.     

Biosorption study of potential fungi for copper remediation from Peninsular Malaysia

The ability to grow in heavy metal contaminated areas and absorb heavy metals from the environment make fungi a potentially viable biological‐based technology for remediating hazardous heavy metals in soil. In this study, 10 fungi from a copper (Cu)‐polluted area in Malaysia were isolated, with the four highest growth fungi identified as Simplicillium subtropicum, Fusarium solani, Aspergillus tamari, and Aspergillus niger. Results from toxicity and biosorption testing showed that A. niger and F. solani grew the fastest in the presence of Cu, but exhibited lower Cu uptake per unit of biomoass. In contrast, A. tamarii and S. subtropicum had lower growth rates, but showed better uptake of Cu per unit of biomass. S. subtropicum was identified as the best species for bioremediation because it had the highest Cu uptake and positive growth measured in the presence of Cu at concentrations below 100 mg/L. A niger proved to be most suitable for bioremediation if the concentration of Cu exceeds 100 mg/L.     

Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil

An attempted has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35–40%), acetylene (13–20%), ethylene (3–4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg^?1 and the concentrations of toxic gases, such as NO_x, HCl and HF, were below the regulatory emissions limit. Gas chromatography–mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 μm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding.     

催化氧化技术在橡胶废气处理中的应用

采用催化氧化技术处理热塑性丁苯橡胶( SBS)生产装置D线后处理单元废气,废气的非甲烷总烃去除率和环己烷去除率均达到98％以上,非甲烷总烃质量浓度达到DB11/447-2007《炼油与石油化学工业大气污染物排放标准》的要求(小于100 mg/m3).对SBS生产装置凝聚单元进行两釜流程改三釜流程后,催化氧化反应器入口非甲烷总烃质量浓度由( 3.84～5.82)×103 mg/m3降至( 2.48～2.63)×103 mg/m3,反应器出口非甲烷总烃质量浓度均小于50 mg/m3.凝聚单元改造并采用催化氧化技术处理废气后,每年节约费用约80万元.     

Metal leachability, heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in fly and bottom ashes of a medical waste incineration facility

Medical waste from hospitals and other healthcare institutions has become an imperative environmental and public safety problem. Medical waste in Greece has become one of the most urgent environmental problems, because there are 14,000 tons produced annually, of which only a small proportion is incinerated. In the prefecture of Attica there is only one modern municipal medical waste incinerator (started 2004) burning selected infectious hospital waste (5-6 tons day(-1)). Fly and bottom residues (ashes) are collected and stored temporarily in barrels. High values of metal leachability prohibit the landfilling of these ashes, as imposed by EU directives. In the present study we determined quantitatively the heavy metals and other elements in the fly and bottom ashes of the medical waste incinerator, by inductively coupled plasma emission spectrometry (ICP) and by energy dispersive X-ray analysis (EDAX). Heavy metals, which are very toxic, such as Pb, Cd, Ni, Cr, Cu and Zn were found in high concentrations in both fly and bottom ashes. Metal leachability of fly and bottom ashes by water and kerosene was measured by ICP and the results showed that toxic metals in both ashes, such as Pb, Cr, Cd, Cu and Zn, have high leaching values. These values indicate that metals can become soluble and mobile if ash is deposited in landfills, thus restricting their burial according to EU regulations. Analysis of polychlorinated biphenyls and polycyclic aromatic hydrocarbons in fly and bottom ashes showed that their concentrations were very low. This is the first known study in Greece and the results showed that incineration of medical waste can be very effective in minimizing the most hazardous and infectious health-care waste. The presence of toxic metals with high leachability values remains an important draw back of incineration of medical waste and various methods of treating these residues to diminish leaching are been considered at present to overcome this serious technical problem.     

