Effect of Hybrid Tackifiers on Adhesion Properties of Epoxidized Natural Rubber-Based Pressure-Sensitive Adhesives

Viscosity, peel and shear strength of epoxidized natural rubber (ENR)-based pressure-sensitive adhesive was studied by using hybrid tackifiers consisting of a mixture of coumarone-indene resin and petro resin. The coumarone-indene resin concentration was fixed at 40 parts per hundred parts of rubber (phr). The concentration of petro resin, however, was varied from 20 to 80 phr. Toluene and polyethylene terephthalate (PET) film were used as the solvent and coating substrate respectively throughout the experiment. Viscosity of adhesive was determined by a HAAKE Rotary Viscometer whereas peel and shear strength was measured by a Lloyd Adhesion Tester. Results show that viscosity and shear strength decreases with increasing petro resin concentration. However, peel strength exhibits a maximum value at 40 phr petro resin, an observation which is attributed to maximum wettability and compatibility of adhesive on the substrate. ENR 25-based adhesive exhibits higher viscosity and peel strength but lower shear strength compared to the ENR 50 adhesive system.     

Material Properties and Influence of Molecular Weight and Testing Rate on Adhesion Properties of Epoxidized Natural Rubber-Based Adhesives

The effect of molecular weight and testing rate on peel and shear strength of epoxidized natural rubber (ENR-50)-based adhesive was investigated using petro resin as the tackifier. Toluene and polyethylene terephthalate were used as the solvent and substrate respectively. Peel and shear strength were determined by a Llyod Adhesion Tester operating at different rates of testing. Result shows that peel strength and shear strength increases up to an optimum molecular weight of 4.2 × 10⁴ g/mol of ENR-50. This observation is attributed to the combined effects of wettability and mechanical strength of rubber for peel strength. For shear strength, it is ascribed to the optimum cohesive and adhesive strength. Both peel strength and shear strength increases with increasing rate of testing, an observation which is associated to the viscoeslastic response of the adhesive. Thermal study, SEM and FTIR study confirms the miscibility of tackifier with ENR-50.     

Effect of Plasticizer Content on the Structure and Properties of SPI/MA-g-PBAT Blend Films

Journal of Polymers and the Environment - Soy protein isolate (SPI) has the advantages of low cost, easy processing, stable performance and so on. However, the processing temperature of SPI is...     

The Use of Interfacial Blend to Increase the Adhesion Properties of Natural Rubber/Polyvinylalcohol Multilayer Using Electron Beam Irradiation

Multilayers of natural rubber (NR) and polyvinylalcohol (PVA) were processed by casting natural rubber latex (NRL) then PVA with varying layer thickness. Adhesion between NR and PVA was found to be very poor, as determined with the peel method. The films of interfacial blend were composed of NRL and PVA having different ratios as a layer between NR/PVA layer, possessing good adhesion and exhibited one mechanical phase in tensile-elongation at break tests. The result of adhesion was confirmed by thermogravimetric analysis and scanning electron microscopy study. Also, adhesion was too strong for delamination at the interface when the unit of three layers NR/blend/PVA was irradiated at 25 kGy. To probe the effect of the adhesion difference on mechanical behavior and deformation of NR/blend/PVA layers at dry and wet conditions, the peel strength was examined as a function of layer thickness and aging time. The results indicated that the interfacial blend, irradiation process and film thickness were the key parameters affecting adhesion of NR/PVA layer.     

Effect of Manufacturing Process and Xanthan Gum Addition on the Properties of Cassava Starch Films

The objective of this work was to manufacture biodegradable films by two different processes (casting and extrusion), from different combinations of cassava starch and xanthan gum. These films were produced by casting and by extrusion from six different starch-xanthan gum combinations (0, 2, 4, 6, 8 and 10% w/w), containing glycerol as plasticizer (20% w/w) and were also characterized according to their microstructure, optical, mechanical, and barrier properties. Scanning electron microscopy of the starch-xanthan gum extruded films showed reticulated surface and smooth interior, suggesting that xanthan was driven to the surface and gelatinized starch to the interior of the films during extrusion. Films manufactured by casting were entirely homogeneous. In general, casted films presented lower opacity and water vapor permeability and higher stress at break than films manufactured by extrusion. Xanthan gum addition affected mechanical properties of starch films, improving their stress and strain at break, especially for extruded samples, but these properties did not show stability at different RH conditions.     

