Hydroreforming over Ni/H-beta of the thermal cracking products of LDPE, HDPE and PP for fuel production

The thermal cracking at 400?°C of pure polyolefins—low density polyethylene (LDPE), high density polyethylene (HDPE) and polypropylene (PP) and a standard polyolefin mixture (46?% LDPE?+?27?% HDPE?+?28?% PP)—was studied together with the catalytic hydroreforming of the obtained oils over Ni/h-beta at 310?°C under 20?bar of hydrogen. The oils obtained after the thermal cracking of PP contain the highest amount of gasoline (58?%), while those coming from HDPE the lowest (39?%). The bromine index of the oils was very high, ranging from 54.1 (LDPE) to 83.8 (PP), indicating a high olefinic content of the oils. Additionally, the thermal cracking of the mixture indicates the occurrence of a synergestic effect among plastics, with transfer of methyl groups from PP to polyethylenes. Ni/h-beta (Si/Al?=?25; Ni content?=?6.2?wt%) catalyst was used in the hydroreforming since it contains a bimodal pore size distribution (0.6/3.1?nm), which improves accessibility of the oil molecules to the catalytic sites. After the hydroreforming and regardless of the plastics used, the share of lighter products (gasoline and gases) increases, reaching a remarkable 68?% of gasolines with the oils coming from PP. Regardless of the starting feed, the amount of useful fuels (gasoline?+?light diesel) was within 80–85?%. Additionally, the oils were successfully hydrogenated since the bromine indexes dropped below 7, indicating that more than 90?% of the starting olefins were saturated. The usage of catalysts increased the amount of aromatics in the obtained oils within 13–20?%, depending on the starting plastic. Likewise, the isoparaffin content of the gasolines was within 35–40?%, except for PP, where it was enhanced to 62?%. However, the research octane number (RON) of the gasolines from LDPE and PP and the cetane indexes of the diesel from all the plastics were promising for their application as fuels.     

Conversion of LDPE into transportation fuels by a two-stage process using Ni/Al-SBA-15 as catalyst

Ni/Al-SBA-15 catalysts with Si/Al atomic ratios within the 20–135 range were prepared by a post synthesis grafting procedure, having nickel contents between 6 and 11 %. The addition of Ni to the Al-SBA-15 support caused a decrease of the BET surface area and pore volume. Additionally, larger Ni particles were attained over the catalysts with higher Si/Al atomic ratios, indicating the existence of some interaction between aluminium species and nickel particles. Ni/Al-SBA-15 catalysts displayed remarkable properties for the preparation of diesel fuels in the hydroreforming of the oils obtained from the LDPE thermal cracking. On increasing the Si/Al atomic ratios of the Ni/Al-SBA-15 catalysts, higher share of light and heavy diesel were attained, the sum reaching a maximum (67.3 %) for Ni/Al-SBA-15(70). This was caused by the higher extent of oligomerization reactions on enhancing the Si/Al atomic ratio. Additionally, around 85–90 % of the starting olefins were successfully hydrogenated and the aromatic content was rather low (below 5 %), without almost any polyaromatic compound (<0.1 %).     

Thermo-chemical extraction of fuel oil from waste lubricating grease

This study investigated the recovery of oil from waste grease through the process of thermal degradation in an aqueous solution of potassium hydroxide (KOH) followed by solvent extraction. Waste high temperature metal bearing grease was dissolved in a 15 w/w% KOH solution at 80 °C while being agitated at 2000 rpm using a shear action agitator for a period of 15 min. Two distinct layers were observed after 8 min of settling time. The top layer being of dark brown oil and the bottom layer was a heterogeneous mixture. The two layers were separated by decantation. The bottom layer was cooled down to 45 °C followed by slow addition of toluene (C₇H₈) while agitating at 1200 rpm for 15 min to prevent solids settling and minimise rapid volatilisation of the organic compounds in the mixture. Two distinct layers were also formed, the top homogeneous mixture of light brown oil–toluene mixture and the bottom sludge layer. The solvent was recovered from the oil for re-use by fractional distillation of the homogenous mixture. It was observed that 15 w/w% potassium hydroxide solution can chemically degrade the soap matrix in the grease and extract up to 49 w/w% of the fuel oil when subjected to high shear stress at a temperature of 80 °C. The 26 w/w% extraction of oil in the remaining sludge was obtained by solvent extraction process with mass ratios of sludge to solvent of 2:1. Solvent recovery of 88% by mass was obtained via fractional distillation method. The combined extraction processes brought an overall oil yield of 75 w/w% from the waste grease. The fuel oil obtained from this process has similar properties to paraffin oil and can be blended with other oils as an alternative energy source.     

