海上油田含油污泥对污泥-聚合物混合液性能的影响

为了回注处理海上油田含油污泥,将其与聚合物溶液混合,制备聚合物驱调剖体系。系统评价了含油污泥对污泥-聚合物混合液的溶液性能、使用性能及驱油效果的影响。实验结果表明:当含油污泥浓度小于300 mg/L时,油泥颗粒的粒径范围为0.1~100μm,d_(90)为40~60μm,污泥-聚合物混合液的黏度、抗剪切及抗老化稳定性均得到增强,注入性不受显著影响,阻力系数及残余阻力系数略有增加;当采用油泥浓度为100 mg/L的污泥-聚合物混合液进行驱油实验时,聚驱采收率增幅为7.26百分比,然而含油污泥浓度的进一步升高对提高采收率并不利。     

含酚废水的强化生化处理

喀山国立工业大学的В.Н .Шарифуллин等人对含有乙二醇、表面活性剂和酚的化工废水进行了强化生化处理研究 ,证明加入尿素可以加速酚的生物氧化。试验在曝气生物反应器中进行。废水的 p H为9.2 ,COD为 72 0 mg/L,乙二醇、表面活性剂和酚的质量浓度分别为 1 50 mg/L、7.4mg/L和 2 4 .8mg/L,活性污泥和氧的质量浓度分别为 4g/L和 4mg/L。尿素的加入量以 BOD5∶N∶P=1 0 0∶ 5∶ 1计。试验表明 ,废水经过 2 4 h生化处理后 ,如不加尿素 ,出水 p H为 9.0 ,COD为 1 1 0 mg/L,乙二醇、表面活性剂和酚的质量浓度分别为 0 .96mg/…     

长链烷烃降解菌C6的鉴定及性能研究

从含油活性污泥中筛选出一株长链烷烃降解菌C6,进行了菌种鉴定,考察了该菌对正十六烷及柴油和石蜡的混合物的降解能力,并对由菌株C6产生的生物表面活性剂进行了鉴定。实验结果表明:该菌为鲍曼不动杆菌(Acinetobacterbaumannii);对液体培养基中质量浓度为1 000 mg/L的正十六烷降解48 h后,降解率接近100%,降解动力学曲线的拟合结果符合Monod模型;对液体培养基中质量浓度为1 000 mg/L的柴油和石蜡的混合物降解96 h后,降解率达93%;菌株C6产生的生物表面活性剂经FTIR分析鉴定为磷脂类表面活性剂,排油圈直径为60 mm,临界胶束质量浓度约为25 mg/L,可将水的表面张力降至27.09 mN/m。     

内酯型槐糖脂修复石油污染土壤的影响因素

采用内酯型槐糖脂(SL50)修复石油污染土壤。通过单因子实验与正交实验,考察了槐糖脂溶液质量浓度、振荡时间、反应体系初始pH、NaCl加入量以及固液比(土壤质量与表面活性剂溶液体积之比)对污染土壤石油烃洗脱率的影响。单因子模型回归分析结果表明,参数变量均符合二次拟合模型,槐糖脂溶液质量浓度、反应体系初始pH以及NaCl加入量的二次模型拟合效果较好。正交实验结果表明,槐糖脂溶液质量浓度和反应体系初始pH是该实验的敏感性因子,最优洗脱条件为槐糖脂溶液质量浓度40 mg/L、反应体系初始pH 9、NaCl加入量6%(w)。     

有机硅改性破乳-絮凝剂在含油污水处理中的应用

采用破乳-絮凝法结合有机硅表面活性剂处理塔里木油田含油污水,以水样的油含量、Zeta电位、显微照片、界面张力为考察参数,得到一种新型水处理剂NP-22。NP-22为有机硅改性破乳-絮凝剂,其配方为破乳-絮凝剂YL-7和有机硅表面活性剂321的质量比95∶15。在NP-22加入量90 mg/L、反应温度45℃、沉降时间90min的优化条件下处理含油污水,水样的油含量由728.8 mg/L降至34.3 mg/L,除油率达95.3%。有机硅表面活性剂321可有效降低油水界面张力,与YL-7复合使用,可取得更好的除油效果。     

超临界水氧化法处理含油污泥

采用间歇式超临界水氧化(SCWO)反应器处理采油过程产生的含油污泥,考察了反应参数对污泥COD去除率的影响。实验结果表明,当初始COD为1 000 mg/L、反应温度为420℃、反应时间为10 min,反应压力为24 MPa、溶液pH为10、过氧比为400%时,SCWO法对含油污泥的COD去除率为92.20%,收集液COD低于GB8978—1996规定的一级排放标准(100 mg/L)。     

溴甲酚紫-十六烷基二甲基苄基溴化铵法测定废水中阴离子表面活性剂含量

采用溴甲酚紫-十六烷基二甲基苄基溴化铵法测定洗涤剂工业的生产废水或生活污水中阴离子表面活性剂的含量。实验表明:适合的溶液pH为8,测定波长λmax为588nm,在十六烷基二甲基苄基溴离子质量浓度为15.0mg/mL的条件下,十二烷基苯磺酸钠质量浓度在0—50μg/mL范围内符合比耳定律,其摩尔吸光系数为3.48×104L/(mol·cm),该方法的相对标准偏差小于4%,试样加标平均回收率为96%-102%。该法可用于测定工业废水、河流等环境水样中的阴离子表面活性剂含量。     