Effect of Common Chemical Treatments on the Process Kinetics and Mechanical Properties of Flax/Epoxy Composites Manufactured by Resin Infusion

Chemical treatments are widely employed to improve the fiber-matrix adhesion in composites based on eco-friendly fibers such as flax. To better understand the influence of these treatments on processing behavior, this study characterized the surface chemistry and morphology of woven flax fabrics treated by acetone, alkaline, silane and diluted epoxy. Flax/epoxy composites were then manufactured by resin infusion and the flow front and preform thickness evolution was monitored. The alkaline treatment was shown to result in a 50 % increase in equivalent permeability due to an increase in porosity which led to a decrease in flexural properties. The processing results were found to be in good agreement with predictions of a 1-dimensional model. This study suggests that infusion times are not considerably affected by the observed changes in surface energy. However, other implications of the treatments such as an increase in fibrillation can alter the infusion times significantly.

     

Study on the Effect of Dicumyl Peroxide on Structure and Properties of Poly(Lactic Acid)/Natural Rubber Blend

In attempt to enhance the compatibility of NR in PLA matrix, and furthermore to enhance mechanical properties of PLA, PLA/NR blends with strong interaction were prepared in Haake internal mixer, using dicumyl peroxide (DCP) as cross-linker. The effects of dicumyl peroxide on morphology, thermal properties, mechanical properties and rheological properties of PLA and PLA/NR blends were studied. The results indicated that dicumyl peroxide could increase the compatibility of poly(lactic acid) and natural rubber. With small amount of dicumyl peroxide, the effect on NR toughening PLA was enhanced and the tensile toughness of PLA/NR blends was improved. When the DCP content was up to 0.2 wt%, the PLA/NR blend reached the maximum elongation at break (26.21 %) which was 2.5 times of that of neat PLA (the elongation at break of neat PLA was 10.7 %). Meanwhile, with introducing 2 wt% DCP into PLA/NR blend, the maximum Charpy impact strength (7.36 kJ/m²) could be achieved which was 1.8 times of that of neat PLA (4.18 kJ/m²). Moreover, adding adequate amount of DCP could improve the processing properties of blends: the viscosity of PLA/NR blend decreased significantly and the lowest viscosity of the blends could be achieved when the DCP content was 0.5 wt%.     

The Effect of Silane Treated Fibre Loading on Mechanical Properties of Pineapple Leaf/Kenaf Fibre Filler Phenolic Composites

The aim of the present study is to investigate mechanical and morphological properties of pineapple leaf fibres (PALF) reinforced phenolic composites and its comparison with kenaf fibre (KF)/phenolic composites. Mechanical properties (tensile, flexural and impact) of untreated and treated PALF phenolic composites at different fibre loading were investigated. Tensile, flexural and impact properties of PALF and kenaf/phenolic composites were analyzed as per ASTM standard. Morphological analysis of tensile fracture samples of composites was carried out by scanning electron microscopy. Obtained results indicated that treated PALF/phenolic composites at 50% PALF loading exhibited better tensile, flexural and impact properties as compared to other untreated PALF/phenolic composites. Treated kenaf/phenolic composites at 50% fibre loading showed better tensile, flexural and impact properties than untreated kenaf/phenolic composite. It is concluded that treated 50% fibre loading kenaf and PALF/phenolic composites showed better mechanical properties than untreated kenaf and PALF/phenolic composites due to good fibre/matrix interfacial bonding. Results obtained in this study will be used for the further study on hybridization of PALF and KF based phenolic composites.     

Effect of Nucleating Agents on Physical Properties of Poly(lactic acid) and Its Blend with Natural Rubber

Poly(lactic acid) (PLA) presents high strength and modulus, but very low toughness as well as slow crystallization. Natural rubber (NR) was blended to enhance the toughness and nucleating agent was added to improve the crystallization. Cyclodextrin (CD), considered as a green compound, as well as calcium carbonate (CaCO₃) and talc were used as nucleating agents. Effects of these nucleating agents on crystallization, mechanical properties and morphology of neat PLA and PLA/NR blend were investigated. It was found that the addition of talc and CD decreased cold crystallization temperature (T_cc) of the PLA. Same result was obtained in PLA/NR blend containing talc. All nucleating agents increased the degree of crystallinity (Χ_C) of PLA, whereas only talc and CaCO₃ increased Χ_C of PLA in PLA/NR blends. The enhanced toughness of PLA by the addition of nucleating agent was attributed to its increased crystallinity, as well as decreased spherulite size. For PLA/NR blends, the increase in toughness was mainly contributed by the presence of the rubber.     

Effect of the Fe2O3/TiO2 Nanoparticles on the Structural,Mechanical, Electrical Properties and Antibacterial Activity of the Biodegradable Chitosan/Polyvinyl Alcohol Blend for Food Packaging

Journal of Polymers and the Environment - As the request for ready-made food grows, it’s more important than ever to develop effective antimicrobial food packaging materials to assure...     