Simultaneous recovery of vanadium and nickel from power plant fly-ash: Optimization of parameters using response surface methodology

Simultaneous recovery of vanadium (V) and nickel (Ni), which are classified as two of the most hazardous metal species from power plant heavy fuel fly-ash, was studied using a hydrometallurgical process consisting of acid leaching using sulfuric acid. Leaching parameters were investigated and optimized in order to maximize the recovery of both vanadium and nickel. The independent leaching parameters investigated were liquid to solid ratio (S/L) (5–12.5 wt.%), temperature (45–80 °C), sulfuric acid concentration (5–25 v/v%) and leaching time (1–5 h). Response surface methodology (RSM) was used to optimize the process parameters. The most effective parameter on the recovery of both elements was found to be temperature and the least effective was time for V and acid concentration for Ni. Based on the results, optimum condition for metals recovery (actual recovery of ca.94% for V and 81% for Ni) was determined to be solid to liquid ratio of 9.15 wt.%, temperature of 80 °C, sulfuric acid concentration of 19.47 v/v% and leaching time of 2 h. The maximum V and Ni predicted recovery of 91.34% and 80.26% was achieved.     

Thermal processing of paper sludge and characterisation of its pyrolysis products

Paper sludge is a waste product from the paper and pulp manufacturing industry that is generally disposed of in landfills. Pyrolysis of paper sludge can potentially provide an option for managing this waste by thermal conversion to higher calorific value fuels, bio-gas, bio-oils and charcoal. This work investigates the properties of paper sludge during pyrolysis and energy required to perform thermal conversion. The products of paper sludge pyrolysis were also investigated to determine their properties and potential energy value. The dominant volatile species of paper sludge pyrolysis at 10 °C/min were found to be CO and CO₂, contributing to almost 25% of the paper sludge dry weight loss at 500 °C. The hydrocarbons (CH₄, C₂H₄, C₂H₆) and hydrogen contributed to only 1% of the total weight loss. The bio-oils collected at 500 °C were primarily comprised of organic acids with the major contribution being linoleic acid, 2,4-decadienal acid and oleic acid. The high acidic content indicates that in order to convert the paper sludge bio-oil to bio-diesel or petrochemicals, further upgrading would be necessary. The charcoal produced at 500 °C had a calorific value of 13.3 MJ/kg.     

Leaching behavior of copper from waste printed circuit boards with Brønsted acidic ionic liquid

In this work, a Brønsted acidic ionic liquid, 1-butyl-3-methyl-imidazolium hydrogen sulfate ([bmim]HSO₄), was used to leach copper from waste printed circuit boards (WPCBs, mounted with electronic components) for the first time, and the leaching behavior of copper was discussed in detail. The results showed that after the pre-treatment, the metal distributions were different with the particle size: Cu, Zn and Al increased with the increasing particle size; while Ni, Sn and Pb were in the contrary. And the particle size has significant influence on copper leaching rate. Copper leaching rate was higher than 99%, almost 100%, when 1 g WPCBs powder was leached under the optimum conditions: particle size of 0.1–0.25 mm, 25 mL 80% (v/v) ionic liquid, 10 mL 30% hydrogen peroxide, solid/liquid ratio of 1/25, 70 °C and 2 h. Copper leaching by [bmim]HSO₄ can be modeled with the shrinking core model, controlled by diffusion through a solid product layer, and the kinetic apparent activation energy has been calculated to be 25.36 kJ/mol.     