Fenton试剂—好氧活性污泥法处理邻苯二甲酸二丁酯废水

采用Fenton氧化—好氧活性污泥法处理邻苯二甲酸二丁酯(DBP)废水,优化了Fenton氧化反应的工艺条件。实验结果表明:在H_2O_2加入量4 g/L、Fe2+加入量200 mg/L、反应温度60℃、废水pH 4、反应时间60 min的最佳工艺条件下,Fenton氧化出水COD为200~250 mg/L,DBP质量浓度约为0.10 mg/L;在污泥质量浓度2 000 mg/L、DO 2~3 mg/L、水力停留时间8 h的条件下,好氧活性污泥法处理出水的COD基本低于50 mg/L,DBP质量浓度约为0.05 mg/L,均满足GB 8978—1996《污水综合排放标准》,可达标排放。     

Fenton试剂—好氧活性污泥法处理邻苯二甲酸二丁酯废水

采用Fenton氧化—好氧活性污泥法处理邻苯二甲酸二丁酯（DBP）废水,优化了Fenton氧化反应的工艺条件。实验结果表明：在H₂O₂加入量4 g/L、Fe²⁺加入量200 mg/L、反应温度60 ℃、废水pH 4、反应时间60 min的最佳工艺条件下,Fenton氧化出水COD为200~250 mg/L,DBP质量浓度约为0.10 mg/L;在污泥质量浓度2 000 mg/L、DO 2~3 mg/L、水力停留时间8 h的条件下,好氧活性污泥法处理出水的COD基本低于50 mg/L,DBP质量浓度约为0.05 mg/L,均满足GB 8978—1996《污水综合排放标准》,可达标排放。     

曝气强化非离子表面活性剂洗涤法修复柴油污染土壤

采用异位修复法,利用非离子表面活性剂洗涤柴油污染土壤,并在洗涤过程中曝气强化。考察了洗涤效果的影响因素,并通过表面张力和接触角的测定探讨了洗涤机理。实验结果表明:曝气对污染土壤中柴油的洗脱有强化作用,可提高洗脱率10%~20%;3种非离子表面活性剂的洗脱效果优劣次序为聚氧乙烯月桂醚(Brij-35)曲拉通X-100(TX-100)吐温-80(Tw-80);在表面活性剂浓度为1倍临界胶束浓度、曝气量为7.5 L/min、洗涤时间为60 min、洗涤液pH为11.0的优化条件下,Brij-35对柴油的洗脱率达77.4%,污染土样的含油率从7.0%降至1.6%,接触角从24.12°降至6.65°,可基本恢复土壤的亲水性;洗涤液的表面张力随表面活性剂浓度的增加而降低,但不受洗涤液pH的影响。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Selection of Autochthonous Plant Species from SE Spain for Soil Lead Phytoremediation Purposes

Mining activity in SE of Spain, in the west Mediterranean coast, originated more than two millenniums ago. It has generated huge areas affected by heavy metals contamination, especially of lead, which is possibly one of the most important. Investigations related to the selection of autochthonous plant taxa from a typical Spanish Mediterranean area, useful for phytoextraction and phytostabilization purposes in these polluted areas are shown. Under these edaphoclimatic conditions 12 interesting species were considered, from them six taxa were chosen for further studies. Some plant species have been proposed either for phytoextraction or phytostabilization purposes. Recommendations for further research have been discussed.     

Concentrations and Pools of Heavy Metals in Urban Soils in Stockholm,Sweden

The concentrations of heavy metals (Cd, Cr, Cu, Hg, Ni, Pb andZn) and arsenic (As) were surveyed and the metal pools estimatedin soils in Stockholm Municipality. The sampling sites were distributed all over the entire municipality with a higher sampling density in the city centre. Soils were sampled to a maximum depth of 25 to 60 cm. Soil texture, total-C content, electrical conductivity and pH were analysed. Heavy metal concentrations were determined after wet digestion with boiling7 M HNO₃.The results showed a wide range in heavy metal concentrations, as well as in other soil properties. The city centre soils constituted a rather homogeneous group whereas outside this areano geographical zones could be distinguished. These soils were grouped based on present land use, i.e. undisturbed soils, public parks, wasteland (mainly former industrial areas), and roadside soils. The city centre and wasteland soils generally hadenhanced heavy metal concentrations to at least 30 cm depth compared to park soils outside the city centre and rural (arable)soils in the region, which were used to estimate background levels. For example, the mean Hg concentration was 0.9 (max 3.3)mg kg^-1 soil at 0–5 cm and 1.0 (max 2.9) at 30 cm depth in the city centre soils, while the background level was 0,04 mg kg^-1. Corresponding values for Pb were 104 (max 444) and135 (max 339) mg kg^-1, at 0–5 and 30 cm, respectively, while the background level was 17 mg kg^-1.The average soil pools (0–30 cm depth) of Cu, Pb and Zn were 21,38 and 58 g m^-2 respectively, which for Pb was 3–4 timeshigher and for Cu and Zn 1.5–2 times higher than the backgroundlevel. The total amount of accumulated metals (down to 30 cm)in the city centre soils (4.5^*10 ⁶ m² public gardens and green areas) was estimated at 80, 1.1, 120 and 40 t for Cu, Hg, Pb and Zn, respectively. The study showed (1) thatfrom a metal contamination point of view, more homogeneous soilgroups were obtained based on present land use than on geographicdistance to the city centre, (2) the importance of establishing a background level in order to quantify the degree of contamination, and (3) soil samples has to be taken below the surface layer (and deeper than 30 cm) in order to quantify theaccumulated metal pools in urban soils.