Effects of Sodium Bisulfite on the Physicochemical and Adhesion Properties of Canola Protein Fractions

This study focused on investigating the potential of using canola protein fractions as bio-degradable wood adhesives. Native and sodium bisulfite (NaHSO₃)-modified canola protein fractions isolated successively at different pH values (7.0, 5.5, and 3.5) was used as adhesives. Wood specimens were assembled with adhesives at a pressure of 2?MPa at 150, 170, or 190?°C for 10?min. The adhesion performance of adhesives were evaluated by wet, soak, and dry shear strength. Their physicochemical properties: extractability, electrophoresis profiles, thermal, rheological and morphological properties were also characterized. Results showed that canola protein had the highest protein yield and purity at pH 5.5. Electrophoresis profile proved that NaHSO₃ cleaved the disulfide bonds in canola protein. This could induce extra charges (RS-SO₃ ^?) on the protein surface, leading to the reduced apparent viscosity. Thermal analysis implied that the thermal transition temperature of canola protein decreased with modification of NaHSO₃. Canola protein adhesives showed excellent dry and soak shear strength with 100?% wood cohesive failure in all curing temperatures. The wet adhesion strength of native and modified canola protein fraction adhesives at pH 5.5 and pH 3.5 (3.9?C4.1?MPa) was higher than the fractions at pH 7.0. NaHSO₃ had insignificant effects on the adhesion performance of canola protein adhesives but notably improved the handling and flow-ability properties of canola protein adhesives.     

Blending of Epoxidised Palm Oil with Epoxy Resin: The Effect on Morphology, Thermal and Mechanical Properties

Epoxy resin prepared by the reaction of a diglycidyl ether of bisphenol A (DGEBA) and m-xylylenediamine (m-XDA) was modified with 10% wt of epoxidized palm oil (EPO). The EPO was first pre-polymerized with m-XDA at various temperatures and reaction times. The resulting product was then mixed with the epoxy resin at 40?°C and allowed to react at 120?°C for another 3?h. The fully reacted DGEBA/m-XDA/EPO blend was characterized by using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal gravimetric analysis, tensile test, hardness indentation and dynamic mechanical analysis. The SEM study shows that different types of morphology, ranging from phase separated to miscible blends were obtained. A miscible blend was obtained when the m-XDA and EPO were reacted for more than 2?h. The results from DSC analysis show that the incorporation of EPO at 10% wt in the epoxy blend reduced the glass transition temperature (T _g). The lowered T _g and mechanical properties of the modified epoxy resins are caused by a reduction in crosslinking density and plasticizer effect.     

An Investigation into the Influence of C. moschata Leaves Extract on Physicochemical and Biological Properties of Biodegradable PCL/PLA Blend Film

Journal of Polymers and the Environment - Poly ε-caprolactone (PCL) synthesized by ring-opening polymerization method, and then it blended with polylactic acid (PLA). The blend was loaded with...     

Effect of Orientation on the Morphology and Mechanical Properties of PLA/Starch Composite Filaments

Polylactic acid (PLA)/starch fibers were produced by twin screw extrusion of PLA with granular or gelatinized starch/glycerol followed by drawing through a set of winders with an intermediate oven. At 30% starch, fibers drawn 2–5x were highly flexible (elongation 20–100%) while undrawn filaments were brittle (elongation 2–9%). Tensile strength and moduli increased with increasing draw ratio but decreased with increasing starch content. Mechanical properties were better for composites made with gelatinized starch/glycerol than granular starch. In conclusion, orientation greatly increases the flexibility of PLA/starch composites and this may be useful not only in fibers but also possibly in molded articles. Other advantages of starch addition could include fiber softness without added plasticizer, moisture/odor absorbency and as a carrier for active compounds.     

Effect of Coconut, Sisal and Jute Fibers on the Properties of Starch/Gluten/Glycerol Matrix

Coconut, sisal and jute fibers were added as reinforcement materials in a biodegradable polymer matrix comprised of starch/gluten/glycerol. The content of fibers used in the composites varied from 5% to 30% by weight of the total polymers (starch and gluten). Materials were processed in a Haake torque rheometer (120 °C, 50 rpm) for 6 min. The mixtures obtained were molded by heat compression and further characterized. Addition of lignocellulosic fibers in the matrix decreased the water absorption at equilibrium. The diffusion coefficient decreased sharply around 5% fiber concentration, and further fiber additions caused only small variations. The thermogravimetric (TG) analysis revealed improved thermal stability of matrix upon addition of fibers. The Young’s modulus and ultimate tensile strength increased with fiber content in the matrix. The storage modulus increased with increasing fiber content, whereas tanδ curves decreased, confirming the reinforcing effect of the fibers. Morphology of the composites analyzed under the scanning electron microscope (SEM) exhibited good interfacial adhesion between the matrix and the added fibers. Matrix degraded rapidly in compost, and addition of increased amounts of coconut fiber in the matrix caused a slowdown the biodegradability of the matrix. Names are necessary to report factually on available data; however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the product to the exclusion of others that may be suitable.     