Temperature-dependent pyrolytic product evolution profile for low-density polyethylene from gas chromatographic study

In this work, a product distribution study from thermal degradation of low-density polyethylene (LDPE) is presented. Thermal degradation of the polymer was investigated under dynamic condition in an inert environment using a thermo-gravimetric analyzer (TGA) coupled with evolved products’ analysis using a gas chromatograph (GC). Fractions evolved at nine different temperatures from 200 to 600 °C were injected into GC for a detailed product analysis. The main objective of the present investigation is to highlight the species-specific evolution profiles of LDPE pyrolyzates (C5–C44) at different stages of its degradation under an inert environment. Pyrograms have been analyzed in terms of amount of different products evolved at various pyrolysis temperatures. Volatile pyrolyzates essentially remain low at low decomposition temperature (200–300 °C) of the polymer, which gradually increase to attain a maximum at maximum decomposition temperature (470 °C) and finally level off at 600 °C. In the mechanistic approach adopted to understand the decomposition mechanism of LDPE, the following reaction types were considered: (a) main chain cleavage to form chain-terminus radicals; (b) intramolecular hydrogen transfer to generate internal radicals; (c) intermolecular hydrogen transfer to form both volatile products and radicals; and (d) β-scission to form both volatiles and terminally unsaturated polymer.     

Physico-chemical and biological treatment of MSW landfill leachate

This paper analyses the evolution of the physico-chemical characteristics of the leachate from the Central Landfill of Asturias (Spain), which has been operating since 1986, as well as different treatment options. The organic pollutant load of the leachate, expressed as chemical oxygen demand (COD), reached maximum values during the first year of operation of the landfill (around 80,000 mg/L), gradually decreasing over subsequent years to less than 5000 mg/L. The concentration of ammonium, however, has not decreased, presenting values of up to 2000 mg/L. When feasible, recirculation can greatly decrease the organic matter content of the leachate to values of 1500–1600 mg COD/L. Applying anaerobic treatment to leachates with a COD between 11,000 and 16,000 mg/L, removal efficiencies of 80–88% were obtained for organic loading rates of 7 kg COD/m³ d. For leachates with lower COD (4000–6000 mg/L), the efficiency decreased to around 60% for organic loading rates of 1 kg COD/m³ d.Applying coagulation–flocculation with iron trichloride or with aluminium polychloride, it was possible to reduce the non-biodegradable organic matter by 73–62% when treating old landfill leachate (COD: 4800 mg/L, BOD₅: 670 mg/L), also reducing turbidity and colour by more than 97%. It is likewise possible to reduce the non-biodegradable organic matter that remains after biological treatment by adsorption with activated carbon, although adsorption capacities are usually low (from 15 to 150 mg COD/g adsorbent). As regards ammonium nitrogen, this can be reduced to final effluent values of 5 mg/L by means of nitrification/denitrification and to values of 126 mg/L by stripping at pH 12 and 48 h of stirring.     

Mesophilic and thermophilic anaerobic biodegradability of water hyacinth pre-treated at 80 °C

Water hyacinth (Eichornia crassipes) is a fast growing aquatic plant which causes environmental problems in continental water bodies. Harvesting and handling this plant becomes an issue, and focus has been put on the research of treatment alternatives. Amongst others, energy production through biomethanation has been proposed. The aim of this study was to assess the anaerobic biodegradability of water hyacinth under mesophilic and thermophilic conditions. The effect of a thermal sludge pre-treatment at 80 °C was also evaluated. To this end, anaerobic biodegradability tests were carried out at 35 °C and 55 °C, with raw and pre-treated water hyacinth. According to the results, the thermal pre-treatment enhanced the solubilisation of water hyacinth (i.e. increase in the soluble to total chemical oxygen demand (COD)) from 4% to 12% after 30 min. However, no significant effect was observed on the methane yields (150–190 L CH₄/kg volatile solids). Initial methane production rates for thermophilic treatments were two fold those of mesophilic ones (6–6.5 L vs. 3–3.5 L CH₄/kg COD·day). Thus, higher methane production rates might be expected from thermophilic reactors working at short retention times. The study of longer low temperature pre-treatments or pre-treatments at elevated temperatures coupled to thermophilic reactors should be considered in the future.     