柠檬酸淋洗去除电子垃圾污染土壤中的重金属

采用柠檬酸溶液对模拟电子垃圾污染土壤（简称污染土壤）中Cu,Pb,Cd 3种重金属进行淋洗实验,考察了柠檬酸溶液的浓度、柠檬酸溶液的pH、淋洗时间等对污染土壤中Cu,Pb,Cd的淋洗效果,探讨了柠檬酸溶液淋洗前后污染土壤中Cu,Pb,Cd 3种重金属各形态含量的变化。研究结果表明,在柠檬酸溶液的浓度0.100 mol/L、柠檬酸溶液的pH 5、淋洗时间1 440 min的适宜条件下,对污染土壤中Cu,Pb,Cd的去除率分别达到89.37%,72.11%,86.39%。柠檬酸溶液对3种重金属的去除主要是通过洗出酸可提取态（R1）和酸可还原态（R2）来实现的,每种重金属的R1和R2之和均占到其淋出总量的95%以上,而酸可氧化态（R3）和残渣态（R4）的含量淋洗前后基本无变化。     

Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost

The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.     

Correlation study of hazardous waste characteristics among various chemical processes in Republic of Korea

To harmonize with international standards, the Republic of Korea is in the process of converting its current hazardous waste classification system and setting up regulatory standards for all toxic substances present in hazardous waste. Detailed characterization of each form of hazardous waste belonging to five chemical processes and their correlations were studied. In the present work, the concentrations of 13 heavy metals, F^?, CN^?, 7 PAH compounds, total PCDD/F and 7 PCB isomers present in the hazardous waste generated among chemical processes such as synthetic rubber (SR), man-made fibers (MF), organic dyes and pigments (DP), pharmaceuticals and cosmetics were analyzed along with their leaching characteristics. Comparing all the processes, most of the heavy metal concentrations were high in SR waste. Naphthalene was the dominant PAH in most of the chemical process waste. PCDD/F concentrations of the samples were in the range of 0.001–0.003 ng I-TEQ/g. PCB isomer-101 and isomer-118 were found to be slightly higher than the permissible limit in the SR filter cake sample. SR process wastes doesn’t show any resemblance with the other process waste in either the heavy metals and PAH trend. Each sample from DP and MF were suitable only for hazardous waste landfill.     

Treatment of Sydney N.S. tar pond sludge in a pilot‐scale rotary kiln

Tar pond wastes from Sydney, Nova Scotia, containing 50 ppm or more of polychlorinated biphenyls (PCBs) were treated in a pilot‐scale rotary kiln. In order to use the existing feed system attached to the rotary kiln, the wastes were first oven‐dried. Stack gas sampling was conducted during the test, which included measurement of volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), semi‐volatile organic compounds (SVOCs), HCl, and metals. The purpose of this study was to determine emissions from treatment of the tar pond waste using rotary kiln technology. It was found that the dried sludge could sustain combustion in the kiln without any supporting fuel. The emissions of polychlorinated dibenzodioxins/furans (PCDD/Fs) were higher than the Canadian Council of Ministers of the Environment (CCME) air emissions guidelines, and the reasons for this are discussed. © 2008 Wiley Periodicals, Inc.     

Tank-connected food waste disposer systems – Current status and potential improvements

An unconventional system for separate collection of food waste was investigated through evaluation of three full-scale systems in the city of Malmö, Sweden. Ground food waste is led to a separate settling tank where food waste sludge is collected regularly with a tank-vehicle. These tank-connected systems can be seen as a promising method for separate collection of food waste from both households and restaurants. Ground food waste collected from these systems is rich in fat and has a high methane potential when compared to food waste collected in conventional bag systems. The content of heavy metals is low. The concentrations of N-tot and P-tot in sludge collected from sedimentation tanks were on average 46.2 and 3.9 g/kg TS, equalling an estimated 0.48 and 0.05 kg N-tot and P-tot respectively per year and household connected to the food waste disposer system. Detergents in low concentrations can result in increased degradation rates and biogas production, while higher concentrations can result in temporary inhibition of methane production. Concentrations of COD and fat in effluent from full-scale tanks reached an average of 1068 mg/l and 149 mg/l respectively over the five month long evaluation period. Hydrolysis of the ground material is initiated between sludge collection occasions (30 days). Older food waste sludge increases the degradation rate and the risks of fugitive emissions of methane from tanks between collection occasions. Increased particle size decreases hydrolysis rate and could thus decrease losses of carbon and nutrients in the sewerage system, but further studies in full-scale systems are needed to confirm this.