The Effect of Natural Tree Gum and Environmental Condition on the Degradation of a Typical Automotive Clear Coat

In this work the effects of natural gum and its simulated compound (Arabic gum) on an acrylic based clear coat applied on different basecoats were studied. The experiments were conducted at various aging processes to simulate the real outdoor conditions by the aid of different analytical techniques including optical microscopy, scanning electron microscopy, ATR-FTIR spectroscopy, DMTA and micro hardness measurements, by which the chemical and mechanical responses of the system were investigated. Results showed that, Arabic and natural gums, due to their sticky nature in the slurry state, can strongly attach to the clear coat surface and perform a significant stress during the drying process. It was shown that, this stress was responsible for the surface cracks produced by gums, indicating a physical degradation mechanism. However, it was revealed that, biological materials could also affect the clear coat chemically. In addition, different surface cracks produced by gums on the clear coat applied on silver and black basecoats were observed and attributed to their surface chemistry and mechanical properties differences. It was shown that different amounts of aluminum flakes existed in the basecoat layers of silver and black system can effectively influence the curing degree of the clear coats applied on the se systems. This leads to different cross-linking density, toughness and surface chemistries. Therefore, different interactions of clear coats and gums, as well as stress distribution and relaxation behaviors of these two systems were found effective in such degradations. Comparison of the mechanical properties and visual effects of gums on clear coats indicated a more severe degradation under the post aging, due to the greater effect of UV light.     

Rheological and Thermal Properties of the PLA Modified by Electron Beam Irradiation in the Presence of Functional Monomer

Polylactic acid (PLA) has been modified by electron beam radiation in the presence of glycidyl methacrylate (GMA) to enhance the melt strength of PLA. The modified PLA was prepared by varying both the amount of GMA and the irradiation dose and was characterized by observing the thermal properties, the melt viscoelastic properties and the gel fraction. For comparison, virgin PLA was also irradiated. All irradiated virgin PLA had a lower complex viscosity and a storage modulus compared to virgin PLA due to irradiation-induced chain scission. However, these properties were remarkably improved due to formation of long chain branching and retarding chain scission if GMA was introduced in this system. The increase in melt viscoelastic property was much dependent on the irradiation dose. At optimum doses of radiation, it showed maximum complex viscosity and storage modulus. The PLA irradiated with 20 kGy in the presence of 3 phr GMA showed a complex viscosity of about 10 times higher and a storage modulus of 100 times higher than those of virgin PLA at 0.1 rad/s. Gel fraction measurement revealed that chain scission and branching was more dominant than crosslinking. The biodegradability of irradiated PLA was slightly decreased by the presence of GMA.     

Effect of Sugar Palm Fiber (SPF) to the Structural and Optical Properties of Bioplastics (SPF/Starch/Chitosan/Polypropylene) in supporting Mechanical Properties and Degradation Performance

Journal of Polymers and the Environment - Recycling plastic waste by mix with natural polymers for bio-plastic packaging produces plastics with high mechanical properties and easily degradable. In...     

Effect of Ionizing Radiation on the Morphological,Thermal and Mechanical Properties of Polyvinyl Alcohol/Polyethylene Glycol Blends

Blends of water—soluble polymers based on Poly vinyl alcohol (PVA) and Polyethylene glycol (PEG) have been prepared by the solution casting technique. The effect of various doses of γ-radiation on the structural properties of PVA/PEG polymer blends with all its compositions has been investigated. From the visual observation of all the blend compositions, it was found that, the best compatibility of the blend is up to 40% PVA/60%PEG. The structure–Property behavior of all the prepared blends before and after γ-irradiation was investigated by IR Spectroscopy, thermogravimetric analysis (TGA), mechanical properties and Scanning electron microscope (SEM). The gel content and the swelling behavior of the PVA/PEG blends were investigated. It was found that the gel content increases with increasing irradiation dose and PVA concentration in the blend. Swelling percent increased as the composition of PEG increased in the blend. The results obtained by FTIR analysis and SEM confirm the existence of possible interaction between PVA and PEG homopolymers. TGA of PVA/PEG blend, before and after γ-irradiation, showed that the unirradiated and irradiated PVA/PEG blends are more stable against thermal decomposition than pure PVA. Improvement in tensile mechanical properties of PVA/PEG blends was occurred.