Determination of biogas generation potential as a renewable energy source from supermarket wastes

Fruit, vegetable, flower waste (FVFW), dairy products waste (DPW), meat waste (MW) and sugar waste (SW) obtained from a supermarket chain were anaerobically digested, in order to recover methane as a source of renewable energy. Batch mesophilic anaerobic reactors were run at total solids (TS) ratios of 5%, 8% and 10%. The highest methane yield of 0.44 L CH₄/g VS_added was obtained from anaerobic digestion of wastes (FVFW + DPW + MW + SW) at 10% TS, with 66.4% of methane (CH₄) composition in biogas. Anaerobic digestion of mixed wastes at 5% and 8% TS provided slightly lower methane yields of 0.41 and 0.40 L CH₄/g VS_added, respectively. When the wastes were digested alone without co-substrate addition, the highest methane yield of 0.40 L CH₄/g VS_added was obtained from FVFW at 5% TS. Generally, although the volatile solids (VS) conversion percentages seemed low during the experiments, higher methane yields could be obtained from anaerobic digestion of supermarket wastes. A suitable carbon/nitrogen (C/N) ratio, proper adjustment of the buffering capacity and the addition of essential trace nutrients (such as Ni) could improve VS conversion and biogas production yields significantly.     

Chemical characterisation of spent rechargeable batteries

A chemical characterisation of used batteries can give useful information to implement suitable recycling techniques and to estimate the flux of the different materials recovered. This work is aimed to provide quantitative data about the composition of mixed batteries (in particular, Ni–Cd, Ni-MH and Li-ion batteries) collected in a Northern Italian town in order to evaluate the feasibility of recovery processes applied to the selected material. The higher concentration of metals in the <3 mm fraction suggested that significant quantities of valuable elements could be recovered: in particular, for a kg of the <3 mm fraction deriving from disassembled batteries, about 390 g Ni and 330 g Cd can be recovered from Ni–Cd, 630 g Ni, 80 g Co from Ni-MH and 250 g Co, 110 g Ni, 120 g Cu from Li-ion ones. Leaching tests applied to the same fractions, to assess possible contaminant releases, resulted in low metal content in aqueous solutions (except for Al and Fe, the concentrations of all metals remained below 1 mg/kg). Even so, great care is required in all handling activities due to the high pH values of leachate solutions.     

Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants

In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm³ reactor, swept with 1 L min^?1 N₂, at 500 °C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33–40 MJ kg^?1). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO₂; their HHV is in the range of 18–46 MJ kg^?1. The amount of COCO₂ increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char.     

Valorisation of used cooking oil sludge by codigestion with swine manure

The addition of lipid wastes to the digestion of swine manure was studied as a means of increasing biogas production. Lipid waste was obtained from a biodiesel plant where used cooking oil is the feedstock. Digestion of this co-substrate was proposed as a way of valorising residual streams from the process of biodiesel production and to integrate the digestion process into the biorefinery concept.Batch digestion tests were performed at different co-digesting proportions obtaining as a result an increase in biogas production with the increase in the amount of co-substrate added to the mixture. Semi-continuous digestion was studied at a 7% (w/w) mass fraction of total solids. Co-digestion was successful at a hydraulic retention time (HRT) of 50 d but a decrease to 30 d resulted in a decrease in specific gas production and accumulation of volatile and long chain fatty acids. The CH₄ yield obtained was 326 ± 46 l/kg VS_feed at an HRT of 50 d, while this value was reduced to 274 ± 43 l/kg VS_feed when evaluated at an HRT of 30 d. However these values were higher than the one obtained under batch conditions (266 ± 40 l/kg VS_feed), thus indicating the need of acclimation to the co-substrate. Despite of operating at low organic loading rate (OLR), measurements from respirometry assays of digestate samples (at an HRT of 50 d) suggested that the effluent could not be directly applied to the soil as fertiliser and might have a negative effect over soil or crops.     

Anaerobic digestion of autoclaved and untreated food waste

Anaerobic digestion of autoclaved (160 °C, 6.2 bar) and untreated source segregated food waste (FW) was compared over 473 days in semi-continuously fed mesophilic reactors with trace elements supplementation, at organic loading rates (OLRs) of 2, 3, 4 and 6 kg volatile solids (VS)/m³ d. Methane yields at all OLR were 5–10% higher for untreated FW (maximum 0.483 ± 0.013 m³ CH₄/kg VS at 3 kg VS/m³ d) than autoclaved FW (maximum 0.439 ± 0.020 m³ CH₄/kg VS at 4 kg VS/m³ d). The residual methane potential of both digestates at all OLRs was less than 0.110 m³ CH₄/kg VS, indicating efficient methanation in all cases. Use of acclimated inoculum allowed very rapid increases in OLR. Reactors fed on autoclaved FW showed lower ammonium and hydrogen sulphide concentrations, probably due to reduced protein hydrolysis as a result of formation of Maillard compounds. In the current study this reduced biodegradability appears to outweigh any benefit due to thermal hydrolysis of ligno-cellulosic components.     

Combined processes of two-stage Fenton-biological anaerobic filter–biological aerated filter for advanced treatment of landfill leachate

There are numerous non-biodegradable organic materials in the mature landfill leachate. To meet the new discharge standard of China, additional advanced treatment is needed for the effluent from the biological treatment processes of leachate. In this study, a combined process including two stages of “Fenton-biological anaerobic filter (BANF)–biological aerated filter (BAF)” was evaluated to address the advanced treatment need. The Fenton oxidation was applied to reduce chemical oxygen demand (COD) and enhance biodegradability of refractory organics, and the BANF–BAF process was then applied to remove the total nitrogen (TN). The treatment achieved effluent concentrations of COD < 70 mg/L, TN < 40 mg/L and NH₃–N < 10 mg/L. The removal efficiency of COD and TN were 96.1% and 95.9%, respectively. The effluent quality met the new discharge standard for Pollution Control on the Landfill Site of Municipal Solid of PR China (GB16889-2008). The operation cost of these processes was about 36.1 CHY/t (5.70 USD/t).     

Experimental co-digestion of corn stalk and vermicompost to improve biogas production

Anaerobic co-digestion of corn stalk and vermicompost (VC) as well as mono-digestion of corn stalk were investigated. Batch mono-digestion experiments were performed at 35 ± 1 °C and initial total solid loading (TSL) ranged from 1.2% to 6.0%. Batch co-digestion experiments were performed at 35 ± 1 °C and initial TSL of 6% with VC proportions ranged from 20% to 80% of total solid (TS). For mono-digestion of corn stalk, a maximum methane yield of 217.60 ± 13.87 mL/g TS_added was obtained at initial TSL of 4.8%, and acidification was found at initial TSL of 6.0% with the lowest pH value of 5.10 on day 4. Co-digestion improved the methane yields by 4.42–58.61% via enhancing volatile fatty acids (VFAs) concentration and pH value compared with mono-digestion of corn stalk. The maximum biogas yield of 410.30 ± 11.01 mL/g TS_added and methane yield of 259.35 ± 13.85 mL/g TS_added were obtained for 40% VC addition. Structure analysis by X-ray diffractometry (XRD) showed that the lowest crystallinity of 35.04 of digested corn stalk was obtained from co-digestion with 40% VC, which decreased 29.4% compared to 49.6 obtained from un-treated corn stalk. It is concluded that co-digestion with VC is beneficial for improving biodigestibility and methane yield from corn stalk.     

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H₂S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS₂) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O₂ concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg^?1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H₂S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.     

Influence of pine wood shavings on the pyrolysis of poultry litter

Poultry litter from broilers and turkeys are a mixture of manure, feathers, feed and wood shavings, thus pyrolysis oils produced from this material are influenced by the individual components. In order to determine the influence of wood shavings that are used as bedding material, we investigated the pyrolysis of pine wood shavings and poultry manure. Because manure from layer chickens are usually not contaminated with wood shavings, we made mixtures of layer manure and pine wood shavings in the following manure to wood ratios, 100:0, 75:25, 50:50, 25:75, and 0:100 w/w and pyrolyzed them in a fluidized bed reactor at 450 °C. The total liquid yield ranged from 43.3 to 62.7 wt.%. The layer manure oil had a HHV of 29.7 MJ/kg and pH of 5.89 compared to pine wood oil which had HHV of 25.6 MJ/kg and pH of 3.04. The addition of wood shavings to manure clearly influenced the physical properties of the oil, resulting in a decrease in pH and HHV and an increase in density. The oils had relatively high nitrogen content ranging from 1.36 to 5.88 wt.%. The ash (<0.07 wt.%) and sulfur (<0.28 wt.%) contents were very low. FTIR, ¹³C NMR and ¹H NMR spectrometric analysis of the oils showed that manure oil was rich in hydrocarbons and nitrogenous compounds such as primary, secondary amides, aromatic amines and N-heterocyclic. The properties of the oils were strongly influenced by the amount of wood in the mixture.     

Analysis of the combustion and pyrolysis of dried sewage sludge by TGA and MS

In this study, the combustion and pyrolysis processes of three sewage sludge were investigated. The sewage sludge came from three wastewater treatment plants.Proximate and ultimate analyses were performed. The thermal behaviour of studied sewage sludge was investigated by thermogravimetric analysis with mass spectrometry (TGA-MS). The samples were heated from ambient temperature to 800 °C at a constant rate 10 °C/min in air (combustion process) and argon flows (pyrolysis process). The thermal profiles presented in form of TG/DTG curves were comparable for studied sludges. All TG/DTG curves were divided into three stages. The main decomposition of sewage sludge during the combustion process took place in the range 180–580 °C with c.a. 70% mass loss. The pyrolysis process occurred in lower temperature but with less mass loss. The evolved gaseous products (H₂, CH₄, CO₂, H₂O) from the decomposition of sewage sludge were identified on-line.     

Greenhouse gas emissions from landfill leachate treatment plants: A comparison of young and aged landfill

With limited assessment, leachate treatment of a specified landfill is considered to be a significant source of greenhouse gas (GHG) emissions. In our study, the cumulative GHG emitted from the storage ponds and process configurations that manage fresh or aged landfill leachate were investigated. Our results showed that strong CH₄ emissions were observed from the fresh leachate storage pond, with the fluxes values (2219–26,489 mg C m^?2 h^?1) extremely higher than those of N₂O (0.028–0.41 mg N m^?2 h^?1). In contrast, the emission values for both CH₄ and N₂O were low for the aged leachate tank. N₂O emissions became dominant once the leachate entered the treatment plants of both systems, accounting for 8–12% of the removal of N-species gases. Per capita, the N₂O emission based on both leachate treatment systems was estimated to be 7.99 g N₂O–N capita^?1 yr^?1. An increase of 80% in N₂O emissions was observed when the bioreactor pH decreased by approximately 1 pH unit. The vast majority of carbon was removed in the form of CO₂, with a small portion as CH₄ (<0.3%) during both treatment processes. The cumulative GHG emissions for fresh leachate storage ponds, fresh leachate treatment system and aged leachate treatment system were 19.10, 10.62 and 3.63 Gg CO₂ eq yr^?1, respectively, for a total that could be transformed to 9.09 kg CO₂ eq capita^?1 yr^?1.